Search Documents

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

During the extensive research which has been conducted in the Metallurgy Department of the University of Melbourne, into the properties of lead and its dilute alloys, the Brinell test has been used for the determination of hardness.The work described herein represents part of an investigation into the influence of various factors on such determinations, particularly when carried out on different qualities of "pure" lead. It is intended to publish the more theoretical and controversial aspects of this research elsewhere.MATERIALS USED AND THEIR PREPARATION FOR TESTINGThe tests to be reported have been conducted on a specially pure electrolytic lead, and several brands of commercially "pure" lead. The analyses of the samples upon which most of the work has been carried out are given in Table 1.Note: Oxygen was not determined, but from the work of H. W. Worner, in the Rosenhain Memorial Laboratory, it appears probable that it was approximately 0-0003% in all samples.

Jan 1, 1940

By CLARESCE CARLETON SEJIPLE

(Wilkes-Barre Meeting, June, 1911.) AT a number of mines in eastern Nicaragua, 3.5- and 5-ft. Huntington mills are used for grinding gold-ore after a preliminary breaking in jaw-crushers. The smaller mills are made sectional to facilitate transportation to the more difficultly accessible mines. The capacity of the smaller mills is about 20 or 25 per cent. that of the larger, but in proportion to the quantity of ore ground they require more power and are subject to greater wear. The notes herein given are from records of the performance of the larger mills, but, in general, apply to the smaller also. THE NATURE OF THE ORE. The ore occurred as a series of flat veins in a highly-decomposed rock, probably alaskite. The primary mineralization comprised pyrite, pyrrhotite, marcasite, chalcopyrite, and quartz; the oxidation-products of which were chiefly hydrated iron oxide or limonite, chrysocolla, azurite, and malachite. The kaolinization of the feldspar of the country resulted in the admixture of a great quantity of clay with the oxidized ore. The quartz was sandy, imbedded in the clay; and probably the greater part represented the residue from the crushed rock in the fissures after leaching, and kaolinization of the feldspar. There was little vein-quartz in the unaltered primary sulphide ore. Only the oxidized ore was mined for the gold that it contained in amounts that averaged $4 per ton. No specks of gold were ever seen in the ore, and the gold obtained by panning was always exceedingly fine. The amalgamation-bullion was about 800 fine in gold and 60 to 80 in silver. The ore delivered at the mill contained from 5 to 15 per cent. of moisture; during the rainy season the quantity was much greater. The moisture and clay made the ore so sticky that it had to be raked over steeply-inclined grizzlies; it hung in the ore-bins,

Oct 1, 1911

By J. J. Taber

This is the final report on Grant No. G0144067. The report presents the results of a number of laboratory studies carried cut in several different ways to determine the effectiveness of foam for blocking the flow of gas in coal. The effectiveness; (of foam for retarding or blocking the flow gas in various porous media has been observed by many investigators1-4 but we are not aware of similar detailed studies in coal. Because of the diversity of our experiments, the key findings and general conclusions are presented very briefly in Section II. As a convenience to the reader a complete table of cements is included to enable the reader to find those experiments and studies of greatest interest.

Jan 1, 1976

By Roberto Chambi

El presente texto describe las experiencias relacionadas al desarrollo e implantación del Sistema deTopografía para la mina subterránea de produccción polimetálica Raura. Para ello, se desarrolla la importancia de la topografía en el diseño y los proyectos mineros a través de un sistema de cálculo y dibujo topográfico. Los principales objetivos del sistema son: la gestión de la base de datos topográficos de la mina, la sustitución de las operaciones matemáticas “manuales” y la eliminación de sus errores inherentes, así como realizar automáticamente los dibujos de labores mineras a partir de la data recolectada y procesada, tanto en cálculos como en dibujo. De forma que se genera información procesada a los software especializados en geología y planificación.

May 25, 1998

By François G. Bernardeau

Cement-bentonite (C-B) slurry walls have been used for ground water cutoff in deep excavations, contamination containment, and other applications. Hydraulic conductivity is of great concern for cement-bentonite slurry walls. The quality control program usually specifies permeability and strength tests to be performed in a laboratory on samples cast in the field and cured for a certain time. Currently there is no widely accepted in-situ test method for the performance of the constructed slurry wall. A recently constructed cement-bentonite slurry wall in South Carolina included a 200-foot-long test section done in advance of the production of an 8,300 foot-long wall. Intensive tests and investigation were conducted during and after the test section construction: Monitoring piezometers were installed using wet insertion method and packer tests were conducted in boreholes drilled in the post-28-day-cure slurry wall. The permeability measured from the packer tests was about two orders of magnitude higher than the design and the laboratory test values. Additional investigation was performed using a video camera to inspect the borehole walls especially the packer test sections. Test pits were excavated to observe both sides of the cement-bentonite slurry wall. A thorough inspection was conducted to evaluate the integrity of the wall. The lessons learned and issues regarding the disturbance effects of in-situ testing of cement bentonite slurry walls is presented and discussed.

