Search Documents

By Jr. Loper, M. H. Kim, H. H. Jo, C. S. Kang, T. S. Song

"An investigation has been conducted to describe the effect of grain refiner (e.g.,Ti) or modifier (e.g., Sr) on the microstructure of an Al-11.3wt%Si alloy produced by the Ohno horizontal continuous casting process using a heated mold so as to obtain directional solidification at high cooling rate of 300 to 2000°C/s. Experimental results demonstrated that the directionality of the primary a grain was promoted by the addition of0.2 to 0.4%Ti or by the addition of0.02%Sr, whereas the addition of0.6%Ti suppressed this directionality. Feathery a grains were promoted by the addition of 0.2%Ti, while these feathery a grains were suppressed when over 0.4%Ti (grain refinement) or when 0.02%Sr was added. The addition of Ti also resulted in increased coarsening of the eutectic Si in these Al-1 l.3wt%Si alloys.IntroductionThe mechanical properties of conventionally cast Al-Si alloys can be enhanced through judicious control of the casting parameters, by the addition of grain refiners (e.g., Ti) and by the addition of eutectic modifiers (e.g., Sr).[1-3] The Ohno continuous casting process[4-5] uses a heated mold (maintained at a temperature above the alloy liquidus temperature) to produce a casting with a mirror surface free of shrinkage defects. The process is especially suitable for the production of high quality and non-deformable rods of small diameter. This study was conducted at investigate the effects of Ti and Sr on the microstructure of Al-1 l .3wt%Si rods cast by the 01).no process."

Jan 1, 1998

By E. T. White, Dean Ilievski

"Mathematical modelling of the precipitation process requires that the kinetics of crystal growth, nucleation and agglomeration be known. This paper reviews the current state of knowledge on these precipitation sub-processes (ie. growth, nucleation and agglomeration) and describes a number of experimental techniques for estimating their kinetics. The experimental methods used to generate the precipitation data and the data analysis techniques used to extract the kinetics information from the data are discussed separately. There is no universal ""best"" technique for determining the kinetics. However, studies on multi-crystal systems are more reliable for modelling purposes than are single crystal studies. The selection of a technique will depend on which sub-processes are present. A problem with all kinetics studies is that there is generally a large uncertainty in the estimated kinetic parameters. This stems from the scatter in the experimental data being further propagated by the mathematical techniques used to extract the kinetic parameters.IntroductionCrystallisation operations, including precipitation, are widely used in a number of hydrometallurgical processes to recover a desired component or to remove an undesired impurity. The goals of industrial precipitation processes are to maximise the recovery while maintaining product quality (generally product crystal size distribution, purity and morphology and product handling properties). Knowledge of the precipitation mechanisms and kinetics is invaluable for designing new precipitators or for improving existing units. The mechanistic and kinetic information is generally incorporated into mathematical precipitator models, which are then used for process design and optimisation."

Jan 1, 1996

By Motohiro Horiguchi, Kazuo Ichii, Toshio Oishi

"As a fundamental study to prepare copper-based alloys with rare earths (RE: La, Gd, Nd, Ce and Y) without any inclusions, the solubility of rare earth in liquid copper was experimentally determined. Liquid copper alloys were equilibrated with carbon and rare earth carbide in a graphite crucible in an argon atmosphere at 1523-1873 K.Solubilities of rare earth in liquid copper were determined by approaching the equilibrium values from both the lower and the ·higher concentrations than those expected· in the preliminary experiments. They were expressed as a function of temperature. Carbon in Cu-RE alloy was also analyzed and thermodynamically discussed.IntroductionOver the past several years, the demand for highly conductive and high strength copper-based alloys, such as Cu-Cr, Cu-Zr and Cu-Cr-Zr for use in electronic materials has increased.1 -7 These alloying elements are very reactive and easily oxidized to form oxide inclusions during melting. To avoid the oxide inclusions, it may be effective to utilize the strong reducing power of carbon in conditions under which no carbides form.In this study, to provide fundamental data for producing Cu-RE( rare earth) alloys without any inclusions, the solubility of rare earth in liquid copper in equilibrium with .carbon .was determined and discussed on the basis of the experimental results and the thermodynamic data.ExperimentalSample preparation for equilibrium experimentsOxygen-free copper (99.99%), lanthanum (99.9%), gadolinium (99.9%), neodymium (99.9%), cerium (99.9%) and yttrium (99.9%), and their oxides were used as starting materials.Each rare earth carbide was prepared by mixing rare earth oxide with carbon, which is a little more than the stoichiometric composition, pressing it into a tablet form and sintering at about 2000.K for 20 ks in a vacuum furnace using a graphite crucible. Powder X-ray analysis showed that only the carbon and rare earth carbide (REC2) was present in each sample.Cu-RE mother alloys (5-20 mass % RE) were prepared beforehand by mixing metallic rare earth with oxygen-free copper, and melting in an electric arc furnace."

