Search Documents

By T. D. Guldem, J. L. Kaae

ALLOYS with nominal composition of 45-Fe 35-Ni 20-Cr, ASTM-B-163, known under the commercial names of Incoloy 800 and Sanicro 31 (Alloy 800), are often employed at elevated temperatures for extended periods. Therefore, knowledge of the aging behavior of these alloys is of considerable importance. Significant decreases in ductility and increases in yield strength have been observed in the 45-Fe 35-Ni 20-Cr alloys containing about 0.4 pct Ti and 0.4 pct A1 after long-term aging at 540" to 700"~."~ However, no direct evidence has been presented for precipitation phenomena that might result in such changes. Strengthening effects have been attributed to the effects of local or-dering.3 Since y' precipitation (Ni3A1, Ti) is known to occur in similar alloys which contain more titanium and aluminum,4-7 it was decided to explore the possibility that y' might precipitate in these alloys and might be responsible for the changes in mechanical properties on aging. This note reports some observations of two distict types of matrix precipitates made by means of transmission electron microscopy, in a 45-Fe 35-Ni 20-Cr alloy containing 0.31 pct Ti and 0.4 pct Al. The steel used in this investigation was obtained from the Sand-vik Steel Works; it is designated Sanicro-31 (Alloy 800). The chemical composition of the alloy is given in Table I. Aging of solution-treated material at 700" and 800°C for 130 and 100 hr, respectively, produced the matrix precipitates shown in Figs. l(a) and l(b). It is apparent from these micrographs that the precipitate particles occurred in the form of thin square plates parallel to the matrix cube planes. Extraction replication and selected-area electron diffraction showed that the precipitates were M23C6. Coherency strains, consistent with the semicoherent nature of small M23C6 precipitates,' were evident for certain imaging conditions. In addition to matrix precipitation, preferential precipitation of M23C6 on dislocations was common, as has been reported previously for austenitic stainless steels.'" Specimens aged for longer times (-300 hr) at 700°C exhibited a different type of coherent matrix precipitate in addition to the M23C6. An example is shown in Figs. 2(a) and 2(b). In addition to the few large M23C6 precipitates, small precipitates exhibiting strain contrastl0,ll are present. The "line of no contrast" of the strain field of a given precipitate lies along differ-

Jan 1, 1970

By Peter Zamora

Dado que ya no es posible confiar en el incremento industrial de las materias primas de las especies minerales y no metálicos de la tierra -en tanto estas son caracterizadas por condiciones minero-geológicas favorables-, el presente texto refiere posibles soluciones a través de yacimientos de grandes profundidades, condiciones desfavorables y de ley más baja que el mineral y así proceder a la explotación de los llamados yacimientos pequeños que hasta ahora han sido registrados y balanceados en el marco de la llamada "riqueza metálica" de tal o cual Estado, pero que no fueron considerados como industrialmente explotables a título de la explotación económica y técnicamente poco efectiva. Asimismo, la explotación de yacimientos minerales pequeños por los métodos clásicos de explotación masiva con utilización de la mecanización minera automóvil libre de carriles y la aplicación de los métodos geotecnológicos, elimina los procedimientos clásicos de afloramiento, trae el elemento de movilidad a los equipos de extracción y de beneficio. De esta forma reduce asimismo los costos de inversión de la explotación y permite así su explotación efectiva.

Sep 1, 1981

By Robert Thurner, Albin Norrman, Sami U. Raja

The West Link is a double track railway project currently under construction in Gothenburg, Sweden. The project includes the construction of 8 kms of track, 6 kms of which will be in tunnels. Beside several large excavations, three new stations will be built: Centralen, Haga and Korsvägen, all within the city of Gothenburg. The first construction phase of the project began in May 2018, and the finalization of the project is expected in 2026. The project is divided into five sections. Keller is involved in four of these contracts since the design & planning phase in 2018 assisting the special foundation works with various geotechnical techniques including Dry deep soil mixing (DDSM), jet grouting, rock grouting, uplift piles, sheet piling and rock dowels. The core idea behind successful collaboration has been to apply the right product for a location specific challenge which can help optimise costs & time for the project with a minimal environmental impact. Due to the extensive nature of the project, a team of experts from various locations around the world is helping design and execute various foundation technologies and providing solutions to the practical challenges in the project like working close to existing structures, rail lines, river etc.

