Search Documents

By Han Yi

The coarse indium ingots produced by Shaoguan smelter contained a lot of impurities. In order to produce the high pure indium with the purity more than 99.99%, the appropriate refining processes were designed and the practice of combined application of Glycerin-KI process and electrolysis in Shaoguan smelter was introduced.

Jan 1, 2005

By H. H. Kellogg

The Process Fuel Equivalent (PFE) for nine different flowsheets for production of anode copper from sulfide concentrates has been evaluated and compared for a set of uniform conditions and a "standard" concentrate analysis. The processes considered are: reverberatory smelting, (wet-charge and hot-calcine charge), electric furnace smelting, Outokumpu flash smelting (2 versions), mom flash smelting, Noranda Continuous Process (2 versions), and the Mitsubishi Continuous Process. The energy required for the numerous processes auxiliary to the principal smelting processes-¬roasting, drying, air compression, gas handling, dust collection, slag cleaning, acid manufacture, etc.--are separately evaluated and incor¬porated into the process comparisons. The factors in process design that lead to important energy savings are: use of fuel rather than electric energy; use of oil or coal rather than natural gas; maximum use of oxygen enrichment of the process air; drying of charge before smelting, or, even better, drying and preheating of charge by partial roasting in a fluid-bed; recovery of waste heat from all major hot process gases.

Jan 1, 1976

By Yoon-Bong Hahn

A mathematical model has been developed to analyze and predict the reduction process of iron ore particles in a two-stage fluidized bed system. This model includes the effect of particle degradation to elucidate its effect on reduction of iron oxides. Although the particle degradation is dependent on kind of iron ores, it was found that eighty to ninety percent of overall degradation is occurred in the prereduction stage mainly due to thermal stress and volume expansion. The degradation of particles in the?final stage is not much, but is mainly due to interparticle collision and abrasion. It was also found that to obtain a target reduction degree, it is of great importance to control the bed temperature and the residence time of paarticles in R1 rather than in R2. Optimum range of residence time was 15-20 minutes in the prereduction stage; 30-35 minutes in the final reduction stage.

Jan 1, 1996

By Xuyang Liu, Xuewei Lv, Yu Zhang, Xiaolong Wu, Chunxin Li

Titanium nitride is a broad-spectrum specific functional material because of its many superior properties. Therefore, it is necessary to investigate synthesis methods of TiN and alloys containing TiN reinforcement. In the current study, with the increase of nitrogen gas pressure and the optimization of routine ball milling parameters, the conventional mechanical ball-milling method can be improved, the nanometers TiH2-TiN composite powder can be synthesized successfully in a shorter time. Nitrogen gas filled in ball mill jar in which the pressure was 0.6 MPa. TiH2 powder was milled under nitrogen atmosphere at a spinning rate of 250 rpm. The results show that the stable TiN is formed after grinding for 2.5 h according to the X-ray diffraction pattern. DSC (differential scanning calorimetry) curves also indicate that milled compound powder adsorbs certain nitrogen gas. The gas adsorbed in TiH2-TiN composite can exist stably below 200 °C.