Jan 1, 2000

By F. M. Wang, J. P. Lin, G. Y. Tang, H. C. Zhou, Y. F. Liang, F. Ye

"Fe-6.5%Si alloy is a very excellent soft magnetic material compared with conventional Si steel (Si content ~ 3.5%), especially in high frequencies with reduced iron losses and noises. But it is hard to be fabricated due to its brittleness at room temperature. Dynamic electropulsing is applied to the cold rolled Fe-6.5%Si sheet during tensile deformation. Mechanical and microstructural properties are investigated with different electropulsing and strain rate. It is found that the yield stress decreases and the elongation increases dramatically with the application of dynamic electropulsing. It is indicated that the work hardening could be reduced with the dynamic electropulsing during deformation, which provides a promising way to fabricate this alloy sheet much easier.Introduction Fe-6.5%Si (weight percent, same as below) alloy has more excellent soft magnetic properties compared with conventional silicon steel (Si content ~ 3.5%), such as higher resistivity, higher permeability, near zero magnetostriction, etc. and exhibits much lower core losses and noises [1]. However, Fe-6.5%Si is very brittle at room temperature and hard to be fabricated in strip by conventional hot-cold rolling process [2]. This lack of low-temperature ductility has been generally attributed to structural ordering ofB2 and D03 phases [3]. Several methods have been developed to avoid its brittleness, such as chemical vapor deposition (CVD) [4], rapid quenching [5, 6], dipping and diffusion [7, 8], direct powder rolling (DPR) [9], etc. However, hot-cold rolling method is still of interest for industrial applications. In our previous work, this alloy can be cold rolled after certain thermomechanical process and heat treatment [10-13]. The cold rolled sheet exhibits some extent of ductility [11]. However, side cracks are common for the rolled sheet, it is very necessary to improve the ductility of this alloy by other technical applications."

Jan 1, 2012

By Chuanfu Zhang, Jinliang Wang

"Brickless reaction shaft is the latest progress for flash smelting furnace. However, there are many factors influence the melting point of the freeze slag inside brickless reaction shaft, and their variational regularities are not obvious, thus, it is difficult for conventional methods to analyze accurately the complex data. In this research, the experiment data of slag melting point were processed based on optimal discrimination plane. For this method, two orthogonal vectors were firstly built up based on the Fisher's criterion, and then the experiment data were projected onto the two vectors, thus, two-dimensional feature vectors were extracted as criteria to determine the factors effect degree on the slag melting point. Results show that the CaO content is the greatest factor to the melting point of the freeze slag inside brickless reaction shaft, the content of Fe3O4, SiO2, Cu2 O and MgO is the second, and the FeO content is the last.IntroductionBrickless reaction shaft is the latest progress of flash smelting furnace reaction shaft. To research the influence factors on the slag melting point inside the brickless reaction shaft is significant to form freeze slag with compact structure, good heat insulation, certain intensity, appropriate thickness and reasonable distribution, to extend furnace life, to reduce energy consumption, and to promote safe production.However, due to the complex components, there are many factors influence the melting points of the freeze slag inside brickless reaction shaft, and their variational regularities are not obvious. Therefore, it is difficult for conventional methods, such as variance analysis, data fitting, etc., to analyze accurately the complex experiment data.Pattern recognition can easily classify information, even if there are many influencing factors. For pattern recognition, there are some sub-disciplines such as discriminant analysis, feature extraction, error estimation, cluster analysis (together sometimes called statistical pattern recognition), grammatical inference, parsing and matching (sometimes called syntactical and structural pattern recognition) [1, 2]."

Jan 1, 2012

By David B. Dreisinger

Mass and heat balance modeling is a powerful tool for the design and analysis of hydrometallurgical process flowsheets. In this first of two papers, we examine the basic fundamentals of mass and heat balance modeling, and apply these concepts to several flowsheets using a simple spreadsheet model. In this way, we aim to demonstrate how such models are not only easy to construct, but can also be indispensable for comparing various flowsheet alternatives, for making rational economic decisions, and for developing a basic understanding of existing process behaviour.

