Search Documents

By Akihide Nagao

The behavior of impurity hydrogen that is contained in starting material or picked up during processing has been little investigated up to now. The hydrogen microprint technique is applied to determine the microscopic location of impurity hydrogen during deformation in aluminum without hydrogen charging. Three kinds of pure aluminum of 99.99% are prepared, in which hydrogen content is varied by changing the atmosphere when they are melted and heat-treated. After rolling, tensile specimens with a gage size of 4 x 4 rnm and 0.5 mm in thickness are stamped out from these three kinds of aluminum sheets. These specimens are covered with a liquid nuclear emulsion of silver bromide crystals, stretched by 5,10 and 15 percent plastic strain or fractured, developed and fixed. SEM micrographs reveal a number of silver particles on the slip lines and on the grain boundaries. Also shown is that the more hydrogen present in the specimen, the more silver grains appear on the slip limes and on the grain boundaries. Consequently, it is concluded that impurity hydrogen is transported to the surface with gliding dislocations during deformation.

Jan 1, 1998

By Mariana Barcelos, Frederico Muylaert Margem, Giulio Rodrigues Altoé, Pedro Amoy Netto, André Gomes, Sergio Neves Monteiro

Environmentally correct composites, made from natural fibers, are among the most investigated and applied today. In this paper, we investigate the mechanical behavior of polyester matrix composites reinforced with continuous fique fibers, through bending tensile tests. Specimens containing 0, 10, 20 and 30% in volume of fique fiber were aligned along the entire length of a mold to create plates of these composites, those plates were cut following the ASTM standard to obtained bending tests specimens. The test was conducted in a Instron Machine and the fractured specimens were analyzed by SEM, the results showed the increase in the materials tensile properties with the increase of fiber amount.

Jan 1, 2015

By Guo Chen, Xuefeng Liao, Tu Hu, Shengzhou Zhang, Hongying Xia, Jinhui Peng, Libo Zhang

Pine nut shell is as raw material for preparation of high surface area activated carbon (HSAAC) by microwave induced KOH activation. The effects of microwave power, activation duration and KOH/C mass rate (R) on the iodine adsorption capability and activated carbon yield were investigated. Additionally the surface characteristics of HSAAC were characterized by nitrogen adsorption isotherms and SEM. The operating variables were optimized utilizing the response surface methodology and were identified microwave power 738W, activation duration 17 min, and R 4, corresponding to a yield of 46.28 % and an iodine number of 2154 mg/g. The key pore structure parameters of HSAAC such as the Brunauer–Emmett–Teller (BET) surface area and total pore volume were estimated to be 3819 m2/g and 2.09 mL/g, respectively. The findings strongly support the feasibility of microwave heating for preparation of HSAAC from spent pine nut shell by microwave induced KOH activation.

Jan 1, 2016

By Zhihe Dou

SHS reaction system has advantages of heat flux density, energy concentration and reaction speed, with sufficient conditions in thermodynamic and kinetic reaction. This paper invented a new technology of SHS metallurgy of preparing melting point alloys and refractory compounds using its own chemical energy. SHS-leaching process for preparing nano boron powder or ultrafine boride powder and SHS-casting process for preparing titanium-based alloy and immiscible alloy were studied. The results indicate that highly active boron powder of greater than purity of 93%, particle size less than 100nm and purity greater than 98.5%, particle size less than 400nm REB6 can be prepared. With SHS-Casting process, the oxygen content of less than 0.59% ferrotitanium, oxygen content of less than 0.5% titanium alloy and ?40-80*100mm large size of CuCr, Cu-Fe alloy ingots were prepared. This technology has greatly enhanced the thermal reduction method added values of preparing metallurgical products and its competitiveness.