Mar 1, 2017

By Yasuhiko Ito

"This talk is concentrated on the topics of compound film formation on the substrate electrode by interdiffusion of substrate element and electrochemically deposited species and/or by direct electrochemical implantation of the component element of the film into the substrate. As a typical example, electrochemical implantation of nitrogen atom into Ti metal to form TiN surface film is described. Another example is the formation of various kinds of intermetallic compound films including Ni2Y, Ni2Dy and Pd3 Y by the electrochemical implantation of lanthanoid elements into transition metal electrodes. By combining these two methods, Sm-Fe-N ternary material film also could be formed. The principle and application of the ""electrochemical implantation"" are discussed in detail.IntroductionGenerally speaking, surface film formation by molten salt electrochemical process can be divided into the following three categories:(i) single element film formation on the electrode by electrodeposition,(ii) compound film formation on the electrode by electrocodepostion of more than two elements, and(iii) compound film formation on the substrate electrode by interdiffusion of substrate element and electrochemically deposited species and/or by direct electrochemical implantation of the component element of the film into the substrate.This talk is .concentrated on the topics of category (iii), especially on the electrochemical implantation. Typical example can be seen in the electrochemical implantation of nitrogen atom into Ti metal to form TiN surface film. Another example is the formation of various kinds of intermetallic compound films including Ni2 Y, Ni2Dy and Pd3 Y by the electrochemical implantation of lanthanoid elements into transition metal electrodes. By combining these two methods, Sm-Fe-N ternary material film also could be formed. The principle and application of the ""electrochemical implantation"" are discussed in detail with examples above as well as other experimental results also obtained very recently in the author's laboratory."

Jan 1, 2000

By R. M. G. S. Berezowsky

Treatment of Hudson Bay Mining and Smelting Co. Ltd. (HBM&S) zinc concentrate in the Sherritt zinc pressure leach process produces a residue containing elemental sulphur, residual sulphides, precipitated iron species, si1ver and gold. Flotation of the residue recovers most of the elemental sulphur and residual sulphides to the concentrate, leaving iron oxides and bask sulphates in the tailings. The tailings also contain most of the sflver and some gold. Direct cyantde leaching of the oxide tailings (220 g/t Ag, 1.4 g/t Au) was capable of leaching most of the gold, but only a minor portion of the silver. This paper reports testwork, conducted by Sherritt on behalf of HBM&S, to define a process for a high recovery of the precious metals from the oxide tailings. A si1ver enhancement treatment, consisting basically of digestion of the residue with lime at 90°C to render the silver amenable to enhanced recovery by subsequent cyanidation, was selected as the most promising approach. Batch silver enhancement and cyanidation tests showed that treatment of the oxide residue with 80 kg/t CaO at 90°C for 1 to 2 h increased the silver extractability in subsequent cyanidation from <20% to 96%. A 96 h continuous miniplant test (1 kg/h solids feed rate), of a circuit including a silver enhancement treatment step followed by conventional cyanidation and carbon in pulp silver and gold recovery, confirmed metal recoveries to the carbon of 90% Au and 96% Ag. Reagent consumption rates were 1ess than 100 ?kg/t CaO and 5 kg/t NaCN.

Jan 1, 1990

By Levente Becze

The zinc bottom dross is obtained as a by-product from hot dip galvanizing operations and contains at least 92 % zinc, which is recycled mainly by pyrometallurgical processes. The overall costs of such a treatment, however, are often relatively high, and the very strict environmental protection regulations might also cause additional difficulties for the high temperature procedures in the future. Therefore, a novel hydro-electrometallurgical process has been developed in our laboratory, by which one can reclaim zinc of high purity, while attempting to achieve low energy consumption and making allowances for all the environmental restrictions. This aqueous processing technique, based on electrolytic refining in a cell equipped with anion-exchange membrane to separate the anode and cathode compartments, allows the indirect purification of the anolyte. Zinc is dissolved from the anode along with some of the impurity elements, while the intermetallic compounds (Fe-Zn, Fe-AI- Zn) are accumulated in the anode slime.

Jan 1, 2003

By Geoffrey Brooks, Mehedi Bin Mohammad, M. Akbar Rhamdhani

Molten alkali nitrates are used commercially as thermal storage fluids (HTF) for solar thermal electricity generation. Their range of operation is limited by the thermal stability and this limits the energy (steam-Rankine cycle) efficiency of these processes. In this study, the effect of atmosphere on the thermal stability of nitrates was investigated using simultaneous thermal analysis techniques (STA). The use of oxygen (O2) as a blanket gas was found to delay the decomposition point of the ternary NaNO3–KNO3–LiNO3 (13.23–57.14–29.63 weight ratio) mixture by 55 °C. By which operating range will increase 65 °C more compared to the binary solar salt. Higher heating rates increased the decomposition point but had less effect on premelting and melting properties. Nitrogen monoxide, and O2 evolution after melting indicates concurrent reversible reactions. Similar phenomena were observed for single and binary nitrates. The eutectic melting point of ternary nitrate obtained from the STA agreed well with FactSage eutectic composition prediction.

