Search Documents

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999

By Halvor Dalaker, Alain Marc Ferber, Thor Anders Aarhaug, Pål Tetlie

Off-gas monitoring of experimental reactors give little information about intermediate reaction products and reflect chemical equilibria at reduced gas temperatures. A reactor design with optical access was designed and tested in order to be able to qualify and quantify gaseous species from their emission spectra. By use of a sequence of sapphire, UV fused silica and IR transparent sapphire and CaF2 windows and lenses optical access to a hot, maximum 1800 °C, reaction zone was gained. A cooled area behind the reaction zone was used as a background in order to avoid signal saturation from reactor walls. In addition to molecular emission spectra, atomic emission lines are used to characterize stable gas constituents and radicals. The setup has been designed for the study of methane dehydrogenation experiments in order to investigate the carbon activity of reduction of oxide with methane, but has also been used to monitor gaseous silicon suboxide.

Jan 1, 2015

By P. R. Taylor

Diamond films have been successfully formed in an inductively coupled plasma (ICP) chemical vapor deposition (CVD) system from several gas mixtures: CH,-H,, C2112-112, and C2112-112-02' Our previous thermodynamic study indicated that the substrate temperature could be lowered by the presence of oxygen species at moderate system pressures (0.3-0.5 atm) and that higher volumetric growth rates required a high temperature source and a moderate pressure system in CVD processing. The principal experimental results were consistent with the thermodynamic predictions. The deposited films were characterized by laser Raman spectroscopy, scanning electron microscopy, and X-ray diffraction. The films were well faceted and uniform, with the growth rates over 10 pm/hr on molybdenum substrates. The crystal size ranged between 1 and 2 microns for a two hour experiment. It was possible to decrease the substrate temperature to below 800 °C in this system.

Jan 1, 1995

By E. Açma

In this study, the production of Cu, Co, and magnetic iron oxide from the ancient copper, slags, located in Küre-Turkey, is investigated. In the process under development, fayalitic slags containing 1% Cu, 0.43% Co are reduced in a D.C. arc furnace with coke or graphite additions. A metallic alloy, consisting of 3.8% Cu, 3.3% Co, 2.1% S, and the rest being Ice, is produced by granulation of the liquid metal. About 85% recoveries of Cu and C:o are achieved by hot sulfuric acid leaching of these granules followed by H2S precipitation. The, production of magnetic iron oxide is possible from the discarded leach solution, loaded v:ith FeS04, by using a method with geothite precipitation, dehydration, controlled reduction, and re-oxidation steps. The magnetic oxides produced have 20 m2Jg surface area, 1:8.3 aspect ratio, and the coercivity of 330-380 Oersted.

Jan 1, 1993

By Denise C. R. Espinosa

The amount of secondary batteries are increasing about 15% by year. Among these batteries, it can be highlighted the NiCd ones, due to their high consumption. In Brazil, the consumption of NiCd batteries grown quickly in the last 5 years, due to the dissemination of cellular telephones and other electronic devices. The first step of a process to recycle spent NiCd batteries is the pretreatment through unit operations of mining treatment. The aim of this work is to define a physical pretreatment to conditioning the waste to a pyrornetallurgical recycling process of spent NiCd batteries used in cellular telephones. Batteries were disassembled by hand to release the different components. The studied batteries are basically composed (by weight) of: 78% nucleus, 18% plastic case and 2% circuits. The grinding of the batteries was performed by knife mill and also by hammer mill. After grinding the material was screened and submitted to a magnetic separator.

Jan 1, 2001

By Bart Blanpain, Tom Peter Jones, Muxing Guo, Liugang Chen, Huayue Shi

Fayalite based slag is formed during the smelting process of secondary copper resources. It was found that with the presence of high ZnO, the slag became viscous, causing a slag tapping problem. In the present paper, the phase relations of the slag system ZnO-“FeO”-SiO2-Al2O3- CaO (ZnO = 0-12 wt%, Al2O3% = 0-15 wt%, CaO = 0-1.5 wt%, with iron saturation) at 1150 °C is studied by using quenching technique followed by phase identification and compositional analysis of equilibrated samples. The dependence of FeO and Al2O3 solubility in the liquid slag on the chemical composition of slag is characterized. Based on the experimental data, the solid fraction of the slag, which may considerably, influences the slag viscosity, at the tapping temperature can be reasonably estimated and, therefore an appropriate modification of the slag composition can be made.