Jan 1, 2002

Segregation roasting tests were carried out on Zaire cobalt oxide ores assaying about 2% Co and 3.5 to 6.5% Cu. The major parameters tested during the laboratory investigations were temperature, dosage and type of reducing agent, dosage and type of chloridizing agent, and particle size. Results showed that standard conditions suited to the segregation of copper ores, i.e. low temperature and low dosages of reducing and chloridizing agents, resulted in the segregation of copper only, while conditions suited to the segregation of lateritic nickel, i.e. higher temperature and increased dosages of reducing and chloridizing agents, led to a successful segregation of both copper and cobalt. Under the best conditions, 88% of the cobalt and 98% of the copper could be recovered in a concentrate assaying 32.5% Cu and 8.5% Co. Alternatives to process such a concentrate are briefly reviewed.

Jan 1, 1993

By P. Koskinen

Outokumpu Oy has 30 years' experience in nickel production. It is mainly based on the technology developed within the company. The production chain starts from the mines reaching to the high-grade cathode nickel and the stainless steel manufacturing. As a multi-metal producer Outokumpu has the advantage to exploit from nickel raw materials also other valuable metals and intermediate products which can be processed at the company's various plants. The main source of nickel concentrate is nowadays the Enonkoski Mine started up in early 1986. It is the most modern mine in Finland being provided with the latest Finnish high-tech systems. Nickel concentrates are smelted at the Harjavalta Works using Outokumpu's internationally well-known flash smelting method. Also nickel containing residues and secondaries' are used as raw materials. The high-grade nickel matte from the smelter is then refined at the nickel refinery in a hydrometallurgical process, which was also developed by the company's own research staff. These processes have been continually improved and capacities gradually enlarged to 18 000 mtpy of cathode nickel. Besides plating, melting and superalloying purposes part of the nickel ends in stainless steel at the Tornio Works. The production was started in 1976 and has reached an established position on the European market.

Jan 1, 1988

By I. Gaballah

Decontamination of synthetic solutions of copper acetate, chloride, nitrate and sulfate containing 10, 100 and 1000 ppm of copper, using chemically treated barks has been studied. Metal percent removal from solutions depends on the pH and the initial concentration and to some extent on the salt used. It varies from 40 to 99 % of the solution initial metallic ion's content. The maximum retention capacity of the treated bark varies from 31 to 43 mg of Cu per gram of dry modified bark. Bark loaded with copper had been analysed by Scanning Electron Microscopy and lnfra Red spectroscopy. Cu is uniformally distributed in the bulk of the bark. No copper segregation is observed. It seems that copper is bound to the acidic sites of the bark. Anions are not detected on the copper loaded bark neither with the SEM or with the IR spectroscopy.

Jan 1, 1993

By Anja Pfennig, Thomas Böllinghaus, Marcus Wolf

During CCS components are exposed to a corrosive environment and mechanical stress which results in corrosion fatigue and is inevitably followed by the lifetime reduction of these components. The lifetime reduction of the cyclically loaded high alloyed stainless injectionpipe steel AISI 420C (X46Cr13, 1.4034) constantly exposed to highly corrosive CO2- saturated hot thermal water is demonstrated in in-situ-laboratory experiments (T = 60 °C, brine: Stuttgart Aquifer, flow rate: 30 l/h, CO2) in an environment similar to the on-shore CCS-site in the Northern German Bassin. In-situ tension-compression experiments were established simultaneously along with electrochemical measurements using a newly designed corrosion chamber in a resonant testing machine at a frequency as low as 30 – 40 Hz. In addition technical CO2 was introduced into the closed system at a rate close to 9 L/h. S-N plots, micrographic analysis and surface analysis of the fracture surface are demonstrated. X46Cr13 (surface roughness Rz = 4) reached the maximum number of cycles (12.5 x 106) at stress amplitude of 173 MPa producing a low scatter range of 1:3.5. Hydroxide and siderite layers were found on pits and crack surfaces. No typical fatigue limit exists. Pit corrosion prior to crack initiation may be identified as failure cause.