Jan 1, 2014

By Neale R. Neelameggham, Ganesan Subramanian

Anthropogenic Heat Flux (AHF) is defined as heat generated from use of non-renewable energy by humans in residential, commercial and industrial activity. State of the art Global Circulation Models (GCM) used to predict global impacts of climate change to help set related policy do not include this heat flux. AHF is considered to be a much smaller an insignificant forcing, solely based on the global mean values. Various Climate models have discussed the “Heat Island Effect ” in high AHF areas. Through the use of simple climate models, it is shown that significant pockets of AHF can impact climate locally in ways significant enough to impact global climate. Inclusion of spatial AHF distribution, rather than a global mean value is important to accurate modeling either on a regional or global scale.

Mar 1, 2017

By D. M. Fermino, C. G. Bastos Andrade, M. G. Fernandes, F. R. Valenzuela-Diaz

Treatments with high concentration solution of inorganic acid at temperatures under boiling point are a usual method for clay minerals structure modification. For many industrial uses bentonites must be cleared of impurities. In the present paper, a sample of Brazilian bentonite from Vitoria da Conquista, Bahia was modified by mild acid attack using hydrochloric acid under moderate conditions (90 °C, reaction times of 1, 6, 12, 18 and 24 h in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, acid solution/clay ratio of 1 g/10 mL). The attacked samples were characterized by CEC, XRF, SEM, EDS and Stereomicroscopy. The purpose of these attacks is to reduce the concentration of impurities with minimal damage in clay minerals structure. The modified bentonite presented good results and tends to be a good economic and environmental alternative to manufacturing products with high added value such as polymer/clay nanocomposites, cosmetics and medicines.

Mar 1, 2017

By Chen Wen, Li Zhao-jia, Zhao Qiang, Ning Shun-ming, Tang Sanchuan, Wang Hong-qiang

"The carbon-burdened and cold-bonded pelletizing-electrosmelting process is used to dispose low-grade manganese, and the qualified rich-manganese slag is obtained. On the condition that reduction roasting temperature was 1000?, reduction time was 45min, particle-size was -1mm, reductant dosage was 1.6%, basicity was 0.3, smelting temperature was 1410?, smelting time was 60min, it had a good effect on the melting between slag and metallographic phase, the manganese content was 32.58%, manganese recovery was 92.16% in the slag; while the iron content was 94.40%, iron recovery was 95.32% in the metallographic phase. It was proved by the demonstration tests.IntroductionManganese is an important raw material for steelmaking, which is extensively utilized in modern industry, the consumption of manganese for iron and steel industry accounts for 90% to 95%. After mining over 30 years, the high-grade manganese resources drop markedly, especially with the hypergrowth of steel industry, the domestic manganese is far from the requirement, as a result, we have to buy significant quantities of manganese overseas. Besides, the property of imported manganese is more and more complex, and the high-grade and lump manganese decrease year by year, while the fines and high-crystal water manganese are on the increase. Therefore, how to make effective use of domestic low-grade manganese and intensify the manganese’s smelting is an effective approach to reduce the cost of manganese series ferroalloy and improves market competitiveness[1-4]. It has important practical meaning."

Jan 1, 2012

By Muhlis Nezihi Saridede, Burak Birol

"The scraps of high quality steels generally contain expensive alloying elements such as chromium, vanadium, nickel, etc. These scraps are melted in an induction or an electric arc furnace and refined in ESR (Electroslag Remelting) purification process. A significant amount of alloying elements are lost during these processes. In order to avoid these losses, scraps can be utilized directly in ESR by skipping the melting step. In this study, 316L stainless steel scraps were refined in ESR with selected synthetic slags. The products were analyzed by optic emission spectrometry and the effects of slag compositions on the alloying element losses were examined. According to the analysis of the scrap and the products, generally chromium, nickel and manganese losses were encountered. It was determined that the alloying element losses has no connection with electrical conductivity. The slag containing CaF2, Al2O3, and FeO gives the optimum Cr and Ni losses.IntroductionElectroslag remelting (ESR), which is the consumable electrode refining process, finds a wide range of utilization for the production of high quality, low inclusion alloys. This process is based on melting a consumable electrode under a molten synthetic slag containing CaF2, Al2O3, CaO etc. The synthetic slag provides the chemical refining and insulation of molten metal from air which leads to a higher purity and an inclusion-free product. [ 1,2] A schematic diagram of ESR system is shown in Figure 1."