Jan 1, 2016

By Virgil Optasanu, Yvon Lacroute, Eric Lesniewska, Tony Montessin, Pauline Vitry, Eric Bourillot, Cédric Plassard

A general challenge in metallic components is the need for materials research to improve the service lifetime of the structural tanks or tubes subjected to harsh environments or the storage medium for the products. One major problem is the formation of lightest chemical elements bubbles or different chemical association, which can have a significant impact on the mechanical properties and structural stability of materials. The high migration mobility of these light chemical elements in solids presents a challenge for experimental characterization. Here, we present work relating to an original non-destructive, with high spatial resolution, tomographic technique based on Scanning Microwave Microscopy (SMM), which is used to visualize in-depth chemical composition of solid solution of a light chemical element in a metal. The experiments showed the capacity of SMM to detect volume. Measurements realized at different frequencies give access to a tomographic study of the sample.

Jan 1, 2015

By George Nekoksa

The biofilm activity monitoring probes measure applied current during intermittent short-term polarization of the probe electrodes and current or potential between the electrodes after removal of the polarization. The probe polarization mimics conditions at crevices, welds and inclusions where the biofilm activity and microbially influenced corrosion usually concentrate. Monitoring of AC resistance between the probe electrodes can provide infornation about the thickness of deposits.

Jan 1, 1994

By R. Dekkers

Non-metallic inclusions in liquid steel are mainly formed during killing. As far as these particles are not captured by the slag, they are found in the cast steel where they can deteriorate the mechanical properties. Inclusions may also disrupt the continuous casting process, affecting thus directly the quality of the steel and the production capacity. Steel pin samples from the Sidmar plant (Belgium) were taken in different steps of several ladle treatments and in the tundish. Also slab samples were studied. All samples concern the same type of low alloyed aluminium killed steel. The non-metallic inclusions were isolated from the steel matrix and investigated with scanning electron microscopy and energy dispersive spectrometry. The evolution of the non-metallic inclusions is described by their number, size, shape and elemental composition. The main non-metallic inclusions present are aluminium oxides and spinel type compounds.

Jan 1, 1999

By Gabriel Riveros, Ariel Balocchi, Andrzej Warczok, Daniel Smith

Blister copper from converting of copper matte is processed by fire refining prior to electrorefining. The fire refining consists of two steps: copper oxidation with impurities slagging and copper reduction. The classical batch process is carried out in vascular or reverberatory furnaces called anode furnaces. A new process for continuous copper fire refining has been proposed. The copper flows through two reactors in cascade, where is oxidized and reduced. The flow of a liquid copper through a ceramic packed bed increases the surface area and the rate of oxidation as well as the rate of reduction in the packed bed of charcoal. Mathematical modelling allowed for the design of a laboratory scale demonstration installation and industrial-pilot installation in Hernan Videla Lira Smelter (Paipote). The results have demonstrated the process feasibility and flexibility in operation.

Jan 1, 2009

"EAF dust is categorized as a hazardous solid waste. EPA approves only two treatment methods: either sending the dust to zinc recycling facility, or stabilizing it first and then disposing it to a specially-lined landfill. Both treatment methods are costly to EAF steelmakers. In order to reduce the cost and even better to make profit from the dust, EAF steelmakers need to find a costeffective technology to separate zinc from EAF dust. This paper is dedicated to discussion of a novel recycling strategy: in-process separation of zinc from EAF dust. The concept of in-process separation of zinc from EAF dust is first defined, and then a simple Zn concentration model is developed. From this model, two approaches of in-process separation of zinc from EAF dust are derived: (1) prematurely capturing dust at very high temperature when zinc is still in vapor status, (2) prematurely collecting dust immediately after quickly cooling EAF off-gas from high temperature to low temperature. Next, thermodynamic analysis is conducted to understand zinc behavior in EAF off-gas. It is demonstrated in theory that zinc is in vapor status while it exits from electric arc furnaces. At last, recycling routes and economics of in-process separation of zinc from EAF dust are discussed.IntroductionElectric arc furnace (EAF) plays an increasingly important role in steel production. According to USGS, steel production from electric arc furnaces has long exceeded that from basic oxygen furnaces [JJ. In 2009, electric arc furnaces produced 64% of total steel in the United States.Along with the fast growth of EAF steel production, generation of EAF dust is also rapidly increasing. A survey by AIM Market Research showed that 10 - 20 kg EAF dust was generated for every ton of EAF steel produced [2] In 1999, the United States alone produced 770,000 metric tons of EAF dust [3] In Europe, annual generation rate of EAF dust is more than one million tons [4-5]. In Japan, about 450,000 tons of EAF dust is produced each year [6] Globally, total generation of EAF dust was estimated to be more than 5 million tons per year [5] EAF dust is categorized as a hazardous solid waste since it often contains heavy metals, such as lead, chromium and cadmium. US Environmental Protection Agency (EPA) approves only two methods for treating EAF dust: (1) recycling the dust by EAF-dust recyclers, and (2) specially landfilling the dust for disposal after it is chemically stabilized. These two methods of treating EAF dust are both very costly to EAF steelmakers. It was estimated that a fee of $150 to $200 per ton of EAF dust was paid for various treatment options, which added approximately $2 - 3 cost for every ton of liquid steel produced by electric arc furnaces [?J."

