Search Documents

By Haukka M. T

A new low-dilution fusion method which has been successfully used for accurate determination of the major oxide components of silicate rocks, is applicable to rapid, accurate determination of trace or minor eiements in mineral exploration samples. Limit of detection is in many cases less than 5 ppm. Either rapid, approximate measurement and calculation methods (suitable for geochemical exploration), or more accurate methods (applicable to orebody evaluation studies) may be used.Rapid methods are described for nickel in rocks and sulphides containing 10 ppm to >2 per cent Ni, and for gallium. The rarely-determined element gallium is an example of a constituent which may be easily investigatedby XRF using the LiB02 fusion disc, which is a permanent, easily-stored analytical sample available for later rapid or accurate analyses. The method is applicable to over 30 elements at levels encountered in mineral exploration.

Jan 1, 1978

By James M. Barker

The borate deposits of Death Valley, first exploited in 1882, were a major world source of boron-bearing products until shortly after very large deposits near Boron, California (Kramer) came on stream in 1926. Borate mining in Death Valley then became moribund, with most extant deposits held as reserves backing Kramer. Tenneco began borate operations following acquisition of claims in 1967 and is the only active borate producer inside Death Valley National Mon¬ument. Borate ores, confined to the lower Furnace Creek Formation (early to middle Pliocene), initially precipitated in a shallow lake fed by boron-rich volcanic hot springs associated with the Basin and Range province. Later diagenesis and remobilization plus regional folding, faulting, and erosion altered and complicated originally simple borate mineralogy and distribution. Dominant ore minerals are ulexite (NaCaB509.8H20), probertite (NaCaB509.5H20), and colemanite (Ca2B6011.5H20). Tenneco currently operates two open pits near Ryan, California. Mining is by bulldozer-pushed scrapers hauling waste and front-end loader/off-highway truck combinations for ore and waste haulage. Archeological, environmental, and aesthetic considerations influence both mine plans. Boraxo Pit, opened in 1970, has deep ore (stripping ratio 10 to 13:1) which occurs along a fault and as beds in shale on the hanging wall. Problems include pit wall instability (adverse bedding), non¬ripable calcareous shale (11,000 fps), and mixed ore separation. Sigma Pit, opened in 1975, has shallow (stripping ratio 1 to 1). low dipping, bedded ore in shale. Massive ulexite and "granular" un- cohesive colemanite present problems in mining and milling. Colemanite is crushed to -6 inches, washed, dried at 350°F, then calcined at 800°F with 100 tpd capacity. Crushed (-6 inch) ulexite or probertite is Raymond milled to customer specifications with a capacity of 1000 tpd.

Jan 1, 1976

By Hendri Silaen, Charles Leatemia, Monang Napitupulu, John Kamarea, Arwin Edijanto, Riza Hasan, Avesiena Primadiansyah

The Deep Mill Level Zone (DMLZ) is the fourth panel cave mine in the East Ertsberg Skarn System, (EESS) which lies 500 m below the producing Deep Ore Zone (DOZ) mine and up to 1,700 m below the surface. The interaction between the DMLZ and DOZ is occurring as the DMLZ cave grows vertically toward the DOZ footprint. During this process, a rapid change in the global mine system stress is anticipated. This change is forecasted to drive substantial changes in the magnitude and direction of principal stresses in the DMLZ and DOZ mines at PT Freeport Indonesia. These changes will bring the mine system closer to the ultimate capacity of the excavations and can result in significant impacts to mine stability if not managed. Critical to this management, is understanding cave growth and locations, as well as how these changes will impact stress conditions.

Apr 26, 2022

By S. Al-Thyabat

Conditioning of flotation feed is an important prerequisite for efficient flotation. This process depends on parameters such as conditioning time, slurry concentration and slurry pH. The objective of this paper is to optimize the conditioning process for the flotation feed. This was achieved by first conducting preliminary experiments at constant slurry pH to determine the significant ranges of slurry concentration and conditioning time. Then, factorial experimental design (32 experiments) was used to investigate the significance of the above parameters and their interactions on flotation recovery and grade. Statistical analyses using ANOVA approach showed that flotation recovery (R) and concentrate grade (g) were affected by feed conditioning. It was found that concentrate grade was linearly proportional to the slurry concentration and conditioning time, while flotation recovery was exponentially proportional to the conditioning parameters. A contour plot of the flotation response (recovery and grade) against conditioning parameters showed that the optimum operating parameters for flotation feed conditioning was a conditioning time of 1.5 to 2 minutes and a slurry conentration of 55% to 60%.

