Search Documents

By Kosei Morita, Osamu Nakano, Katsuhiko Nagai, Kazuhiro Mori

"The Sumitomo Toyo Smelter and Refinery commenced its operation in 1971 with three Peirce- Smith (PS) converters. “2 hot – 1 blowing” operation was practiced, that is one of two available converters was blowing and the other was standby in a hot state while the third converter was under repair. After several improvements, the stack time ratio reached around 90%; and processing 5 batches a day became possible.As a result of the expansion program of the Toyo smelter and refinery that started in 2001, the converter operation pattern was shifted from “2 hot – 1 blowing” to “2 hot – 2 blowing” with the installation of second converter blowers and an additional ladle crane.In 2005 a, the fourth converter was installed and “3 hot – 2 blowing” operation began. Also, with improvements experienced in the anode furnaces and the anode-casting wheel operation, today, the number of cycles has been increased up to more than 8.5 a day.The treatment techniques of fugitive gas containing sulfur dioxide from converter furnaces have been gradually reinforced, and the fixation rate of treated sulfur is currently being maintained at more than 99.9%. This paper introduces the operations described above, and the improvements in environmental management techniques for the Toyo PS converter operation."

Jan 1, 2009

By Kampe. S. L., Baker. Andrew H., Tony Zahrah

"Experimental heats of reaction for the formation of several Al3Ti + TiB2 intermetallic composite formulations have been determined utilizing bomb calorimetry. To overcome the kinetic constraints and achieve ignition in these formulations, a boron (B)/potassium nitrate (KNO3) initiation aid was incorporated within the blended reactant compact. The heat contribution from the initiation aid was regressed to provide estimates of the heat of reaction of the nominal formulations. Powder x-ray diffraction was utilized to identify the products of the reaction and discern any differences between the predicted equilibrium products of the formulation and the actual products.IntroductionReaction synthesis is a technique for the creation of ceramics, intermetallics, and in-situ composite materials [1]. Reaction synthesis is defined by its self, propagating mechanism, where the energy liberated from a localized reaction within a green powder compact is enough to carry the bulk reaction to completion. Achieving a self, propagating state can be achieved in variations of two primary methods of initiation: uniform volumetric heating and directional propagation [2].Uniform volumetric heating involves subjecting a green compact of the unreacted formulation to uniform heating in a furnace to encourage diffusion to initiate the reaction (Figure 1a) throughout the bulk material. Directional propagation utilizes a point heat source at one section of a green compact of unreacted formulation (Figure 1b). The localized exothermic reaction at one point in the compact then initiates the reaction in the section of the compact adjacent to it and fully propagates throughout the entire compact until completion. Initiation of the localized reaction is generally associated with the melting of the constituent with the lowest melting point, with instantaneous initiation of the reaction usually occurring close to that melting point [1]. This melting point can be high in some systems of interest, such as the titanium (Ti) and boron (B) system in equation 1:"

Jan 1, 2011

By Kazuaki Mita

There are various intermetallic compounds in the Zn-Fe system. We synthesized them at about 673K. A specimen was examined chemically and X-ray diffraction was applied to ensure the formation of intermetallic compounds. Material containing two phases was placed in a Knudsen type effusion cell and the mass spectrum studied to evaluate the vapor pressure of zinc. The thermodynamic properties of intermetallics was then evaluated through measured intensity.

Jan 1, 1999

By Jiann-Yang Hwang

The economic growth in new developing countries such as China and India has stimulated strong demands in basic materials such as steel. World steel production has exceeded the milestone of a billion tons a year recently. However, the blast furnace technology, which was invented in 1340 A.D., is still the fundamental route for today?s steel production. It is important to develop a new generation of steelmaking technology that can meet the society?s needs from the energy, environmental and economic standpoints in the 21st century. The new microwave and electric arc heating technology discussed in this paper provides a totally different mass and heat transfer mechanism from the conventional blast furnace technology and offers a great potential to meet our society?s needs.

