Search Documents

By H. A. J. Wilkens, H. B. C. Nitze

From time to time papers treating of specific cases of Southern gold-mines and mining have appeared in the Transactions of this Institute, as well as in other journals and publications. Mr. George I?. Becker, of the United States Geological Survey, made a reconnaissance of the Southern Appalachian gold-belt during the fall of 1894; the results of his investigations are published under the title of "A Reconnoissance of the GoldFields of the Southern Appalachians," in the Sixteenth Annual Report of the Director of the United States Geological Survey, 1894-95 : Part III., " Mineral Resources of the United States." Mr. Becker has treated the subject mainly in a scientific geological manner. We present this paper to the members of the Institute as requested by the Secretary last May, with the object of covering the ground from a more practical and technical standpoint. The notes for this paper were made in a large measure from personal observations, gained chiefly during the past summer on a trip through the field. In connection with this trip we collected a suite of typical hand-specimens, representing the gold-ores and wall-rock from the more important localities. This collection forms a part of the exhibit

Jan 1, 1896

By D. G. F. Hedley, F. Grant

"In 1958, the Ontario Department of Mines appointed a committee to study the accident situation and mining methods used in the uranium mines in the E1liot Lake district. This committee reviewed the existing knowledge on mine design, pillar support and roof spans and came to the conclusion that scientific knowledge had not yet reached the stage of producing rational design procedures which would reduce the dependence on trial-and-error methods. Since that time, the Mining Research Centre has made numerous stress measurements in two mines to define the pre-mining and pillar stresses. A comprehensive series of tests has been done in the laboratory to measure the compressive strength of the rock; a geological survey of the region has been made to evaluate tectonic stresses; and a survey was done on mining conditions with regard to stable and unstable pillar configurations. This information has been used to evaluate pillar design as effected by pillar width and height, depth below surface, extraction and pre-mining stress fields. The resultant design of pillar widths and corresponding extraction as the depth increased is in line with past and present experience in these mines. The information available on roof stability is still insufficient to design stable stope spans with the same degree of confidence; experience and trial-and-error methods are still required."

Jan 1, 1972

By H. B. Humphrey, F. E. Cash

The Southern Appalachian coal field extends southward across Tennessee in a belt about 50 miles wide between the eastern and middle sections of the State. The earliest record of the production of coal in Tennessee is for 1840, and the first inspection laws were passed in 1881. In 1887, a second act of the legislature created the office of Chief Inspector, but little was done until 1891 when a new act was passed giving to the Department of Mines added duties and powers. Since that time, except for the years 1915 to 1918, com¬ prehensive annual reports have been published. Data for the tables given in this paper are taken from these annual reports, from those of the Southern Appalachian Coal Operators' Association, and from the publications of the United States Bureau of Mines, which has main¬ tained a station at Jellico, Tenn., since 1911. Complete figures for 1930 are not available yet and they are not included in the averages. The State Department of Mines, the operating companies, and the United States Bureau of Mines cooperate in accident-prevention work. It is the purpose of this report to present in uniform tables the available statistics in regard to fatal accidents in Tennessee and in the coal mines of the United States, in order that the progress in mine safety in Tennessee may be compared with that of the country as a whole, and the present period may be compared with various periods of the past, to indicate the main points of attack in the reduction of accidents.

Sep 1, 1931

Electricity will play a major part in providing energy services in the 21st century. Ecologically Sustainable Development (ESD), that is accommodating the needs of the present without compromising the needs of future generations, will provide a focus for optimising the use of electrical energy. Environmental externalities may redefine the cost structure of electricity. Strong corporate environmental management will ensure that current environmental objectives are met and that future ones, identified by the ESD process and environmental externalities accounting, can be developed and implemented by receptive business managers. This paper addresses the current environmental issues of electricity production. It outlines a management strategy for the SECV becoming a community leader in protecting the environment. ESD is discussed in terms of using non-renewable resources wisely, extending their availability and putting in place mechanisms which ensure their ultimate substitution by renewable resources and conservation. The paper explores options for dealing with costing environmental externalities, particularly in relation to greenhouse emissions.

