Search Documents

By P. W. Ramsey, G. L. Werley

THERE have been numerous examples in recent years of the similarity between aging behavior and diffusion behavior, where a plot of the logarithm of the aging rate versus the reciprocal of the absolute temperature yields an approximate straight line, analogous to a similar plot of the diffusion coefficient D (log D vs. 1/T). Austin and Rickettl have pointed out that this linear relationship holds empirically for the de- composition of austenite into pearlite and bainite in carbon steels, and Robertson' has shown similar trends in the aging of 24S-type aluminum alloys. Jenkins and Bucknall³ have also demonstrated the association between aging and diffusion rates for nickel-silicon-copper alloys. Jetter and Mehl,4 however, have shown that the maximum rate of dilation of a series of aluminum-silicon alloys does not show this linear relation and Mehl5 has pointed out that careful study of available knowledge indicates that "aging rates increase with temperature approximately exponentially, whereas D increases precisely exponentially." He further notes that "the rate of aging at a given temperature is the greater the lower the melting point of the alloy, which is also true for D." This paper describes the aging changes occurring in a zinc-25 pct manganese-15 pct copper-0.1 pct aluminum die casting alloy. It was found that this alloy does show this linear relationship and use was made of this relationship to estimate aging rates at low temperatures from data acquired at elevated temperatures. It should be noted that the aging reaction is being studied only indirectly, using changes in certain properties as criteria of the progress of the phenomenon. This alloy is purely an experimental one and is not available commercially. Zinc-Manganese-Copper System: The zinc-rich portion of the zinc-manganese-copper diagram which is of significance in the present work is quite uncertain. X ray examination of the alloy as die cast shows a phase similar to the epsilon phase (hexagonal close packed) of the copper-zinc system. All of the data accumulated indicate that the epsilon phase of the zinc-manganese-copper alloy is stable at high temperatures; that is, 500°C or above. Below this temperature a new phase is precipitated on annealing, and a decrease in specific volume occurs. At elevated temperatures this phase change occurs quite rapidly, while at room temperature the alloy has shown no change after several years. According to X ray data, this precipitated phase resembles the gamma phase (cubic) of the copper-zinc system, a hard and brittle structure. From examination of the microstructure and from X ray examination of the alloys annealed at

Jan 1, 1951

By James Westfield

Following is a brief resume of the Division's activities that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1961

By A. L. Edwards

A two-year study focused on current noise exposure levels in the South African mining industry, aimed at helping the Mine Health and Safety Council of South Africa meet its milestones for eliminating noise-induced hearing loss (NIHL). Methods A multi-task methodology was adapted from international baseline studies to determine the exposure to noise in both large-scale and small- to medium-scale mines. Results On average, 66.7 per cent of the employees sampled in year 1 and 78.4 per cent in year 2 were exposed to noise levels of above the 85 dB A legislated occupational exposure level. Conclusions Information obtained through the study could be developed into a national personal noise exposure database, including audiometric results, equipment noise emission levels and initiatives for noise engineering control by mines and equipment manufacturers to facilitate targets of eliminating NIHL. Keywords Noise exposure levels, mining industry, noise-induced hearing loss

Jan 1, 2011

By Yu A. B

An experimental study of the packing of a coal heap has been carried out. The bulk density of a coal heap is considered as a function of a number of variables, viz flow rate, conveyor belt speed, the height of the disengagement point of the conveyor belt, coal particle density, moisture content, the size of the heap and coal particle size distribution. The effects of the dimensionless numbers resulting from dimensional analysis on the packing density of a coal heap have been experimentally examined and analysed. Based on the experimental results, equations have been formulated for the estimation of the bulk density of a coal stockpile. The validity of these equations are checked by comparing the predictions with measurements of real industrial Stockpiles.

Jan 1, 1991

By Chris D. Shewmaker

So you want to install 2,600 augered cast-in-place piles, about 155,000 lineal feet, in 33 working days? It can be done. The Public Service Enterprise Group (PSEG) decided to build a combined cycle power plant in Lawrenceburg, Indiana. PSEG selected Fluor Constructors Indiana, L.P. to design and build the plant. Fluor Constructors, in turn, selected Richard Goettle, Inc. to install the piles. The initial plan was to install the 2,600 piles in 33 days, working six (6) ten hour days per week. After successfully installing and performing four pile load tests - up to 300 ton capacity - we set out to complete the work and meet the aggressive schedule. After three weeks of installing an average of 75 piles a day with three drill rigs, Fluor relaxed the schedule because we were so far ahead of their projected construction sequence. We elected to continue drilling on a ten-hour day, five days a week schedule. In all, we installed nearly 2,800 piles, totaling 175,000 lineal feet, in about 47 days.