May 1, 2022

By J. E. Chilton

A technique for use in underground coal mines measures the response times of machine-mounted methane monitors. This technique uses a calibration cup to deliver gas to the sensor head to measure response times. For comparison, in the current study, response times were measured by placing methane sensor heads in a specially designed test box where they were exposed to an atmosphere containing a constant concentration of methane. Response time readings measured in the test box were shorter than the readings obtained using the calibration cup. The response times measured in the test box were comparable for sensors from three different manufacturers. The effects of dust cap and flame arrestor design on response times were also evaluated using the test box.

By Miguel Ángel Zuñiga C

El presente texto describe la simulación económica y financiera como propuesta de inversión en un proyecto minero a través de una estructura financiera que comprende 80% de financiamiento y 20% de aporte de los accionistas. De acuerdo a ello, la inversión está programada a realizarse en cuatro años, cuyo precio inicial es de 300 millones de dólares y que verá incrementada por la tasa de inflación del país donde se efectúa dicha inversión, y por la de los países donde va a comprarse los materiales y el equipo.

Nov 20, 1978

By A. Bruynesteyn

The results of leaching experiments in columns simulating 80 and 200 ft deep cores through a leach dump are discussed, By equipping the columns with can precipitation plants, actual plant conditions could be duplicated. The results produced a better understanding of the physical and chemical limitations of the leaching process.

Jan 1, 1975

By D. G. Purdy

Planning, as defined in Webster's New Collegiate Dictionary, is a detailed program of action designed to achieve an end. When developing a detailed plan to incorporate all the complex activities involved in a surface lignite mine, many elements must be carefully evaluated as to the individual and cumulative effects on the end result. The following elements are generally evaluated when planning a surface lignite mine: ? Reserve evaluation, including lignite quality characterization; ? Delineation of mining parameters, including lignite recovery factors, geotechnical factors, land control factors; ? Selection of mining blocks; ? Pit sequencing; ? Reclamation, including soil reconstruction design and land use planning; ? Overburden handling design; ? Selection of equipment; ? Sizing of equipment; ? Manpower requirements; and ? Other elements, including contract negotiations and execution, financing, investment return, operation economics, permitting and scheduling.

Jan 1, 1985

By Finley A. Campbell

"Nickel-copper sulphide deposits associated with basic rocks in the Quill Greek area and the White River area in the Yukon Territory have been studied and compared from the view-point of their general geology, structural geology, and the mineralogy of the ores. The relative amounts of the major constituents, magnesium, iron and calcium, and the minor constituents, nickel, cobalt and chromium have been determined spectrographically for two cross sections of the basic rocks at Quill Creek and one at White River. These data, along with petrologic and field evidence, were used to determine the sill and dyke-like character and nature of the basic intrusions. Loss on ignition is employed as a measure of the degree of serpentinization. The distribution determined shows that the serpentinization does not appear to have greatly influenced the inferred original distribution and lithophile associations of magnesium and nickel. The cobalt content may have been altered.The nickel content of the serpentinized peridotites ranges from an average of 0.36 per cent in one section to an average of 0.24 per cent in each of the other two sections studied. The cobalt averages 0.0038 per cent in the samples from the two Quill Creek sections and averages 0.0042 per cent at White River. These results have been compared with other available data.The sulphide ores are later than both the peridotite and gabbroic rocks and may be co-magmatic with them. There is no evidence in these areas to support an origin by lateral secretion; on the contrary, the alteration associated with the ores, the mineralogy and spatial relationship to basic and ultrabasic rocks, indicate the ores are derived from a basic magma."

