Search Documents

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2(Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ?phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By Charles E. Dandois

New is a relative term, and, when used with reference to a concept as old as shaft kilns can be applied to a number of designs. In this case the design that is the subject of this paper, is known as the ring or annular shaft kiln as developed by Mr. Karl Beckenbach of West Germany. The first&apos; operating unit was rated 185 tons per day and was installed in 1962. Today, there are approximately 84 units in operation in Western Europe and Japan. Twenty-one additional units are in the process of erection or on order. Developed sizes range from approximately 100 to 330 tons per day. Units of over 500 tons are in the design stage, however, the largest units presently operating are rated 330 tons per day, <the first: of this size having been installed in 1966. "Figure" 1 is an elevation view of the unit. It is a single vertical cylinder to which are attached the required service platforms, combustion chambers, injectors and distribution piping. Auxiliaries such as recuperator, exhaust fan and dust collector are mounted on the appropriate service platform. The charging pan, feed conveyor, etc. are mounted at the kiln top. At the bottom of the kiln is the silo with a vibrator type discharger, and mounted separately is the required blower for injector air and fan for internal cooling.

Jan 1, 1973

By Derek H. C. Wilton, David T. W. Evans

"Abstract - The Midas Pond gold prospect, central Newfoundland, is hosted by sheared and altered felsic and mafic pyroclastic rocks of the Tulks Hill volcanics, Victoria Lake Group, and has been trenched and tested by 19 diamond-drill holes. Gold values are sporadic, with the best diamond-drill intersection assaying 7.3 g/t over 0.9 m, and the highest grade channel sample containing 14.7 g/t over 1.15 m. Alteration and mineralization are confined to a 200 m wide brittle-ductile shear zone. This shear zone formed in response to regional D1 deformation, and the shear zone fabric parallels the regional S1 foliation. D2 deformation resulted in broad Z-shaped flexuring of the shear zone. The deformation was probably related to the ca. 396 Ma to 420 Ma Salinic Orogeny.Advanced argillic alteration and an extensive halo of Fe-carbonate and pyrite surround the gold mineralization. Alteration minerals include pyrophyllite, paragonite, quartz, plagioclase, chlorite, fluorite, Fe-carbonate, and pyrite. As such, the alteration seems to reflect combined epithermal (argillic) and mesothermal (carbonate) mineralizing environments. The argillic alteration and fluorite represent a regional hydrothermal effect on the felsic volcanic rocks; whereas, the Fe-carbonate and pyrite represent a mesothermal alteration associated with auriferous quartz veins. The Au, which is spatially associated with pyrite, occurs in three structurally-controlled vein sets. These veins are confined to the contact between a highly deformed breccia (the banded mafic tuff) and structurally overlying, altered felsic tuffaceous rocks. The vein sets include: V1 boudinage veins that parallel the shear-zone fabric (C-shear veins), and V2 and V3 extensional fracture veins which are controlled by an S2 fracture cleavage. V1 veins are the earliest and contain the lowest concentrations of Au. V2 and V3 veins are concentrated within the hinges of the D2 flexures.Pb isotope data for galena separates indicate that the Pb in the vein systems was probably of local derivation. Sulfur, C, and O isotope data for mineral separates are similar to data for typical mesothermal lode gold deposits. Fluid inclusion data suggest the presence of at least three hydrothermal fluid types in the region, viz., (1) an early saline fluid which produced the argillic alteration, (2) a CO2-bearing fluid directly related to the auriferous mineralization, and (3) H2O-NaCl fluids which flowed through the Midas Pond shear zone at a lateral distance from the zone of mineralization. The mineralizing fluids are interpreted to have been CO3 -2-rich types which originated through metamorphic dehydration and decarbonation of mixed island-arc and continental crustal rocks. Gold precipitation resulted from the reaction of these fluids with the Fe-rich breccia unit. Pre-existing and simultaneously crystallizing pyrite served as loci for Au precipitation."

Jan 1, 2000

By L. A. Khan

This paper first discusses the physicochemical cleaning methods used to process fines followed by an analysis of the subprocesses of froth flotation and the adverse effects of slimes and particle oxidation. These subprocesses include the phenomena of interception, contact, adhesion and levitation. Preventive and corrective measures to combat the generation of fines and their effects are suggested. Preventive measures include controlled grinding, limited liberation, flotation at coarser sizes. Means of preventing oxidation and/or removing oxidation products are a1 so discussed. Corrective measure to increase recovery include intensive aeration, aggregation of particles, intensive mixing, increased retention time, and reduction of detachment. Measures leading to improves selectivity involve means to reduce slime coating, achieve selective mineralization of bubbles and minimize entrapment.

