Search Documents

By William W. Adams

The quarrying and related industries of the United States made a large gain in employment (man-hours of work) in 1942 with a somewhat smaller number of men employed than in 1941. This was accomplished chiefly by increasing the number of workdays per man and also by increasing the length of the workday. In spite of the greater volume of work performed, the industry had a more favorable accident-frequency rate in 1942 than in the previous year. Accident and employment reports from operating companies showed that the industry employed 84,270 men for an average of 271 days per man in 1942, with a volume of work of almost 181 million man-hours. The average workshift comprised 7.93 hours, and the number of man-shifts worked totaled nearly 23 million. Injuries from accidents in and about the quarries and plants caused disability to 6,461 employees, 112 of whom died as a result of their injuries, including 28 employees whose lives were lost in a single disaster. The accident-frequency rate in the industry was 35.73 per million man-hours worked, comparing favorably with a rate of 40.11 for the previous year. However, the figure for 1942 included a death rate of 0.62 per million man-hours which, because of the disaster referred to, was considerably higher than the fatality rate of 0.44 for 1941. Had the disaster not occurred, the fatality rate for the industry for 1942 would have been 0.46. The major disaster in which 28 lives were lost occurred on March 26 at the Sandts Eddy quarry of the Lehigh Portland Cement Co. near Easton Pa.

Jan 1, 1944

By Ana Carolina Ribeiro Duarte

Este trabalho teve por objetivo avaliar sistematicamente as etapas do processamento termomecânico de um aço SAE 1070 comercial. O aço foi trefilado a seco por 12 passes consecutivos com reduções médias entre 15% e 21%. A deformação verdadeira acumulada ao final do 12º passe foi de 2,52. Em seguida o material foi recozido a 1000ºC por 10, 20, 30, 60 e 120 min. A caracterização microestrutural foi realizada com o auxílio da técnica de microscopia óptica, microscopia eletrônica de varredura e microscopia de força atômica. A rugosidade do material foi medida via microscopia confocal. O material teve ainda seu comportamento mecânico avaliado por meio de ensaio de dureza Vickers. Os fios de aço apresentaram a estrutura “curling” após o processo de trefilação. Essa estrutura foi substituída por uma estrutura perlítica refinada quando o material foi submetido ao recozimento. O ensaio de microdureza mostrou que, para restaurar as propriedades mecânicas do material, um recozimento entre 20 e 30 min seria suficiente. A análise da topografia revelou que o processo de trefilação altera consideravelmente a rugosidade do material.

Aug 8, 2018

By J. W. Kramers, R. A. S. Brown

"Samples from seven test wells distributed throughout the surface-mineable area of the Athabasca Oil Sands have been evaluated to determine the amounts of heavy minerals present and the titanium and zirconium contents. The samples were treated to yield the size distribution of the titanium and zirconium minerals as well as their spatial distribution. The study has shown that heavy minerals are found throughout the surface-mineable area; concentrations range from 0.24 to 2.29 per cent (by weight), with a mean of 1.02 per cent. Titanium and zirconium contents vary throughout the area, and are found preferentially in the finer size fractions. •on the basis of preliminary calculations, the tailings streams from an oil sands plant would provide sufficient feed for a large-scale titanium pigment plant, and the tailings from one plant would provide sufficient zircon feed to satisfy Canadian demand for. metallic zirconium. Variability of the heavy mineral content and composition is such that the heavy mineral potential must be evaluated in detail for each mine site."

Jan 1, 1976

By Godofredo Murillo P

"El objetivo del trabajo es señalar la aplicación del método de sostenimiento a través de los ""pernos de madera"" en las minas de Colquijirca, Cerro de Pasco. La ejecución de este método fue a raíz de la lectura de una de las publicaciones que edita el American Institute of Mining and Metallurgical Engineer, titulada Mining Engineering. Posteriormente se elaboraron varias pruebas, encontrándose en está ultima, un rajo de 18 metros por 6 metros, levantado un promedio de 2 metros y medio, y en el que se colocan los pernos de modo perpendicular a la inclinación del manto, llenando todo el rajo y acomodándose en el rombo. Asimismo se demostró que la fabricación de ""pernos de madera"", cuñas y cabezales en un tiempo de cuatro horas, es mucho mayor que las colocadas regularmente con un ayudante. Por último, se resalta que la eficacia de este método responde al factor de que la roca floja es sementada dentro de un bloque sólido, que es suspendido por los lazos del cable de acero en los huecos perforados en un zona sólida, dando mayor seguridad a los trabajos de sostenimiento en los rajos, asi como facilidad en sus instalaciones."

