Search Documents

By Jorge Madias

Pin holes as a surface defect, and blow holes as an inner defect, occur in billet / bloom / beam blank casting, particularly for Si-Mn killed steel cast with metering nozzle and oil lubrication. If they are present in abundance or have a large size, they may originate defects in the rolled products. Their characteristics, factors behind their formation, as well as usual processing conditions that promote their occurrence are discussed. Finally, the evolution of these defects during reheating and rolling is analyzed, with industrial examples.

Aug 16, 2017

By EDBIUND U. NORTH

IN making a glass model of mine-workings, each mine will present some little individualities, to meet which will call for the exercise of special ingenuity. Having made several models, I offer the following details of the model of the Montana-Tonopah mine-workings, believing that with small changes for different conditions the method described can be successfully used in making a glass model of the workings of any mine. The model, Fig. 1, has the top, one end, and the front removed. The case is made of kiln-dried pine, painted with several coats of dead-white paint. It is made to take sheets of glass 24 by 42 in. in size, and is 18 in. high, the workings shown being on a scale of 1 in. = 40 ft., or 4800 : 1 scale. The base is made of four pieces of 2-in. material, well pinned and glued together. The back, of material 1 in. thick, is secured rigidly to the base by screws and countersinking. The four posts, 1.5 in. square, are so cut that. the front and two ends of the model fit in flush with the outside edges of the posts. The top rails, 1 in. square, are fastened rigidly to the front and back posts by means of small iron braces. The ends, front, and top of the case are of 0.5-in. material; the ends and front are held in place at the bottom by pegs fitting into the base ; at the top the ends are held by buttons and the front by cupboard-hooks on the inside. Hinged hasps on the cover, fitting over staples in the end-pieces, make it easy to lock the entire case. Before the back is fastened to the base, it is cut with horizontal and vertical grooves to receive the horizontal and vertical sheets of glass, shown clearly in Figs. 1 and 2. The horizontal grooves, spaced to scale, represent the vertical distances between the levels at the shaft. The vertical grooves are placed wherever cross-sections of the workings are desired.

Jan 1, 1910

By D. W. Fuerstenau

One of the more energy-efficient methods for size reduction, namely particle-bed comminution under high compressive loads, was employed to grind eight minerals and ores, using up to 250 MPa pressure. A new approach based on the self-preserving character of the ground product size distributions and a linear energy-reduction ratio relationship is proposed for analyzing this mode of size reduction. The grind ability of the material when comminuted in a particle bed is about one-half that of the single-particle crushing mode, which is in agreement with previous estimates of the relative efficiencies of energy utilization based on direct measurements of surface area produced. The loss of efficiency may be attributed to energy dissipation by particle interaction phenomena in compressed beds.

Jan 1, 1993

By Alexandre de Freitas Gomes de Mendonça

A remoção de inclusões nos distribuidores de lingotamento contínuo tem sido investigada por meio de modelamentos físicos e matemáticos. Recentemente, a injeção de gás nos distribuidores tem sido considerada como uma alternativa para aprimorar a remoção de inclusões. Vários trabalhos vêm sendo desenvolvidos analisando os efeitos da injeção de gás e sua interação com as inclusões. No entanto, existe espaço para mais investigações envolvendo o efeito da vazão do gás e a localização do sistema de injeção de gás na eficiência de remoção de inclusões. No presente trabalho, foi usado um modelo físico construído em escala 1:3 de um distribuidor industrial de 40 toneladas de capacidade nominal, para analisar o efeito da injeção de gás. Os experimentos incluíram contagem on-line de partículas pela sonda APS III e análise de curvas DTR. O resultado mostrou que a injeção de gás é benéfica à remoção de inclusões e que a análise pura dos volumes característicos, calculados a partir das curvas DTR, não é suficiente para avaliar a eficiência de remoção.

Aug 17, 2017

By T. Szendrei and S. Tose

Historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques, are inherently incapable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study.

