Search Documents

In the March/April 2006 issue of the Journal, we published an ethical dilemma called “Blowing the Whistle.” We received many interesting responses to the article as requested. Some of the responses are printed here. We’ve also included “Blowing the Whistle” again in this issue as a refresher on page 37. Dear Editor, It is in my own personal belief that it would be extremely important if I were the blaster to take the following steps. 1. Hold an immediate emergency meeting with the contractor to convince them to stop work at this point.2. This meeting would need to be held with all powers that be in this construction company. This helps eliminate the hearsay (excluding the farmer). 3. Explain the entire situation to the contractors as it has been presented to the blaster by the farmer. 4. Recommend calling in an engineering or geological firm with the expertise to investigate this matter immediately, and take all immediate action based on findings. 5. Follow up with farmer allow him to speak, (a.k.a. vent) and assure him proper steps are being taken to come to resolve this matter. 6. Be a good listener, and communicator with the farmer while investigation is being conducted. 7. Should the contractor not want, or take any of these recommendations, the blaster himself and his company should question even working for this company ever again. This in itself would not be the class of people we would want to be associated with EVER.

Jan 1, 2007

By James C. Scott

Compression and tension load testing were performed on bored concrete piles installed to depths of 18 to 34 meters below excavation levels for a large mixed-use development in Kuala Lumpur, Malaysia. The 900 mm diameter piles were installed in weathered graphitic schist bedrock. Load testing confirmed the side shear and end bearing capacities of the piles. The work formed part of the investigations for the 56,000 m2 site which includes a 79-story office tower, hotel tower, apartment tower, retail complex, and plaza area underlain by 4 to 6 basement levels. The paper provides the results of the site investigations, pile-load testing procedures, pile-load settlement behavior, and shaft load distribution.

Jan 1, 2007

By T. C. Eisele

The use of column flotation was considered for the ?reverse flotation? of iron ore, where the gangue (quartz) was recovered in the froth product. This use of the froth for carrying the gangue mineral rather than carrying the valuable concentrate significantly changes the operational requirements of the column. The objective of this work was to determine which of several column flotation technologies would be most suitable for this type of flotation operation. Studies were carried out using both the Jameson column and the Deister column. Comparative results are presented that show the capabilities of both column types in this application relative to conventional Wemco flotation cells. Columns were demonstrated to have grade-recovery performance superior to what could be achieved with conventional cells. Two-stage flotation with the columns could produce a concentrate that was up to 70.2% Fe at 87.5% iron recovery, compared to 70.4% Fe at only 77.7% iron recovery for four stages of flotation in conventional cells. It was shown to be particularly important to operate the columns to recover a maximum of the quartz gangue into the froth. It was noted that there are often problems in scale-up of laboratory columns to plant scale, because the increase in height and the decrease in the ratio of height to diameter at the larger scale allows more axial mixing and bubble coalescence, both of which degrade the column performance. Horizontal baffling was shown to improve column performance by reducing axial mixing and breaking up large bubbles, and so the use of such baffles in the reverse flotation application was investigated.

Jan 1, 2007

By J. Piper

Markets and Production Beryllium (Be), an extremely light metal, is used in many specialty applications. It the lightest element in Group 2A of the periodic table, with a specific gravity of 1.85 gm/cc, and a high melting point of 12850C (Calvert, 2004). The functional properties of beryllium are stiffness, strength, dimensional stability, resistance to corrosion from acids, and electrical and thermal conductivity. The ability to reflect neutrons and transmit x-rays, makes beryllium irreplaceable in uses such as precision optical components, inertial guidance systems, and in nuclear reactors (Anon, 1993). Beryllium is used in Cu alloys to strengthen and reduce corrosion in copper wire, and in lightweight oxide ceramics that are used as heat sinks, and as electrical insulators. The market revenue of beryllium can be broken down into the seven major groups below, and are plotted on the pie chart in Figure 1 (Anon, 2005). 1.) Telecommunications & Computer 2.) Magnetic & Optical Data Storage 3.) Aerospace and Defense 4.) Automotive Electronics 5.) Industrial Components 6.) Appliance, and 7.) Other.

