Search Documents

By V. Nasri, S. Rashidi

The Baltimore Red Line Project is a proposed 22.7-km (14.1-mile) long east-west light rail transit (LRT) line envisioned to connect the areas of Woodlawn, Edmondson Village, West Baltimore, downtown Baltimore, Inner Harbor East, Fells Point, Canton and the Johns Hopkins Bayview Medical Center Campus. The Red Line LRT System has two tunnel segments - the Cooks Lane Tunnel (CLT) and the Downtown Tunnel (DTT). The CLT segment is roughly 1,920-m (6,300-ft) long. It commences at the west portal located at the highway ramp for I 70 (to be removed) and terminates at the east portal that is at the intersection of Edmondson Avenue (U.S. Route 40) and Glen Allen Drive. This segment of the project consists of the following construction components: approximately 1,458 m (4,786 ft) of tunnels, 143 m (469 ft) of cut-and-cover tunnel, and 318 m (1,045 ft) of retained cut (U) section. The approximate horizontal alignment for the Red Line LRT Project is shown in Fig. 1.

Jan 1, 2014

By Yongping Wu

The steeply dipping coal seams in this paper refer to those with the angle of inclination ranging from 35° to 55°. The reserves of the steep coal seams account for approximately 15%~20% of the total coal reserves in China. In the past 12 years, the top-coal caving mining method had been used to mine the steeply dipping thick (11.5-16.4 ft or 3.5-5.0m) coal seams. However, the mining process of top coal caving is complex with low recovery rate and nearly 30% of coal was wasted. Those problems can be solved by using the single pass large mining height (11.5-16.4 ft or 3.5-5.0m) method. But the movement of the overlying strata around the mining face area of large mining height is complex and it is hard to control the stability of ?rock-shield support? system. Therefore, field measurement, numerical simulation and physical (similarity material) simulation methods were used simultaneously to analyze the strata movement, roof structure and rock-shield support interaction characteristics. The results indicate that strata movement, which is the same as mining the steeply dipping seams with conventional mining heights, is asymmetrical about the dipping direction of the face; deformation, failures, and movement of the surrounding rocks are more intense; the roof weighting interval decreases; the weighting intensity increases significantly; and face sloughage occurs frequently. In the gob, the space for sliding and rolling of the roof increases; the broken main roof tends to form an anti-dip pile structure; the backfilling and compactness of broken roof increase at the lower portion of the face, thereby inducing significant unbalance in stress distribution between the upper and lower portions of the face. The overlying strata above the face form a multi-level step structure. The characteristics of contact and loading of roof-shield support system are more complex. The range of shield load variation is larger, and interaction between shield supports occurs frequently. Anti-toppling and anti-sliding devices at the face become more difficult to implement. The research results provide a theoretical basis for the mining practices in the steeply dipping thick seams with a large mining height. The practice in panel 25221 of 2130 coal mine indicates that the accident rates have been greatly reduced and good technical and economic benefits have bee realized.

Jan 1, 2014

By Colin Lindsay

"The Collahuasi copper mine, located at an altitude of 4300 meters above sea level in northern Chile, commenced operations late in 1998. The mine is currently the 4‘h largest copper producer in the world and comprises an open pit, a 60,000 tpd sulphide concentrator, a 15,000 tpd oxide heap leach and SWEW plant and a 200 km concentrate pipeline to a port facility.Constructing, commissioning and operating a mine at high altitude presents unique challenges in terms of the performance of both equipment and people. It is important that these be recognized and carefully considered during the feasibility study and the detailed design stages and the success of the Collahuasi project is largely due to this. The plant design incorporates a number of features aimed at mitigating the problems of altitude and the construction methodology also took into account the particular site conditions.This paper discusses the Collahuasi project team’s approach to planning for the remote location and also some of the problems experienced during construction, commissioning and operation.INTRODUCTIONThe Collahuasi mine is located in northern Chile, some 250 km to the south-east of the port of Iquique and 15 km from the Bolivian border. The mine facilities lie between 3800-4300 m above sea level on the Altiplano, the central plateau of the Andes mountains, and cover a total of approximately 95,000 hectares. Although the area is arid, it experiences an average of 150 mm of precipitation annually and weather conditions can be extreme. Temperatures during the day range between -3 to +11 º C and are generally below 0ºC at night, sometimes as low as -20°C. High energy winds are common and humidity is low. Much of the precipitation occurs during the winter as snow but there also occurs a period during the Chilean summer known as the “Invierno Boliviano’’ (or Bolivian Winter) which is characterized by severe electrical storms and rain."