Jan 1, 2006

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

The carbon composite brick is a new refractory used in blast furnace hearth and bottom. It caused wide attention due to its high thermal conductivity and low erosion by molten iron. In this paper, chemical constituents, SEM-EDS and X-ray diffraction were carried out in order to understand reaction mechanisms. A series of experiments of oxidation resistance characteristics were made. The oxidation mechanisms of carbon composite bricks in the presence of air were analyzed. According to the analysis on many experimental results, the oxidation process of carbon composite bricks under different temperatures were controlled by different mechanisms. In the condition of high temperature, SiO2 as oxidation product hindered the diffusion of O2, and reduced the oxidation loss of graphite in the internal.

Jan 1, 2015

By Xiaorong Liu

Interfacial emulsion generated in copper solvent extraction is an inhomogeneous O/W emulsion that consists of organic phase, aqueous phase and solid particles. In order to determine what kind of components in organic phase promotes the emulsion, the organic phase separated from the interfacial crud provided by Dexing Copper Mine in Jiangxi, China was analyzed for its components by combined gas chromatography-mass spectroscopy. It was found that many kinds of emphiphiles containing such hydrophilic groups as carbonyl, carboxyl, or acylamine existed in organic phase, most of which were originated from the reagent degradation. Conclusively, Lix984N would degrade gradually during a long-term contact with the acidic aqueous feed and strip reagents. Lix84 and nonylphenol, as effective components of Lix984N, degraded almost completely after long-term recycling. As a result, the effective components of Lix984N were far lower in concentration than the dense-aromatic impurities derived from the diluent and the degradation products in total. The degradation of Lix984N would deteriorate solvent extraction, disengagement performance and result in more serious interfacial emulsion.

Jan 1, 2006

By Alexander I. Raitchenko

"An electroconductive viscous liquid may flow in laminar or turbulent regime under Lorentz-force generated by the intercrossed electric current and magnetic field. When there is a starting flat layer between hard and free boundaries with surface tension the spatial Lorentz-force can create a specific stationary regime of flow: the plane free surface will transform into the wavy one, and the movement in the depth will be not laminar and not turbulent, but this regime will be characterized by organized forms with indications of ""rolling of long cylindrical drops"". Wave-length is determined by the viscosity, the density, the surface tension, the average thickness of layer, and Lorentz-force. ·The limit of wavy regime is determined by most long of wave which is directly proportional to the critical value of specific flow and inversely proportional to the kinetic viscosity. The proper critical value of Reynolds number is determined by the dimensionless combination containing surface tension, density, viscosity, and Lorentz-force. The mentioned dimensio.nless combination in our case is some criterion substituting the known Kapitsa number for case of the thin viscous liquid layers under gravity. Spreading of admixture by mechanism of wavy regime is more rapid than by common diffusion or by laminar flow. The suggested conception can be a contribution into the theoretical basis for elaboration of some specific liquid metals technologies."

Jan 1, 1999

By W. G. Davenport

Chapters 19 and 20 examine direcHo-copper flash smelting and flash converting. This chapter compares the two processes and suggests which is likely to be 'the more economic for a given concentrate. It: (a) uses Chapter 19's direct-to-copper industrial oxygen and oil requirements (b) adds the energy required for electric furnace recovery of Cu from direct-to-copper slag (Czemecki et al 1999) (c) combines Chapter 20's, flash converting calculations with Chapter 18's flash smelting calculations to determine their combined industrial oxygen and hydrocarbon fuel requirements (d) adds the energy required to granulate, crush and dry flash smelting matte for the flash converter (e) adds the energy required to granulate and dry flash converter slag for recycle to flash smelting (f) compares direct-to-copper and flash smelting/flash converting in terms of their total equivalent hydrocarbon ener.gy requirements.