Jan 1, 1986

By Andre Luis de Zorzi Marin

O corte a plasma de aço inoxidável tem história relativamente nova em comparação com outros meios de corte de metais. Frequentemente os usuários de corte plasma se deparam com questões específicas ao corte do aço inoxidável, como qualidade de corte, velocidade de corte, custo operacional e alterações nas propriedades metalúrgicas. Nos últimos vinte anos as tecnologias aplicadas no corte plasma do aço inoxidável tem evoluído com resultados atrativos nos últimos cinco anos. Estas tecnologias versam com alterações na mistura dos gases de plasma e de proteção, ou ainda, na mudança dos bicos de corte plasma buscando melhor constrição do arco plasma, e a devida seleção de gases em função da espessura de corte. Este trabalho foi desenvolvido através de revisão bibliográfica das principais tecnologias apresentadas pela indústria nas últimas duas décadas para o corte de aço inoxidável com plasma, e testes laboratoriais de corte com as últimas tecnologias de corte. Entre os resultados estão a redução até a eliminação da escória pós-corte, uma borda de corte menos arredondada, melhora na coloração da superfície e diminuição da zona afetada pelo calor na peça de trabalho. A importância do trabalho se dá pelo aumento da participação do uso do aço inoxidável dada a sua importância para a economia, em especial nos setores de energia, processamento de alimentos, papel e celulose e transportes que necessitam de melhorias no corte deste metal e suas ligas.

Jan 16, 2018

By C. W. Jr. Waterman

INTRODUCTION MY SUBJECT is one which would require several speakers and many hours of time for adequate presentation in all its many facets. Because of the widely varying market requirements and coal seams mined, the coal industry of the United States bas of necessity employed many types of preparation facilities to satisfy its needs. Predominance of Baum-type jigs, however, bas marked the mechanical cleaning installations since the early thirties, and these machines continue to hold the lead. CLEANING As a matter of record we find that, at the end of 1948, we had 480 mechanical cleaning plants in operation. Of these, 19 used air cleaners only,?400 used water washers only, . and 61 used dry and wet washers in combination . Due to the increased use of spray water underground on cutting and mechanical mining equipment, there has in recent years been a marked downward trend in dry cleaning installations. In fact, the moisture in dry-cleaned fines has been increased to such an extent by spraying that recent dry cleaning installations have incorporated thermal drying ahead of the dry cleaning units in an effort to overcome the varying and increasingly higher moisture percentages in their raw coal feeds. While on the subject of dry cleaning, it might be well to bring to your attention one of our most recent developments in this art. I refer to the McNally-Brusset vacuum jig.

Jan 1, 1951

By George E. Summers

A salt dome appears to provide the basic medium requirements for the excavation of the 315 foot diameter, unsupported spherical cavity at a depth of 2700 feet required by the AEC in a proposed "decoupling" experiment. Tatum Salt Dome was a natural choice for a site because more geological and hydrological information has been accumulated on Tatum than any other salt dome on the Gulf Coast. The Tatum Dome is a mile in diameter, roughly flat topped, nearly cylindrical in shape and has some overhang at the top. The salt stock has nearly vertical layering of alternating bands of salt and anhydrite. In the vicinity of the dome, adequate fresh water for solution mining is available in surface streams and in subsurface aquifers. A saline aquifer is available for brine disposal. A tentative cavity location was selected near the center of the dome which meets the design criteria established by the AEC.

Jan 1, 1968

By W. W. de Graaf, M. J. Ntsekhe

Klipspruit Colliery is experiencing coal losses, which leads to a negative impact on coal production and subsequently loss in revenue. This study aimed to identify the possible causes of coal losses in the No. 4 upper and lower seams. The objectives were to identify potential sources of coal losses through a literature survey, to identify areas where the coal losses occurred, to determine factors affecting coal losses, and to identify the most cost-effective methods to reduce coal losses. Highwall losses, top-of-coal losses, and coal edge losses were identified as the major areas of coal loss at Klipspruit. These losses were mostly attributed to the drilling and blasting practises of the pre-split, interburden waste, and the coal seams. Recommendations include re-visiting the current pre-split design and the tolerances adopted for the interburden and coal seam drilling and blasting design. It is furthermore recommended that Klipspruit implement a continuous improvement plan for the drilling and blasting and refresher training for the blasting crew and operators.