Jan 1, 2001

By V Novoselov, R Sabirov

Flotation processing technology of water-soluble minerals has made it possible to realise, since the 1960s, the wide scale industrial processing of potash and potassium-magnesium ores (about 200 million tonnes per year) as well as to create the multi-tonnage worldwide production of sylvite (KCl) for industrial and agricultural application. In this paper the particularities of the effect of reagents (blinders, collectors and frothers) during cation flotation in saturated saline solutions are outlined. New reagent modes for activating the effects of alkylamines during the flotation of KCl and the perfecting of technological flow sheets for processing potassium ore have been developed. The results of research on the reverse flotation of carnallite ore, with the help of alkylmorpholine û a new developing technology for benefication carnallite as raw material for the production of metal magnesium and fertilisers are listed. Examples are given of the industrial applications of processed reagent modes at potash flotation factories in Russia.

Jan 1, 2005

By J. Howard Bird

The purpose of this publication is to describe the power-distribution system of the mine and refinery of the Duval Sulphur & Potash Company at Carlsbad, N. Mex. This distribution system has been excellently predesigned to meet requirements and fit special conditions encountered at the property. In presenting the material, the authors point out various features that would be desirable for incorporation in other systems under similar conditions. Central location of switchgear in pressurized vaults and ventilation of such equipment with filtered air prevent salt accumulations and contribute to trouble-free operation. The simplification of power-distribution circuits and overload protection, as a result of centralization of switchgear, the use of individual control circuits enclosed in conduit (which aids troubleshooting), and central location of control panels, are factors which contribute to efficient, safe operation. Those features are applicable to many operations where fire or explosion hazards are encountered, or where dusty conditions may exist, as well as in operations where numerous individual drives are involved.

Jan 1, 1959

By Nelly Carmen Rivera Oliva

El presente texto describe el sistema de catastros de pasivos ambientales, el cual permite recopilar la información de acuerdo a criterios técnicos, a través de los datos más relevantes de las unidades mineras inactivas y de su entorno. Su diseño está basado en la toma de datos mediante dos planillas digitales denominadas: la ficha de identificación y caracterización de pasivos ambientales mineros que incluye el registro de la información del medio físico, biológicos, social y la ficha de identificación y caracterización de componentes mineros abandonados para el registro de datos específicos de caracterización de los aspectos físicos de la operación minera, los que se subdividen en cinco categorías definidas como: labores mineras, residuos mineros, residuos no mineros, edificaciones e infraestructura, y sustancias químicas. Ambas fichas registran el ingreso de información de aspectos jurídicos, físicos, ambientales para una adecuada caracterización. Finalmente, la recopilación se realiza en tres etapas: precampo, campo y postcampo o gabinete por medio del registro a través de diversos controles de introducción de datos.

Jul 1, 2014

By K. Duckworth

The treatment of Turam data by conventional procedures does not permit the interpreter to make any estimate of induced current magnitudes. This problem may be overcome by using an alternative data treatment procedure. It is shown that the conventional and alternative procedures are equally satisfactory in terms of their ability to provide the location of line currents and estimates of conductor quality. A full description and evaluation of both procedures is presented in conjunction with field examples to show how the alternative procedure may assist interpretation when used to complement the conventional approach.

Jan 1, 1973

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years ago were only laboratory curiosities.

Jan 1, 1941

By Sean Gallagher, Thomas G. Bobick, William S. Marras

Twelve healthy, experienced underground cool miners performed lifting capacity tests in stooped and kneeling postures using a modified psychophysical procedure. Subjects adjusted weight in a lifting box to the maximum they could handle without undue fatigue in an asymmetric lifting task. Lifting periods were 20 min in duration and the frequency was 10 lifts/min. Tests were performed under a 48-in. roof that restricted the subject&apos;s posture. Psychophysical. physiological, and biomechanical dependent measures included the maximum acceptable weight of lift (MAWL), heart rate (HR), rate of oxygen consumption (VO2), ventilation volume rate (VF), respiratory exchange ratio (R), and integrated electromyography (EMG) of eight trunk muscles. Results indicated that the MAWL was significantly lower when kneeling than when stooped (p < 0.05), Furthermore, metabolic demands were greater in terms of HR (p < 0.005) mid VO2 (p < 0.05) when kneeling. Left and tight erectores spinae muscles exhibited increased EMG activity- in the kneeling posture (p < 0.001). It was concluded that psychophysical lifting capacity is decreased, while the metabolic stress and internal load on the spine are increased, in the kneeling posture. Results of this Bureau of Mines study indicate that it may be advisable to reduce the weight of materials that are handled repetitively in the kneeling posture.

