Search Documents

By Aiyuan Ma, Kun Yang, Weiheng Chen, Jinhui Peng, Shiwei Li, Feng Xie, Libo Zhang

In this thesis, a new process of recovering zinc sulfide ores was developed. The novel synthetic coordination leaching process mainly included two steps: microwave assisted phase reconstruction and compound coordination leaching. By applying various techniques, such as chemical composition analysis, X-ray diffractometry (XRD) and Raman spectroscopy, it could be concluded that sulfide phases would directly oxidized to zinc oxides under the 500 ºC microwave roasting and adding 30% Na2O2. What’s more, zinc leaching rate reached to 61.16% within 2 hours. Compared to the current technologies, this procedure had the advantage of avoiding SO2 emission, high leaching efficiency, simple process, manipulate easily, and low cost, which could be expected tremendous application potentials.

Jan 1, 2016

By Sergio N. Monteiro

From the leaves of the sisal plant (Agave sisilana) a relatively strong fiber can be extracted and is nowadays being investigated as a possible reinforcement for polymeric matrix composites. For this purpose, it is important to determine the critical length of the fiber with respect to the matrix to be reinforced. This has never been properly done for sisal fibers in polyester matrix. Therefore, this work characterized the critical length of sisal fibers, with different sizes, embedded in polyester capsules by means of pullout tests. The critical length obtained allowed the sisal fiber/polyester matrix interface shear stress to be calculated. The relevance of these values for polyester composites reinforcement with sisal fibers is discussed.

Jan 1, 2009

By Hong Li, Chenxiao Li, Wenwen Mao, Hua Lu

Directly charging limestone into slag in BOF is a newly emerging technique which broke through the traditional BOF slagging principle. It is necessary to study the decomposition behavior of limestone in converter slag during BOF steelmaking. FeOx, SiO2, MnOx and pre-melting slags were mixed with limestone according to different quality proportion to simulate the environment of limestone in converter slag. TG-DTA results indicated that slag with individual component, including FeOx, SiO2 and MnOx, all had obvious effects on reducing the decomposition temperature of limestone. Pre-melting slags with multiple components had further reducing effects than individual component. XRD results showed converter slag component would react with decomposition product of CaCO3 and generate solid solution or oxide, reducing the activity of CaO and the decomposition temperature of CaCO3.

Mar 1, 2017

By Thierry De Nys

A direct leaching process of sulphidic zinc-based concentrates in aqueous sulphuric acid solutions has been developed by the V.M. R & D Department. By a very accurate control of the oxidation potential of the leach solution, this process enables a separate recovery of the zinc, copper, silver, lead and sulphur of the concentrate and makes it extremely attractive for treating more complex ores. The iron, solubilized during leaching, is eliminated out of the zinc solution by means of the V.M. goethite process. Alternative flow sheets for a conventional zinc electrolysis plant are presented.

Jan 1, 1990

By Jin Yu, Fang-Qiu Zu, Yun Xi, Li-Na Mao

"According to the behaviors of resistivity-temperature of Cu-Sb70 melt, which suggests a partly reversible temperature-induced liquid structure transitions (LST) could occur in this alloy, in this paper, we investigated the dependence of solidification on the liquid state. Both resistivity and temperature were measured to track solidification process. The results show that the nucleating undercooling of the melt which experienced the LST increased and the solidified time decreased. Meanwhile, the solidified microstructures refined evidently, with the microscopic pattern of primary phase changes from disordered pillarlike dendrites into homotaxic ones. Moreover, it is verified that the microstructures would be different if the reversible part of the LST was restrained. The new phenomena and results reflected in this paper suggest that grasping the rules of melt structure change with temperature before material processing will give help for controlling the solidification more effectively and finally resulting in more ideal microstructures.IntroductionThe structure and quality of liquid alloys have a direct and important influence on the structure, performance and quality of the solidified ones. In recent years with in-depth study of liquid structure, researchers have found that some liquid structure transitions (LST) could occur on dependence of the temperature or pressure [1-5]. And the article [6] reported that a pressure-induced reversible LST was found in liquid triphenyl phosphite, which further confirmed the authenticity of the existence of the LST. Furthermore, in our earlier studies of Sn-based melts using resistivity method, some abnormal structure changes induced by temperature have been found at hundreds of degrees above liqiudus, and these LSTs are partly reversible[7]. This phenomenon has been discussed and it is suggested that the reversible LST in Sn-based melts are related to the short-range ordering (SRO) structures of Sn, which are tetrahedron structure with covalent bonding. However, does this reversible LST exist in other melts too?"