Jan 1, 1960

By John Bradford

El presente texto describe la geología, historia, geografía del yacimiento epitermal de oro denominado Poracota. Dicho yacimiento es un sistema epitermal de alta sulfuración que está ubicado a 160 km al NW de Arequipa y se hospeda en el Arco Volcánico continental calco-alcalino del Sur del Perú, del Oligoceno superior al reciente. Asimismo, se encuentra en una importante franja de mineralización epitermal de metales preciosos del Mioceno, que incluye las minas de oro-plata de Orcopampa, Arcata, Shila, Cailloma y Sukuitambo, la mina de plata-metales comunes de Madrigal y los recientes descubrimientos de Ares y Chipmo. La zona aurífera está en la zona de silicificación intensa, es sílice cavernosa (vuggy) y en cuarzo-alunita sobrepuesta por pirita. La zona de cuarzo-alunita envuelve a la zona aurífera silicificada y la alteración decrece hacia afuera a dickita, caolinita, illita, clorita y calcita.

Apr 26, 1999

By John W. Trammell

The White Pine Mine is situated in Ontonagon County, approximately six miles south of Lake Superior, in the Upper Peninsula of Michigan (Figs. 1 and 2). The ore body mined by White Pine Copper Company occurs in the lower - most 20 to 25 feet of the Nonesuch formation, a series of middle - to upper Keweenawan shales, siltstones, and sandstones. This paper elaborates on the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the ore body.

Jan 1, 1964

By Lorenz E. Sieffert, Lawrence B. Berger, H. H. Sehrenk, Ralph W. Stewar, James A. Gale

"INTRODUCTION The purpose of the investigation discussed in this article was to evaluate the toxic hazard from gases produced when thermosetting plastic materials used for electrical insulating purposes are burned or thermally decomposed in enclosed spaces. For brevity the term ""toxicity"" is used throughout the article to refer to the nature of gases produced under these conditions. A need for immediate study of the problem was created as a re¬sult of the battle damage reports received from various United States Fleet units. These indicated that the fumes emitted when these materials were burned or thermally decomposed had, in several instances, resulted in toxic atmospheres. In attempting to develop a suitable test method for evaluating toxicity, it was recognized that no single test procedure could be expected to duplicate the variety of conditions that might exist in an actual fire aboard ship. In view of the immediate need, however, it was felt that considerable information could be obtained, at least to classify comparatively the several types of materials as to the toxic effect caused by burning or thermal decomposition, through the development of a sound empirical method which could be applied to all of the materials. On this basis, it was decided to modify the Navy flame resistance test for thermosetting plastics to render it applicable to the determination of the toxic, gases evolved when this test was employed. A wide variety of materials was tested, both molded and laminated, to cover the types commonly used by the Navy in electrical applications. Toxicity determinations were conducted at the Bureau of Mines Central Experiment Station, Pittsburgh, Pa. Parallel tests, to determine the flame resistance of the materials, were conducted at the Material Laboratory, U. S. Navy Yard, New York, N. Y."

Oct 1, 1947

By Thomas C. Poulter

Abstract The Poulter seismic method of geophysical exploration is an attempt to obtain an increased efficiency in the conversion of the energy of an m~pl06ion into useful energy which has directive properties and which contains a minimum of random frequency and random phase relations. Very little effort has been made in the past to simplify OT even control the uniformity of the seismic energy being introduced into the ground. The Poulter seismic method is also an attempt to improve the signal-to-noise ratio not merely by trying to complete the impartial filtering done by the earth on ,the continuous spectrum of primarily high-frequency energy radiated from a shot point but by applying a frequency control at the point of origin of the seismic wave. The energy from a shot-hole charge is peaked in a frequency which is much higher than will be transmitted through the ground, and its absorption introduces background interference. Only 10 to 20 per cent of the seismic energy of a shot-hole charge .is directed downward in a 90-degree vertical cone, whereas, from a pattern of charges detonated above the surface of the ground, 85 per cent of the seismic energy is included in a 90-degree cone and in some cases it is even confined to as small as a 30-degree cone. This greatly reduces the horizontally distributed energy, thereby producing a marked improvement in the signal-to-noise ratio. The frequency of the signal energy may be peaked in a rather narrow range by the proper application of two or more impulses upon the surface of the ground controlled as to direction, magnitude, and timing. These impulses may be controlled by the reflection shock wave technique, the pressure pulse technique, and the sequence firing technique, using the primary controls as outlined. The information obtained from the study of directivity of seismic energy in a high velocity, uniform material such as the ice on Taku glacier, in the Juneau ice field in Alaska, has been of great assistance in the application of the method to oilfield and mining problems.