Jun 10, 2024

By Marcella Mateus de Mello

O presente trabalho objetiva analisar a influência da distribuição de intensidade espacial do laser na geração de padrões de speckle em superfícies metálicas. Os padrões de speckle estudados são obtidos quando o laser atinge uma superfície metálica. A análise da imagem de padrões de speckle pode ser relacionada com a rugosidade de superfícies metálicas iluminadas com o laser. Com esse estudo pretendemos melhorar a sensibilidade das medidas de rugosidade de superfícies metálicas a partir das imagens de padrões de speckle.

Aug 17, 2017

By J Jackson, D C. Curry, A C. Keith

Australian Bureau of Statistics (ABS) data shows that since 2006 the balance of capital costs associated with mine development has become weighted greater than 75 per cent to enabling infrastructure and less than 25 per cent on process plant, equipment and machinery. The well-developed mine planning techniques including pit optimisation and scheduling and process plant design and optimisation have typically proceeded in a linear fashion from geology, mine planning, through processing, with some iterations back to the mine. Only then is attention paid to planning and costing of enabling infrastructure in any detail.Optimisation has typically involved developing cut-off grades, mine plans and schedules and ore processing that produces maximum economic ore. Infrastructure has then been sized æto suitÆ the mining and processing core business drivers.What the ABS data, together with global trends, indicates is that infrastructure can no longer be an afterthought if miners wish to achieve robust project value estimates, realistic ore to market costing and resource statements based on achievable economic cut-off grades.In addition, with such a large proportion of the costs originating from non-mining or processing activities, a mining operation can only be truly optimal if these aspects are given due consideration in the mine design stages, based on quality geometallurgical inputs so that the size and cost of enabling infrastructure is optimised to maximise project value.This paper outlines an iterative holistic approach to mining project development, which integrates the geometallurgical approach and enables infrastructure planning into project design and evaluation. It presents case studies showing reduced overall costs, increased net present value (NPV) and reduced project delivery timelines.CITATION:Curry, D C, Keith, A C and Jackson, J, 2013. Is a 2.5 per cent success rate good enough? Traditional mine development methods have the tail wagging the dog, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 113-128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By T. Shi, Q. Yuan, S. P. Vanka, B. G. Thomas

"The quality of continuous cast steel is greatly affected by fluid flow in the mold region, especially involving transient phenomena. Mathematical models are being applied to investigate many different aspects of these phenomena, but their accuracy must be validated before they can be applied with confidence. As part of a long-term effort to develop and apply comprehensive models of the continuous casting process, this work evaluates the relative accuracy of models of three different fluid flow phenomena in continuous casting through comparison with measurements.Firstly, transient flow simulations of velocities in the mold region are compared with digital particle image velocimetry (PIV) measurements in a single phase water model. Large-eddy simulations (LES) are found to reasonably match the flow measurements, including transient flow variations, except at long time scales, which could not be modeled owing to the excessive computation costs. The standard K-e model produced very good agreement with time-averaged velocities for relatively little computation time, although it is inaccurate at predicting the transient variations. Secondly, particle trajectory calculations are compared with water model measurements to study the distribution and flotation removal of inclusion particles. The LES model was able to match the measurements both qualitatively and quantitatively. Thirdly, steady, multi phase flow computations are compared with flow patterns observed in both a water model and an operating steel caster with argon gas injection. For the same conditions, the water model and steel caster produced very different flow behavior. The computational model was able to match the measured flow patterns in both cases.This work suggests that computational flow modeling has the potential to match real processes as well or better than water models, especially when complex related phenomena such as particle motion and multiphase flow are involved. Much work is still needed to further improve the models and to apply them in parametric studies."

Jan 1, 2001

By Gordon G. Duncan

Historical Sketch Occurrences of native copper have been known along the Arctic coast of Canada, especially in the vicinity of the. Coppermine river, since the early part of the eighteenth century (See map, Figure 2, insert). In 1769, Samuel Hearne, a clerk of the Hudson&apos;s Bay Company at Fort Churchill, was sent to explore the &apos;copper mines&apos; from which natives had been reported to secure copper for tools, fishing spears, etc. After two successful attempts, he reached the Coppermine river in 1771, accompanied by Indian guides. This hazardous trip was indeed a remarkable feat when one considers the vast distance covered, a great deal of which was barren lands. At Bloody falls, (See Figure 1) on the Coppermine river, Hearne&apos;s Indians swooped down on a party of sleeping Esquimaux, who gathered there each summer to fish, and murdered the entire band encamped on that side of the river. Hence the name of the falls. Hearne&apos;s knowledge of minerals was undoubtedly limited. He reported having seen the copper mines from which the natives were securing the copper, but he failed to prove the economic possibilities of the copper occurrences or to give an accurate description of any deposit. Sir John Franklin visited the area in 1821. He and other members of his expedition, namely, Richardson, Back, Kendall, and Hood, reported native-copper float to occur in the vicinity of the Coppermine river and Bathurst inlet.