Jan 1, 1992

By Tom Barczak

Early in my career, while giving a presentation on shield design for longwall mining at one of the International Conferences on Ground Control in Mining, the late Jim Scott told me that I was finally getting it, because ?I was starting to think like a rock!? Although I didn?t realize it at the time, those few words changed my career forever. At the start of my career, I did a lot of laboratory testing, taking advantage of the unique capabilities of the Mine Roof Simulator to study the performance and design characteristics of longwall shields. I had a pretty good handle on what made shields work and what made them fail, but I was still struggling with how and why they develop their in-service loads and what they were actually controlling as opposed to being passive bystanders in a world beyond their control. It became clear to me that the simplistic models of dead weight loading could not explain the behavior I saw and measured underground. The problem did not go away when I started studying standing support systems. Again, I learned much about the strength, stiffness, and stability of these supports and helped the industry develop several new support products that attempted to provide more efficient support designs. But here, too, the simplistic models of dead weight loading did not seem to fit for me. That?s when I began to incorporate the ground reaction concept as a way of integrating the support response and the ground behavior into a cohesive design methodology. The concept has its limitations, no doubt, but I believe some form of it will be the future of not only designing supports but also, in the broader sense, enhancing the engineering aspects of ground control. The paper presented at the International Conference on Ground Control last year by Esterhuizen (2010) on pillar behavior is evidence of this. Think like a rock. Jim Scott was right. It takes two to dance. You can?t dance alone and you will never understand ground control by thinking like a support! ?Dumb as a box of rocks?? I don?t think so. The answer lies in the rocks!

Jan 1, 2011

By A. Rajoria

A dynamic process model for predicting the fluidized bed roasting of copper concentrates with high arsenic content is presented in this work. Mass and energy balances were performed based on roasting mechanism derived from thermodynamic data of species. The reaction rate data, obtained from pilot plant studies on major reactions, were used in tuning the kinetic parameters of the model. DEAS, a dynamic simulation package, is used in setting up the fluidized bed roaster plant model. The effect of process parameters such as concentrate feed rate, concentrate composition, airflow and cooling water rate on the temperature and conversion of roasting reactions are analyzed. The plant model captures the highly transient conditions occurring during the plant start-up, shutdown and other process perturbations. The application of this model in constructing a virtual plant environment for validating the operating procedures and operator training is presented.

Feb 23, 2014

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010

By L. A. Neumeier

The Bureau of Mines evaluated creep properties of Zn-Cu-Ti alloys that were annealed after finish-rolling either cold) or at 480° F (249° C). Compositions ranged up to 1.25 pct Cu and 0.36 pct Ti. Most data are for sheet annealed after finish-rolling to 92-pct total reduction. Annealing times were varied at temperatures between 320° and 560° F (160° and 293° C). For a number of the alloys, annealing after hot-rolling at 480° F affects creep properties very differently in longitudinal and transverse sheet directions. The detrimental result is that the anisotropy in creep properties between the two directions can be vastly increased. Conversely, specific annealing treatments of certain heavily cold-rolled alloys result in surprisingly low anisotropy in creep properties and the low anisotropy coincides with excellent creep resistance for both directions. Supplemental data are presented on tensile, hardness, and thermal expansion properties, and microstructures.

Jan 1, 1972

By M. Saghaeian, R. Hejazi, R. Barreiro, M. Tavousi, M. Ahadi, O. Asghari

"Banded iron formations are the major iron source for producing high grade concentrate. BIF are generally lower grade and more difficult to extract. In order to know how best to process BIF ore, it require comprehensive knowledge on ore bodies even in the early stages of the mining process. Geometallurgy combines geological and mineral processing information and allows for higher flexibility in response to changes in the plant feed when mining different parts of the ore. This can lead to economic benefits, owing to improved plant operation, yet is time consuming and correspondingly costly. The main focus of this paper work has been to develop a comprehensive geometallurgical testing framework for developing Yogi BIF low grade magnetite deposit located at Western Australia. In order to provide successful geometallurgical mapping, was collected data from several different disciplines (geology, chemistry, mineralogy) and parameters (physical properties, metallurgical response and geotechnical measurements) during drilling activities and test work. The investigation shown magnetic separation behavior of material had high variation and is most important element in the proper design of ore beneficiation plant. This paper provides an improved and efficient magnetic separation test methods used for the investigation of separation behavior and variability of the Yogi Ore deposit and evaluates their applicability and potential in the geometallurgical context. In this paper a small-scale magnetic separation has been developed that allows estimating from single pass separation test using small amounts of sample material. Verification of the evaluation method and validation was done with different mineral systems."