Jan 1, 1950

By P. N. H. Bhakta, X. P. V. Lei

The U.S. Bureau of Mines developed an alkaline oxidative pretreatment to increase the recovery of gold from refractory sulfide ores containing arsenopyrite (FeAsS) and/or pyrite (FeS2). Pretreatment of a low grade ore containing 0.4% FeAsS, 3.5% FeS2, and 2.74g/mt Au with 1.2m NaOH, 40 psig o2, 100° C, and 4 hr in a 2-L autoclave resulted in 94 to 96% sulfide oxidation. cyanidation of the pretreated residue resulted in 88% Au extraction compared to <20% Au extraction for untreated ore. Cyanide consumption was 0.25 kg NaCN per metric ton of ore. A flowsheet for treating sulfidic low-grade gold ore is proposed.

Jan 1, 1990

By S. Holtermann

Through the process of Riverbank Filtration (RBF), the Louisville Water Company plans to obtain a higher quality source of water for their B.E. Payne Water Treatment Plant (WTP) by means of four collector wells located in the alluvial aquifer along the bank of the Ohio River. The collector wells are connected to a 2,850 L/s (65 mgd) pumping station by a 2,362 m (7,750 ft) long, 3 m (10 ft) finished diameter tunnel located in limestone and shale bedrock, which is approximately 45 m (150 ft) below the surface. High tunnel boring machine (TBM) production rates were achieved in this moderately weak bedrock; most of the tunnel only required support in the crown. An unanticipated water-bearing fault and unanticipated ground behavior proved challenging and required quick thinking to minimize impacts to construction. Tunneling conditions are discussed in detail, together with the methods used for overcoming the groundwater and ground behavior challenges. The tunnel is expected to be completed in April 2009.

By Adolfo Valvano

Cerro Vanguardia S.A. (C.V.S.A.) es uno de los yacimientos auríferos y argentíferos más significativos y de mayor trayectoria de Argentina. En ese sentido, el presente trabajo describe las acciones desarrolladas por la compañía minera Cerro Vanguardia en referencia a la responsabilidad empresarial, y su relación con el desarrollo económico, la responsabilidad social y el cuidado del medio ambiente en las comunidades cercanas donde opera dicho yacimiento. Asimismo, se describen ejemplos y experiencias impulsadas por la nueva actividad como es la minería metalífera, que permitió recuperar una economía regional, la cual vivía una realidad desalentadora, producto de los bajos precios internacionales de lana y las bajas productividades de los campos por la intensa desertificación producida por malos manejos y la erupción del volcán Hudson en el año 1991, que cubrió de cenizas gran parte de la Meseta Central Patagónica.

Sep 12, 2011

By Gabriel Prosofsky de Araujo

O compósito carbono-epóxi é um material altamente resistente à tração. Porém, as fibras comprimidas durante a flexão não resistem à flambagem. Dessa forma, faz-se necessário um estudo mais detalhado. Este trabalho consiste em verificar quais propriedades mecânicas dependem exclusivamente da orientação das malhas das fibras. Corpos de prova de orientação 0°/90° e 0°/90°/±45° foram processados e ensaiados em flexão de três pontos, de acordo com as normas ASTM E855 e D790, em uma máquina universal de ensaio MTS – Material Test System com capacidade de 250 kN. Inicialmente, os tecidos sofreram o tratamento superficial da silanização, promovendo a futura adesão das fibras na resina. Após a silanização, as lâminas foram montadas e impregnadas com a resina epóxi. A cura da resina do compósito foi obtida em uma estufa Fanem modelo 320°C a 120°C por uma hora, subsequentemente os corpos de prova foram obtidos utilizando-se o corte à jato d’água. Concluiu-se que as falhas de todos os corpos de prova foram devido à tração. Corpos de prova com volumes de vazios internos apresentaram menores valores de rigidez e aqueles com mecanismos de fratura como flambagem e delaminação apresentaram valores de resistência menores.