Jul 20, 1955

By O. Celep, H. Deveci, Ersin Y. Yazici, F. Ahlatci

"There are increasingly stricter environmental regulations imposed for use of cyanide leaching for the extraction of gold from ores. Alternative lixiviants to cyanide, preferably with low toxicity, have been extensively studied. Thiosulphate has emerged as one of the most suitable alternative leaching agent in place of cyanide due to its low toxicity and technical attributes e.g. fast leaching kinetics, high gold extractions from carbonaceous ores in particular. High solubility of most copper minerals in cyanide solutions results in low gold extractions due to excessively high consumption of cyanide. In contrast, low reactivity of copper minerals in thiosulphate solutions makes thiosulphate leaching potentially suitable alternative for treatment Cu-bearing gold ores. The extraction of gold/silver from a copper-bearing pyritic gold concentrate (62 g/t Au, 110 g/t Ag and 0.3% Cu) in thiosulphate solutions was investigated in this study. The concentrate is composed of predominantly quartz (25%) and pyrite (32.7%) as well as sphalerite (5.37%), galena (2.12%) and anglesite (1.13%). Other minor minerals are arsenopyrite, chalcopyrite, covellite and bournonite. Previous studies by the authors indicated that the concentrate did not respond well to cyanide leaching (i.e. 45-46% Au/Ag at 1 g/L NaCN). The effects of concentration of ammonia (0.2-1.5 M NH3), thiosulphate (0.1-0.75 M S2O3) and copper (0-20 mM CuSO4) on the extraction of gold and silver over 8 h. was investigated. Increasing the concentration of thiosulphate and ammonia substantially improved the rate and extent of gold leaching while high copper levels produced an adverse effect particularly at low concentration of thiosulphate (i.e. 0.1 M). Complete extraction of gold was achieved under suitable conditions. In contrast to gold, silver extractions remained consistently at low levels (i.e. 28%). These findings demonstrated that thiosulphate leaching could be used to achieve acceptable levels of gold extraction from the copper-bearing pyritic gold concentrate."

Jan 1, 2018

By Amilton Barbosa Botelho Junior

A busca por metais para atender demandas crescentes vem em contracorrente à diminuição dos teores nas reservas. Desta forma, a busca por novas rotas de extração de metais aliada ao desenvolvimento sustentável se faz cada vez mais necessário. O presente trabalho teve por objetivo a recuperação de cobre do lixiviado proveniente de rejeito de níquel laterítico, que contém os seguintes metais: alumínio, cobalto, cromo, cobre, ferro, magnésio, manganês, níquel e zinco. Para isto, utilizou-se o processo de troca-iônica com a resina quelante Lewatit TP 207, uma resina catiônica com grupo funcional iminodiacetato. Estudou-se o tempo de reação e a influência de pH. O tempo de reação foi variado entre 0 e 24 horas e o pH de 0.5 a 2. Não foi estudado maiores valores de pH, pois haveria precipitação do ferro. A reação de adsorção pela resina entrou em equilíbrio em 180min. Em pH 2 teve maior recuperação de cobre, pois havia menor competição entre H+ e os cátions metálicos do licor, onde foi possível recuperar 50% do cobre. Os ensaios ocorreram em batelada com agitação de 200rpm, e as análises foram feitas usando a técnica de fluorescência de raios X por energia dispersiva (EDX).