Jan 1, 2008

By Ray E. Harris

Introduction A resource of more than 122 Gt (134 billion st) of minable trona and mixed trona and halite underlies an area of about 3400 km2 (1300 sq miles) west of Green River, WY (Culbertson, in preparation) (Fig. 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6 Mt (6.7 million st) (Kostick, 1983). About 90% of this came from Wyoming trona. This enormous deposit occurs in the Wilkins Peak Member of the Green River Formation that is of Eocene age. This formation is derived from sediments deposited in a large lake named Gosiute. Lake Gosiute occupied the Green River Basin in southwestern Wyoming some 38 to 54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition when the trona deposits were formed. A total of 42 trona beds are known. Of these, 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation). The production of sodium compounds from the trona deposits in the Wilkins Peak Member began in 1896 when wells were drilled within the present boundaries of the town of Green River. The purpose of the drilling was for extraction of sodium carbonate brines. Sodium carbonate (sal soda) was removed from these brines at a plant in Green River. Bedded trona was discovered in 1938 in a core from an oil well drilled south of Westvaco. In 1947, the underground mining of trona began. Production has continued from 1948 to date. Currently, five companies are mining trona and producing soda ash from the Wilkins Peak Member in Wyoming. Additionally, Allied Chemical Co. mines and processes trona for Church and Dwight's sodium bicarbonate (baking soda) operation in Green River. Competition in the soda ash industry depends primarily on the efficiency of mining and refining, allowing for lower-cost production. Newer plants and mine designs should increase efficiency. Solution mining holds promise as an even lower-cost method of mining. Employment in the soda ash industry is declining since the newer mining and refining methods are less labor intensive. Declines in employment, however, may be offset as production increases. Due to the large resource, the availability of minable trona should not be a problem for perhaps hundreds of years. Geology of Wyoming trona deposits Forty-two beds of trona or mixed trona and halite occur in the

Jan 10, 1985

By K. Oraee

Mining of copper ore and the related industries play an important role in Iran?s economy. Copper ore production in Iran accounts for 75% of the total production in the Middle East. All activities related to copper, that is, exploration, production, refinement etc are owned and managed by state owned companies. Decisions have been made to privatize all these activities. To assess the success of this privatization process, different components of the industry must be subject to economic analysis. In this paper, the cost estimation of all operations has been carried out. The total potential and attainable revenues have also been estimated using historical data available from the industry. Risk is a major factor in all mining activities and the copper industry of Iran has been subject to risk factors arising from many internal and external variables. These variables have been recognized and their effects evaluated. The effect of risk on the economic feasibility of the operations in the industry has also been analyzed.

Jan 1, 2011

By J. F. Fiset, N. Bouzoubaâ, N. Reynier, C. Laviolette, Canadian Nuclear Laboratories

Canadian Nuclear Laboratories (CNL) is developing a disposal strategy for radioactive wastes, which contain significant amounts of uranium, cesium, and mercury. There are safety and economic incentives for the extraction of these elements before permanent storage in deep underground repositories. In addition, the actinide elements are also an important component in rare earth element (REE) ores and considered as impurities. Actinides separation from REE tailings is a significant concern in order to manage radioactive nuclides. Reprocessing mine wastes may present significant financial and environmental benefits. Experiments were carried out with radioactive cemented wastes (RCW) prepared at CanmetMINING. For all of the tested RCW batches, solubilisation yields are above 97% for Cs and 98% for U and Hg. Sulphuric acid leaching with potassium iodide improved the solubilisation of Hg by oxidation and formation of the tetraiodide complex (e.g. HgI4 2-, Kf = 2.1030). Cs and Hg were removed selectively by using potassium cobalt hexacyanoferrate (KCFC) and Lewatit TP214 ion-exchange resin respectively. U recovery using the chelating resin Lewatit TP260 was the most efficient. The presence of high iodine concentration improved the U uptake by the resin. The best U elution was obtained using 1 M Na2CO3, which resulted in 99% U recovery. U was then precipitated as sodium diuranate. A counter current effluent recirculation was performed successfully on RCW. The process was also applied to submerged tailings collected from two U mines and an REE ore. This paper presents an innovative process, using sulphuric acid and potassium iodide, for U, Cs, a