By Norman King

El texto aborda la importancia de las relaciones positivas con los sindicatos en América Latina a través de dos conceptos: las relaciones de poder y las relaciones humanas. Por ello, es necesaria la aplicación de las relaciones humanas que pueden existir en las negociaciones con los sindicatos. En este sentido, se evalúan los elementos que influyen en su esctructura como la negociación-fuerza, el conflicto; el acomodamiento; la cooperación y las ideologías. De otro lado, las relaciones humanas permiten comprender las difcultades de negociación y política que implican tanto la relación de los sindicatos como de la administración y así mejorar el problema económico y de preparación de los dirigentes sindicales.

Aug 20, 1963

By Mauro Vivaldino Fernandes

Os desafios para o aprimoramento do desempenho operacional dos altos-fornos constituem um campo aberto para o desenvolvimento e aplicação de métodos de controle que promovam a otimização da operação do reator, aliada ao prolongamento da sua vida útil. O Alto-Forno 3 da Usiminas - Ipatinga, nesta sua 4ª campanha, foi projetado para 15 anos de operação, com uma produção estimada de 41 milhões de toneladas de gusa. Os resultados da campanha atual, em termos de produção e de duração da campanha, superam os dados projetados. Neste contexto, são apresentadas as principais características do Alto-Forno 3 na sua atual campanha, a evolução do seu desempenho em termos de produtividade e tempo de operação, além das principais ações direcionadas para a preservação e estabilidade do sistema de refrigeração e do cadinho, contribuindo para o prolongamento da sua vida útil. Como resultado destes esforços, a vida útil estimada do Alto-Forno 3 é de 22 anos, superando em 7 anos a duração prevista.

Oct 30, 2017

By P. G. Larén

El presente trabajo describe algunos sistemas específicos que pueden ser usados en la minería subterránea. En este sentido, se revisa el sistema de perforación hidráulica en la técnica de perforación de rocas duras, como las ventajas de su aplicación. Para ello, el tema de perforación se divide en tres temas: perforación hidráulica, voladura lisa y perforación productiva en corte y relleno, cámara y pilares. Asimismo se realiza una comparación entre la perforación vertical y horizontal del uso de taladros en rebajes de corte y relleno. Finalmente, se refiere la importancia de la existencia de jumbos de alta capacidad en la influencia de métodos de cámaras y pilares.

Nov 20, 1978

By Julio Aníbal Morales Pereira

Sabe-se dos problemas associados com as inclusões não metálicas, os quais afetam não somente a operação de fabricação, como também a qualidade do produto final. Por esses motivos, muitos estudos têm sido realizados para melhorar o controle do tamanho, quantidade, forma, distribuição e composição das inclusões. Especificamente para as inclusões de espinélio MgO·Al2O3, ainda é preciso melhorar o entendimento dos fenômenos sobre a formação e modificação destas inclusões para um melhor controle ao longo do processo de fabricação do aço e obter maior limpidez inclusionária nos aços. Assim, neste trabalho, foram revisados tópicos reportados na literatura relacionados com: a formação, influência da composição da escória e modificação com cálcio das inclusões de espinélio.

Aug 16, 2017

By Lix Tafur, Julio Gómez, Vidal Aramburú

Las operaciones de la pequeña minería artesanal de oro se caracterizan por tener bajas recuperaciones, bajo condiciones inseguras de trabajo y consecuencias negativas en el ecosistema por el uso indiscriminado del mercurio y/o cianuro, Con la finalidad de mejorar dicha práctica se desarrollaron pruebas de lixiviación con reactivos alternativos al cianuro para recuperar oro y plata a partir de los relaves de amalgama. El análisis mineralógico determinó la presencia de especies como: oro, pirita, magnetita, hematita, Ilmenita, rutilo y gangas, así mismo los ensayos químicos determinaron una ley de 20.16 g-Au/TM, 147.12 g-Ag/TM y 10.53 ppm de Hg

Sep 29, 2023

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years a ago were only laboratory curiosities.

