Search Documents

By S. L. Ausmus

The work covered in this report is a continuation of an earlier feasibility study by the Federal Bureau of Mines and points out improvements in the skull-melting method for casting reactive metals such as titanium, zirconium, and hafnium. Machined graphite molds with laminated sections can be reused many times. Large tube sections can be produced by spin casting. Graphite powder is the best expendable mold material, but binders for this use must be compounded carefully. The effects of current and furnace atmosphere on the dependent variables of the casting technique are shown. Because of developments in casting technology for titanium which eliminate the basic problems of melting and pouring the metal, opportunities for improvement in the method have increased. The mold material and gate and riser configurations require particular attention. The limits of application of the casting method have yet to be defined. New knowledge in anyone of these areas could result in marked improvements and simplifications in casting methods.

Jan 1, 1960

By M. Kuyumcu

After German reunification the mining industry in former East Germany was profoundly restructured. Beside privatization of profitable companies the public sector took over responsibility for the mining operations to be shut down. Therefore state-owned companies cope with technical, ecological, and social challenges. The rehabilitation and reclamation has to rededicate former mining areas to new use and provided new jobs as well. In the lignite mining districts there are around 100,000 ha of mining area, a mining caused disturbance to the groundwater balance and to the system of surface water bodies of approx. 390,000 ha. They are called the largest landscape construction site in Europe. In addition to the results and diverse experience achieved over the past 23 years, a description will follow of our new challenges and of an outlook on remaining tasks. This article will describe the financing, as well as aspects of the jobcreation policy arising from lignite industry remediation.

Aug 1, 2013

Keeping an eye on the future while honoring the past, Frank McAllister, chief executive officer of Stillwater Mining Co., and life member of the National Mining Hall of Fame and Museum, gave the keynote address to a packed house during the 23rd National Mining Hall of Fame and Museum Banquet in Leadville, CO on Sept. 11. McAllister?s company made news just days before the induction ceremony, when it was announced that Stillwater Mining would acquire Marathon PGM Corp. for $118 million (ME, Oct. page 14).

Jan 1, 2010

By J. W. Paul

This circular is one of a series of reports on coal mining methods and cost s which are being prepared by the U. S. Bureau of Mines for the purpose of making available to those interested in the industry a knowledge of the mining methods employed in mines where mechanical and hand loading is practiced and the cost data on the several operations pertaining to the removal of coal from the working faces and its transportation to the tipple for loading into railroad cars. The methods employed are influenced by the natural local conditions with respect to the thickness and character of the coal beds and the overlying strata, the means employed for roof support and its control, and the disadvantages incident to the development of mines in thin coal beds.

Jan 1, 1929

By E. H. Denny

Colorado coal-mine fatalities, which have gradually decreased since 1914, have shown a marked decline since 1924. Data on coal-mine fatalities in Colorado published by the U. S. Bureau of Mines5 indicate that the deaths per thousand 300-day workers have decreased from 9.13 in 114 to 6.14 in 1926, and that the deaths per million tons produced have decreased from 9.18 in 1914 to 4.98 in 1926. Table 1 gives fatality rates in Colorado and in the United States from 1914 to 1926 inclusive. [ ]

Jan 1, 1929

By John B. Gayle

A new, experimental coke oven was installed at the Southern Experiment Station, Tuscaloosa, Ala., in 1948. This oven, designated as the Tuscaloosa oven, features a 17-inch carbonizing chamber, globar heating elements, and silica-brick heating walls designed to simulate as closely as possible carbonizing conditions in commercial, slat-type coke ovens. Zoned heat-input arrangements maintain uniform temperatures over approximately 95 percent of the total flue area. The reasons for constructing an oven of this size, the details of the design, and the operating characteristics of the oven were given in an earlier publication.2/ This report presents the results obtained from the first series of carbonizing tests on Alabama coals with the new oven. Factors leading to the development of standardized operating and testing procedures and the results of crosscheck determinations with a commercial oven producing foundry coke are included also.

Jan 1, 1954

By Aníbal Gatañaga Coll

Dada la peligrosidad del sílice libre como principal problema en el campo de la higiene industrial, el objetivo del trabajo es controlar y evaluar la concentración de dichos polvos a través del uso de tres métodos: El método químico, el de difracción de rayos X y el petrográfico. El primero (N. A. Talvitie), utiliza un reactivo que descompone y disuelve a todos los constituyentes de la muestra, excepto al cuarzo, quedando calcinado y filtrado; el segundo método es eficaz, pero requiere de un equipo muy costoso, mientras que el método petrográfico muestra una mejor identificación de los minerales, determinando las cualidades de los materiales que se producen en la composición del polvo, así como precisa la pequeñez de las partículas encontradas en los polvos industriales y sobre todo de la capacidad del operador.