Oct 30, 2017

By Charles Hudson Martins de Vasconcelos, Isaque Alan de Brito Moura, Mônica Aline Magalhães Gurgel, Tatiane Santos Ferreira, Andersan dos Santos Paula

Aços bifásicos ou Dual Phase são caracterizados por uma microestrutura ferrítico- martensítica, a qual consiste em uma matriz de ferrita equiaxial com 10 a 20% de martensita dispersa na forma de ilhas. Neste trabalho, utilizaram-se amostras de aço baixo C, micro adição de Nb e Mo, na condição laminada a frio (BFH). As simulações físicas nesse material, em escala laboratorial, foram conduzidas com o objetivo de avaliar a evolução microestrutural após redução de espessura através de laminação a frio e recozimento intercrítico com temperatura de encharque de 800 °C e permanência por 180 segundos na temperatura máxima, seguido de resfriamento sob duas proposições: em água (criticar a fração de austenita formado no encharque em função do potencial para recristalização da ferrita) e ao ar (inferir na formação de ferrita epitaxial e subsequentes transformações bainítica e/ou martensítica no decurso do resfriamento). Utilizando o auxílio da microscopia eletrônica de varredura (MEV), observaram-se que para obtenção da microestrutura característica de um aço DP seria necessário o ajuste dos parâmetros de recozimento em função do percentual de redução na laminação a frio, ou seja, aumentando o percentual de redução do material é necessária a diminuição da temperatura ou do tempo de encharque para que sejam obtidos resultados adequados as características de um aço DP.

Oct 26, 2019

By Frank Tapia, Aldo Gutiérrez

El presente tiene el objetivo de mostrar las principales actividades que se realizan en la estabilización de taludes a doble banco en Sociedad Minera Cerro Verde SAA (Cerro Verde), con el fin de asegurar condiciones seguras y favorables en las operaciones mineras y trabajos en interacción con los taludes de mina.

Sep 30, 2022

By Mário César Mantovani

Um dos principais problemas enfrentados pelas aciarias é o descarte dos resíduos gerados durante a produção do aço. Além de se pagar pelo descarte em aterros monitorados, ocorre também a perda de elementos de liga, tais como Cr, Ni, Mo, V, etc. O objetivo deste trabalho é estudar a viabilidade de se aglomerar alguns resíduos gerados durante a produção do aço (lama de VOD/VD, poeira de forno panela e carepa de forjaria) na forma de pelotas autorredutoras e adiciona-las ao forno elétrico a arco (FEA). Primeiramente os resíduos foram misturados com finos de coque de petróleo e cimento. Após a pelotização e o período de cura, as pelotas autorredutoras foram fundidas num forno de indução (teste laboratorial), visando avaliar o nível de recuperação dos elementos de liga a partir dos resíduos. O rendimento dos elementos Cr, Ni e Mo variaram de 84% a 99% nos teste laboratoriais. Nos testes industriais envolvendo as pelotas autorredutoras de carepa de forjaria (aço ferramenta H13), os rendimentos dos elementos Cr, Mo e V variaram de 51%-92%, 94%-99% e 27,5%-88%, respectivamente.

Jul 30, 2018

By R. E. Jones

"Crusher sizing and application in mining operations is the selection of a crusher or a series of crushers to reduce run of mine ore to a size suitable for either autogenous or conventional grinding. It is important that the crusher or crushers be sized to operate within the range to which they have been designed. By the range to which they have been designed, we mean that the reduction ration must be held between specified limits. Reduction ration is the relationship between feed size to product size.In todays plants reduction is usually accomplished in three stages by primary, secondary and tertiary crushers.Primary crushers are either jaw or gyratory and are designed to handle run of mine feed at an open side setting of 5-1/2” to 7”. Reduction ration should not exceed 7 to 1.Jaw CrushersThe model size of a jaw crusher signifies the feed opening. A model 60 x48 jaw has a feed opening 60” wide by 48” long. The 48” is the dimension between the top of the swing jaw and the top of the stationary jaw. The 60” is the width between the two side frames. The crusher open side setting is the discharge opening at the bottom of the crushing chamber with the jaws in an open position. When corrugated jaw plates are used, the open side setting is measured from tip of one jaw plate to the valley of the opposite jaw plate. If a jaw crusher has a 6” open side setting with a 1” jaw motion, you could also say it has a 5” closed side setting."

Jan 1, 1974

By Juan Pablo Cedillo, Ernesto Feijoo

Se efectuó un análisis y simulación para la explotación de un placer aluvial, su forma y su delimitación por periodos, para la extracción del mineral (oro) con beneficios económicos constantes. Para ello, se empleó una malla regular de exploración y se obtuvo muestras de diversos estratos del placer, a diferentes profundidades. Los resultados de la simulación delimitan las zonas de explotación por periodos, los mismos que varían según la matriz de iteraciones para el ingreso de los valores en el software SimSched. Así, según estos periodos, se puede conocer la cantidad de material que se debe extraer para obtener una ganancia constante durante la vida útil de la mina.