Jan 1, 2001

By E. C. L. Cardoso

Hydrocarbon polymers, as PP, made from cheap petrochemical feedstock are important in many branches of industry. However, they have an undesirable influence on the environment and cause problems due to waste deposition and utilization. Polymeric materials composites account for an estimated from 20 to 30% of total volume of solid waste disposed. Thus, there is a tendency to substitute such polymers by those ones that undergo biodegradable processes. Polypropylene (PP) is a commodity, with high melting point, high chemical resistance, low density, with a balance between physical and mechanical properties and easy processing at low cost. Nevertheless, PP shows limitations for some special applications in automotive industry and civil construction. In order to minimize this deficiency, related to rheological behavior of polymer melt, especially referring to viscosity in processing temperature, a 50% mixture with HMSPP (High melt Strength Polypropylene) was used. PP/HMSPP was blended with 10, 15, 30 and 50% of natural (sugarcane bagasse) and synthetic polymers (PHB and PLA) aiming to partially biodegradable materials. The admixtures were subjected to gamma-irradiation at 50, 100, 150 and 200 kGy and then further assessed by mechanical tests in order to evaluate their degradability.

Jan 1, 2015

By Kai Kang, Jun Bao, Shouping Liu, Xiao Sun

Powder characteristics have a significant influence on selective laser melting (SLM) process. In this research, particle size, surface contour and the microstructure of IN718 powder used in SLM were tested, and the physical and chemical changes during heating process of the powder were investigated as well. The shape characteristic and fluid properties of IN718 powder were defined and measured. It is shows that most particles of IN718 powder exhibited nearly spherical shapes, and the particle size is about 22.95μm. On this basis, IN718 sample was fabricated by SLM process using the powder and the microstructure of the fabricated sample was investigated. The results indicated that the sample has a dense microstructure, no macro-defects but a few micropores and porosity. Compared with the powder, there was no new phase formed in the sample and melting point of the sample was little less than that of the powder.

Jan 1, 2015

By Roberto Parra, Roberto Parada

"A novel process for minor elements control in copper pyrometallurgical production is proposed based on a theoretical analysis and the results of an experimental program. Its application can solves operational problems related to volatile elements that determine pollutants gas emissions and the final quality of anodes. The process considers a calcination of mixtures of the dust with sulfidizing agents such as dirty copper concentrate or elemental sulfur at temperature under 800 °C. The product are a clean calcine that recovers all the Cu content on the dust and a gas stream that collect the minor elements as sulfides species. The calcine can be returned to the smelter avoiding the As increasing in the circuit and so on, the capacity for the treatment of dirty concentrates for the smelter can be higher. The possibility to apply vacuum in the calcinations step can decrease the operation temperature. The solid condensed from the gas has different options for its stabilization, with the advantage that this stream represents few mass with high As content.IntroductionThe control of undesired minor elements (IVIES) in conventional pyrometallurgical copper production is especially relevant for ore deposits associated to Andes region. The concentrates that are being produced present every time higher levels of volatiles and harmful elements: group Va (As, Sb and Bi), Pb, Zn, and Sn."

Jan 1, 2008

By Jun Miao, Kang Liu, Jilai Xue, Jun Zhu

CO2 emissions must be reduced by at least 50 % by 2050, and hence the technical solutions to capture and convert CO2 into value–added products should be considered. A Cobalt(III) Schiff base complex (Salen–Co(III)) has been investigated as a catalyst for synthesis of cyclic carbonate from CO2 and epichlorohydrin(ECH) with tetrabutylammonium bromide (TBAB) as co–catalyst. To recover Salen–Co(III) for the next cycling operation, it was immobilized onto zeolite 13X through excessive impregnation method. The immobilized catalyst was characterized using XRD, SEM, BET and ICP–AES techniques. Catalytic tests showed that yield of cyclic carbonate reached 90 % using 0.5 mol % Salen–Co(III) at ambient conditions. The immobilized Salen–Co(III) exhibited better catalytic activity than the homogenous one when used at the first cycle, but the yield decreased by some 20 % after five cycles.