Jan 1, 2011

By R. L. Player

"The Copper Isasmelt process has been developed over the past 15 years by Mount Isa Mines Limited (MIM) and the Commonwealth Scientific and Industrial Research Organisation (CSIRO). The first two commercial plants were commissioned in mid 1992.The results of four heat balances on the Mount Isa plant are presented. At a smelting rate of 98 t/hr of chalcopyrite concentrate plus 14 t/hr reverts, the total heat generated was -91MW. Approximately 39% of this energy came from coal, while 50% of the energy reported to the process waste gas. To a first approximation the furnace is near chemical equilibrium.The impurity distribution in the Mount Isa plant was presented. Approximately 91 % As, 85% Cd, 75% Bi, 68% Zn, 60% Sb and Tl, 45% Pb and 30% Te in concentrate was eliminated from the matte.The ""bubble"" frequency of the gas cavity below the foot of the lance was measured at -2. 1Hz. Side bands displaced by -l.lHz modulated the bubble frequency. This was consistent with radial gravity wave motion in the slag bath. The two processes, gas bubbling and wave motion appeared to be coupled together; the bubble frequency was twice the slop wave frequency. IntroductionCopper Isasmelt has been developed over the past 15 years by Mount Isa Mines Limited and the Commonwealth Scientific and Industrial Research Organisation. The process is based on the Sirosmelt lance, invented by researchers at the then Division of Mineral"" and ProcessEngineering ofCSIRO in 1973.The first two commercial scale copper furnaces were commissioned at Mount Isa and the Cyprus Miami Mining Corporation smelter at Miami, Arizona in August and June 1992 respectively.The process concept, the history of the development, and the Mount Isa plant have been described (1, 2, 3).This paper sununarises heat balances obtained on the furnace, the impurity distribution among the output streams and lance injection characteristics."

Jan 1, 1996

By Larry Twidwell, Ed Rosenberg, Courtney Young, Sean Dudley, William Gleason, Maureen Chorney

Experimental and industrially produced polystyrene and silica resins are tested for recovery capabilities of Rare Earth Elements (REE). Testing regimes being used are typical of resin analysis. Inductively Coupled Plasma-AES results indicate that preferential separation and recovery is possible in the adjusted pH range of2 to 10, solution conditions, and resin type. Testing conditions are resulting in structure modification of the composite resin as indicated by X-Ray Diffraction, Differential Scanning Calorimetry, Scanning Electron Microscopy, Mercury Porisometry, and density analysis. Resin modification indicates both surface and internal structure alteration outside of reported standard behavior of resins. Structural changes have ramification for both Rare Earth Recovery RER and traditional resin operations. Analysis shows that the resin uptake of REE can be manipulated for concentration. Further analysis with SEM work indicates that widespread surface and interior modification is taking place as resins load with REE. This modification is leading to pore rupture and particle breakage. Further investigation is being performed to determine the mode of breakage.

Jan 1, 2015

By M. Omneya El-Hussaini, M. Galal Abdel Wahab, A. Mohamed Mahdy, M. Fathi El Shahat