Jan 1, 2008

By Steve Hubbard, Brad Marchant, Rolando Cuadra

"Triton Mining Corporation acquired the rights to Mina El Limon in Nicaragua in 1993 by international bid. The bid included the gold operations at Limon and an exploration concession of approximately 4000 km2. Triton assumed control of operations and exploration in May 1994.The Limon mine is located in west-central Nicaragua, approximately 100 kilometers northwest of Managua. The climate is tropical, characterized by a wet season from May through October, and a dry season November through April. Gold at Limon is associated with both banded quartz and silicified breccia veins in Tertiary volcanic rocks, belonging to the lower Coyol Group. Mining is from two open pits and one mechanized underground operation. A second underground mine is currently under development for production during 1997.This paper describes the expansion of the milling facility at El Limon from a nominal capacity of 400 tonnes/day, producing approximately 20,000 ounces of gold annually, to the existing 900 tonne per day mill operation. Engineering of the new mill facility was initiated in September 1994 and construction was completed a year later."

Jan 1, 1997

By D. R. Zuchelli

In order for MSHA to require the use of a noise control, the control must be proven ?technologically feasible?. Technologically feasible controls must reduce a miner?s noise overexposure to the permissible exposure level (PEL) or achieve at least a 3 dBA reduction in the miner?s noise exposure. The miner?s total noise exposure should be examined from an occupational viewpoint and not solely on a machine or equipment basis. This examination requires a field evaluation of the occupation as opposed to an equipment test conducted in a laboratory. The operator of a Hilti TE MD20 LS electro-pneumatic drill realized a full shift noise exposure (TWA8) reduction exceeding 8 dBA as compared to when operating a Gardner Denver S83F pneumatic jackleg drill while installing an equal number of drill holes into the Idaho Springs Gneiss rock formation. However, the Hilti drill?s penetration rate was only 27% of that of the jackleg drill. Although the Hilti drill was proven to be technologically feasible as a noise control, its slower penetration rate would require its economic feasibility to be evaluated on a case-by-case basis.

Jan 1, 2011

By E. F. Schnitzer, D. R. Haight, G. T. Krogman

The 1997 New Year’s Day Rogue River flood near Medford, Oregon, USA, entered historic channels, eroded a 150-foot-wide buffer, and captured an inactive gravel pond located within the channel migration zone. Channel redirection caused by pit captures threatened adjacent inactive gravel ponds. In response to this capture, a stakeholders group of concerned individuals and organizations was formed. This group ultimately developed a rehabilitation plan, which conformed to the Rogue River’s geomorphic trends. A two-dimensional model, FLO-2D, was used to evaluate channel splits, flood storage, backwater, and future conditions. Modeling results coupled with trend analysis were used to create a stable design where stream barbs, gravel redistribution, a channel outfall spillway, bendway weirs, bank reshaping, and revegetation were integrated into a single plan for a three-mile reach. The quick action by the stakeholders group averted further damage to the Rogue River system and surrounding environment. The project has preserved three miles of mainstem habitat, one mile of side channel habitat, and protected ten gravel ponds from pit capture.

Jan 1, 2006

By W. Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due to quarry blasting.

Feb 1, 2020

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989

By Albert Wraith, Thomas Price, Wayne Boyd, Skip (I. E. ) Hills, Cameron Harris

Most Peirce-Smith converters inject air through tuyeres, with nitrogen representing the majority of gas passing through the process. The nitrogen controls the temperature of the vessel by carrying away heat from the reactions, both globally and locally at the tuyere tip. However, nitrogen adds energy to the bath and contributes to splashing and limits the blowing rate. High oxygen smelting has made streams of gas containing high concentrations of sulphur dioxide commonplace, which can be used to substitute SO2 for nitrogen and drastically changes Peirce- Smith converting (and all other smelting/converting processes as well). Less SO2 is required to carry away the same quantity of heat, which allows higher concentrations of oxygen and leads to the possibility of increased production. The paper investigates this substitution, its impact on converter productivity, and on the remainder of the plant. 181

Jan 1, 2009

By Spencer P. Howell, Munroem Charles E.