Jan 1, 2007

By D. Allen

Faced with decreasing ore grades and harder ores, many mines today are forced to become more efficient with their approach to processing. Variability in ore hardness, mineral liberation, reagent consumption, sliming, and leach responses are all a function of the minerals present and their concentration. Modern semi-automated X-ray Diffraction (XRD) analyses using Rietveld refinement techniques, in conjunction with high speed quantitative Near Infrared (NIR) analyses, provide reliable quantitative mineralogical ore profiling. By the implementation of XRD with NIR, mining, milling and leaching operations no longer need to be dependant on visual estimates for GeoMetallurgical Modeling and are provided with a valuable forecasting and production control tool. This paper will illustrate the development, plant implementation and application of XRD and NIR at several copper operations.

Jan 1, 2007

By Richard Short

Shallow rainfall-induced landslides in residual and colluvial hillslopes and steep embankments are a common occurrence in many settings [1, 2, 3]. While occasionally posing a threat to property and life-safety, they more often present an ongoing maintenance problem and can lead to the initiation of larger failures. Typically, these slides consist of 2 to 4-foot thick translational movements of silty and clayey soils down slope through the reduction of strength from increases in pore water pressures. Direct surficial infiltration and indirect groundwater seepage are the normative triggers for failure. In the residential community of Blackhawk, California, located east of the San Francisco Bay, these types of landslides are a common occurrence (Figure 1). However, shallow landslides have also been a repetitive and constant problem along many state highways where steep embankments have been constructed in close proximity to busy thoroughfares. Given the real threat to property values in residential and commercial settings and the constant maintenance problem posed to lifeline structures such as utilities, roadways, and pipelines, new methods to deal with these landslides are needed.

Jan 1, 2007

By Dale Preece

In the late 1970’s and early 1980’s substantial resources were devoted to research focused on producing oil from the vast oil shale reserves in the western United States. Since the oil is solidified in the pore space of the shale, extracting it in production level quantities presented monumental technical challenges. Major advances were made in the methods used to extract oil from the shale in large quantities. Extraction methods evolved to culminate in the underground in-situ retorting process. In-situ retorting relied on explosive blasting of the shale to fragment the rock and induce sufficient porosity and permeability for a burn front to propagate through the oil shale. That burn front consumes some of the oil and liberates a substantial portion of it (~30%) for collection and further processing. Oil shale retorting is a blasting intensive process where the entire retort is rubblized in one very large, delay timed blast. Retort 7 in Western Colorado consumed 540,857 lb of slurry explosive to rubblized 348,940 tons of oil shale. Current rock blasting fragmentation predictive capabilities have evolved substantially since these retorts were designed and tested. It is the purpose of this study to simulate the explosively induced fragmentation of oil shale using state-of-the-art computer codes and material models and to infer retort design implications for future development.

Jan 1, 2007

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

Jan 1, 2007

By H. Gumede

The occurrence of fracturing due to high stress levels is a major factor in hangingwall stability in deep level gold mine stopes. However, rock falls cannot be the result of these fractures alone. Rock falls can result only from the occurrence of unstable rock blocks defined by the interaction of the stress induced fractures and naturally occurring geological planes of weakness. These planes include bedding planes and joint set planes. However, there is a general lack of information on the characteristics of these planes (orientations, spacings and lengths)?it does not appear that any such systematic and quantified information, if collected, has been published. To remedy this situation to some extent, joint mapping exercises have been carried out in several geological environments in two gold mines. The data collected on joint geometry included orientation, spacing and length, and this information is included in the paper. In addition, the paper describes the use of the data collected to evaluate the potential for rock falls and the probability of failure of stope support