Mar 1, 2017

By Shengli Wu, Jiacong Zhang, Kai Gu, Bingjie Wen, Heng Zhou

In practical production process, the average of silicon content in hot metal (HM) of COREX process (the average is 1.58%) is obviously higher than that in blast furnace (the value is below 0.6%), which leads to an increase in the cost of steelmaking. In this work, the factors affecting and impact mechanism of silicon content in HM were investigated by statistical analysis using actual operating data. The analysis indicates that the fuel rate, binary basicity of slag and the temperature of HM are positively correlated with the silicon content, while the sulfur content of HM and binary basicity of burden are negatively correlated with the silicon content. On this basis, a back propagation neural network was developed to predict and control the silicon content in HM. All the findings of this work are useful for guiding and optimizing the COREX operation.

Mar 1, 2018

By Yi Tan, Kazuki Morita, Yaqiong Li

Molten Si-Al alloy, with the addition of Sn, was used for metallurgical grade Si purification by a low-temperature solidification method, with the aim of improving the recovery rate of Si. In this ternary melt, bulk Si was grown with a planar front by a directional solidification process under a well-controlled thermal gradient and growth rate conditions, thereby reducing the contamination of solvent metals. Effects of cooling rate, amount of Sn addition, and temperature gradient on the quality of bulk Si were determined. The criterion for constitutional supercooling for single-phase growth from multicomponent melts was employed to evaluate the growth process.

Jan 1, 2015

By Courtney A. Young

All cyanide species are considered toxic and can be found predominantly in industrial effluents generated by metallurgical operations. For example, cyanide&apos;s strong affinity for metals makes it favorable as an agent for metal finishing and treatment and as a lixivant for metal leaching, particularly gold. These technologies are environmentally sound but require safeguards to prevent water contamination. Various methods of cyanide remediation by separation and destruction are available, but certain methods are more effective than others depending on the cyanide species being remediated. Photolytic destruction is regarded as the one technique that is independent of the cyanide species involved. The destruction of various cyanide species by several photolytic techniques has been investigated for the past few years. A literature survey suggests heterogeneous photocatalysis with anatase (TiO,) should behave similarly to homogeneous photolysis with hydrogen peroxide (H,O,) since proposed reaction mechanisms for both processes involve hydroxyl radicals. However, experimental evidence on a suite of cyanide species suggests otherwise. A new mechanism for the photocatalytic destruction of cyanides, especially SAD species, is therefore proposed.

Jan 1, 1998

By Norbert Steiner

For the desulfurization of weak SO2 gas streams, Degussa developed a process using dilute H2SO4 solution containing H2O, instead of conventional gas scrubbing with all solid absorbent medium (limestone, MgO). The process is based on fast reaction of H2O, with SO2 yielding H2SO4 up to 70% strength, depending on off-gas temperature. Compared to the conventional systems with typically < 95% efficiency, independent on the raw gas SO2 concentration, residual SO2 concentrations of less than 20 mg/Nm3 can be easily achieved, corresponding to nearly 100% removal. These features render the H2O, process a very attractive, low capital cost technology to retrofit existing conventional desulfurization plants.