Jan 1, 2016

By T. Feldmann

Despite the ubiquity of applications for germanium, there is a lack of practically useful solubility data in acidic solutions. Previous studies were done at ambient temperature and only for commonly used acids (H2SO4, HCl). Hence, an investigation of the solubility of GeO2 in different acids was undertaken. Several inorganic and organic acids were studied in the concentration range of 1–11 mol/L and at 23, 40, and 60 °C. In the case of H2SO4 and HCl previous data was confirmed. Lower acidity resulted in a higher solubility for Ge at all tested temperatures. Tests done at 40 and 60 °C and low to moderate acidity levels, gave slightly increased solubility values at higher temperatures compared to 23 °C. This wasn’t the case at higher acidity levels, i.e., the solubility curves at different temperatures converge at high acidity. Lastly, a relationship of water activity and GeO2 solubility in different acid media was established.

By Ann M. Hagni

Reflected Light Microscopy (RLM) And Scanning Electron Microscopic-Energy Dispersive Spectroscopic Analysis (SEM-EDS) Study Of Electric Arc Furnace (EAF) Dusts Have Shown That Their Mineralogy Is Complex And Varied. The Particles Are Largely Spherical, And Can Be Seen In RLM Sections To Be Composed Of Franklinite, And Zincite, But They Show Significant Solid Solution With Each Other And May Contain Small Amounts Of Chromium. These Crystalline Phases Occur As Crystals And Skeletal Growths Within Ca-Fe-Si Glass. Because Chlorine Is A Deleterious Constituent In Recovered Zinc Products From EAF Dusts, Special Attention Has Been Given To Chlorine-Bearing Phases, And They Include Hydrophylite (Cacl2), Lime (Cao), And Organic Phases. Pyrohydrolysis-Treated EAF Dusts With Silica (Si02), Tungstite (W03), Alumina (A1203), And Bunsenite (Nio) Additives Contain Franklinite, Scheelite (Cawo4), Willemite (Zn2SiO4), And Hematite (Fe2O3)

Jan 1, 1992

By C. Alexandru Sonoc

Donnan Dialysis uses ion exchange membranes to extract and separate cations. The driving force is provided by differences in chemical potential, rather than by electric fields or pressure. A Donnan Dialysis based process to recover lithium, nickel, cobalt, manganese, and organic acid lixiviant from recycled lithium ion battery cathodes is under development. In this paper we present a model of Donnan Dialysis and results of simulations of the aforementioned process. The simulations show that 170 m2 of membranes can process 1000 L of leachate ([Li+] = 0.285 M, [Co2+] = [Ni2+] = [Mn2+] = 0.095 M, pH 2) in two days and recover 94.1% of the lithium (as lithium carbonate), 99.4% of the transition metals (as mixed sulphates ready for solvent extraction), and all of the organic acid using 423 mol of H2SO4 and 268 mol of KHCO3.

By John E. Dutrizac, Tzong T. Chen

"Laboratory experiments were undertaken to ascertain the behaviour of various ""impurity"" species during the precipitation of hematite directly from ferric sulphate solutions at 225°C and in the presence of 40 or 50 g/L of hematite seed. Copper, nickel and zinc are not significantly incorporated in hematite precipitates. Although the nickel contents increase to 0.22% as the Ni concentration increases to 60 g/L, the solid solution Ni contents are low relative to the bulk Ni contents. Thus, part of the Ni may be present as tiny particles of poorly soluble NiS04.H20. Increasing germanium concentrations to 2,000 mg/L result in products containing up to 0.59% Ge. The Ge occurs either in solid solution in the hematite or is adsorbed on the nanometer-size hematite crystallites. Increasing As(V) concentrations to 10 g/L increase the AsO4 contents of the products up to 16%. However, the products consist of hematite together with As04-containing Fe(SO4)(OH) and an unknown Fe-AsO4 species. All the hematite products contain - 1% SO4 which appears to be adsorbed on the nanometer-size hematite crystallites.IntroductionDissolved iron is a common impurity in most hydrometallurgical processing circuits and, generally, the iron must be eliminated prior to the subsequent recovery of the sought after metals. Simple neutralization of iron-rich solutions yields slurries which are difficult to thicken and filter. To address these concerns, the jarosite, goethite and hematite processes have been developed, and these technologies are able to reject the dissolved iron in a readily filterable form [1]. Despite its higher cost, the hematite process offers several potential advantages. Because hematite is an iron-rich, high-density compound, its formation would reduce the mass of residue and the size of a residue storage pond. Hematite is the thermodynamically stable form of iron under ambient conditions, and this stability would facilitate the impoundment of hematite precipitates. Furthermore, hematite has some market potential for cement manufacture and even for iron making [2]. In all the commercial hematite processes, the dissolved ferric ions are first reduced to the ferrous state. Subsequently, the pH of the solution is adjusted and the solution is then oxidized. The ferric ions gradually generated during solution oxidation hydrolyze and precipitate mostly as hematite, although commercial hematite products also contain trace or minor amounts of jarosite-type compounds. However, there are potential advantages in precipitating hematite directly from ferric ion solutions, as the reduction and subsequent oxidation of the iron are not required. Although the precipitation of hematite directly from relatively concentrated ferric sulphate solutions (up to 0.5 M Fe(SO4)is) was recently demonstrated [3], the behaviour of impurity species during hematite precipitation is largely unknown. To address this issue, systematic laboratory experiments were undertaken to ascertain the behaviour of a number of ""impurity"" species during the precipitation of hematite directly from ferric sulphate solutions at 225°C, and the results are presented in this paper."