Jan 1, 2018

By S. Castro, L. Uribe

Seawater can be considered as a particular process water with a high concentration of NaCl (about 0.5- 0.6 mole/L) and high concentration of hydrolyzing metal cations (mainly, Mg2+ and Ca2+ ions). Micro-flotation tests, induction time measurements, and zeta potential measurements have been used to investigate the effect of these ions on the natural floatability of molybdenite. The results demonstrate that molybdenite is strongly depressed in the alkaline pH range over which hydrolysis products of Mg2+ and Ca2+ ions are formed. At pH 10, colloidal magnesium hydroxide seems to be responsible for molybdenite depression in seawater and in Mg2+ solutions. This is also supported by the measurements of the effect of Mg2+ ions on the zeta potential of molybdenite. The mechanism of depression of molybdenite with Ca2+ ions is different, and depression takes place in the pH range were Ca(OH)+ complexes are formed, below the pH of precipitation of calcium hydroxide. Adsorption of the cationic hydroxy species and/or hetero-coagulation of the positive charged colloidal hydroxide on the negative charged molybdenite particles seem to be the main mechanisms involved.

Jan 1, 2014

By Kray Luxbacher, Erik Westman, Peter Swanson

Three-dimensional time-lapse velocity tomograms were generated to image stress redistribution around a longwall panel to produce a better understanding of the mechanisms that lead to ground failure. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Most similar studies have utilized active sources including longwall shearers, controlled explosions, and hammer blows. These active sources generally require a person to initiate and measure the location and time of the source, and are not conducive to continuous monitoring. This method utilizes mining induced microseismic events as passive sources and lends itself well to continuous monitoring. Two event location methods were compared in order to move toward quantification of tomographic results in terms of ground conditions. Additionally, LAMODEL was utilized to determine the expected stress distribution around the longwall panel and compare these images to the velocity tomograms. Eighteen tomograms were generated, one per day, and high velocity regions in the set of tomograms generated from the initial location algorithm correlated with abutment stress redistribution predicted by numerical modeling. This research is significant as it has the potential to improve safety in underground mines and is the only example of long term passive velocity tomography implementation for the purpose of inferring stress redistribution around an area of active mining. Though still immature, this technology has the potential to allow mine personnel to image areas of active mining on a regular basis and detect areas with anomalous velocity distributions indicating potential safety hazards.

By Wen Lan Chen

In the plant where the 800m diameter cyclone was tested, 500 STPH of 50m x 0 raw coal was pulped in a heavy medium tank and pumped originally to four 700mm heavy medium cyclones. For the test one of these units was replaced by an 800mm diameter cyclone with the subsequent feed pressure for both units sets at approximately 15.0 psi. Since this was a feed to zero plant, an appropriate bleed of heavy medium to the dilute medium circuit was established to en- sure that the cleaning of the 500m x 0.5mm raw coal would not be adversely affected by high levels of 0.5mm x 0 fine coal present in the heavy medium. The medium gravity measured varied between 1.41 and 1.43. During a three-hour test on June 10, 1983, the raw coal sample was collected from the feed belt while the clean coal and refuse samples were collected separately at proper locations along the product streams of the two different diameter cyclones. All of these samples were shipped to the laboratory for screen and sink- float analyses. The raw coal screen and ash analyses are shown in Table 1.