Jul 20, 1955

By Brian W. Mackenzie

The paper addresses five questions concerning the economic of gold exploration in the western Canadian shield. Can historical footprints be used to project future gold prices for exploration planning? Experience suggests that gold price forecast are too clo ely tied to current market events to provide meaningful guidelines. What range of breakeven gold price will typically be required to ju tify gold exploration in Canada? Minimum price requirements. initially asses ed at $540 to $1080 per ounce, probably lie in the range of $480 to $760 per ounce (expressed in 1985 Canadian dollar). Within Canada, what role do regional conditions and taxation policies play in determining the viability of prospective gold exploration targets? Striking interprovincial differences are found to exist, given the same geological circum tance -Nova Scotia, ew Brunswick, and Quebec rank towards the top in term of motivating exploration, Briti h Columbia provides the least investment incentive, while Saskatchewan and Manitoba place around the middle of the Canadian league. How can minimum acceptable tonnage-grade conditions for gold targets in the western shield be established and, then, constructively applied to provide exploration planning guidelines? Minimum target conditions, realis tically defined in terms of a broad band of doubt, can be used judiciously to help balance the direct costs of uneconomic exploration with the opportunity costs associated with rejecting economic deposits. How does the average cost per ounce of gold discovered in the western shield compare with the overall Canadian experience? Average discovery costs for the we tern shield, apprai ed at $100 per ounce, are shown to compare favourably with the Canada-wide record.

Jan 1, 1986

By Albert L. Toenges

The production of coal from underground mines in Washington declined during the recent war owing to shortage of manpower, and coal was shipped to the Pacific Northwest from mines in the Rocky Mountain region. The movement of this coal into Washington required the use of railroad equipment that otherwise could have been used for transporting war materiel and personnel. Strip mining uses a minimum of manpower, and the development of coal areas in the Pacific Northwest that can be mined by the strip method should increase production in the area, thus releasing railroad equipment from the necessity of transporting coal long distances and also providing consumers with a lower-cost product. The development of a strip mine to supply the demand at low cost requires a large investment in heavy equipment. In order that the fixed charges due to large investment in plant and equipment may be kept at a minimum, large reserves of coal must be proved. A reconnaissance of an area near Toledo, Lewis County, Wash., indicated a large bed of lignite that could be mined by strip methods. The area is approximately midway between Portland, Oreg., and Tacoma, Wash. (refer to fig. 1), and the opening of a large mine in the area would supply fuel to these and other nearby centers.

Jan 1, 1947

By G. Song, S. Yang

"SynopsisThe development of techniques and equipment for single-pass high-seam longwall mining in China is reviewed. Some methods used to obtain the fractured zone height are discussed. The boundary between the caved and fractured zones is generally not clear, but one important difference that distinguishes the two zones is that horizontal compressional forces exist only between blocks of fractured zone. Based on this, a theoretical method is presented to investigate the destabilizing modes of the main roof (by sliding or rotation) and is used to determine if the main roof is in the caved or fractured zone. This method considers the mining height, immediate roof thickness, bulking factor, main roof thickness, main roof strength, main roof periodic weighting interval, and vertical stress in the overlying strata. To verify the method, a representative physical model of Wangzhuang coal mine is developed. The movement of overlying strata and fractured zone height are thus obtained. According to the results, the total collapsed height of the strata reaches about 70 m above the coal floor; the first main roof bending interval is 45 m and periodic bending distance is 10–15 m; the maximum strata subsidence is around 62 mm; and the presence of a three-hinged arch causes the fluctuation of subsidence in the same stratum level. Based on the theoretical and experimental analysis, the middle of the main roof is considered the boundary between caved and fractured zone; the caved and fractured zone heights are about 21 and 49 m respectively.IntroductionThick coal seams (>3.5 m) account for about 44% of the coal rescource/reserves and more than 40% of the total annual production in China (Zhao 2004; Wang 2009). Three mining methods – slice mining, top coal caving, and single-pass high-seam longwall mining – are frequently used in underground thick-seam operations. Compared with slice mining and top coal caving, high-seam single-pass longwall mining significantly simplifies the mining processes, reduces roadway excavation, and improves coal production, productivity, and recovery. The favourable economics, high production, and technical simplicity make high-seam single-pass longwall mining one of the most popular underground mining methods for thick coal seams in China."