Jan 1, 2016

By George W. Huseman, W. D. Mcmillan

"INTRODUCTION Feldspars represent one of the most abundant groups of minerals and constitute nearly Go percent of the material contained in the igneous rocks. They are grouped in a series of related aluminum silicates with varying amounts of potash, soda, and lime. .Approximately 85 percent of the feldspar produced in the United States is used as a flux in the production of glass, pottery, enamel and sanitary ware, brick, and tile. Notwithstanding the abundance of feldspar in the earth's crust, the only deposits that are worked to any extent are the pegmatites or coarsely crystalline dikes where natural segregation of the constituents facilitates recovery of the feldspar with a minimum of free quartz, mica, tourmaline, garnet, and other iron-bearing minerals that are detrimental in most ceramic industries.Although there are three glassplants and numerous other ceramic industries in Texas, all of the feldspar used in these plants is from other States. In the Llano region of central Texas, however, there are numerous coarse pegmatite dikes consisting primarily of feldspar and quartz in ratios up to 3 to 1. One of the more important of these dikes is the Badu Hill deposit in Llano County, Tex., which was first described by Carl Chelf 4/ in 1942. Following an examination of the deposit by W. D. McMillan, engineer in charge of the Texas field office of the Bureau of Mines, in January 1946, a proposal was made to investigate the deposit by core drilling in cooperation with the Department of Ceramic Engineering, University of Texas. This report presents the results of the cooperative investigation, which was begun April 24, 1946, and completed May 17, 1946."

Jul 1, 1947

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes, Kevin Wegman

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptable cost and computational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By H. S. Kalman

A table of factors for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, at base conditions of 14.7 psia and 70° F, is presented. The table covers a pressure range from 10 to 10,000 psin in 10-psi increments and a temperature range of 0° to 120° F in 2° increments. The volume of helium is calculated from the observed pressure and temperature of the helium, expressed as a factor from the table, and the known internal volume of the container. The calculation requires a single multiplication. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1968

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001

Grey River Gold Mining Ltd commenced dredging alluvial flats in the Grey River Valley in 1989. Previous drilling indicated over 100 million cubic metres of gravels with some 90 per cent of the gold in the bottom seven metres. The dredge built by Rahco, Spokane, was innovative in a number of aspects but particularly in the fact that a separate ladder with a cutter and pump was used to strip the overburden and a bucketline to mine the gold bearing wash below. Metallurgical studies and exploration were initiated when the project commenced. Leasing and environmental considerations were investigated and action taken. While progress is being made, the operation at this stage is not meeting required production and performance. Main problems have been with the stripping system and wear.

Jan 1, 1990

By R. R. Sayers

There is probably no industry , trade , or art in which mercury is used but what has produced some cases of mercury poisoning . This is true of the mining and smelting of mercury , where the hazard has long been recognized . When the ore contains free mercury or the more soluble salts , and when the workings are underground and are poorly ventilated , cases occur , but there are a far greater number of cases among the employees about the reduction works . 3 In 1863 William V. Wells visited the mines at Almaden , * Spain , which were worked by convicts . He reported that the men at the furnaces suffered severely , being able to work only about one week out of four , when it was necessary to transfer them to places where the exposure was less . He states that "pale cadaverous faces and leaden eyes are consequences of even these short periods . " Mercury , like lead , when absorbed in small amounts at intervals , as daily, over an extended period of time will result in symptoms of poisoning . This is due to the fact that the mercury is eliminated from the body more slowly than it is absorbed . The frequency and severity of cases of mercury poisoning are far less with modern methods of mining and recovery of the metal than formerly . However , further reduction is possible and much can be done by both the workmen and the operators by following the proper precautionary measures , some of which are described in this chapter .