Jan 1, 1984

By L. P. Weber

During the years 1983-1987, a research programme, jointly performed by the steel producers ARBED, British Steel Corporation, Peine-Salzgitter, Unimetal, and co-sponsored by the European Community for Steel and Coal (ECSC), has been carried out on steel H-piles of different shapes. The initial aim of the testing programme has been the improvement of bearing capacity, both in sandy and clayey soils. At two test sites, standard H-beams are compared to H-piles with different types of laggings or to H-piles grouted both under low and high pressure. In this paper and in view of the open european market in 1992, the H-pile capacities and their corresponding allowable loads, determined from codes, recommendations and computation procedures in use in Belgium/Luxembourg (B/L), France (F), Federal Republic of Germany (G), and the United Kingdom (UK) as well as their evaluation from dynamic CAPWAP and Case methods are compared to the static capacities measured in-situ. In addition, procedures for estimating the load/movement behaviour of H-piles from CPT, pressuremeter, and CAPWAP are compared to the measured curves.

Jan 1, 1991

By Edgar Schach, Tom Leistner, Markus Buchmann, Urs A. Peuker, Martin Rudolph, Marius Kern

"In this study, the flotation characteristics of a cassiterite-bearing fine-grained and complex skarn ore from a deposit in the Ore Mountains is investigated. The tests are performed using an oil-assisted column flotation approach to process very fine ore fractions and avoid losses of cassiterite into the tailings. First, process parameters are obtained for a finely ground artificial mixture of quartz, magnetite and cassiterite, simulating the real ore. Thereby, magnetite is used, as iron oxides can have a detrimental effect on the flotation due to a similar flotation behavior. In addition, they can act as a source of multivalent ions, which are known to reduce the concentration of collector molecules, active for flotation. Based on the results, selected parameters are further tested for cassiterite skarn ore from the Hämmerlein deposit including a pre-conditioning and a water exchange step to remove ionic contaminants. The process response is analyzed in detail by XRF (X-ray fluorescence) and MLA (mineral liberation analysis) to get a better understanding of the behavior of the single ore components. Sulfosuccinamate type surfactant is utilized as the collector, emulsifier and to reduce the froth destabilization through nonpolar oil. Sodium hexafluorosilicate is added as the depressant.INTRODUCTION Complex skarn ore deposits containing considerable amounts of tin, indium and other metals are located in the Ore Mountains region (Germany). In this study, a skarn ore from the Hämmerlein deposit was investigated. Due to the finely disseminated nature of this ore, past beneficiation attempts failed, and the ore was considered economically unprocessable. However, increasing resource demands brings it back into focus (Schuppan and Hiller, 2012). Cassiterite is the main tin bearing mineral in this ore. Due to its high density (~7 g/cm³), the predominant beneficiation technique is gravity separation (Angadi et al., 2015). Tin ores from disseminated deposits have to be extensively comminuted to reach a sufficient degree of liberation of the cassiterite grains. As cassiterite has a brittle nature, it is preferable enriched in small size fractions, during comminution (Angadi et al., 2015). Gravity separation methods become more and more inefficient for particles smaller 40 µm (Falcon, 1982), causing tin losses of up to 30 to 40wt.-% (Angadi et al., 2015). Thus, froth flotation of cassiterite was first utilized in Altenberg in the Ore Mountains as an additional processing step to reduce the cassiterite losses into gravity separation tailings (Bulatovic, 2010; Gruner and Bilsing, 1992). Although the reported lower size limits for an effective cassiterite floatability are often smaller compared to other minerals, the flotation performance is in general decreasing for small particle sizes < 10 µm (Trahar and Warren, 1976). Therefore, different approaches have been already investigated for the flotation of such fine cassiterite fractions to overcome the limits in particle size. Bilgen et al. investigated the shear flocculation of cassiterite with a sulfosuccinamate collector (Bilgen et al., 1994). The agglomeration flotation of cassiterite has been tested by Schubert et al. (Schubert et al., 1966), in which the selective coagulation of fine hydrophobic particles and oil droplets leads to an increase of the effective particle size. Recently, Leistner at al. investigated an oil-assisted agglomeration flotation for ultra-fine cassiterite ore fractions (Leistner et al., 2016). However, a poor response due to an increased concentration of Fe and Ca ions, unselective oil/gangue coagulation and froth instability, that is caused by oil/frother interactions, has been observed."