"Lead-zinc mineralization is distributed in Egypt along the Red Sea coast between El Qusier and Ras Banas. A representative sample from Um Gheig was collected and ground to -60 mesh for the mineralogical study. It contains hemimorphite (Zn2SiO4.H2O), sphalerite (ZnS), galena (PbS), calcite (CaCO3) and dolomite (CaMg(CO3)2) beside the gangue minerals gypsum (CaSO4.2H2O) and hematite (Fe2O3). Cadmium seems to be incorporated in the crystal structure of the zinc-lead minerals. The chemical analysis of Um-Gheig representative sample revealed that, it contains 16% zinc combined with 0.1% cadmium, 2.3% lead and 0.1% boron beside other elements.Pug and agitation leaching were performed on samples ground to -200 mesh to achieve the maximum dissolution efficiency of cadmium with respect to other elements. Cadmium leaching efficiency reached 90% by using 40% H2SO4 at S/L ratio 1/2 and stirring time 2 hours at 80o C. Cadmium was then separated as yellow precipitate of CdS from the sulfate leach liquor containing 0.9 g/l Cd, 145 g/l Zn, 0.15 g/l B and 0.01 g/l Pb. Separation of cadmium was carried out by direct precipitation using Na2S as well as H2S. The recovery of 94% cadmium free of zinc was achieved.IntroductionLead-zinc ores occur in Egypt in a few localities distributed along the Red Sea coast between El Qusier and Ras Banas. Um-Gheig Pb-Zn ore is a replacement deposit in limestone and calcareous sandstone in the basal series of the Middle Miocene rocks. The reserve of the ore deposits has been estimated by Soviet and German Experts to be about 900,000 Ton, Bishai [1]. As has been mentioned, zinc is a common element and cadmium is comparatively rare in almost zinc minerals. It was estimated that zinc is 200 times as abundant as cadmium. According to Bodas [2] about 2.1% of cadmium was carried by the Zn mineral hemimorphite (15.3% Zn) in Thailand. Also, Onal et al., [3] found that 164 g/t Cd was carried by Pb–Zn ore sample containing 10.17% Pb and 10.98% Zn from Aladag in Turkey. Cadmium metal has gained great importance due to its wide applications in civil and navy purposes as well as in nuclear field. It is characterized by its ability to absorb thermal neutrons during the chain reaction inside the nuclear reactors. It is also used in the manufacture of sheets which directed the chain reactions [4]."

Jan 1, 2008

By Yuanbo Zhang, Daoyuan Zhang, Youlian Zhou, Guanghui Li, Tao Jiang

"Modified humic acid (MHA) has been developed by Central South University (CSU) and authorized in China. It has been reported that MHA is an effective binder for oxidized pellets prepared from specularite concentrates. In this research, effects of MHA binder on roasting behaviors of the specularite pellets are studied. MHA is an organic binder, containing much carbon, hydrogen, oxygen, etc. During the roasting, MHA can provide some heat because of combustion of hydrocarbon, which is beneficial for the recrystallization of Fe2O3 in the specularite pellets at high temperature. Simultaneously, part of hematite particles within the pellets are firstly reduced to magnetite, then, magnetite is oxidized into secondary hematite, which obviously improves the roasting performance of specularite pellets.IntroductionOxidized pellets have been widely used in steel production as a kind of high quality burden for blast furnace ironmaking [1]. In recent years, production of oxidized pellets is developing very fast. Therefore, the supply of high quality magnetite concentrates, which is the most suitable for pellet production, becomes scarce. It is imperative to pursue new alternative materials for oxidized pellet production [2]. Specularite concentrates have attracted widespread attention due to the advantages of high total Fe grade and low impurity content. However, due to the poor ballability and firing performance, specularite has not yet been widely applied into pellet production [3, 4]."

Jan 1, 2012

By Ritayan Chatterjee, P. K. Mukhopadhyay, Surajit Biswas, Dinabandhu Ghosh, Sandeep Agarwal

An Indian magnetite ore from the Nagaland region was characterized by powder X-ray diffraction, spectroscopies (ultraviolet-visible and Raman), high temperature magnetization and thermal analysis. A Rietveld refinement of the diffraction data revealed that the principal phase present in the sample is magnetite with partial substitution of Fe with Mg (mainly) and Cr, leading to the chemical formula of MgCr0.2Fe1.8O4. The UV-visible spectra of the sample in MeCN solution showed three distinct peaks. The lower region bands are due to metal-oxygen charge transitions and the other band is for d-d transition of iron. Raman spectral study at room temperature gave four characteristics bands of magnetite. The sample underwent a magnetic transition at high temperature and the thermomagnetization curve shows hysteresis during cooling cycle which indicates the possibility of first order structural transition at high temperature. The thermal property of the concentrate was studied by differential scanning calorimetric technique.