Aug 7, 2018

By H. P. Holmes

Tonnage quantities of hafnium metal have been prepared in Kroll-process equipment designed for producing zirconium. Some slight process modifications have been necessary, but overall operation is the same as for zirconium. Hafnium oxide is chlorinated in the presence of carbon and the resultant hafnium tetrachloride reduced by magnesium metal. Byproduct magnesium chloride is removed in a high-vacuum distillation step and the hafnium sponge metal crushed for further use. Arc-melted metal can be forged and rolled to sheet, but the best material produced to date would not be considered cold ductile. INTRODUCTION This investigation is part of the program for the production of pure metals from domestic and foreign ores that has been underway at the Bureau of Mines for several years. It was done in cooperation with the Atomic Energy Commission and the Bureau of Ships.

Jan 1, 1955

By David R. Hargis

Large-scale groundwater withdrawals are necessary to depressurize a confined aquifer system allowing the dry open-pit mining of the overlying phosphate ore. The extent of the existing and planned groundwater development led to the establishment by the State of North Carolina of Capacity Use Area No. l. Groundwater use in the Capacity Use Area is regulated by a permitting system. A two-dimensional finite-difference ground- water flow model was developed for North Carolina Phosphate Corporation. The aim of the model is to aid the Corporation in matters relating to permitting by serving as a predictive tool. The model can be used to project regional water level impacts resulting from various scenarios of depressurization pumping.

Jan 1, 1983

A glance at the accompanying table reveals that for the first time in many years the industrial minerals field did not post significant gains in production. Gypsum, cement, sand and gravel, and crushed stone production-which are very sensitive to construction industry performance-barely managed to stay even, or in fact, declined slightly. Even barite production, in spite of increased oil and gas drilling, was off 5% in 1979 from 1978. Domestic fluorspar production continued to decline while imports, primarily from Mexico, South Africa, and Spain, rose 11%. Worldwide production of iodine (which is used primarily as a catalyst, animal feed additive, and in ink and colorants, stabilizers, pharmaceuticals, photographic film, and disinfectants) grew about 9% on a worldwide basis-from 10.75 Tg to 11.16 Tg. This does not include US production. The two US producers increased demand as apparent domestic production increased about 5%. Increasing energy costs and the transportation situation have had a prohibitive effect on the industrial minerals field. The critical shortage of railroad cars, according to consultant Neil Johnson, is due to several factors: • High capital investment rind interest rates needed to build new equipment, • Accidents, obsolescence, and failure to repair equipment reduced car availability, •Reduction in some train schedules due to fuel economy, and •Increased turnaround time as a result of new safety regulations. Railroad rates have increased an average of 7% per year for the past 10 years. Last year&apos;s increases were about 11.1% due to fuel costs and surcharges. Truck shipments have increased their penetration in certain areas of the southeast because of the shortage of box cars and the producers&apos; demand for quick shipment. Some producers report a 15-20% increase in truck use. In the feldspar-mica area, which formerly made most shipments by rail, trucks are now used for about half the shipments. Marketing prices, as expected, increased due to higher costs for energy, power, labor, and supplies used in production. Estimated average price increases were about 10% which, in many cases, did not cover increased production costs. These factors-rising energy costs and the critical transportation situation-resulted in an unsatisfactory year for industrial minerals. Stanley J. Lefond Cnntrihuting Editor

Jan 5, 1980

By T Hicks

Designers of mining facilities play a significant role in defining the overall mine greenhouse gas emissions performance. This demands an appreciation of all the greenhouse gas emissions sources, including Scope 3 emissions, which will form an increasing fraction of the emissions as we transition our generation sources to renewable energy. Traditionally overland conveyors are designed to operate as fast as practical, and through this approach, achieve relative minimisation of: conveyor belt tensions; belt width; mechanical equipment masses; structural steel quantities; and concrete quantities. It is well understood that higher belt speeds reduce capital cost and improve project economics. Operating at higher speeds introduces operating costs through system energy losses and increased wear rates. This paper assesses the life cycle greenhouse gas emissions for a typical iron ore overland conveyor to demonstrate how the design criteria and engineering decisions impact greenhouse gas emissions and project economics. An analysis of the decarbonisation potential and project economics using a range of operational parameters has been completed, developing a marginal abatement cost for each system configuration, creating a basis for integration of low emission overland conveyor designs as part of the broader facility decarbonisation strategy.

Sep 1, 2024