Jan 1, 1996

"Many industrial processes involve materials that are subject to temperature change and thermal stress. Examples range from the casting of large metallic products to the cooling and reliability of small electronic components. Thermally induced stress is a major concern as it can lead to material damage and product failure. Material properties, thermal and mechanical, and process conditions such as the size and location of a feeder in metals casting, or the power dissipation in a computer chip, will govern the magnitude of these stresses. Temperature may also be influenced by fluid flow, for example, the airflow over a computer chip in a laptop will govern the rate of heat extraction, hence the temperature gradients in the chip and the evolving thermal stresses.This paper provides details on the governing equations for heat transfer (temperature) and solid mechanics (stress), their degree of coupling, and the numerical techniques used to solve them. Three examples are discussed to illustrate the use thermomechanical modelling. These also provide an insight into the degree of coupling required between the equations. The first example, involves thermal cycling of electronic components where a prescribed temperature field is applied. As temperature is known, this example only requires the solution of the stress equation. The second example also involves the modelling of an electronic component where the temperature field is also calculated. In both of these examples, the stress calculation is dependent on the temperature field, but the temperature calculation is not dependent of the solution of the stress equation (one-way coupling). The final example provides details on modelling the metals casting process. Both the temperature and stress equations are solved but, unlike the previous two examples, in this case the temperature field is dependent on the results from the stress calculation (two-way coupling)."

Jan 1, 2001

By J. Howarth

Two electrochemical processing methodologies have been used to electrogenerate bromine-laden solutions for gold-leaching purposes. In the first process, a laboratory-scale cell in which the anode and cathode compartments were separated by a cation-exchange membrane was employed. The bromine produced by electrolysis of a 4% bromide solution was used to leach gold from a low-grade ore. The pregnant leach solution was then returned to the cell to recommence the cycle. High current efficiencies (90-93%) were maintained over six cycles. In the second process, an undivided hypochlorite generating cell (Chloropac"&apos;) was used to generate bromine from a simulated leach solution. Electrolyses were performed on a pilot-scale (100-150 gallons) with solutions containing different levels of bromide ion. The current efficiencies were also high (80-90%) and unaffected by the bromide concentration (over the range 2.5-5%) provided the electrolysis was run to low conversion « 15%). The Chloropac module was capable of delivering 0.6 kg bromine per hour at a power cost of $0.09 per kg. Using these figures, a detailed economic assessment for a 1000 metric tonnes (MT) per day gold ore processing plant was made. Electrolytic regeneration of bromine in a gold leach/recovery circuit dramatically improves the process economics over cyanidation.

Jan 1, 1991

By A. E. Isaacson

The U.S. Bureau of Mines is studying the effect of supercritical water, at 400&apos; C and 3,500 psi, and subcritical water, at lower temperatures and pressures, on mixtures of minerals and metals to determine the possible applications of water at high temperature and pressure for processing these materials. This research was conducted using a flow-through bench-scale system. Copper-bearing minerals studied were chalcocite, chalcopyrite, covellite, and cuprite. In general, mixtures of copper minerals and pyrite reacted to form bornite. Intermediate phases formed were chalcopyrite and digenite. Similar reactions occurred between pyrite and metallic copper. A mixture of chalcopyrite and pyrite was inert in supercritical water&apos;. The reaction between cuprite and metallic zinc yielded metallic copper. The cuprite was reduced by hydrogen generated by the reaction between metallic zinc and water. None of the reactions occurred exclusively in supercritical water, but also occurred in water at high temperature and pressure below the critical point. &apos;Experimental results did show that a dual-reaction process, consisting of solid-state diffusion and fluid transport, was occurring.

Jan 1, 1989

By Dong Hoon Han

The sulfation rates of magnesium oxide and calcium oxide (molar ratio 7:3) contained in calcined CMA ( calcium magnesium acetate) by SO2 were measured. The experiments were carried out in the temperature range 700 to 1100 °C and under the SO2 concentrations of 0.3 to I mol % (5 % 02). In the low-temperature range below 830 °C the reaction produced CaSO4.3MgSO4 and unreacted MgO, but no MgSO4 phase. The formation of CaSO4.3MgSO4 phase has a significant implication in that it allows the utilization of MgO for SO2 removal whereas the sulfation of MgO from conventional sources is so slow that it is of no practical interest. Thus, the calcined CMA can remove SO2 at lower temperatures than conventional SO2 absorbents and at a greater capacity. Above 950 °C only CaO reacts with SO2, but at a much greater rate than the calcined Ca(OH)2, which is one of the most reactive SO2 absorbents.