Dec 13, 2022

The selection of the mining fleet can have as much of an effect on the efficiency and effectiveness of an operation as the mining method. This is not to say that inefficiencies are only attributable to inappropriate equipment selections, these aspects have many factors but are not the subject of this paper.This paper will give an overview of equipment selection processes that have been utilised to date. It will also look at the increase in application of study programs/simulations from an aspect of accuracy, as well as the importance of enabling the analysis of multiple sensitivity scenario planning. An aspect that is increasingly important in project planning with commodity market movements.Another aspect that is increasing in popularity is that of automation, what effect does this have on equipment selection? What additional aspects need to be taken into consideration when assessing Automation of equipment from the beginning of a project as well as introduction into an operating mine?Once the selection process has been finalised and equipment implemented, how do we, as an industry, 'close the loop' through analysis of estimated versus actual equipment application?

Dec 6, 2010

By Charles R. Graig

El Laboratorio de Espectrografía del Departamento de Investigaciones de la Cerro de Pasco Corporation, elaboró un método de control de los circuitos de flotación por espectrografía de rayos - X. El método se basa en el uso de técnicas especiales de preparación de la muestra, los productos del circuito de flotación, y la fusión con pirosulfato de potasio. En este sentido, el objeto del texto radica en describir el procedimiento de la determinación cuantitativa por espectrografía de rayos-X, de las concentraciones de plomo, zinc, cobre y fierro en las cabezas, los concentrados y las colas de los circuitos de flotación. Es importante considerar el diseño del laboratorio de rayos X para la elaboración de los resultados de planta dentro del tiempo especificado. Así, el control de los procesos de flotación permite la rápida obtención de resultados exactos, lo cual hará posible una mejor regulación de los reactivos de flotación añadidos a los circuitos, mejorando el proceso.

Nov 20, 1967

By J. B. Mawdsley

"AbstractThe uraninite-bearing deposits in the Charlebois Lake area of northeastern Saskatchewan are unusual and important concentrations of uranium. They were first discovered in 1949 and preliminary development work to the end of the 1951 field season indicates the probability that this will become •another uranium producing district. The deposits are in zones bordering granite masses. These zones are of migmatite (mixed rocks) composed of calcium-rich meta-sediments intruded and replaced by a fine-grained white pegmatite. Locally this pegmatite is replaced by an end fraction which is relatively rich in fine-grained disseminated uraninite; it is these occurrences that constitute the bodies of economic interest.The fine-grained white pegmatite contains plagioclase feldspar more lime-rich than that in the granites of which it is an end differentiate. This extra lime, evidently derived from the intruded sediments, would result in the raising of the temperature of crystallization of the pegmatite-forming magma, thus consolidating it rapidly near the granite contacts as a fine-grained pegmatite. The end liquor containing uranium was evidently locally concentrated in minor fracture zones in these pegmatites. Where no lime sediments were present. the coarse-grained alkaline pegmatites were formed. Their crystallization would not be accelerated and the uranium would tend not to be localized in the pegmatite but to migrate and consolidate at lower temperatures with the end products, possibly in some instances as pitchblende veins."

Jan 1, 1952

By Ernesto Valdez Bustamante

La etapa previa a la hidrometalurgia y recuperación por electrolisis en el proceso de producción del zinc, se realiza mediante la tostación. En este proceso, el concentrado de zinc es convertido en óxido de zinc y el dióxido de azufre es expelido. Para realizar este procedimiento, la planta de tostación utliiza 2 tostadores tipo wedge, 3 tostadores de cama fluidizada y uno de cama turbulenta fluidizada. Sin embargo, luego de un análisis exhaustivo, se encontró que los primeros tostadores tenían poca capacidad de concentración, considerándolos inhabilitados. Mientras que los segundos requieren una alimentación especial en forma de perdigones, necesitando una planta perdigonadora que eleve el costo de producción. En ese sentido, el objetivo del texto describe el funcionamiento del tostador de cama turbulenta fluidizada en la planta electrolítica de zinc de la Cerro de Pasco Corporation, como el equipo adecuado para el tratamiento de los concentrados de zinc, sin una aglomeración previa.