"Introduction;As in the case of TNT previously presented*, this report presents the results of an investigation to discover the safest and best way of utilizing picric acid for industrial blasting purposes. It describes the physical and chemical properties of this explosive, gives precautions to be observed in handling, packing, preparation of cartridges, and holes, presents the results of field tests in blasting stumps and bowlders, and compares the results with those obtained from dynamite.The investigations reported herein were undertaken and this paper has been prepared, solely to aid in the salvage of the surplus picric acid accumulated for war uses and released by the declaration of the armistice. No funds were available nor have any been appropriated with which to defray the expense of converting this picric acid into any other form or to prepare any explosive mixture from it. The sole problem was to find appropriate uses for this military picric acid in existing needs and to show that it can be efficiently used in carrying out essential civil projects.It is not intended by this publication to promote the use of picric acid as an industrial explosive further than is necessary for the proper utilization of this surplus. On the contrary, the authors believe that picric acid by itself is unlikely to come into general use as an industrial explosive, chiefly because of its cost but also as shown by the clouds of smoke it emits on explosion and the nature of the reactions it undergoes because we do not obtain from it its highest efficiency. As demonstrated in its previous use in Joveite, better results and higher efficiencies may be obtained by mixing picric acid in proper proportions with sodium nitrate or ammonium nitrate, to more completely oxidize the picric acid, and another nitrosubstitution compound, such as nitronaphthalenes, with which do desensitize and waterproof the composition formed. By such admixture not only may the energy resident in the picric acid, be more fully utilized but the cost of the resulting blasting explosive should be much less than that of picric acid."

Apr 1, 1921

After a five year period representing the strongest resource and commodity rally ever experienced, we are now faced with a subdued recovery following the global financial crisis. This renewed economic growth will be steady but eventually attain levels that reignite export demand out of China and other emerging nations, which are now reliant on increasing domestic demand to support their economies. This backdrop of weaker share prices and less available investment capital creates a greater imperative for company management to ensure that its share price is fully valued. The mining geologist plays an important role in achieving this outcome through direct estimation of asset value (resources) but also in strongly communicating the æupsideÆ value opportunity in both mine site and adjacent brownfields exploration and an efficient and technically sound mining operation. The contribution of mining geologists to assist in conducting analyst site visits should not be underestimated, particularly with reduced analyst coverage of the resources sector and some simplification in company analysis through ranking companies on Reserve and Resource positions.

Jan 1, 2009

By N Merry, T Cocks

The mineral exploration industry is increasingly aware of the importance of the relationship between mineralogical data and geochemical assay results. However, until recently, the cost and time constraints of most techniques for analysing alteration mineralogy have precluded detailed alteration studies. These impediments have been reduced by the development of the Portable Infrared Mineral Analyser (PIMA), a field portable infrared spectrometer that allows rapid (in field) and cost effective analysis of alteration minerals including subtle variations in mineral crystallinity and composition.   A major application of this technology is in mapping mineralogical variations within hydrothermal alteration systems. Using actual case study examples this paper introduces two approaches to using the PIMA data: 1. for directly mapping alteration systems and using the PIMA data to provide vectors to mineralisation, and 2. for establishing empirical relationships between geochemical data and PIMA spectral data. These applications demonstrate that this technology can be an invaluable tool for targeting and mapping alteration and mineralisation.

Jan 1, 1995

By deur R. Dippenaar

'n Kort kursus oar die teorie en praktyk van hittebehandeling is vanaf 29 Junie 1981 tot 3 Julie 1981 in die departement Materiaalkunde en Metallurgiese Ingenieurswese aan die Universiteit van Pretoria aangebied. Die kursus is dour dosente van die departement opgestel en in samewerking met 'n aantal gassprekers aDder beskerming van die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie aangebied. Tunnelling The Third International Symposium on Tunnelling is to be held in Brighton from 7th to 11th June, 1982. Professional development seminars The Department of Mining and Metallurgical Engineering of McGill University is to hold the following seminars during 1981-1982.

Jan 1, 1981

By Tom Dettweiler, Robina Sharpe, Wright. Michael

The International Seabed Authority and a number of countries have or are in the process of developing environmental impact assessment guidelines and legislation for seafloor mineral development. The formal decision to grant a project an environmental permit is based on an environmental and social impact assessment (ESIA), culminating in an environmental impact statement (EIS). The EIS needs to be supported by sufficient data upon which an assessment of impacts can be made and mitigation measures developed. Given the remote locations of many seafloor prospects, collection of sufficient environmental data to inform an EIS is often a difficult, expensive and lengthy process.

Sep 1, 2014

By Lifeng Zhang

The transport of fluid, heat ,and particles (bubbles and solid inclusions) in flowing molten steel is investigated in steel refining ladles, the continuous casting tundish, continuous casting mold and strand, and steel ingot casting processes. The two-equation k-?? model is used to simulate the turbulence. Multiphase fluid flow is numerically simulated with a Lagrangian-Eulerian approach, an Eularian-Eulerian approach and the Volume Of Fluid (VOF) method. The simulation can predict inclusion trajectories, inclusion removal fraction, free surface waves and other phenomena, which can be used to optimize these important metallurgical operations.

Jan 1, 2006

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By J. W. Wang

This article first explains the mechanism of forming strength in the Jet grouting reinforced foundation, and points out the function of cement hydrates and clay minerals in clayey soil, the reinforced body with the character of long-term growth of strength. Secondly, regarding the strength and the deformation characteristics of compound foundation, the article points out that the stress-strain curve of the jet grouting pile is approximate to hyperbolic curve. Finally, the article cites three examples of application in the construction of the metallurgical industry.

Jan 1, 2010