Jan 1, 2004

By E. Roman, M. Brissette

"For its end of life, Kemess Mine processed its difficult-to-treat hypogene ore from the east pit, which is a lower grade copper and higher pyrite content gold ore. Metallurgical testwork showed that improvement was possible with finer grinding. In July 2010, small grinding media were introduced into the regrind mill resulting to a nearly 50% decrease of the power draw with a finer grind, an increase of 1.1% in the final copper grade, an increase of 1.2% in copper and 2.9% in gold recoveries at the cleaners. The overall recoveries of copper and gold increased by 0.6% and 1.3% respectively.INTRODUCTION Kemess Mine was located at 430 km North West of Prince George in North Central British Colombia. Its production started in May 1998 by Royal Oak Mines and was acquired by Northgate Exploration in 2000. Kemess reached its end of life production with its last of production on March 9th, 2011. The concentrator nominal capacity was 56,000 TPD consisting of a primary gyratory crusher feeding two identical conventional SAB circuits totalizing 35,840 kW available for grinding. Rougher flotation consists of four parallel rows of eight 130 m³ tank cells to produce a concentrate of 2% Cu and 6 gr/t Au which was pumped to a 5 m x 10.8 m regrind ball mill. The regrind installed power was 4,480 kW to generate a final grind of 80% passing 40 microns. This product fed the two stage cleaner flotation circuit, first stage being two parallel rows conventional 17 m³ Denver cells and second stage, two 3.3 m x 11.0 m flotation columns in series, designed and constructed by Kemess, to produce a 22% copper concentrate grade. The cleaner flotation middlings were returned back to the regrind mill (Froehling, Mohns, Roman & Grady, 2005; Froehling, Mohns, Rajwani & Fullam, 2007). The large copper-gold porphyry deposit was composed of 15% of oxidized supergene and leach cap ore and 85% of hypogene ore having three major alteration zones, mainly characterized by their sulphur/sulphide content. Chalcopyrite is the main copper mineral species with minor bornite. Gold was mainly present as free gold or electrum. The first alteration zone consisted of a phyllic alteration characterized by moderate and intense sericite alteration which had the highest mill throughput and twice the mine grade when in contact with the supergene horizon. The second zone consisted of a potassic alteration characterized by more competent groundmass and moderate to intense quartz stockwork which had a slightly lower mill throughput. Finally, a third alteration found beneath and on the east side of the deposit having almost no quartz stockwork and hardened groundmass, sulphide content is two to four times more. This zone had the lower mill throughput with significant drop in the mine average gold and copper grade. Through its mine life, the average life of mine copper head grade was 0.21% Cu and 0.64 gr/t Au. Head grades began to decrease from 2008 to be substantially lower in 2011 as shown in Table 1."

Jan 1, 2012

By F. B. Tough, B. H. Scott

"Petroleum engineering is a comparatively new branch of engineering, with which few people, even petroleum operators and mining engineers, are thoroughly familiar. Petroleum engineers are responsible for the accurate keeping of well logs and all pertinent data upon formations encountered, for the careful analysis of such information, and recommendations as to most suitable places for drilling, for detailed study of methods of drilling, casing, and so on in order to obtain maximum production for a minimum cost.The Bureau of Hines has from time to time carried on work in all branches of petroleum engineering in the various fields of the United States. Such work is also being carried on extensively by the California State Mining Bureau, which has in its employ a number of men who have had, besides their technical training, actual experience in oil field work. This is about the only state at the present time which is carrying on this work in a definite way. It has therefore been the practice of the employees of the Bureau of Mines to go to other states and give such advice and assistance as might prove of value in development work and in prolonging the production of the fields."

Jan 1, 1920

By Jr. Herty

As the problem of inclusions in steel has become increasingly important, more and more attention has been paid to the source of the oxide inclusions in steel. In killed steels the oxide inclusions are traceable to the reaction of deoxidizers with the iron oxide dissolved in the steel during the refining period of the open-hearth heat. In a large class of steel known as "rimming steel" the action of the steel during solidification depends entirely on the gas evolved, and this evolution in turn is controlled by the amount of iron oxide in the liquid steel in the mold. It is therefore of great importance to be able to determine the amount of iron oxide dissolved in steel and to devise methods for the control of iron oxide in any class of steel. The object of the present investigation was to obtain a true value of the oxygen con-tent of liquid steel. If the steel has not been deoxidized, the greater percentage of the oxygen is present as iron oxide in solution.