Jan 1, 2015

By Dai Xi

In the present work, the viscosities of molten FenO-MgO-Si02 and FenO-MgO-CaO-Si02 semi-synthetic slags for nickel flash smelting were measured in the temperature range from 1473 to 1723K by a rotational viscometer. The ratio of Fe to Si02 was fixed at 1.2, calcium and magnesium oxide contents varied in the range from 2 to 8 mass% and 9 to 12 mass%, respectively. The results showed that silicate anions became smaller by increasing CaO content, which results in a decrease of the viscosity of the slag. In the case of MgO addition the viscosity behavior was complicated. At MgO content below 11 mass%, the viscosity increased with the increase of MgO at all temperatures tested. However, when the MgO content was above II mass%, the viscosity decreased slightly for FenO-MgO-CaO-Si02 system. At higher MgO contents, low-viscosity slags can be obtained by adding CaO. At a given composition, the viscosity decreased with increasing temperature. The higher the temperature, the more MgO can be added before saturation. The effect of Fe304 on the viscosity was quite significant. The viscosity of slag increased by 300mPa's at l573K when Fe304 content varied from 3 to 9 mass%. The viscosity values are presented as the functions of temperature and composition. A comparison between FenO-MgO-Si02 and FenO-MgO-CaO-Si02 systems is given in this study.

Jan 1, 2003

By R. Winand, M. Degrez, C. Temmerman

"The influence of the copper electro crystallization inhibitors (mainly thiourea, gelatin and chloride ions) is studied in a new fully automatic pilot plan. This paper describes the conception and the building of this plan. The new approach is to reproduce the experimental conditions observed in the industry with the three additives present simultaneously in the electrolyte and secondly to study the influence of a slight modification of the concentration of one inhibitor, the others being present in the electrolyte with their industrial nominalconcentrations.1. INTRODUCTIONDespite the fact that gelatine, thiourea and chloride ions have been used in copper electrorefining for a long time, precise knowledge concerning their influence on the cathode deposit, metallographic structure and associated properties is still lacking.Many authors studied the influence of each additive separately, or of two added at a time. Only a few authors studied the combined influence of the three additives added simultaneously. The general conclusion that can be drawn is that the combined influence is far from that forseen from the influence of each additive separately, or even from two additives used at a time. Moreover most of the experiments described in the literature were performed by adding all additives at once initially. It is however, well known that gelatine looses a great part of its activity during the first half hour due to degradation by sulfuric acid (as shown by the cathode overpotential drop). Thiourea is rapidly replaced by a number of degradation mole,cules and complex ions including cations from the solution, changing even the equilibrium between Cu, Cu(I) and Cu(II).Chloride ions are consumed by precipitation.A number of successive research projects [1-9] led pregressively to the concept that, in order to obtain reproducible results representative of industrial cathodes, it was necessary to simulate as far as possible industrial conditions. It was essential that all additives were added continuously during the electrolysis, with, as consequence, a continuous bleed.The purpose of this paper is to describe the concept of a new fully automatic pilot plan for copper electrorefining and to present the first results."

Jan 1, 1997

By Mike Santaluce

Smelting furnace rebuild projects often require a significant capital expenditure and an extended smelter outage. Smelter operators are increasingly searching for methods and initiatives to shorten furnace rebuild schedules, maintain manageable cost levels, enhance furnace performance and achieve excellent safety results. This paper describes the ?MEPC? Model for furnace rebuilds; a project driven approach which Auburn has developed in response to the need for improving furnace rebuild project outcomes. The ?MEPC? (Management, Engineering, Procurement and Construction) approach better addresses the unique challenges presented by furnace rebuild projects when compared to the traditional EPCM (Engineering, Procurement, Construction Management) model widely in use for these projects today. One key feature of the MEPC model is that a dedicated project management team with representation from all of the major project stakeholder groups is put in place at the onset of the project. The project management team has ownership and accountability for meeting overall project goals over the entire lifecycle of the furnace rebuild project. A second key aspect of the model is emphasis on project management as a completely separate project function with its own specific skill sets, techniques, tools and best practices. These features of the MEPC model offer several advantages in terms of improved planning, coordination, communication and alignment with project goals which contribute to the overall success of furnace rebuild projects. Similar MEPC concepts have been used to deliver excellent project results in other industries and the MEPC approach has been successfully utilized on furnace rebuild projects.