Jan 1, 2012

By Yuzura Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about I 880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties 'such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

By Mario Sanchez, Jose Palacios, Fernando Parada

Carbon steels have less than 0.02% copper and have low atmospheric corrosion resistance. The addition of at least 0.20 wt% Cu improves this property. Also, 0.8 wt% Cu in steel shows a hardening potential for developing high strength corrosion resistant steels. Copper slags containing 42–45% of iron, silica and minor amounts of copper were used for producing Fe–Cu alloys by reducing the oxides contained in the slag to obtain a Fe-0.84 wt% Cu alloy, which could be suitable as feeding material to manufacture a corrosion resistance steel, and also would be an alternative for minimizing the copper industry ’s environmental impact, and to introduce the application of the Circular Economy concept to the natural resources exploitation, especially in countries where their economy is strongly based in mining and metallurgical extraction.

Mar 1, 2018

By M. Girgis

The behavior of arsenic III during electrolytic refining of copper in acidic copper ?sulphate electrolytes was studied by different electrochemical methods such as, linear potential sweep, cyclic voltammetry, chronoamperometry and chronopotentiometry. The study showed that arsenic behaves as a depolarizing ion and has a deleterious effect on copper deposit. Three substrates; Pb, Cu and Ag were used during the refining process and the electrode kinetics were found similar for both Cu and Pb electrodes while a little difference was found for the Ag electrode. A microscopic study by scanning electron microscope was undertaken to show the influence of arsenic on deposit's morphology. Surface analyses of the deposit were carried out by some electronspectroscopic techniques such as Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS). The results showed that arsenic coexists with copper deposit at potential?~ -0.25 V.

Jan 1, 1987

By Xuemei Zheng, Aiyuan Ma, Yonggang Zuo, Jinhui Peng, Shiwei Li, Libo Zhang

The effect of moisture content on the dielectric properties and microwave drying behavior of zirconium hydroxide was studied by using an open-ended sensor dielectric measurement system at the frequency of 2.45 GHz. The experimental results showed that moisture content can significantly influence the variation of dielectric properties. Dielectric constant, loss factor and loss tangent all increase with the increasing moisture content. Compared with the conventional drying method, the microwave-assisted drying method resulted in a substantial decrease (81.8%) in the drying time, and the drying effect was better at the lower power level of 600 W. This study offers the useful information on dielectric properties of zirconium hydroxide, which can be used for developing microwave drying applications in mineral processing and designing better microwave sensors for measuring zirconium hydroxide moisture content.

Jan 1, 2015

By Chuan-fu Zhang

The fibrous precursor can be obtained by coordination precipitation process, using oxalate, cobalt chloride and ammonia. XRD pattern of precursor precipitated at pH=9.0 is different from that of ß-CoC2O4?2H2O precipitated at pH=1.0 which indicates that the precursor powders are one type of cobalt complex. According to the results of element analysis and IR spectra, it can be inferred that the composition of the precursor is [Co(NH3)x]C2O4?H2O(x=1.2?..6) formed by the coordination reaction at pH=9.00 in the Co(II)-C2O42--NH3-NH4+-H2O system. It?s found that the fibrous cobalt powders greatly inherited the morphologies of the precursors. Many factors could affect the formation of the fibrous cobalt precursor powders, such as the initial Co2+concentration, pH value and so on. The SEM images show how they influence the morphologies of the precursor powders. By adding proper surfactant, the dispersion of the precursor powders would be improved. At last, the final product-fibrous cobalt powders which are about 0.3~0.5min size and 40~60 in aspect ratio were produced by thermal decomposition of fibrous cobalt complex at 400~500°C in the weak reducing atmosphere.

Jan 1, 2006

By Yuanbo Zhang, Zhixiong You, Guanghui Li, Peidan Wen, Tao Jiang

Sn-bearing iron ore containing small amount of Zn, Pb and As is one of the typical complex polymetallic ores in China. This kind of ore is not extensively utilized due to the complicated relationships between iron and other associated nonferrous metal minerals. Excessive contents of these elements would adversely affect the metallurgical operation as well as the quality of steel products. In this study, reduction behavior of Sn was detailedly investigated using H2 or mixed H2/CO as reductant. The results revealed Sn volatilization was improved in the presence of H2 than individual CO/CO2 atmosphere. Simultaneous volatilization of these elements was realized by roasting under weak H2/CO reducing potential, and metallization reduction was advantageous for further Zn volitilization. A metallic pellet (DRI) with Fe metallization greater than 90%, residual Sn, Zn, Pb and As content of 0.054%, 0.012%, 0.0045% and 0.09% was prepared via a simulated reducing gas of coal gasification.