Jan 1, 1932

By Bruno Gemmi

A new warehouse built with prefabricated components over an area underlined by soft marine soil deposits started showing differential settlements well before its completion. Its 103 spread footings carrying up to 4,000kN (450t) axial loads had been cast on jet-grouted columns extending and penetrating a layer of sand at a depth of 10m (33ft). Investigations performed to assess the wholeness and consistency of the jet-grouted columns revealed a state of loose jet-grouted masses and uncontrolled, off target migrations of the jet-grouting. Most of the jet-grouting itself was settling. The following remedial solutions were suggested: 1. Construction of new and better controlled jet-grouted columns. 2. Cement-based soil grouting. 3. Expanding resin injections. 4. Minipiles drilled-through the existing footings and reaching into a denser layer of sand existing at 23m below grade. Remedial solution 1. was immediately discarded due to cost and the possibility of a repeating failure in this non-granular and highly compressible soil. Tests of remedial solutions 2. and 3. were carried out. The outcome of the grouting was monitored by Electro Resistivity Tomography (ERT) (Bares et al., 2003), an innovative 3D electro tomography procedure showing where grout had been actually placed and its migrations off target. A successful 4,000kN (450t) load tests confirmed the validity of the solution. Finally, upon the completion of a successful load test, solution 4. was chosen. It supplied the highest degree of reliability thanks to the ease of controlling the final and actual location of the minipiles and to the higher safety factor provided. All remedial work to install the minipiles was eventually performed inside the building. Additional load tests and settlement measurements confirmed the adequacy and success of the chosen solution.

Jan 1, 2011

By G. D. Buson

Driefontein Consolidated Limited has a proud history in the South African gold mining industry dating back to March 1945 with the formation of the West Driefontein Gold Mining Company. The reclamation gold plant at West Driefontein was originally built as a uranium recovery plant in 1970. With the collapse of the uranium oxide yellow cake market, the uranium plant was closed in 1988and successfully converted into a gold plant, recovering gold from repulped tailings dams1. The West Driefontein Reclaim plant utilized milling, leaching, conventional rotary vacuum filtration and cementation to recover the gold at a rate of 200,000 dry tons per month. The No. 1 tailings dam (at a head grade of 0.8 Au g/t) began to near the end of its life during 1996, and the next slimes dams to be treated, the No. 2tailings dam (at a lower head grade of 0.56 Au g/t) was found too marginal for reprocessing using the filtration technology. Alternate technologies were investigated, particularly the carbon-in-pulp (CIP) plant based on the Anglo-American Corporation (AAC) pump-cell technology at the Vaal Reefs Exploration and Mining Company?s East gold plant which was operating profitably at lower head grades2. The AAC pump-cell technology is based on the carousel mode of operation2. The suitability of CIP technology for the West Driefontein Reclaim plant was investigated using a pilot plant pump-cell supplied by Kemix The data gathered were utilized in sizing a full scale AAC pump-cell plant. This plant was motivated, built and commissioned on the 22nd of November 1996. Incorporating 6 eighty cubic metre AAC pump-cells. The West Driefontein Reclaim plant initially treated repulped slimes dam material. A subsequent change of feed material to current arisings (from the main gold plant) occurred in1997 in order to convert mills for waste rock treatment. Currently the reclaim plant treats a combination of current arisings and waste rock (milled at the reclaim site). The new CIP plant replaced twenty-seven rotary vacuum filters. A comparison between the filters and CIP in terms of operating costs was undertaken, as well as a performance analysis of the CIP plant to determine its flexibility in terms of variation of the throughput, pulp density, gold input, leaching efficiency prior to CIP, and the rate of carbon movement.

Jan 1, 1999

As part of the United States Department of the Interior, Bureau of Mines Health and Safety Research Program, Walter C. McCrone Associates, Incorporated has examined 71 samples of airborne mine dusts using the techniques of x-ray diffraction, electron microprobe analysis and light microscopy. This report details the procedures which were used in this work and documents the results which were obtained.

Jan 1, 2011

By W. L. Acherman

The Bureau of Mines found the chemical and galvanic corrosion behavior of the TZM and molybdenum-30 tungsten alloys to be generally equal or superior to that of unalloyed molybdenum in many aqueous solutions of acids, bases, and salts. Notable exceptions occurred in 1 [N] nitric acid, where both alloys corroded appreciably faster than molybdenum. In mercuric chloride solutions, the TZM alloy was susceptible to a type of crevice corrosion which was not due to differential aeration. The alloys were usually not adversely affected by con-tact with dissimilar metals in galvanic couple experiments, but the dissimilar metals sometimes corroded galvanically. Both alloys were resistant to substitute ocean water spray at 60° C.