Nov 20, 1967

By D. E. Keeley

lntroduction Some years ago it was general practice in Canadian mines to use the best timber available, just as it was cut from the tree. Later, to prevent 'borers' from getting into the wood while stacked in the yard, the bark was peeled off, cleaned up carefully, and burned to eliminate a breeding ground for these and other destructive insects. This practice of good housekeeping also decreased the hazard from fire in scattered bark. A few years after damage by borers had been minimized, it became apparent that increased temperatures in the mines, occasioned by deepening operations, were being accompanied by rapid growth of fungus and by decay in timber underground, greatly shortening its life. In places on upper levels where the air temperature was below 50 deg. F., untreated timber retained a large proportion of its strength for ten or more years. In other places on these levels, however; its life was short and it developed much dry rot and merulius lacrymans. In these latter places and on lower levels in the mine where temperatures ranged from 50 to 60 deg. F., approximately, the wood became infested with extensive growths of this white fungus. This development was accompanied by the production of millions of spores. Spread of infection was due mainly to the transfer of spores from the warm lower levels to the cool upper horizons by upcasting ventilation currents. So serious did this become that about twenty years ago Lake Shore, Hollinger, and McIntyre Mines decided to investigate the use of wood preservatives and the plant necessary to treat timber.

Jan 1, 1949

By Tom Blevins, Roland Walker, Jinsheng Chen

"The Dywidag-Systems International DSI Tandem Anchor bolt, with an improved expansion shell-washer design, can substantially reduce potential entry roof falls caused by twisted or deformed expansion shells of the traditional mechanical anchor bolts during installation. In addition, the improved anchorage system can also ensure that a consistent and high installed load is achieved, which is critical for effective beam building under thinly laminated or layered roof conditions. This paper discusses the genesis and anchorage performance of the Tandem Anchor bolt, and analyzes the tension/torque relationship of different mechanical shell anchors using data obtained from both lab and field tests. It also discusses roof bolting mechanisms, roof bolting systems, and factors influencing effective beam building. Finally, numerical modeling was used to analyze the effect of bolt pretension magnitude on entry roof stability.INTRODUCTIONThroughout the history of underground mining, keeping the roof from uncontrollable collapse has been the greatest concern of the miner. Tremendous strides have been made in better understanding, predicting, and supporting the mine roof. This conference has spent the last twenty-eight years sharing information and distributing it to the mining community. A paraphrased statement from former Secretary of Defense Donald Rumsfeld adequately describes the challenges to the mining engineer as it pertains to roof control: it is a study of known knowns, known unknowns, and unknown unknowns. It is the hope of the authors to address some of these unknowns.The paper discusses the development of bolt anchorage systems from dry shells to shells with resin-assisted anchorage. It looks at some of the issues faced with the anchorage shells being used when introducing the insertion pressures caused by resin cartridges. The rationale behind the shell design changes was to compensate for this resin induced stresses.An improved expansion shell assembly (a slotted expansion shell base, a tapered cramming plug, and a novel support nut with tapered top) for mine roof bolts makes up the Tandem Anchor (U.S. Pat. No. 6742966); this minimizes the possibility of twisting seen with traditional mechanical shells and thus prevents springy bolts and shell leaves from breaking. A fully grouted Tandem Anchor bolting system has the advantages of both the pure mechanical point-anchor and the non-pretention fully grouted bolting systems. Once installed, the installed load or pretension will be locked in and never bleed off. Compared with the fully-grouted (2-speed resin) tension rebar bolting system, the fully-grouted Tandem Anchor bolting system can (a) reduce bolting cycle time (about 15 seconds per bolt), boosting coal production and productivity; (b) provide a greater installed load or pretention; and (c) achieve a consistent tension/torque ratio, which gives better bolting quality control. Therefore, a fully grouted Tandem Anchor bolting system is the most effective means to reinforce a weak rock mass intrinsically by the theory of beam building. For thinly laminated or layered roof conditions, a higher installed load or pretention (50% or more of the bolt's yield strength) can make a roof bolting system much stiffer, which results in less roof movement. Numerical modeling results show that the magnitude of the roof's tensile stress and relaxation zone can be substantially reduced under a higher installed load or pretention."