Mar 1, 2018

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu

Jan 1, 2015

By N. Kanari

Chalcopyrite concentrates and their pure constituents were chlorinated by C12+N2 between 25 °C and 750 °C. The reaction products were analyzed by SEM, XRD and chemical analysis. The effect of gas flow rate and chlorine content of the gas mixture on the reaction rate were investigated. At room temperature, these solids start to react with chlorine giving metal and sulfur chlorides. Complete reaction is achieved at about 300 °C and the iron and sulfur chlorides were fully volatilized. The chlorination residue is composed of valuable metals' chlorides. A simplified flow - sheet for the treatment of chalcopyrite concentrates by chlorine was suggested.

Jan 1, 1998

By Jianxin Zhang

A process, in which arsenic in the residue is transformed directly into scorodite and copper dissolves into the solution simultaneously, was studied. The process was carried out in acidic ferrous sulfate solution under oxygen pressure. The optimum conditions of the process were determined as follows: the initial H2SO4 concentration of 10 g/L; liquid/solid ratio of 10; Fe/As molar ratio in the feedstock of 1; the addition of calcium lignosulphonate was 1% of sludge; oxygen pressure, temperature and reaction time were 1.5 MPa, 150 °C and 6 h, respectively. Under these conditions, arsenic transformed to crystalline scorodite in size of 5–10 μm, and the transformation efficiency reached 97.60%; meanwhile, the copper was leached with a high efficiency of 93.34%. The stability of the leaching residue was evaluated by TCLP testing, and the results indicated the concentration of arsenic in the leaching solution was extremely low as 0.04 mg/L and met the standard of safe stockpile.

By Drew Sinha

Success of the environmentally benign semiconductor manufacturing depends on the cost-effective integration of the principles of reduce, recover, reuse and recycle from source material to final product disposal. Increasing demand combined with current shortage of polysilicon provided unique opportunities to recover the silicon waste, caused by various defects, in wafer manufacturing process. Current practices relating to recovery and reuse of waste silicon produced, from crystal growth process to finally polished and epitaxially deposited silicon wafer, at Mitsubishi Silicon America is presented. Future plan to recycle the process generated silicon fines produced during the intermediate steps of the wafer manufacturing process such as grinding, slicing, lapping and polishing is also discussed.

Jan 1, 1998

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30t/hour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By Richard J. Abitz

Thennodynamic geochemical models have been applied to assess the relative effectiveness of a variety of reagents added to aqueous waste streams for the removal of radioactive elements. Two aqueous waste streams were examined: effluent derived from the processing of uranium ore and irradiated uranium fuel rods. Simulations of the treatment train were performed to estimate the mass of reagents needed per kilogram of solution, identify pH regions corresponding to solubility minimums, and predict the identity and quantity of precipitated solids. Results generated by the simulations include figures that chart the chemical evolution of the waste stream as reagents are added and summary tables that list mass balances for all reagents and radioactive elements of concern. Model results were used to set initial reagent levels for the treatment trains, minimizing the number of bench-scale tests required to bring the treatment train up to full-scale operation. Additionally, presentation of modeling results at public meetings helps to establish good faith between the federal government, industry, concerned citizens, and media groups.

Jan 1, 1996

By De-qing Geng, Guang-liang Wu

The waste slag generated by the LF refining process of Q345B low alloy hot-rolled steel, still has some refining capabilities. If recycled, it can reduce environmental pollution, and save the economic costs. A research on melting Characteristics of Q345B steel LF refining waste slag was investigated by using orthogonal experimental method, and the effect laws of composition on that were analyzed. Through variance analysis and significance criterion, it is concluded that the optimum ingredient of the regenerated LF refining slag is 25%A12O3, 12%CaF2, 7%MgO and R= (CaO)/ (SiO2) =2.5. And the regression analysis is carried out by using SPSS software, to get the mathematical relationship between ingredient with high reliability and melting temperature of refining slag T=1451.3-6.25CaF2+2.36 R.

Jan 1, 2016