Jan 1, 2015

By A. H. Castillejos E., F. A. Acosta G.

Filtration is widely used as a terminal refining step for metals, particularly for the casting of aluminum alloys, but still more knowledge is required to understand how several factors affect the efficiency of removal of inclusions. In this study, both, initial and long term filtration efficiencies of a ceramic foam filter have been obtained from the computed trajectories of solid particles suspended in molten aluminum. The complex structure of the foam filters is represented by a unit cell which is formed by a pair of pores with average dimensions. The fluid flow field was determined from the numerical solution of the Navier-Stokes equation, and periodic fully developed flow was assumed at the inlet of the calculation domain, as a boundary condition. This flow field corresponds to laminar flow as that found in ceramic filters operating under normal conditions. Computed initial filtration efficiencies showed that filtration efficiency decreases sharply with fluid velocity for particles larger than 30 µm, but smaller particles are better trapped at higher fluid velocities. Finally, it was found that long term filtration efficiency for particles of 8 µm decreased with time, in spite that perfect particle-wall attachment was assumed. Filter aging was considered in this study, and it was found that the distorted flow field, around the already trapped small inclusions prevented further collection.

Jan 1, 1999

By Gordon Lewis

A complex mixture of hydrated reaction products is obtained from hydrothermally treated refractory cements and castable concretes. TGA can be used both to identify the product phases in the mixture and to determine a quantitative relationship among the phases. When reacted mixtures contain compounds that decompose simultaneously, or nearly so, additional assumptions must be introduced in order to develop a quantitative phase analysis. It is the purpose of this paper to examine some of these assumptions and to demonstrate their application, particularly to refractory cement systems.

Jan 1, 1982

By Ruirui Wei, Mingrui Yang, Xuewei Lv

Calcium ferrite, as the main bonding phase in the sintering process, greatly influences the property of sintered ore. Ultrasonic vibration has been widely applied to the treatment of metals to improve the properties of metals. In this work, ultrasonic vibration was introduced into the calcium ferrite and numerical simulation was carried out by solving the Rayleigh-Plesset equation to investigate the influence of ultrasonic conditions, including frequency, power and initial radii of cavitation bubbles on the cavitation bubbling behavior in calcium ferrite melt. The results indicated that lower ultrasonic frequency, higher power, and an appropriate initial radius of bubble promotes ultrasonic cavitation.

Mar 1, 2018

By A. K. Kyllo, N. B. Gray, B. N. McCurry

"Dynamic control of the formation of a solidified layer between a pipe wall and a flowing melt enables the flow rate to be adjusted in real time. This solidified layer can be generated by using a coolant on the outside of the pipe wall to remove the required heat. The coolant, and hence the solidified layer, can be controlled remotely. The dynamic behaviour of the solidified layer was investigated by both physical experiments and mathematical modelling. The mathematical model has been developed using a finite difference technique to describe conduction through the pipe wall and solidified layer. Results from the model were consistent with previous steadystate experimental results using molten lead. Experiments are currently being carried out using molten tin in a recirculating circuit with a cooling system that is instrumented for accurate computer control to validate the model. The circuit is designed for flowrates of up to 24 kg/s (86 tph) of molten tin. Steady-state and dynamic predictions were made for the current rig.Industrial SignificanceThe current method of choice for tapping slags, metals and mattes from many metallurgical furnaces is using an oxygen lance to open the taphole and using a clay plug to close it. There are, however, some significant drawbacks in this method. The heat generated by the oxygen lance erodes the refractory lining of the taphole, as well as the clay plug, and the furnace products themselves corrode the taphole. Using an oxygen lance is also a significant safety hazard to the operators as they must work in close proximity to the furnace and be subjected to a shower of sparks while opening the taphole. Also, the flowrate of material through the taphole cannot be controlled online as the diameter of the opening cannot be varied easily. This feature means that the level of product in a furnace cannot be kept constant."

Jan 1, 1999

By Shangshu Li, Xin Li, Xionggang Lu, Xingli Zou, Kai Zheng, Yinshuai Wang

Ti5Si3/TiC composite has been successfully prepared from the titanium-rich slag/SiO2/C mixtures precursors by an electrochemical process. The electrochemical production process was carried out in molten CaCl2 salt at 1000 °C and 3.8 V. A pressed cylindrical pellet of titanium-rich slag/SiO2/C mixtures served as a cathode, and a solid oxide oxygen-ion-conducting membrane (SOM) tube filled with carbon-saturated liquid tin acted as an anode. The phase transformation of the cathode pellets during electrolysis process was investigated, the microstructure of the obtained products was characterized. It is found that the reaction pathways can be divided into three main stages during the electro-reduction process. The first stage is the generation of calcium compound, the second stage is the electrochemical reduction of the compound, and the third stage is the formation of Ti5Si3/TiC composite. The prepared Ti5Si3/TiC composite exhibits homogenous and nodular particle morphology.