Jan 1, 2007

By N M. Vegter, C B. Kohler, E H. O Meyer

Zincor operates four Lurgi fluidised-bed roasters at its roast-leach-electrowin refinery in Springs, South Africa. In 2006, Zincor?s four roasters had reached ages ranging between 26 and 38 years, while the expected life of this type of roaster is generally 20 to 25 years. Based on its condition, Roaster 3 was the first to be rebuilt in 2006. Roaster 4 is being rebuilt in 2007 and the last two roasters will be rebuilt over the next few years as necessary. The main damage to Roaster 3 was caused by buckling of the roaster steel shell. This caused the freeboard and dome areas to shift, resulting in cracks in the dome brick lining and crumbling of the bricks lining the freeboard. The steel shell buckled due to the combined effects of too-high operating temperatures and corrosion caused by the following two main factors: ? Thicker external insulation was installed during a previous maintenance shut which resulted in and increased steel shell temperature and exacerbated the normal metal fatigue; ? SO2/SO3 containing gas that had permeated through the brick lining, passed through its dew point during frequent planned and unplanned shuts over the life of the roaster. This caused acid formation between the refractory brick lining and steel shell, resulting in corrosion of the shell. The initial plan was to replace only the damaged areas of Roaster 3, but upon dismantling more damage was found and the roaster was rebuilt from the tuyeres upwards. During the rebuild, the opportunity was taken to modify the design of some of the brickwork to extend its life and make future repairs easier. This paper discusses the mode of failure of Roaster 3 and the lessons learnt during its dismantling and rebuilding.

Jan 1, 2007

By Timo Niitti, Sami Grönstrand

n today's marketplace with high metals prices, many operations are faced with the challenge of improving recovery and at the same time maximizing availability. New operations under feasibility studies have the same requirements, with the additional need for ever higher capacities. Economies of scale have proved a vital competitive advantage in the game of ore dressing. Flotation is the most widely used method for extracting valuable minerals from ore - despite its mature age of 100 years. Customer demand has driven the development to increasing cell sizes, and in most cases, this has brought the advantages of both lower capital expenditure and lower operational and maintenance cost. The challenge of scale up, however, is to meet the metallurgical performance requirements in the larger volumes. The paper outlines recent trends and developments in flotation technology, and presents new solutions designed to address the needs for increased capacities as well as improved performance. Whether the goal is to improve existing operations or to scale up new equipment, computer aided tools are playing a key role in shortening the development cycle and reducing costly trial-and-error tests in full scale. Using the new tools and validation thereof will be outlined, as well as the development principles behind the new solutions. Plant results and experiences with the new developments are presented and discussed in several cases around the world.

Jan 1, 2007

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By G. L. Smith

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2007

By M Castle, D Mendelawitz

The Marra Mamba iron ore in FortescueÆs Chichester Range project area occurs as a very flat dipping series of waste shale and iron ore beddings. These beddings vary from millimetre thickness to several metres. The ore material generally exhibits a moderate degree of competence when subjected to ultimate compressive strength (UCS) tests, normally failing at up to 60 Mpa. However, the strength of the beddings is markedly less when subjected to the tensile forces imposed by the cutting action of the surface miner. Two surface miners of differing age and sizes were tested over a period of almost three months. These machines produced a product that had not been subjected to dilution by blasting and of such a size that primary crushing is not required. The machines were able to cut all ferrous material presented to them with varying degrees of success. Material containing higher quantities of manganese were broken but caused catastrophic wearing of the picks. During the trial the volume of material produced by the two machines in various strength materials very closely matched the manufacturerÆs estimates. The major impact on costs per tonne related to the wear on bits, which in turn varied with the bit design and composition. Bit design and composition testing is continuing.

Jan 1, 2007

By X. Zhu

Establishment and monitoring of revegetation in areas affected by mining activities is quite often a difficult task. The efficiency of the scheme applied can be substantially improved by using simple adequate indicators so that progress and trends can be plotted, elucidated and assessed over time. Sustainable revegetation management indicators should take into account soil quality and area characteristics, as well as social, economic and political aspects. In the present paper an interactive prototype Spatial Decision Support System (SDSS) is presented. The system, based on methodological studies, has been designed to identify and interpret indicators that can be used for the evaluation of revegetation efficiency. It provides a platform for formulating indicators describing biophysical, socio-cultural and economic processes during the entire revegetation period. It integrates modular assessment, database management sub-systems and Geographical Information System (GIS). It is structured in a way that takes into account the project environment, soil quality, land characteristics, data acquisition control, output engines and spatial analysis. The output generates visual quality diagrams and interactive attribute quality maps that elucidate revegetation issues.