Jan 1, 1931

By Henry P. Wheeler

Natural gas was first stored underground in Welland, County, Ontario Province, Canada, in 1915.3/ The following year natural gas in the United States was first stored underground successfully in the Zoar field near Buffalo, N, Y. Only three additional storage fields were in use in the United States in 1930, but by 1940 the number had increased to over 30, and since that time growth has been more rapid. At least 80 fields, with a combined storage capacity of 440,828 MM c. f ., were being utilized by 1949.4 / In May 1952, 142 storage projects having a capacity of 915,000 MM c.f. were in operation .5/ These fields are distributed from New York to California--from Michigan to Texas. In the Appalachian region alone, there are 101 storage fields with a combined capacity exceeding 526,000 MM cu. ft. Why Natural Gas is Stored Natural gas is stored in order to be readily available to meet the needs of consumers.

Jan 1, 1952

"AbstractThe Sedimentary Basin area of Western Canada, which lies between the Precambrian Shield and the Cordilleran mountain area, covers approximately 800,000 square miles. Sediments ranging in age from Cambrian to Tertiary are present and, of these, horizons in the Upper and Lower Cretaceous, Jurassic, Mississippian, and Devonian have yielded commercial oil and gas flows. Producing horizons in the Cretaceous and Jurassic are sandstone, while all those of the Palaeozoic are carbonate rocks such as red limestone or dolomite (bioherms). Shows of oil and gas have been encountered also in the Cambrian and Triassic sediments.The broad structural features of this vast expanse of sedimentary rocks are the Moose Jaw syncline, the Sweet Grass-Battle River arch, the Alberta syncline, the Foothills belt, the Rocky and Mackenzie mountains, the Great Bear-Slave Lake basin, and the Mackenzie Delta Basin area.This contribution outlines the .stratigraphy and structure of the Basin area, and gives examples of present producing oilfield structures and stratigraphic traps.Part 1.-Regional StratigraphyIntroductionThe vast expanse of relatively undisturbed sedimentary rocks of western Canada has long been recognized as prospective territory to search for oil and/ or gas. This search in western Canada dates back before the turn of the century, but, considering the size of area to be explored and tested, the effort an<l money expended upon it, which, before the recent discovery of oil at Leduc, Alberta, appeared large and fruitless, now seems almost ridiculously small. A check-up of effort and money expended prior to and since the Leduc discovery would undoubtedly reveal that more wildcatting and development has taken place during the last two and a half years than during all previous years combined. The figures would astound not only the average citizen, but many within the industry itself."

Jan 1, 1950

By D. A. Ainsworth

"The first known use of activated carbon dates back to the Ancient Egyptians who utilized its adsorbent properties for purifying oils and medicinal purposes. Centuries later, the early ocean going vessels stored drinking water in wooden barrels, the inside of which had been charred. (However, by modern definition the carbon used in these applications could not truly be described as activated.) By the early 19th century, both wood and bone charcoal was in large scale use for the decolorization and purification of cane sugar.However, it was not until the beginning of the First World War that the potential of activated carbon was really capitalized upon. The advent of gas warfare necessitated the development of suitable respiratory devices for personnel protection. Granular activated carbon was used to this end as, indeed, it still is today.By the late 1930's there was considerable industrial scale use of carbon for both gaseous and liquid phase application and new manufacturing processes had been developed to satisfy the needs of industry. During the 1939-1945 war, a further significant development took place - the production of more sophisticated chemically impregnated carbon for the removal of both war and nerve gases."

Jan 1, 1984

By Fabiana da Silva Santos

Neste trabalho foram estudados os efeitos da laminação a frio com baixo percentual de redução e a cinética de recristalização em um aço médio carbono e alto manganês. O aço em estudo foi laminado a frio com percentual de redução de 10%, seguido de um tratamento térmico de recozimento nas temperaturas de 650 e 700°C, em tempos de 10, 15, 20, 25 e 30 minutos. A caracterização microestrutural e avaliação da fração recristalizada foram avaliadas por microscopia óptica e a dureza Vickers (avaliada em um macrodurômetro e um microdurômetro). De acordo com os resultados pode-se observar um efeito combinado de recristalização e crescimento de grão em função da microestrutura parcialmente encruada pelo baixo percentual de redução imposto, que se acentua com aumento do tempo e da temperatura de encharque.