Jan 1, 2006

By H. -P. Behrendt

Muldenhiütten Recycling und Umwelttechnik GmbH is a lead smelter with a very long tradition. The first reference to the existence of smelters on this site is given by a document of inheritance dated 1318. Originally run as a primary lead smelter, which was supplied with ores from the Freiberg mining district and from overseas, it was required to change it over to secondary raw materials due the abandonment of mining in the Freiberg area in 1968. Today, Muldenhüitten Recycling und Umwelttechnik GmbH has two production lines; lead production from secondary lead and waste incineration, which are closely connected and gain advantage from each other. Installations, improved technologies, and the highly skilled personnel have contributed to satisfy all demands for a production concerning quality and environment.

Jan 1, 2000

By Bin Xu, Qian Li, Ya-xuan Wang, Yong-bin Yang, Xi Zhang, Tao Jiang

The effects of common associated sulfide minerals including pyrite, arsenopyrite, galena and sphalerite on thiosulfate leaching of gold were studied in this work. Sulfide minerals had significant effects on gold leaching because that the dissolved products of sulfide minerals precipitated on gold surface to form coating layer. The degree of sulfide minerals impact on gold dissolution decreased in the order of pyrite ≈ galena > arsenopyrite > sphalerite, while the degree of effects on thiosulfate consumption decreased in the order of pyrite > arsenopyrite > sphalerite > galena. The additive CMC (Carboxymethyl cellulose) could not only reduce thiosulfate consumption but also increase gold dissolution. The mechanism of this might be that CMC could restrict the decomposition of thiosulfate by cupric ions and the precipitates on gold surface.

Jan 1, 2015

By Yang Wang, Xiancong Zhao, Hao Bai, Qi Shi, Zhancheng Guo

Linz-Donawitz converter gas (LDG) or basic oxygen steelmaking gas (BOSG) is one of the most important secondary energy sources in iron and steel industry, whose effective use plays a vital role in energy saving and emission reduction. However, the generation of LDG suffers from great fluctuation with respect to the production status of steel making. Therefore, a long term prediction model of LDG generation would be essential in gas system balancing and optimization. In this paper, a long term prediction model for the generation volume of LDG was proposed based on the steelmaking production estimation from Gantt chart and k-means clustering algorithm. Compared with the previous model, this model considered the influence of different steel type on LDG generation. The experimental results of a steel plant demonstrate that the proposed model exhibits high accuracy and can provide an effective guidance for balancing and scheduling of byproduct gases.

Jan 1, 2016

By Hiroyuki. Fukuyama

The pseudo-binary phase diagram of the cuspidine (3CaO2?SiO2?CaF2) - CaF2 system has been studied by electron probe microanalysis (EPMA) and X-ray diffractometry (XRD). To prevent fluorine loss in the form of a HF gas by a reaction of CaF2 with water vapor at elevated temperatures, the equilibrium experiments were conducted with the sample hermetically sealed in a platinum tube. By employing this technique, it was successfully revealed that cuspidine exists as a stable phase and congruently melts at 1684 ± 1 K, and the cuspidine - CaF2 system presents a simple eutectic type of phase diagram, of which eutectic temperature has been estimated to be around 1540 K, corresponding to the composition of 40 mass% 3CaO?2SiO2 - 60 mass% CaF2?

Jan 1, 1999

By Toshiyuki Nohira, Eiichi Takeuchi, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The Dy-Nd-Pr-Ni alloy sample was prepared by cathodic potentiostatic electrolysis at 0.65 V (vs. Li+/Li) for 1 h using a Ni plate in a molten LiCl-KCl-DyCl3-NdCl3-PrCl3 system at 723 K. The highest mass ratio (Dy/Nd+Pr) in the alloy sample was observed to be 50 at 0.65 V. Anodic potentiostatic electrolysis at 2.20 V for 12 h was conducted using the Nd-Fe-B magnet electrode in a molten LiCl-KCl system. All elements were almost dissolved from the magnet, and the original form of the magnet disintegrated. After anodic potentiostatic electrolysis at 2.20 V, cathodic potentiostatic electrolysis was conducted at 1.00 V for 5 h using a Mo plate in order to remove the dissolved Fe from the bath. Finally, cathodic potentiostatic electrolysis was conducted at 0.65 V for 12 h using a Ni plate. The mass ratio of Dy/Nd in the alloy sample was determined to be about 18.

Jan 1, 2015