Jan 1, 2010

By Renate Wellen, Olgun Guven, Mariane Y. T. Oide, Julyana Satana, Francisco Valenzuela-Díaz, Esperidiana Moura

Poly[(ethylene)-co-(vinylacetate)] (EVA) is a thermoplastic copolymer composed of randomly distributed polyethylene and polyvinyl acetate sequences within the molecular chain. EVA combines toughness with excellent flexibility, impact and puncture resistance. Because of these properties, this material is largely used for foam production as padding in equipment for various sports and as a shock absorber in sport’s shoes. This work aims to study the influence of clay reinforcement on the performance of recycled polymer foams. The blend containing recycled HDPE (high density polyethylene) and recycled EVA (70/30 wt%, respectively) reinforced with 2 wt%of clays were prepared by melt extrusion, using a twin-screw extruder to obtain the composites. The composites and foaming agent were fed into a special single screw extruder for foaming. The samples of HDPE/ EVA/Clay foams were characterized by tensile test, Field Emission Scanning Electron Microscopy (FE-SEM), Thermogravimetric Analysis (TG), Differential Scanning Calorimetry (DSC), X-ray Diffraction (XRD), density measurement and the correlation between the results was evaluated.

Mar 1, 2018

By Roger Escoda Estelrich, Joan Carles Casado Ortega, Mitchell Gerdau, Jose Raul Martinez, Jeb Pittsinger, Frank Perrone

The existing Chesapeake Bay Bridge-Tunnel complex is being expanded to include the Parallel Thimble Shoal Tunnel. This will be a subaqueous bored crossing between two islands constructed for the original 1960s immersed-tube tunnel. Jet grouting was employed by the Chesapeake Tunnel Joint Venture (CTJV) to provide watertight base plugs, launch and retrieval blocks for the tunnel boring machine (TBM), a TBM canopy to limit ground movement, and a retaining wall to enable off-island excavation: all within hydraulically placed sands. This paper will review the design and construction challenges, including soil permeability and recharge, grout communication, installed grout strengths, and remediation requirements.

Jun 23, 2024

By G. G. Lambert

The paper traces the pattern of spontaneous combustion in the workings of what was originally Hemsworth Colliery, but since July 1967 is now part of South Kirby Colliery. Examination is made of the Barnsley Seam sections and the part played by the top section of the seam as it comes in close proximity to the main seam. In this area of the colliery nine mechanised faces were set away between the years 1953 and 1968, every one "fired" at the pillar edge and six "fired" at the face line when production had ceased. The paper deals with the different preventative measures used, from sandbag walls, cement injections, spraying with polyurethane, until finally using Mandoseal as a sealant. Since the latter method was first used, the last three faces worked in this particular area were all salvaged completely, without any sign of a heating developing.

May 23, 1905

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By H. M. Maturano

"Los métodos geoeléctricos de detección de fugas se utilizan en obras de ingeniería civil con el fin de mejorar los sistemas ambientales y de producción En ese sentido, el presente texto señala los métodos aplicados para detectar daños en la geomembrana expuesta como el método Lanza de Agua y Bipolar. El primero consiste en la aplicación de un potencial eléctrico entre el suelo ubicado debajo de la geomembrana y el agua esparcida en la superficie de la misma, mientras que el segundo, expuestas, mientras que el método Bipolar tiene como finalidad localizar fugas en la geomembrana luego de haber sido recubierta con algún tipo de material. Para el caso de plataformas de lixiviación, se han realizado cálculos de costo/beneficio sobre la aplicación de programas de detección de fugas, concluyendo que resulta económicamente rentable su ejecución comparada con las pérdidas de solución rica en mineral a través de los agujeros por largos períodos."