May 22, 2019

By R. R. Lowery

The Bureau of Mines developed hypereutectic aluminum-silicon alloys which 11.7.d better mechanical properties than the unmodified hypereutectic alloy. A commercial aluminum-20 weight-percent silicon LIr alloy was selected as a ary base for improvement. The primary silicon. grains were reduced from ASTM 4-5 to ASTM 8.5 by the use of phosphorus and phosphorus compounds. The remaining eutectic matrix was refined by sodium metal additions of 0.2 weight-percent. Solid solution strengthening of the alpha aluminum was obtained by adding 2 percent copper and 0.5 percent magnesium. Also, 1 percent nickel was added to harden the alloy. Optimum thermal treatment consisted of a solution treatment for 10 hour:, at 480° C with hot water quench, followed by aging for 6 hours at 175° C. The final alloy exhibited a Rockwell B hardness of 75 ±2 in the heat-treated condition. The ultimate tensile strength was 39,5O0 psi with no recordable elongation. The coefficient of linear thermal expansion was 20.4 x 10-6 per °C in the temperature range 20° to 300° C. No wear resistance data were collected.

Jan 1, 1966

By E. V. Lilford

The South African Minerals Development Act (?the Act?) has been promulgated and will come into full force and effect once it is gazetted. Thereafter, all Old Order mineral rights will have to be converted into New Order mineral rights within a 5-year period, probably by the end of 2008. The conversion of rights will be achieved only with the demonstrated inclusion of empowerment groups in the conversion applications. In addition to the Act, the first draft of the proposed Royalty Bill (?the Bill?) was released during the week beginning 17 March 2003. Comments on the Bill?s contents had to be submitted before 30 April 2003. The contents were to be considered in terms of applicability and acceptability to the South African minerals industry, where after proposed comments and suggested amendments were to be submitted to the relevant State Treasury office. Specifically referring to the Bill, the general response from the industry is one of concern. Since any royalty is tantamount to a tax, the general feeling is that the current mining taxation rates are already internationally competitive and to increase these effective rates, notably at differing rates depending on commodity type, will have an adverse impact on the South African mining industry. A number of these impacts can be mitigated to some degree, depending on the flexibility of the State to address the major concerns.

Jan 1, 2003

PROF RICHARD ÅKERMAN Stockholm, Sweden PROF RICHARD BECK Friberg, Germany ANDREW CARNEGIR New York, N.Y. DR. JAMES DOUGLAS New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England PROF HANS HOFFER Leoben, Austria PROF HENRI LOUIS LE CHATELIER Paris France M FLORIS OSMOND Paris, France ALEXANDRE POURCEL Paris, France DR. ROSSITER W. RAYMOND New York, N.Y. PROF ROBERT W. RICHARDS Boston Mass. DR. ING H. C. EMIL SCHROEDTER Dusseldorf, Germany JOHN E. STEAD Middlesborugh, England JAMES M. SWANK (Associate) Philadelphia, Pa. PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia PROF TSUNASHIRO WADA Tokyo, Japan CHARLES D WALCOT Washingtion D.C.

Jan 1, 1917

By C. H. Bucknam

Classical acid-base accounting using modified Sobek titration methods has resulted in interpretation of results for materials with neutralization potential (NP) less than 20 tons of CaCO3/1000 tons of material (2% CaCO3) as "uncertain" due to lack of sensitivity within that content range. Standardization of a "fizzless" acid neutralization potential (ANP) method was undertaken in the American Society for Testing and Materials (ASTM) International using two ranges of sulfuric acid additions based on reaction pH and carbonate carbon estimates rather than subjective fizz testing as well as hydrogen peroxide additions to correct for mineral acidity. The method is identified as the acid neutralization potential acidity (ANPA) titration method. During interlaboratory testing a positive bias was discovered within the "uncertain" range which was further investigated and resolved by increasing the test sample weight from one to five grams for samples needing improved accuracy in materials with ANP <2% CaCO3. Test results from the interlaboratory testing of the low range method is presented and compared with the results from the original ANPA method in the paper.