Jan 1, 2012

By Nobuhiro Shinihara, Makio Naito, Keizo Uematsu, Tadashi Horta, Hiroya Abe, Masataro Okumiya

"A significant variation of strength was noted in silicon nitride ceramics made through the powder compaction processing with minor processing changes. The relevance of the fracture strength to the microstructure was examined in these ceramics. In the examination of microstructure, the ceramics were made into thinned specimens, and their internal structures were observed with an optical microscope in the transmission mode. This technique can distinguish a difference in microstructure associated with the minor processing changes. The strength of all ceramics examined in this experiment was qualitatively correlated with the -pore size distribution in the specimens. Clearly, the elimination of these detrimental defects will enhance the reliability of ceramics.IntroductionIn ceramics made through powder processing, a variation of properties is often encountered [l ,2]. This brings a major problem on producing reliable and cost-effective ceramics. The variation is often ascribed to the changes in the characteristics of defects. However, there is no clear evidence f\)r this explanation due to the lack of an adequate tool for identifying the defects determining the properties. Details of the origin of the variation have still been poorly understood.A new technique is very promising for clarifying the origin of the variation [3,4]. This has very high potential in detecting minor differences in structure for .engineering ceramics. With this technique, ceramics are made transparent with its thinning down to about 50 µ m and their internal structures are observed with various types of optical microscopes in the transmission mode. The characteristics of the defects determined through this approach were found to be directly related to the strength of the ceramics [4-6].The objective of this study is to clarify the ongm of fracture strength of silicon nitride ceramics. This material is representative of high performance ceramics, and the origin is of great practical interest. For this study, silicon nitride ceramics with minor changes in processing condition were prepared. Specific feature focused in this study is the difference of large pore structure determined with the new technique and its relevance to the strength of the silicon nitride ceramics."

Jan 1, 2000

By Emil B. Milosavljevic

The photochemical reactions of cyanide ion induced by light were investigated in the presence or absence of a titanium(IV) oxide semiconductor photocatalyst. The light sources employed were the sun and arrays of either mercury or fluorescent (cool white) lamps. The results obtained verify that cyanide decomposes much faster when TiO2 is present in the solution and that it is first oxidized to cyanate. However, contrary to the previous studies, it is established that cyanide is subsequently further oxidized via nitrite all the way to nitrate irrespective of the light source. As expected, the rates of the oxidation processes decrease with the illumination source utilized in the following order: Hg-lamps > sunlight > fluorescent lamps. As nitrate is a significantly less hazardous contaminant than cyanide, complete photocatalytic oxidation of cyanide to nitrate may be a viable method for decontamination of cyanide wastes. Contrary to previous claims, we find that cyanide is slowly photochemically decomposed even in the absence of TiO2. For example, with the mercury lamps as the light source, in two hours, cyanide concentration decreases to essentially zero; up to 7% was converted to cyanate and the remainder to unidentified products.

Jan 1, 1992

By J. E. Sallee

An experimental study has been conducted on the level of arsenic contamination in samples of zinc oxide when the zinc oxide is contacted with gas mixtures containing As4O6(g). This contamination has been determined as a function of A4O6 saturation pressure, temperature, zinc oxide sample surface area, impurities, and oxygen level in the gas mixture. The results indicated a rather clean separation can be achieved between condensed zinc oxide and gaseous arsenic oxide as long as attention is given to temperature control, and the final zinc oxide surface area. For a 300°C operation temperature and an AqOg saturation pressure of 0.38 TORR (or 0.05% As406 by volume), the contamination level is expected to be approximately 100 ppm. This suggests that arsenical dusts can be treated in the HRD flame reactor process and a reasonable purity zinc oxideproduct produced. The results also show no evidence of zinc arsenite or zinc arsenate formation.