Jan 1, 2018

By M D. Taylor, G Duclaux, K Atkinson, L A. Fisher, A R. Latham, M F. Gazley, S J. de Beer, C M. Tutt

Geological logging by mine and exploration geologists involves the application of a logging code that requires a geologist to make a subjective decision to classify a particular rock unit. This will most likely result in inconsistencies in logging that will be difficult to monitor or assess over time. A potential solution to this problem is to have an objective method to determine the true nature of a given rock unit. This can be achieved using portable X-ray fluorescence technology (pXRF), as large geochemical data sets can be collected rapidly and at low cost. Plutonic Gold Mine (Plutonic), Western Australia, has a growing data set of more than 150 000 pXRF multi-element analyses from core and underground face samples, reconciled to Au fire-assay concentration, and logging codes. This study investigates and statistically validates the consistency with which the logging codes have been applied at Plutonic for the last four years, with respect to both Au distribution and other elements. In doing so, we have developed a schema that allows objective logging to occur once core has been sent for assay and analysed by pXRF. While far from replacing the geologist in the field, this is a complementary method that adds significant value to a data set.CITATION:Gazley, M F, Tutt, C M, Latham, A R, Duclaux, G, Fisher, L A, Taylor, M D, de Beer, S J and Atkinson, K, 2013. Objective geological logging using geochemical multi-element data - Plutonic Gold Mine, Western Australia, in Proceedings World Gold 2013 , pp 455-462 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G Zhao, S Hapugoda, E R. Ramanaidou, P Hapugoda, Y Jin, G O’Brien

In 2021 the ports of Port Hedland and Dampier in the Pilbara Region of Western Australia handled 900 Mt of iron ore. This ore was produced in the Hamersley’s mines and transported by trains to the ports for subsequent export. Dust, which is generally considered to be particles less than 100 μm in diameter, is generated at all steps in the supply chain. Whilst all dust may have potential impacts on human health and mangroves and buildings a proportion of the dust is classed as respirable (PM10) dust, which consists of particles <10 μm in diameter. In 2021, in response to the community concern with iron ore dust, CSIRO commissioned an internal study to characterise and benchmark the dustiness of the different ores and to develop targeted strategies to minimise dust impacts, without affecting other iron properties, such as stickiness during transportation. A specific concern is that that the dust in the PM10 fraction may contain significant amounts of particulates, such as free silicates which may have health implications for the workers and residents. This study provided detailed mineral and chemical characterisation of the dust generated from the railed fine ore products for five generic Australian ore types: Australian Channel iron Deposit (ACID), Australian Brockman (AB), Australian Marra Mamba (AMM), Australian Pilbara (AP) and Australian magnetite (AM). The dust from these fine ore products were compared to that generated from a sample of Brazilian Hematite (BH) type ore fines. The ores were evaluated for their physical, chemical and mineralogy properties, dust generating potential and understandings of the relationship between the dustiness of iron ores and their physiochemical properties. The size distributions of the railed fine ore products were determined and a suite of analyses were conducted on subsamples of total (-106 μm) and fine (-38 μm) dust. For all the ores, the total dust fraction contains less Fe and more contaminants (SiO2 and Al2O3) than did the bulk ore. The fine dust fraction contained even less Fe and more contaminants (SiO2 and Al2O3) than the total dust fraction. This suggests that the iron ore dust contains more clay and potentially free silica than does the bulk ore. These findings were supported by optical and Scanning electron microscopy analyses of the samples. Dustiness measurements were made for each of the different ores (-106 μm) to investigate the relationship of dustiness of various iron ores with their physiochemical properties and assess their responses to dust suppression by the application of water sprays.