Jan 1, 1968

By Guojun Qi

This work relates to wafer bumping technologies for flip chip packaging applications in the electronics industry. Nickel and its alloys are alternative under bump metallization (UBM) materials because of their slower reaction rates with Sn-based solder as compared to Cu-based UBMs. In this study, we compared the morphologies of the intermetallic compounds (IMC) formed between Sn-bearing solders (Sn3.5Ag and eutectic Sn-Pb) and two types of nickel- based UBMs, electroless Ni-P (EN) and sputtered nickel. Both chunky-type and needle-type of intermetallics were observed between the EN UBM and the solders. In the case of sputtered Ni UBM, there is only a layer of scallop-type intermetallics formed. The morphology change and growth kinetics of the IMC in thermal aging process were analysed. Kirkendall voids were noticed from samples of Sn3.5Ag solder vs Ni-P UBM that have undergone prolonged thermal aging at high temperature.

Jan 1, 2003

By J. C. Bayles

Jan 1, 1885

By Andrew J. Petruska, Rik Banerjee

This study explores implementing a machine learningbased system to generate a 3D surface repre- sentation of the roof and support straps in the mine. Event cameras have been chosen for their performance in high-dynamic-range lighting conditions and for their low latency. To enable automated drilling and bolting, 3D vision using eventbased cameras has been developed. A ground-truth set is created using two, time-synced event cameras and a LiDAR camera. These sensors are used to construct a ground-truth dataset of corresponding event- camera images and surface maps from the LiDAR. The network is tested with stereopairs of event images and produces a depth image with ±5 mm RMS error on average across 1000 test images.

Feb 1, 2024

By S R. La Brooy, T Giraudo, I C. Ritchie

The treatment plant at the Macraes Gold Project in New Zealand processes a carbonaceous, refractory sulphide gold ore. Since its commissioning in 1990, there has been a programme of continuous improvement of the plant, leading to higher recovery, increased throughput and low operating costs. During this time, a number of processes for treating both, or either, the preg-robbing carbonaceous fraction of the ore and the refractory sulfide fraction have been evaluated, trialed and utilised. The latest phase involves the installation by Minproc of plant utilising Newmont Gold's Pressure Oxidation Technology, a process which is anticipated to mitigate both problem factors when commissioned in 1999.

Jan 1, 1998

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

By Utley Wedge

(Cleveland :Meeting, October, 1012.) In general, the art of securing copper from sulphide ores or concentrates may be said to consist of : (1) separation, in the molten state, of copper sulphide with some iron sulphide, from the great bulk of gangue-material, followed by (2) elimination of sulphur and iron from the molten matte, by oxidation and fluxing, leaving metallic copper. The definition is made broad enough to cover the general practice, whether or not the ore or concentrate is given a preliminary roast for the removal of surplus sulphur. The above process, which I will designate as the smelting process, makes necessary the presence in the ore, or the addition thereto, of such silica, lime, and iron as may be necessary for the formation of a light and fusible slag, together with sufficient sulphur and iron for the formation of copper-matte, and also the addition to the matte of sufficient silica for the oxidation and fluxing-out of the iron. These items, together with the cost of fuel sufficient for melting the mass, constitute important items of cost in the copper-smelting process. Numerous cases where fluxing-materials are scarce or dear, or where fuel is expensive, have caused special attention to be given recently to the wet process of copper-extraction, which may be designated as consisting of forming soluble copper salts which are then washed or leached out of the ore or concentrates by dissolving in water or acid. Metallic copper may then be secured from the solution of copper salts by electrolysis; by cementation; or copper can be brought out of the solution as a * Presented also at the Joint Meeting of the Institute and Section IIIa, Metallurgy and Mining, of the Eighth International Congress or Applied Chemistry, New York, N. Y., September, 1912, and here published by mutual agreement.

Dec 1, 1912

By W. D. Johnston, T. P. Thayer

THE minerals that collectively are known as chromite form an isomorphous series of the general formula (Mg,Fe) 0. (Cr,Al,Fe) 203. So wide is the range in chemical composition in this group that chrome ore consisting entirely of the mineral chromite may range from less than 30 pct to more than 60 pct Cr203. The most comprehensive published data on the chemical com- position of chromite are by Stevens,62 who made complete analyses of 52 samples of chromite concentrate from many localities in North, Cen- [ ] tral, and South America. These samples were mechanically purified to remove associated silicates and might be regarded as the cleanest chromite that could be obtained by any mechanical milling process. Fig 1 shows the predominant zone of isomorphism, within the triangular prism of composition defined by the mineralogical end members of the series, wherein his analyzed samples fell.

Jan 1, 1949

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.