Jan 1, 1998

By Rainer Köster, Tobias Wagner, Markus Delay, Fritz Hartmann Frimmel, Wolfgang Ferstl, Wolfgang Höll

"The mobilization of contaminants from industrial residues like ashes from municipal solid waste incinerators in case of leaching is investigated world wide. In classical leach tests only soluble species are considered. In addition the geochemical behaviour of residues has to be completed by assessing the mobilization via colloidal particles. This transport is well known from natural aquatic systems. Quantification of aquatic colloids is associated with considerable difficulties, because they are often found in low concentrations and in a size distribution where small particles with diameters below 0.1 µm predominate. In the past years, the Laser-induced Breakdown Detection (LIBD) has been developed as a novel sensitive method for quantifying colloids. Column leaching experiments with directly coupled LIBD were used to quantify the release of heavy metals and colloids out of bottom ashes. Some typical colloid bound heavy metal concentrations in the leachate are in some cases exceeding the limits defined by German authorities. The LIBD with a flow-through cell allowed to assign absolute values to colloid size and concentration."

Jan 1, 2008

By R. Gampala

The consolidation of mom matrix composite monotapes occurs by the plastic (time independant) and creep deformation of monotape asperities. Past models of the process used seperate micromechanical analyses of the contact deformation by (rate independent) plasticity and power law creep (i.e steady state creep). These models are now used to simulate consolidation and to optimize/control consolidation process cycles so that the composite&apos;s microstructure is "steered" to, a user defined goal state. However, the models do not incorporate the sometimes dominant transient creep process and the instantaneous response of the plasticity mechanism causes finite discontinuities in the microstructure state vector field and therefore eliminates the possibility of using the powerful array of trajectory optimization schemes that all require continuous vector field for optimization and control. To overcome this problem, a inified creep/plasticity constitutive model that results in a continuous state vector field is used to rederive the contact deformation response during monotape consolidation. The contact blunting of a laterally constrained hemispherical asperity is first analyzed and its response represented by two coefficients; one relating the contact area to the blunting strain (C), the second, the mean contact pressure to the blunting rate (F).The C and F coefficients for this unified blunting problem are then obtained by finite element analysis, and detailed results presented for two composite matri-ces of topical interest (Ti-24A1-11Nb and Ti-6Al-4V).

Jan 1, 1996

By Farhang Hedjazi

Anglo Asian Mining have recently installed an industrial-scale UF/RO plant to treat process liquors from the integrated heap leach/agitation leach/ resin-in-pulp gold ore treatment facilities at their Gedabek gold-copper mine in Azerbaijan. The UF/RO plant is designed to treat 60 m3/h of leach solution to produce discharge quality water. The RO concentrate, which contains elevated concentrations of copper, silver and cyanide, is sent to the company’s SART plant for the recovery of the metal values as a precipitated sulphide concentrate and the cyanide, which is recycled to leaching. The new water treatment plant improves the sustainability of the operations at Gedabek by enabling replacement of fresh water input with RO permeate and safe discharge of permeate to the environment, during periods of excess water balance. The paper includes pilot plant data and early results from the full-scale plant.

By S. Fitzel

The Betts process for electrorefining of lead has been in operation since 1902 in the Trail Operations Metallurgical complex. The Betts process allows production of high purity lead in a single electrochemical step. Process improvements and plant expansions have taken place over the many decades of operation of this process which has proven to be robust, flexible, and capable of successfully treating a large range of anode bullion compositions. This paper reviews the history of the Betts lead electrorefining process, the innovations and quick industrial adoption of new discoveries that took place at the end of the nineteenth century. The process was first implemented in Trail Operations and integrated very well with metallurgical needs then and now.