Jan 1, 2015

By Faisal Shalzad, Adnan Anwar Malik, Tadashi Maejima, Jiro Kuwano

Single helix screw piles carry most of the structural load through end-bearing if the helix is embedded in the dense bearing layer. The tip condition of the central shaft of the screw pile can be closed, closed with cutting blades, opened with flat cut, and opened with wedge shape cut and its selection is based on the insitu ground conditions. These different end conditions of the central shaft disturb the ground differently, leading to the change in bearing capacity. In this study, an attempt is made to investigate the effect of open and close-end screw piles on installation effort (installation load and torque) and bearing performance in the dense bearing layer. The model steel screw pile with a pile shaft diameter of 21.7 mm and helix diameter of 43 mm is used in this study. Test results show that the open-end screw pile required less installation effort than the close-end pile that penetrated the bearing layer by 1Dhwith an unplugged condition. Further, the open-end screw pile shows a higher bearing response than the close-end screw pile if it enters the bearing layer with an unplugged condition.

Oct 1, 2022

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

By Estéfano Aparecido Vieira

O presente trabalho busca desenvolver métodos de estudo de remoção de inclusões de aço em escala de laboratório relacionando propriedades como viscosidade e composição química das escórias com a capacidade de remoção de inclusões. Com esse fim, foram desenvolvidas cinco escórias usando como referência a viscosidade da fase líquida assim como o percentual da fase líquida. As escórias foram adicionadas sobre o aço fundido e comparou-se o nível de inclusões antes e depois dos experimentos. As escórias também foram analisadas após os experimentos através da difratometria de raios-x para identificação das fazes formadas. Os resultados apontam que as escórias testadas possuem a capacidade de remover inclusões. Porém escórias com elevado teor de CaO tem maior eficiência na remoção das inclusões.

Oct 30, 2017

By A. M. Gaudin

Jan 1, 1962

By Paul H. Johnson

The CH Leaching process is a new, more sophisticated, form of gold, silver, uranium and sulfide copper heap leaching wherein each layer of a multi-layered heap is divided into a number of independent cells, each of which are successively formed and leached in the top layer of the heap to their maximum economic recoveries, and then rinsed and sealed from further leaching. Triangular earth berms form the outside walls of the heap and a gridwork of rock-filled berms on top of the bottom pad form independent under- heap solution storage zones. The high degree of solution recirculation and staging that occurs in this process produces a relatively small volume of very rich pregnant solution. The cellular heap design and its mode of operation result in a uniform, intensive, long-term leach for all of the ore particles in the heap. Besides improved metal recoveries, the process appears to have several cost and operating advantages. In the CR2MR process, sulfuric acid and a soluble sulfide are added to a gold and/or silver pregnant leach liquor to precipitate most of the contained silver, mercury, copper, etc. as sulfides at a pH below 2.5. The other product of the reaction is solubilized HCN. Following a liquid-solid separation step, cyanide is regenerated in the supernatant solution by raising the pH to a level above 9.0. This process regenerates a portion of the cyanide used in the leaching step, removes contaminant ion species (silver, copper, mercury, etc.) from the leach solution and, in a subsequent step, recovers the gold in an enriched form. It is believed that substantial cost savings may be experienced by the use of this process in some gold and/or silver leach systems.

Jan 1, 1984

By Theodore von Rosenvinge

Large diameter (2.4 meter) drilled shaft foundations were installed to depths of over 62 meters through soil into Arkose bedrock for Connecticut?s Pearl Harbor Memorial Bridge (I-95 over New Haven Harbor). The project involved many ?firsts? including the first ?extradosed? cable-stayed bridge in the US, and for Connecticut, the deepest drilled shafts, the first use of a rotator to install shaft casing, and the first use of the Mini-Sid technology for rock socket bottom inspection. Design utilized both friction and end bearing for rock sockets. O-Cell testing was employed to maximize performance factors during design and to allow adjustments to socket lengths during construction. Favorable test results permitted a reduction in socket lengths and significant cost saving.