Aug 16, 2017

"El presente texto señala las formas en que se presenta el sílice libre y las principales rocas constituyentes del material generador de la silicosis. En ese sentido, el ""sílice libre"" se presenta a través de tres formas: cristalizada, criptocristalina y amoría. Sus diversas variedades en forma de cuarzo son el cristal de roca, el cuarzo amatista, cuarzo rosado, amarillo, ahumado, lechoso, ferruginoso, etc. De otro lado, la presencia del cuarzo en las rocas ígneas sirve de base para su clasificación en ácidas, intermedias, básicas y ultrabásicas. Las rocas ácidas son las que contienen más de 10% de cuarzo, las intermedias menos de 10% de cuarzo y las básicas y ultrabásicas, carecen de este mineral en su esencia. Asimismo para determinar el grado de peligrosidad del polvo es necesario revisar la concentración de partículas de polvo, a través de una muestra y cuenta de los mismos. El muestreo se basa siguiendo diferentes técnicas basadas en principios fiísicos como filtración, estrellamiento, precipitación electrostática y térmica. Mientras que la cuenta de partículas se efectúa mediante un microscopio provisto de un sistema óptico standarizado y diferentes tipos de celdas (Dunn, hemacitómetro y la celda Hatch). Cabe aclarar que no es posible la comparación de peligrosidad de dos polvos, basándonos solo en el componenente sílice, sino que el tamaño de las partículas y la concentración en el ambiente, son factores a considerar para su evaluación. Entre los métodos importantes de determinación cuantitativa de sílice libre tenemos: químicos y físicos. Los primeros, utilizan la descomposición de todos los componentes de la muestra -con excepción del sílice libre-a través de un tratamiento ácido, mientras que los segundos son más precisos respecto de los polvos industriales y se realizan a través de análisis petrográfico, difracción de rayos y el método de fusión. Posteriormente, la Asociación Americana de Higienistas industriales revisa los datos encontrados en África del Sur, Australia, Inglaterra y Estados Unidos, y hace un esbozo sobre los límites de tolerancia permisibles de polvo, revelando que el polvo contenido con más de- 50% de SiO2 es equivalente a 5 MPPPC, los que tienen de 5 a 50% de SiO2 tienen 20 MPPPC, y aquellos que contienen hasta 5% deSiO2 equivale a 50 MPPPC, a diferencia de otros métodos propuestos."

Jul 20, 1957

By Transfert Environment and Society

Transfert?s added value ? Building bridges between project promoters and communities ? Unique expertise in working toward Social License to Operate through meaningful community engagement ? 25 years of recognized innovation and a systematic approach ? Key mining clients: ? Royal Nickel Corporation ? IAMGOLD - Niobec ? Richmont Mines - Wasamac ? Mine Arnaud ? Managem

Aug 1, 2013

The expansion of hydrometallurgical operations, declining ore grades and upwardly spiralling production increases the demand for fresh and recycled water with low levels of contaminants. The minerals industry is also increasingly being forced both by regulatory and cost pressures to reduce the amount of liquid waste they produce. This requires a strong focus on waste reduction by recycling, regeneration and reuse. However, these measures are often not enough in arid countries for a forward progress and expansion of their mining activities. &nbsp; It is often the case that in the arid and semi-arid countries the only available water is either sea water or underground (brackish to hypersaline) saline waters. Brackish waters can be desalted at a reasonable cost but the desalination of highly saline waters is challenging and expensive. &nbsp; There are emerging reports that sea water and in some cases hypersaline underground waters are now used by various mining industries as process water. This study explores the possibility of the use of sea water in various mineral processing and hydrometallurgical processes and briefly discusses the benefits and problems related to the use of saline waters at the mine and mill site. Several cases studies and preliminary laboratory test results are presented.

Jun 1, 2010

By Mohammad R. Jafari

The Camp Dresser & McKee (CDM) has been retained by the Sacramento Regional County Sanitation District (SRCSD) to design the Mather Interceptor, a portion of the South Interceptor and Mather Interceptor program. The Mather Interceptor consists of 14,667 feet of 54 to 72 inch gravity interceptor. Approximately 90 percent of the alignment will be constructed via tunneling. Cobbles and boulders in a sand/gravel matrix dominate the ground conditions combined with seasonal perched groundwater table at some of the deeper reaches of the alignment, impacting design consideration. This paper will present the results of a comprehensive geotechnical investigation conducted for this project and in-depth technical evaluation of various trenchless techniques feasible for tunneling in the cobble and boulder laden formations of this project. This paper will also present the risks and issues of the design alternatives and selection criteria.