Jan 1, 1994

By Xia Hong-ying, Peng Jin-hui, Zheng Zhao-qiang, Zhang Li-bo

"Preparation of activated carbon from the walnut shell by microwave assisted steam activation was studied. Influences of the three parameters, activation temperature, activation duration and steam flow rate on the adsorption capacity and yield of walnut shell activated carbon(WSAC) were investigated,optimization process was obtained by the Response Surface Methodology (RSM). The optimum preparation conditions were as follows: activation temperature of 980°C, activation duration of 41 min and steam flow rate of 1.66 ml/min. The optimum conditions resulted in an activation carbon with an iodine number of 1025 mg/g and a yield of 52.17%, while the BET surface area, total pore volume and average pore diameter of WSAC were 1328m2/g, 0.72ml/g and 2.2nm respectively. The study supported the potentiality of comprehensive utilization ofWalnut shell and the benefits of the microwave heating.IntroductionActivated carbons are one of the most important adsorbent materials in modern society because of its abundantly developed pore structure, strong adsorption ability, high surface area and thermo stability. They have extensive application in many industries fields which include gas purification [1], catalyst supports [2] and other pollutants [3]. However, in recent years, the industrial production of activated carbon is facing the problem of raw material scarcity and high cost, which limit to be widely used. Therefore, the selection of an appropriate precursor plays an important role and it has become hot sport to seek cheap raw material to lower preparation cost. As a kind of reproducible resource, the waste from agriculture and forestry is a high-grade raw material for preparing activated carbon due to is high carbon content, such as palm shell [4], rice hull [5], and coconut shell [6]. At present Walnut shell is widely accepted to be a renewable source of biomass. According to statistics, there is more than 1000,000 tonnes of walnut shells are produced in China annually [7]. As a good precursor for activated carbon production, Walnut shell is a major agricultural waste, to make better use of the cheap and abundant agricultural waste, it is proposed for activated carbon production."

Jan 1, 2014

By Min Zhu, Yu Ji, An-chao Ren

"After being welded in the weld plant, the 100-meter heavy rails with the specification of 60kg/m are found broken during the straightening process in four planes. Failure analysis is made using the optical microscope and SEM with the result showing that the broken rail contains the imperfection of protrusion which exists at the edge of rail foot, about 1 00mm away from the rail end. When the protrusion is peeled off by deseamer from rail surface, cold scratch is generated which causes the rail to be broken during the subsequent straightening process. By adjusting the roll diameter differences between top and bottom roll of universal finishing mill and the height of pass line, it is possible to maintain the rails flat when leaving the mill. This prevents the upsweep and downsweep phenomena and, thus, the imperfection of protrusion can be eliminated. IntroductionThe development of rail transit worldwide has entered into a new era since the 1960s. The hi-tech rail transit system has gradually gained recognition over the world. In particular, the emergence of new-type passenger trains represented by TGV of France, ICE of Germany and Shinkansen of Japan and heavy haul trains as well, has revealed the charming way and more prosperous future of the modern and hi-tech rail transit system to the people all over the world. It should be pointed out that rail transit system is still the most effective solution to traffic jams among urban cities and in the central cities during the 21 '1 century, especially high-speed railway and subway which take overwhelming advantages over air transport, marine transport and road transport in terms of high speed, high efficiency, safety, comfort, environment protection and high flow. With the trend of increasing speed and heavier load of trains, higher product quality of rails is demanded. The rails for passenger dedicated lines require high cleanness, high accuracy in size, high flatness, high surface quality and large size (100-meter fixed length). The rail quality has direct influence on the operating performance of rail and railway traffic safety. The 100-meter heavy rails with the specification of 60kg/m are broken subject to the straightening process in four planes after being welded in the weld plant. This paper analyzes the reason for rails being broken and provides the theoretical proof for determining the rolling process."

Jan 1, 2013

By J. D. Miller

Gold adsorption from cyanide solutions by activated carbon has been studied at great length during the past decade. Findings from past research are reviewed and discussed with respect to structural features of various carbons, including carbon black, activated carbon, graphite and diamond.

Jan 1, 1991