May 1, 2016

By Y. Paul Chugh

NIOSH and the Illinois Clean Coal Institute are funding studies on characterization of coal and quartz dust in Interior Basin mines since 2009. Coal dust characteristics vary significantly and, are vital for the development of the engineering controls. This paper presents wettability characteristics of coal dust with respect to its chemical and physical properties, since wettability is considered to be a primary dust control technique. Particle size distribution, inter-particle interactions during wetting and quartz associations with organic and inorganic matter in coal seams is critical for understanding wetting phenomena. Silica content in the un-wetted fractions was found to be very high during wetting tests. Wetting of quartz may be limited by its association to hydrophobic materials as well as buoyancy forces resulting from particle size characteristics and particle-particle interaction in the wetting agent. Temperature of the wetting solution and effective contact time between dust particles and water droplets are found to be two important variables affecting the wettability. The characterization data obtained from this study can be utilized to develop engineering controls.

Jan 1, 2011

By Joseph Chalmers

The Petroleum Experiment Station of the U. S. Bureau of Mines at Bartlesville, Okla., has for the past three and a half years maintained a laboratory with the necessary personnel for conducting research on methods of increasing the recovery of oil. Some of the preliminary problems encountered in starting this work, with the data obtained, were discussed in A. I. M. E. Technical Publication No. 144, "Oil Recovery Investigations of the Petroleum Experiment Station of the U. S. Bureau of Mines," which was presented at the October meeting of the Institute at Tulsa, Okla., in 1928. Scope of Paper The following discussion gives some of the results of the more recent work at the Oil Recovery Laboratory. These experiments were conducted to obtain laboratory data pertaining to the relative merits or efficiencies of various pressure media in the recovery of oil from a sand reservoir. Two general types of experiments were conducted. In one the various pressure media were passed through an artificial body of sand partly saturated with oil at a constant input pressure; in the other the pressure media were passed through the body of sand partly saturated with oil at a constant volume rate. No attempt will be made to discuss the ramifications of economic problems which enter into the choice of a pressure medium. Apparatus and Materials The two 6-in. by 6-ft. flow tubes described in Technical Publication 144 were used in these experiments. They consist of 6-ft. sections of 6-in. casing with a blind flange at each end. There are three 1-in. well openings in each tube, spaced 2 ft. 4 in. apart, the end wells being

Jan 1, 1930

By Brian Cochran, C. Edward Eckert

"EXECUTIVE SUMMARYINTRODUCTIONThe commercial incentives for using molten aluminum in casting operations are numerous and substantial. Although these incentives apply broadly to both shape castings (foundry) operations and wrought alloy production, the merit of a particular motive is indeed downstream processing sensitive. Melting cost reduction is a universal incentive that impacts on essentially all aluminum products. At a natural gas burner cost of $4.50 per therm, for example, the reverberatory furnace energy cost is at least $0.01 per pound of aluminum melted, exclusive of melt loss, fixed costs, and other expenses. The Aluminum Statistical Review' cited 3.188 million metric tons of secondary aluminum that was recovered by the industry in 1995. This represents a re-melt energy cost of over $70 million. Other incentives to use molten secondary aluminum include throughput enhancement, metal chemistry assurances, environmental considerations, and the avoidance of an in-house scrap processing operation.A traditional disincentive to use molten secondary aluminum is metal quality. If a particular secondary processing operation was successful in achieving and preserving an acceptable metal quality level prior to shipment, the subsequent metal transfer and ladle delivery events would frequently obviate these efforts. For example, a metal superheat on the order of several hundred degrees is required for an unheated transfer ladle to travel 3 to 4 hours to a customer location. The rate of the y-alumina formation reaction approximately doubles for every 120°F increase in temperature, therefore, the effect of excess superheat on melt loss and metal quality is considerable. Linear oxidation reactions, such as magnesia formation in magnesium containing alloys, are influenced to an even greater extent by temperature.The typical quality detractor events are:"

Jan 1, 2000

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018