Jan 1, 1941

By Mark Cross, Andrew P. Campbell, Koulis A. Pericleous

"Computational Fluid Dynamics (CFD) modelling is being used to simulate the freeze layers formed within direct smelting processes. There has been some concern whether water-cooled elements can withstand the p~ocess conditions and in particular abnormal cases where they may be splashed in molten metal.To validate the models being developed, two cases from literature have been modelled for solidification and stress analysis. The solidification case is presented in detail and is for hot molten metal flowing through a cylindrical pipe. The walls are at a temperature below the melting point for the metal. The resulting solid (or freeze) layer is within 3% of the value calculated by Sampson & Gibson9 •Preliminary modelling of the refractory-slag interactions is presented. Although three basic mechanisms: Penetration; Corrosion; and Erosion will eventually be modelled, only the penetration is considered here. The corrosion mechanism is to be modelled by tracking the time that the penetrated refractory is at the required temperature.Future work, after adding all the required physics, will focus on the modelling of a water-cooled element placed lower in the smelter. Process perturbations will be simulated to examine what these elements will withstand."

Jan 1, 2001

By David Vergara Segura

Una empresa minera, en condiciones normales, maximiza su operación y minimiza sus pérdidas por tener operativos y equipos ligados a la producción. Por lo que es necesario la integración entre las áreas de la empresa, específicamente entre las de Mantenimiento y Logística. En este sentido, el presente texto señala la importancia del trabajo en equipo entre estas dos áreas, cuyo objetivo común es optimizar la gestión del activo que tiene un impacto significativo y directo en la producción. También se plantea bajo del esquema de una empresa minera ficticia, el desarrollo de estrategias conjuntas, y se define un modelo de gestión logístico, generador de ventaja competitiva, el cual está orientado a la optimización del uso del activo.

Sep 12, 2005

By Ricardo Gaviria, Vincinte Acosta

There are major blast design and field procedures differences between conventional blasting in horizontally bedded coal seams and blasting underneath coal seams in a multi seam deposit with seam inclinations of 14 degrees or more.

Jan 1, 1995

By Alexis Cotrado

Shahuindo, es un yacimiento único en su género, se encuentra en un prolífico cinturón que produce oro en el norte de Perú, a 30 km al norte de la Unidad Minera La Arena. La operación es un tajo abierto usando operaciones convencionales de perforación/voladura, carguío y acarreo. El método de minado es a tajo abierto con un movimiento promedio de 87,500 TPD de roca y 36,000 TPD de Mineral. El presente trabajo muestra un ejercicio de optimización de las reservas minables comparando el valor del proceso chancado & aglomerado (C&A) y el proceso ROM, usando técnicas de optimización de la ley de corte para agregar valor al proyecto y cumplir con las restricciones operativas de Mina y Lixiviación.

Sep 29, 2023

By T Huynh, K Tungpalan, E Wightman, M Edraki, S Palaniandy

Most preventive environmental management practices promote proactive integrated approaches to waste management. For example, life cycle assessment is often used to find the ‘hot spots’ of environmental burdens. This kind of approach is often based on generic data and has rarely been used for tailings. Besides, life cycle assessments are less useful for designing operations or simulating changes in the process and consequent environmental outcomes. It is evident that an integrated approach for tailings research linked to better processing options is needed.The aim of this Nextmine™ project is to develop new tailings management models by streamlining orebody characterisation, process optimisation and rehabilitation. We present an integrated tailings management approach and preliminary results from a case study. Combined grinding and flotation models were developed using geometallurgical data from the orebody, to predict the properties of tailings produced under various processing conditions. The modelling scenarios based on the case study data provide the capacity to predict the composition of tailings and the resulting environmental management implications. For example, the type and content of clay minerals in tailings will affect the geotechnical stability and water recovery. Clay content will also influence decisions made for paste or thickened tailings and underground backfilling.CITATION:Edraki, M, Huynh, T, Wightman, E, Tungpalan, K and Palaniandy, S, 2015. An integrated approach to proactive tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015