Sep 18, 2023

By Randall Morris

After years of steadily declining employment and production, the U.S. coal industry is having a moment. In 2016, when Donald Trump was running for U.S. President, he cast a spotlight on coal mining in his campaign speeches, promising to end the “War on Coal.” Fast forward to 2025. On the first day of his second term, President Trump signed the National Energy Emergency Act, which emphasizes domestic energy production as a matter of national security and focuses on incentivizing domestic energy resources. Then on April 8, President Trump issued an executive order opening federal land to coal mining to reinvigorate “America’s beautiful clean coal industry.” As the nation seeks to identify reliable solutions to meet its ever-growing energy needs, the administration is going all in on proven, reliable and readily available natural resources, including coal. This means the coal industry is positioned to play a pivotal role in the administration’s stated energy policy, and highwall mining could be an integral factor in helping the industry optimize the extraction of ore to make the most of this moment. The White House noted in a statement that the United States’ “abundance of energy and natural resources … have historically powered our Nation’s economic prosperity” and vowed to remove regulations that have hindered developing these resources — regulations that resulted in job reductions and higher energy costs for U.S. consumers, while weakening national security. “There has been an increase in electricity prices in the United States of over 30 percent in the past four years,” said Rich Nolan, president and chief executive officer of the National Mining Association (NMA). “This administration wants to focus on that, inflation and on increasing electricity availability to help lower the price over time by incentivizing energy policy. Coal is definitely a high priority for this administration.” Part of the White House’s strategy is to facilitate investment in coal-fired plants. The shift comes at a time when the reliance of coal-powered energy plants has been waning. According to the U.S. Energy Information Administration, 7.5 GW of electrical capacity from coal-fired plants was retired in 2024, following the retirement of 22.3 GW of electric generating power the two years prior.

Jun 1, 2025

By A J. Weston

Block or panel caving technology is far removed from that of the top slicing and block caving of the late nineteenth or early twentieth centuries. The rapid mechanisation and expansion of these methods in the late twentieth century was as much a result of the change of the technology of the unit operations of development, ground support, drilling and blasting and transport as it was of the advances in geotechnical understanding and practice. The small footprint gravity and scraper block caving mines with boundary weakening, rail transport and shaft hoisting of the early to mid-twentieth century have been replaced by massive high lift panel caves using preconditioning of the ore, large load-haul-dump units, adjacent crushers and conveyors to surface. The technology changes in the unit operations are described and the drivers for these changes examined.CITATION:Weston, A J, 2016. The evolution of block caving technology, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 265–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Michelle Stokes, Alexandra Miller, Campbell McKenzie

"The ancestral Ringarooma River in northeast Tasmania has transported alluvial tin and other heavy minerals from their onshore source of stanniferous Devonian granites downstream into what is now Ringarooma Bay. Previous exploration work has demonstrated the presence of potentially economic tin mineralisation within the palaeochannels and terraces associated with the submerged river.The offshore tin resource lies directly on the seabed or with less than 2 m of overburden, and within 5 - 50 m water depths in the wider bay area. The main river channel continues offshore for at least 13 km, with high tin grades found within the palaeochannel but also dispersed across the sea floor as a sheet wash, a result of Quaternary sea level change reworking the placer deposits. This drowned portion of the coastal plain contains a continuation of rich tin leads as low gradient anastomosing channels, and has been delineated by marine seismic and drilling activity since the 1960s. Tin grades in the Tertiary and Quaternary alluvial profiles vary from 50 - 300 g/m3, with the highest concentrations in the coarser basal horizons. A previous offshore explorer estimated a resource of 194 Mm3 at 150 - 250 g/m3.Kenex Ltd created 3D models of the paleochannels and the mineralisation with the aim of better constraining the resource estimate and identifying additional depositional areas. The modelling was undertaken with the input of geophysical data, bathymetry and geochemical sampling of the seabed surface and from historic offshore drill holes. A prospectivity model covering Ringarooma Bay was produced to target tin-bearing gravels. Predictive maps were created to represent various features of the offshore mineral system, including assessing gradient changes in palaeochannels and their sinuosity. The model identifies areas with higher potential for alluvial tin mineralisation and will be used to focus the exploration programme over tenements currently held by Kenex Ltd."

Sep 1, 2014

By David A. Benjamin

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 24,600-acre Orejana Canyon Wilderness Study Area (OR-001-078), in order to evaluate its identified mineral resources. The study area, located in Harney County, 76 mi northeast of Lakeview, OR, is underlain by Miocene basalt, rhyolite flows, tuffs, and tuffaceous sedimentary rocks. No mines, prospects, or claims were found within the study area. According to the U.S. Bureau of Land Management, the tuffaceous rocks have a moderate favorability for the occurrence of diatomite and a low favorability for zeolite resources. Also, the rhyolite flows have a low favorability for the occurrence of perlite resources. However, U.S. Bureau of Mines&apos; studies indicate that no metallic or nonmetallic resources are present in the study area.

Jan 1, 1987