Mar 1, 2018

By Suzzann Nordwick

The metallurgical treatment of mercury-containing materials for precious or base metals recovery imposes many processing and environmental challenges. Mercury is usually present as elemental or cinnabar. Historically, mercury has been removed from mined ores pyrometallurgically by roasting, but hydrometallurgical methods have also been employed. For example, alkaline sodium sulfide solution acts as an universal solvent for most mercury compounds. While, most other metals are highly insoluble in this solution. This allows for a high degree of selective separation of mercury from other metals with the exception of tin, antimony and arsenic. Mercury leached with a solution of sodium hydroxide and sodium sulfide or sulfur can be re-covered by cementation or stabilized through sulfide precipitation. Hydrometallurgical technology for the pretreatment of mercury removal from gold, silver, and base metal ores using alkaline sulfide leaching will be discussed with a focus on alkaline sulfide leaching of mercury sulfide-containing materials.

Jan 1, 2003

By B. Erik Ydstie, Dimitrios I. Gerogiorgis, Sridhar S. Seetharaman

"Carbothermic production of aluminium is an important alternative to electrolytic processes and has in fact been identified several decades ago as a potentially feasible and profitable process. The cornerstone principle is to take advantage of the endothermic reduction reaction between carbon and alumina instead of resorting to extreme amounts of electric energy to ionize and reduce aluminium oxide to aluminium. Electric energy is necessary only for heating purposes.The present study focuses on constructing and solving a steady-state electrothermic model for obtaining the spatial distributions for electric potential, electric field intensity and temperature. The complex issues of reaction kinetics and multiphase flow are handled by an approximation and are not addressed at the present stage, due to the lack of complete validated models. Because of its inherent complexity, the reaction slag is considered a pseudohomogeneous layer.An electrothermic simulation encompasses important research challenges, due to the limited knowledge of thermophysical properties for high-temperature multi component molten slags. Therefore, thermophysical property modeling and a systematic compilation of published data is a necessary and major first step towards enhancing understanding of the process fundamentals. Models are obtained by analyzing measurement data from numerous literature references for the density, viscosity, thermal and electrical conductivity and specific heat capacity of the slag.The electric potential, field intensity and temperature distributions obtained reveal interesting maxima which indicate localized superheating and lead to important engineering conclusions. The temperature profile calculated will serve as the foundation for the flow problem solution. This computational study will form a basis for future research towards combining the scopes of microscale CFD modeling and mesoscale process modeling into a unified modeling approach."

Jan 1, 2001

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Jie Qiu, Yun Chen, Kai Tang

Isothermal reduction kinetics of CF2 by 30% CO and 70% N2 at 1123, 1173 and 1223 K was investigated by TGA in this study. The reduction rate analysis indicated that reduction of CF2 comprises three stages during the whole reduction process, Apparent activation energy of samples CF2 reduction is 34.37 kJ/mol. The ln-ln analysis implied the reduction of CF2 was expressed initially by a 2D subsequently by 3D shrinking layer reaction.

Mar 1, 2017

By Shun Myung Shin, Dong Hyo Yang

Cobalt is recovered from square type of spent lithium ion batteries (LIBs) containing 5~20 % Co, 5~7 % Li, 5~10 % Ni, 15% organic chemicals, and 7% plastics together with Cu, Al, Fe, and Mn. The waste LIB was prepared by physical treatment. After screening, the crushed LIBs were separated to +8 mesh, -8/+16 mesh, and -16 mesh powder. Among these, -16 mesh powder was selected for leaching. The leaching test was investigated at 2 M H2SO4, 6 vol.% H2O2, reaction temperature 60 ?, agitation speed 300 rpm, solid/liquid ratio 50 g/ 500 ml, reaction time 1 h. The leaching efficiency of cobalt was more than 99 % and its concentration was 24.9 g/L. For removing of impurities such as copper, iron, and aluminum in the leaching solution before cobalt solvent extraction, the impurities were eliminated by pH control with alkali solution. For selective extraction of cobalt, the aqueous phase removed impurities was equilibrated with different volumes of 0.4 M Cyanex 272 saponified of 50 %. Extraction efficiency of cobalt was about 80 % at first step. Separation coefficient (ßCo/Li) of cobalt and lithium extractions was 206.5. Over 9.0 % of pure cobalt sulfate solution was obtained after stripping with H2SO4 solution.

Jan 1, 2008