Jan 1, 2007

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameter like commodity price, mining or processing cost, stripping ratio, etc. The most important characterization of these push backs is that the innermost push back has the highest value per ton, the second innermost push back has the second highest value per ton, and so on. These nested pits are generated based on the best estimates of grade within a representation of the orebody in a three-dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion, grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduces a new algorithm that incorporates ore grade uncertainty during the pushback design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence. Keywords: open pit mine, push back, ore grade uncertainty.

Jan 1, 2007

By S. Devasahayam

Acid production or acid drainage is a major environmental issue that also has negative implications on the aquifer system surrounding the mine tailings area. The approach to controlling acid mine drainage involves physical and geochemical characterization that affect acid production. The material permeability determines the availability of oxygen, which is paramount in acid production in coal rejects, and varies with depth. In this paper the author presents the variation in oxidized pyrite/acid production with depth in black coal mine washery wastes. Chemical kinetic parameters and the diffusive parameters have been used to obtain the variation in oxygen content and the oxidized pyrite content with respect to the depth and time. Its dependence on porosity and moisture content is illustrated.

Jan 1, 2007

By Tim Brick, Peter Jewell, Stephen Thompson, Simon Morgan

The $980m (€750m) Dublin Port Tunnel, Europe’s biggest urban highway tunnel project, was opened in December 2006. The culmination of this immense scheme is set to transform the environment, mobility and road safety of Ireland’s capital city. This paper summarizes the key aspects of a project linking both sequential and parallel construction of individual tunnels and describes various approaches to bored, mined and pre-support cut-and-cover tunneling in a wide variety of ground types and depth of cover. Examples of innovative approaches to deal with structural and geotechnical problems while maintaining full operation of both road and rail traffic and the integrity of properties in a dense urban corridor are described.

Jan 1, 2007

By C. Wade, A. Swart, M. Dworzanowski

AngloGold Ashanti operate a pyrite flotation plant at their East Gold Plant, Acid Plant and Flotation Plant (EGAF) metallurgical complex within their Vaal River operations in the North West province in South Africa. The flotation plant feed is reclaimed pyrite rich tailings and the concentrate produced is used as the source of sulphur for the EGAF acid plant. The sulphuric acid produced is in turn used for the recovery of uranium at the Vaal River South uranium plant. The original flotation plant built in 1960 was based on the use of many small volume flotation cells and was becoming very expensive to operate and its age severely limited further operation. A decision was taken in 2005 to replace this plant with a new one based on fewer, larger volume flotation cells. This paper describes the benefits of using larger volume flotation cells in this new flotation plant when compared to the smaller volume flotation cells in the old plant. The benefits of the new plant include a smaller plant footprint, fewer flotation cells, fewer pumps, no distribution boxes, simpler piping, a greater flotation volume and a reduction in installed power. The saving in capital cost could not be quantified because of the age of the old plant. The savings in operating cost will arise from fewer operators, less maintenance and reduced power consumption. The new plant has not been in operation long enough to quantify the benefits in operating cost and metallurgical performance. However, recovery improvements can be expected given the greater flotation volume (increased residence time) and the installation of larger, more efficient flotation cells.

Jan 1, 2007

By C. Musingwini

An often overlooked factor in the analysis of mine layouts and schedules is technical operating flexibility (or tactical flexibility), mainly due to its nebulous nature. By glossing over technical operating flexibility the resultant mine layouts and schedules maybe suboptimal. The need to incorporate technical operating flexibility into the analysis and comparison of mine layouts and schedules is increasing in importance. The nature of technical operating flexibility is illustrated, previous work on valuing of operating flexibility reviewed, and a proposal made on how technical operating flexibility can be quantified for tabular reef mines by using a platinum reef deposit as a case study. Once technical operating flexibility has been quantified it becomes possible to explore its incorporation into the analysis of mine layouts and schedules and subsequent optimization processes. This paper is a revised version of a paper presented in the Proceedings of the Second International Platinum Conference, ?Platinum Surges Ahead? in 2006. The work described in this paper is part of a current PhD study at the University of the Witwatersrand. Keywords: mine plans, layouts, schedules, technical operating flexibility/tactical flexibility, ore availability.

Jan 1, 2007