May 1, 1922

By A Dunne, R Kruger, H Coleman, P G. Laurens

External and internal challenges in mining are increasing the difficulty and complexity of operating mines. The external mining environment has a big impact on mining operations and is driving the focus on safety, sustainable mining, green issues, profitability and productivity. There is a very high emphasis on ‘reducing cost to improve’, lower mining and beneficiation costs by eliminating waste/inefficiencies (reduce people, use less consumables, multiskilling, etc). The internal mining environment is getting tougher to operate in, with the deposits being more difficult to mine, more difficult to manage due to external pressure along with issues associated with maintaining quality, etc.Technological and environmental developments too numerous to mention, mean that cost control models, reduction in human resource numbers, as well as other drastic measures to curtail expenditure and increase profitability have become part of everyday business. The capability to manage the mining environment in a systemic manner has been lacking and this increases the pressure for performance on those individuals operating and managing mines.Working smarter has become crucial to ensure that businesses optimise the use of their resources, become more safety conscious, more productive and remain cost-effective, while recognising the importance of sustainable mining now and in the future. The logic of determining and managing to the capability of the mining value chain will be examined and the underlying assumptions or beliefs guiding behaviour and decision-making will be highlighted.In order to identify the obstacles in the mining value chain that hinder achievement of its full potential, the following questions have to be asked:What are the factors that influence the performance of a mining value chain?What is the design capacity of the mine?How can the inherent flow and value capacity of a mine be determined?What types of solutions will allow a mine to operate at its inherent flow and value capacity?This article will discuss the way we plan, measure, assess and manage the mine value chain, by addressing the following factors:balanced capacity versus flow and value capacity designthe use of averagingoptimising individual components in a value chain versus optimising the whole value chain.Optimising flow and value through the mining value chain is one of the three pillars of Mineral Resource Throughput Management (MR™). MR™ is an entrenched and academically supported philosophy that has been successfully applied in the past decade in various mines throughout the world by EXXPLEO, a mining and beneficiation consulting company. EXXPLEO has partnered with HCL (a global IT company) to embed the MR™ philosophy, methodology and toolsets into a formal software product called Synchronised Digital Mining (SDM). The SDM system will provide mining companies with a sustainable platform to effectively apply the MR™ principles and toolsets effectively across all operations targeting increased productivity, efficiency and profitability without having to train operations and management staff into expert MR™ practitioners to successfully achieve the desired results.CITATION:Dunne, A, Laurens, P G, Kruger, R and Coleman, H, 2015. Optimising flow in the mining value chain, in Proceedings Iron Ore 2015, pp 437–442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Michael S. Wieland

Toxic fumes cause fatal and nonfatal incidents in underground mining, where the working environment tends to trap the fumes, hindering the restoration of nonharmful conditions. Workers can underestimate the residual fume toxicity and return to the work site too quickly. The toxic fumes from charge explosions depend upon a number things: formulation ingredients, mixture uniformity, water resistance, hole contaminates, rock hardness, and dust interactions. Hole-to-hole shock waves and rift compressions can partially desensitize charges, ruin the reaction kinetics, and worsen the fume toxicity. Traditionally the fume hazards for candidate explosives are resolved for a restricted set or tally of theoretical or measured fume components, transformed to standard reference conditions. The relative fume toxicity RFT is the resultant influence reckoned from a formulated sum of concentrations within the tally that are unweighted or weighted with chosen multiplying constants. The RFT result is compared to a rule criterion that represents the worst case tolerable fume toxicity stipulated by regulations or otherwise. The ranking and comparison of different hazard potentials that would otherwise remain unwieldy is rendered tractable by the common format of the RFT notation.

Jan 1, 1998

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By E. V. Cilento, R. C. Laotz, K. A. DiGregorio

"PULMONARY ALVEOLAR macrophages (PAM) protect the lungs by providing a first line of defense against inhaled foreign debris and bacteria. In this role PAM phagocytize foreign matter, secrete enzymes that augment microbial killing and digestion, and produce reactive oxygen me-tabolites (2, 3, 18, 19, 22, 26). However, in addition to this antibacterial function, PAM participate in a diversity of functions, such as tissue repair, lipoprotein metabolism, and immunoregulatory activities (11, 22).Studies have suggested the existence of a heterogeneous population of PAM with respect to immunologic function, enzyme release, phagocytosis, morphological characteristics, expression of membrane receptors, ad-herence, and superoxide (O2•) release (4-7, 10, 16, 21, 23, 28). This heterogeneity has been observed by analyz¬ing subfractions of PAM separated by cell density frac-tionation. For example, using guinea pig PAM, Dauber et al. (7) showed heterogeneity in cell density and size, morphological characteristics, and cytochemical properties, whereas Holian and co-workers (16) reported variations in migration, chemotaxis, O2• release, and pinocytosis among subfractions collected. Similarly, O'Neill et al. (21) observed functional heterogeneity in rat PAM with regard to phagocytosis, O2 • release, and lysosomal enzyme activity.Several investigations have reported a correlation between PAM activity and cell volume. Most studies have shown that O2 release from PAM increased with decreasing cell size (15, 21, 25), although Bielefeldt Ohmann and Babiuk (4) reported a decreasing trend. However, Gallin (13) has suggested that significant variability may even exist within density-defined or cell-volume subfractions that could lead to misinterpretation of results concerning PAM heterogeneity.A better understanding of the heterogeneity in O2 production may be obtained by using single cell meas-urements to evaluate whether functionally distinct sub-populations actually do exist. As such, the present study was designed to examine heterogeneity in O2 • release from single PAM using a recently developed electrooptical technique (8). The initial oxygen metabolite, O2•, produced by NADPH oxidase at the surface of the plasma membrane, was measured by quantifying the reduction of nitro blue tetrazolium (NBT I to a diformazan precipitate. Measurements were made from video recordings of individual cells stimulated by their adherence to the bottom of a culture dish. The cell volume and degree of spreading also were determined directly from the same video recordings, and the data were correlated with the initial rate and maximum amount of diformazan produced by the same cell."