Jan 1, 2011

By Osvaldo Bascu

La falta de integración entre la información de las minas y las plantas metalúrgicas es un problema para las empresas mineras. Por ello, para incrementar las estrategias de mejoramiento continuo y Six Sigma se requiere información en tiempo real de los activos, camiones, palas, equipos de planta, estanques, inventarios y transacciones. En ese sentiido, el presente texto señala el uso de las nuevas tecnologías a través de las redes inalámbricas y el Internet en la administración de los complejos metalúrgicos. Además, se destaca la importancia del uso de los datos en tiempo real para aumentar la disponibilidad de los activos en la mina y plantas metalúrgicas al integrarlos con los sistemas de manutención tradicionales.

Sep 19, 2006

By Jeffrey Meissner, Mike Waldron, Charles Dowding

Most studies of crack response have focused on opening and closing of a crack in the plane of the wall in which the crack occurs. Crack movement also occurs perpendicular or normal to the plane of the wall. This paper will examine and compare the in-plane and out-of-plane (normal) response of cracks in two different residences near limestone quarries. In two locations, sensors that measure in-plane and normal displacement were installed side-by-side on the same crack, allowing direct comparison of the two modes of response. In a third location, a perpendicular pair of displacement sensors was installed in a corner of a room to observe the bidirectional response of the structure at a corner. Both long-term and dynamic data were recorded with the same sensors; temperature, humidity, and air over pressures were also recorded to compare blast and weather effects. Measurements show that ratios of out of plane to in plane response to dynamic events can vary. However, the ratios of out of plane (normal) response to vibratory events to that of climatological change is still as small as the ratio for in plane crack responses.

Jan 1, 2010

By Luis Villegas

El presente texto señala el método del relleno en pasta como elemento clave en la explotación en la mina Iscaycruz. El relleno en pasta se basa en el empleo de relaves, cemento, agua y un químico floculante, donde son dosificados y mezclados en una planta y son transportados por una línea de tuberías hacia los niveles de mina. Entre las ventajas que se presenta está la eficiencia en los trabajos de relleno, así como da una mayor vida a los depósitos de relave, minimiza el uso de equipos en la operación y reduce costos operativos. Asimismo permite obtener en los tajos rellenados características homogéneas y otorga mayor dinamismo al sistema de relleno.

Sep 12, 2005

By Norman P. Goss

What would appear to be a very simple process on paper has proved to be overrun with a multitude of unseen difficulties. For more than 70 years attempts have been made to cast metals in a continuous manner, but it has been only within the last Io years that some degree of success has been achieved.1 Historical Development Bessemer's Experiments—Method I Bessemer was the first to try to cast molten metal in a continuous manner. His method is fully described in U. S. Patent No. 49053, issued in 1865. The patent drawing is shown in Fig. I. In this method the molten metal was poured between a pair of rolls of large diameter, which were cooled by water sprays. Means were provided to prevent moisture from coming into direct coptact with the molten metal. The width of the strip was controlled by the flanges. On paper this should work to perfection, but it is beset with many difficulties still awaiting solution. Bessemer failed to reduce his invention to commercial practice. About 1890 Bessemer's method was revived by Norton and associates (U. S. Patent No. 441375). They formed the Fluid Metal Rolling Co. at Maywood, Ill., and spent $250,000 in endeavoring to develop the technique for this simple method. Finally they had to abandon it. Naturally, they did carry the technical development far beyond anything Bessemer had done, but even so it was far from being a useful commercial success. In recent years it has undergone further development by C. W. Hazelett (U. S. Patent No. 2058447), who has succeeded in obtaining long lengths of copper, brass, aluminum, and even stainless steel. He introduced many' ingenious devices but the greatest obstacle still remained—the disintegration of the roll surface when the surface is heated and chilled in rapid succession. Difficulty is also experienced in maintaining a uniform supply of molten metal to the rolls. The patents pertaining to this method would indicate these to be the major obstacles. Experimental work by Mellen—Method 2 A departure from the method introduced by Bessemer, was tried by Grenville Mellen, of East Orange, K. J., sometime between 1914 and 1920, who obtained a number of patents.2 His method is illustrated in Fig. 2. This method failed to make an impression upon the art; however, it is of value in pointing out the difficulties the inventor ran into and the way in which he tried to meet them. The split mold sections form two endless chains. When going through the center of the apparatus, these sections engage each other to form a complete mold. As the engaged mold section moves downward at a constant speed, molten metal is teemed into it. As this is going on, another set of cooperating mold sections move into position on top of the one being filled. The molten metal is teemed into the mold through a silica tube. According to the teachings of this patent, the level of molten

Jan 1, 1945