Jan 1, 2011

By Jan Steinhoff

The design options of a gravity separator are still limited and rely on the study of settling behavior. A methodology will be presented where an experimentally given inlet droplet size distribution (DSD) is the basis for the calculation of the dispersion layer in a gravity separator. A pilot-scale continuous gravity separator is presented and CFD (computational fluid dynamic) results are validated. A transmitted light measurement technique for the determination of the DSD is presented up to a holdup of 15% dispersed phase. The resulting DSD was in the range of 20–2000 μm depending on flow rate and phase ratio. Furthermore, correlations of the real DSD with the settling behavior of the dispersion in a settling cell are discussed. The new approach to the description of gravity separators will be presented and the applied CFD methods showed good results with the system water/paraffin.

By Ma Shao Xian, Li Dong, Li Zhen Guo

"The new type shaft calciner ( SK-10 Serials) is developed and designed by CADRE itself on the basis of the conventional shaft calciner. The actual application in a number of calcinations plants have proven that they are of very good effect. Calcined coke calcining heated by the shaft calciner has a high quality, lower lost by fire. The shaft calciner needs no additional fuel when it is working. Anode Carbon Plant and calcined coke Plant commonly used the shaft calciner in domestic. The waste heat from the shaft calciner can be recuperated to generate electricity and to make the steam for produce. Exhaust waste heat is recovered by 90% or more. The new type shaft calciner's structure is optimized by computer simulation for fire-wall structure, combustion air to fuel ratio, volatile combustion is fully in use, furnace cooling zone structure, the exhaust smoking structure and calciner heat balance. Furnace structure and production operating parameters has been got the best optimized results. This paper introduces the working principle and characteristics of the shaft calciner - the equipment for calcining of the petroleum coke. It also demonstrates measured process parameters of the new type shaft calciner. Through comparison with the rotary kiln and conventional shaft calciner, it proves its own technical characteristics and advantages: higher capacity, high quality products, provides more energy for power generation, equipment operation and maintenance costs lower.IntroductionChina's petroleum coke market is mainly dominated by the delay raw petroleum coke. Rotary kiln and shaft calciner are the main process equipment for calcined petroleum coke. As the shaft calciner burning less, no external fuel, waste heat utilization is high, long service life, the utilization rate in China is more extensive than the rotary kiln."

Jan 1, 2012

By Carolina G. D. Ribeiro, Carlos Maurício Vieira, Jordana Ferreira, Sergio N. Monteiro, Janaina da S. Vieira, Cláudio R. Marciano, Natália de O. R. Maciel, Frederico M. Margem

One of today’s biggest concerns has been environmental issues, which has motivated researchers and the development of materials from renewable resources and environmentally friendly. Natural fibers have excelled in replacing synthetic fibers used in composites manufacturing, because natural fibers are biodegradable, abundance in the nature, low cost, low density, high strength, among others. Due to these qualities, some natural fibers are used for many purposes in automobile industry. However, the natural fiber has irregularities and pores in its structure which directly impact the density determination by geometric techniquesand, accordingly, the volume of fibers used in composites. Therefore, the main objective is this study is to determine the density of curaua fiber by pycnometry and to compare it with the commonly used geometric technique.

Mar 1, 2017

By S. W. White

Plasma arc technology is increasingly being used to process a number of waste materials. In present research, plasma technology is being investigated to treat waste magnesium baghouse dust, which is a waste material from the Magnetherm process. This dust contains mostly MgO, but also contains NazO, CaO, and KzO. Plasma energy is to be used along with a reducing agent to produce pure gaseous magnesium while keeping the other materials in a slag. The magnesium will then be collected by rapid quenching. A non-transferred arc plasma torch is ideal for this reaction because of its high enthalpy and improved energy efficiency over conventional methods. Another advantage of plasma is that it allows for the pre-heating or pre-reacting of fine particles before contact with the melt. Thermodynamic calculations using the Gibb energy minimization method were used to determine the most stable compositions of the materials at various temperatures. Energy balances have also been calculated. These results conclude that we can recover approximately 98% of the magnesium with a proper quenching technique. The calculated results are compared with the experimental data, and good agreement between them was observed.