Mar 1, 1992

By K. C. McMahon

This report is the result of the engineering efforts performed by the Mining Equipment Operations of FMC to develop methods of automating a continuous miner. This work was done as part of modification number three of the contract for the development of a miner/bolter system. As the demand for energy places an ever-increasing pressure on the coal mining industry to produce more coal, methods for underground mining which will increase productivity with a con-current increase in safety are being actively sought. Removing the machine operator from his station on the continuous miner and placing him at a safer location behind the machine while retaining his control functions via an umbilical cable or a radio link was an important first step. However, the problems of poor visibility, no control "feel", and the judgmental problems of controlling the sump distance and the shear limits have not been conducive to the productivity increase that is desired.

Jan 1, 1975

By H. Margolin, E. Ence

Two versions of the Ti-Mn binary diagram have been published recently.' , -0th diagrams show two compounds in the region between 40 and 70 wt pct Mn, but disagree as to the reaction in which these compounds are involved. The investigation of the manganese-rich portion of the Ti-Mn binary diagram was undertaken at New York University as part of an investigation of ternary systems with titanium and manganese in order to determine which of the proposed diagrams is correct. A number of alloys between 31 and 70 pct Mn were prepared in a manner similar to that described by Cadoff and Nielsen; except that low currents (110 amp in argon atmosphere) and long melting times (up to 20 min) were used to prepare the alloys. Compositions were determined from weight-loss data, assuming all loss as due to manganese. Heat treatments were carried out with relatively large pieces, since there was a tendency for manganese to be lost during heat treatment. When X-ray diffraction data was to be obtained, the central parts of heat-treated specimens were used to make filings or powders which were not heat treated. Specimens were heat treated from the as-cast state. Heat-treatment times were as follows: 1150°C, 1 day; ll00°C, 2 days; 1000°C, 5 days; and 900°C, 15 days. It should be noted that equilibrium was not attained at 900°, 1000°, and in one case, at 1150°C. Metallographic specimens were electrolytically polished and strain etched by a technique described elsewhere.' At least four, and possibly six, phases were found in the region investigated. On the basis of information available at this time, a completely self-consistent diagram cannot be constructed, and therefore data are presented only for those phases which have been identified by both X-ray and microstruc-ture. Of the compounds detected, the one highest in manganese is the Laves phase, TiMn,, which is hexagonal with a MgZn, type of structure.V he diffraction data for TiMn2 from a 70 pct Mn alloy annealed at 1150°C are shown in Table I. The c/a ratio and parameters of TiMn2 agree well with those of Wall-baum hnd Rostoker et al. The values obtained here are c/a = 1.641, a = 4.825A. Another compound is the y-phase which is estimated to contain about 60 pct Mn. The y-phase has a structure which is identical to that of TiMn, with c/a = 1.639, a = 4.906Å. The fact that y has a Laves-type lattice would suggest that TiMn, has a range of solubility which extends from the composition of TiMn2 (69.6 Mn) to that of y (60 pct Mn). However, this could not account for microstructures which, in the 60 to 70 pct Mn region, show several phases in both the as-cast state and after annealing at 1150°C. Fig. 1 shows a two-phase structure of a 60 pct Mn alloy annealed at 1150°C. The phases present are y (white) and e (dark). If y were TiMn, then, according to Rostoker et al.,' the second phase of Fig. 1 should be P-Ti. The diffraction data for the 60 pct Mn alloy of Fig. 1 are shown in Table I. The starred d-values are from the e-phase and these lines do not correspond to those of &Ti. Comparison of as-cast and 1150°C microstructures of the 60 pct Mn alloy indicates that e precipitated from y. Since y has a

Jan 1, 1955

By Deepak Malhotra

This paper discusses the need for periodic auditing of mineral processing flowsheets and the potential benefits a company can gain from a study of this nature. A carefully designed flowsheet auditing can have a significant impact on the metallurgical performance in the plant. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1986