Feb 27, 2013

By Fred Horne

1N THIS PAPER, the writer proposes to limit his comments to few generalized phases of the subject, based on his personal experience in the midwestern United &apos;States and in one section .of the Coal Branch in Western Alberta. The following statistics are submitted to show the importance that strip mining has assumed in the coal mining industry of the United States. In 1914, 1,281,000 tons of strip coal were produced, amounting to 0.3 per cent of the total production. In 1948, the total was 13~,505,000 tons, representing 23.3 per cent. In 1949, the percentage figure dropped slightly and this can be partially accounted for by the labour disturbances prevalent throughout the year. In 1914, there were 48 power shovels and draglines being used in the stripping of coal; in 1949 there were 3,712, not to mention other types of coal stripping equipment such as bulldozers, tractors and scrapers, rotary excavators, and stackers. At the bituminous coal mines in Western Canada, strip mining was introduced only a few years ago, two of the major reasons for its development being the need for increased production during the war and post-war years and the need to hold the line on increasing production costs, but even in these few years the percentage of strip production has in-creased to such an extent that some mines that, five or six years ago, were producing all their tonnage from underground operations are today obtaining up to 80 per cent of their total output from strip mines.

Jan 1, 1951

By Benjamin W. Haynes

This research was conducted as part of the U.S. Department of the Interior, Bureau of Mines program to recover metals, glass, and a combustible fraction from municipal solid waste (MSW). The objective of this analytical study was to determine the concentration of antimony, arsenic, and mercury in samples taken from various sampling areas in the Bureau of Mines raw refuse recycling plant and to compare these values with those for coals used in the generation of electricity. To provide the necessary analytical data, sensitive reproducible ashing-chemical digestion-atomic absorption procedures were adapted from published procedures. It was determined that antimony and mercury concentrations in the combustible fraction of MSW are approximately an order of magnitude higher than those found in coals presently used for power generation;&apos; the arsenic concentration is similar in both fuels.

Jan 1, 1978

By T C. Westerfield, G, M J. Mankosa

An innovative separator known as the HydroFloat cell has been developed specifically for the upgrading of coarse particles that are difficult to recover using conventional flotation cells. The novel characteristic of this separator is the formation of a hindered teeter-bed of fluidised solids into which small air bubbles are injected. The air bubbles selectively attach to hydrophobic particles and form particle/bubble agglomerates that segregate atop the teeter-bed due to their lower apparent specific gravity. The low-density agglomerates are eventually carried into the product overflow launder by the rising current of teeter water. Hydrophilic particles remain in the teeter-bed and are discharged to underflow as a high solids content tailing. Benefits of this hybrid flotation-density separator include enhanced bubble-particle contacting, increased particle residence time, and very low air demand. Test data indicate that significant improvements in the recovery of coarse particles can be achieved using this innovative technology. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent pilot-scale tests conducted for the phosphate industry.

Jan 1, 2005

By Louis C. Brichta

The Capital Mine is one of, the more important zinc mines in Lawrence County, Mo. Owing to the urgent need for additional zinc during the war and the available facilities for the treatment of zinc-lead ores at the property, the Bureau of Mines examined the mine during July and August 1942 and selected it for further investigation by churn drilling, which was accomplished in the fall of 1943 and spring of 1944. At the conclusion of the drilling on the Capital holdings, the Greenland property, immediately south, was investigated by drilling two additional holes. Results of the investigation are presented in this report.

Jan 1, 1948

By R. S. Warfield

The Kasna Creek copper deposit near Lake Kontrashibuna in the Lake Clark region, Alaska, was the object of an investigative project by the Bureau of Mines during the fall of 1948. Recessed because of inclement weather, it was completed in 1949. This project was a part of the Bureau of Mines program in Alaska for the development of critical and strategic minerals. The ore bodies are contact-replacement deposits in limestone. Mineralization is mainly specular and micaceous hematite associated with chalcopyrite, calcite, chlorite, quartz, and amphibole. The deposit, on the right limit of Kasna Creek approximately 2 miles from the shore of Lake Kontrashibuna, is composed of two mineralized zones that range in altitude from 2,350 to 2,650 feet. This report contains a brief history of the prospect, description of the physical setting of the property, its geology, and the factual results of the Work performed by the Bureau of Mines.

Jan 1, 1951