Jan 1, 1999

By John P. Hager

One possible approach for the recovery of mercury from acid plant blow-down sludge in smelters is the use of a vacuum retort reactor for the vaporization of the mercury with subsequent collection of metallic mercury in an attached condenser. An experimental study was undertaken to investigate the vaporization of mercury when present as a compound in the Hg-S-O and Hg-Se systems. A transpiration reactor was modified to operate under reduced pressure and with a continuous flow of inert sweep gas. A water-cooled cold finger was inserted into the exit end of the reactor to provide for the rapid quenching of the exit gases and the collection of the mercury. Rates of vaporization were measured at several temperatures for each compound and were generally found to be constant at a given temperature and reactor pressure. The results were used to determine the minimum operating temperature for 100% vaporization of the compound in 60 minutes. For Hg2SO4, HgSO4, and HgSO/2HgO the required temperatures. for a reactor pressure of 50 Torr. were determined to be 634°, 622°. and 603°C. respectively. For HgO, HgSe, and HgS the required temperatures were 557°. 451°. And 382°C. respectively. For HgS the rate of vaporization was also measured at a reactor pressure of 1 00 Torr. The rate of vaporization was found to be slower resulting in an increased vaporization temperature of 423°C. It was also determined that the mercury vapor present in the exit gas stream can back-react with the other gas species to a significant extent and can result in very little condensed metallic mercury. For the vaporization of both HgS and HgSe. the mercury vapor was found to have back-reacted to the extent that virtually none of the vaporized mercury was collected in metallic form. For the vaporization of Hg2S04? HgS04, and HgSO4*2HgO the amount of metallic mercury recovered varied from approximately 50% for HgS04*2HgO to approximately 10% for Hg2S04 and HgS04. Only for HgO was the recovered mercury in primarily elemental form. The application of the results to the operation of a vacuum retort and condenser system is discussed.

Jan 1, 2001

By Kimberly Conner-Mills

Due to increasingly stringent worldwide environmental regulations for gaseous, aqueous and solid waste emissions, conventional smelting technology cannot effectively process arsenic containing materials. Many globally significant copper properties have copper sulfide mineralogy that has a high arsenic content present as enargite with significant contained precious metals. As global copper, silver and gold demand increases while significant world resources decrease, treatment of sulfide orebodies with enargite is becoming increasingly important. Methods to selectively dissolve and fix arsenic, leaving behind clean copper and precious metals-bearing concentrates could effectively treat these ores.

By J. P. R. deVilliers

A procedure is described whereby gold-containing calcined concentrates and leach residues from refractory gold ores are smelted with carbon to form a small amount of metal. The gold is liberated upon smelting, and is collected in the molten metallic phase, which is easily separable from the slag. The metallic phase consists of approximately 1 to 15 per cent (by mass) of the material after smelting, and the gold content is generally upgraded by a factor of greater than 6 compared with that of the original roasted material. Recoveries better than 95% have routinely been achieved. The quenched metal contains predominant Fe-Ni alloy, as well as minor Fe sulphides and Cu-Fe sulphides. Trace amounts of Fe-Ni arsenide and Au-Cu alloy are also present. The gold content of the metallic phase can be increased further by oxidation of the hot metal in the presence of silica or slag. This will reduce the amount of metal, and will concentrate the gold in a smaller volume. The metallic phase can then be treated hydrometallurgically to recover the nickel and the gold.

Jan 1, 1989

By George A. Calboreanu

In order to overcome drilling and tapping of high hardness wear resistent material in slurry pumps, most of time mild steel inserts are mounted in the mold and after pouring they become an integrated part of the casting. This process is limiting the size and design possibilities of slurry pumps and efforts were made to drill and tap the hard iron itself. The paper will present practical results obtained in drilling and tapping Cr-Mo wear resistent material with hardness in excess of 700 HBN. The life time of the slurry pump parts used in hazardous waste fuel transportation with high slurry velocity and 15% solid loading some of it being quartz, increased 2.5 to 6 times.

Jan 1, 1996

By Charles Zimmerman

The Genesis gold mine, owned and operated by Newmont Gold Co., is located in section 31, T36N, R50E within Eureka County, Nevada along the Carlin Trend of sediment-hosted disseminated gold deposits. Mining commenced in 1986 with present mineable and stockpiled reserves listed at 17,711,000 tons of ore averaging 0.073 opt Au, totalling 1.292 million ounces of gold. Ore is primarily hosted within Devonian calcareous siltstones that have been subjected to intensive argillization and silicification episodes. Additional mineralogic and geochemical features of the Genesis ores include enrichment in iron-oxides, kaolinite, arsenic and antimony; the ore zone is relatively depleted in carbonates and sulfides as a result of supergene and hypogene oxidation. Two major structural zones enhanced the permeability of the siltstones and served as the main hydrothermal conduits within the deposit. Prior to the main ore stage, the host rocks were subjected to metasomatic effects caused by emplacement of the Juro-Cretaceous Goldstrike granodiorite pluton and associated dikes and sills. Micron-size gold occurs in clays, micro-crystalline quartz, and in arsenical complexes. Non-oxidized carbonaceous and sulfidic ores and silica-locked ores result in variable preg-robbing and refractory responses during cyanide recovery. Selective mining and milling has resulted in the successful treatment of the Genesis orebody.

Jan 1, 1988