Search Documents

During electrowinning of nickel chloride, hydrochloric acid was regenerated instead of chlorine in a two membrane cell, by segregating the chloride catholyte with an anion exchange membrane, and the sulphate anolyte with a cation exchange membrane from the middle electrolyte (ampholyte) compartment. Successful operation of such a cell depends on controlling chloride leakage through the cation exchange membrane to the anolyte. Small amounts of chlorine gas could be detected in the oxygen evolved at the anode. In this paper, the chloride. leakage as a function of various types of cation exchange membrane and different composition of the anolyte is reported and discussed. Ag+ was added to the anolyte to eliminate chloride leakage to the anode. The cell voltage, electrode potential and voltage drop over the membrane as a function of current density has also been investigated.

Jan 1, 1996

By K. Murayama, M. Kawakami, T. Takenaka, S. Yokoyama

"Cokes play an important role of spacer in blast furnace. However, they degenerate during Boudouard reaction. Blast furnace cokes are reacted with pure C02 at I 072 to 1673 K. Reaction rate was obtained by the weight change of spherical specimen. The specimen after reaction was examined by microscopic observation. The reaction rate increased with temperature and was expressed by two Arrhenius type lines. The activation energy was 126 KJ/mol at higher temperature than 13 73 K and 202 KJ/mol at lower temperature range. At the higher temperature range, the reaction proceeded from the surface leaving unreacted core, whereas homogeneously whole inside at lower temperature. The porosity increased from the center to surface at higher temperature, whereas it was almost constant at lower temperature.IntroductionThe cokes have the function of fuel, reductant and spacer to keep gas and liquid flow in the blast furnace. Thus, the reaction mechanism of coke with several gas and the strength after the reaction should be important factor to control the blast furnace operation. The reaction mechanism of coke with C02 has been studied extensively. The rate equations were derived by Gadsby[ I], Ergun[2] and Turkdogan and Vinters[3]. They were compared and discussed by Kobayashi and Omori [ 4]. Effect of crystallization degree on the reaction rate was examined by Kashiwaya and Ishii[5]. Catalytic enhancement effect of ash componets have been clarified by Kashiwaya et. al. [6]. Although degradation of coke in blast furnace has been examined recently[7], however, the degradation of coke after the reaction with C02 has not been well clarified yet. In the present work, the metallurgical coke specimen was heated in N2 and C02 and the reaction mechanism and degradation behavior after the reaction was investigated."

Jan 1, 2000

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

By P. Henry

A novel electrochemical cell has been developed for the recovery of MnO2 from residue of pyrolusite ore leading loaded with Fe, Al Ni, Co and Si impurities, This new process can be considered as an alternative to the traditional methods : S02, H2O2 or bioleaching. It has been observed to proceed fairly rapidly and could prove to be a more economically viable process, as well as being more environmentally acceptable. Electrochemical characterization and kinetic studies have shown that MnO2 is effectively leached by electrogenerated ferrous ions at high current density from a pulp containing less than 5 g8 Fe. The chemical reactions are : Cathode (inox) : 2F23+ + 2e ? 2 Fe2+ Bulk: MnO2 + 2 fe2+ 4H+ ? Mn2+ + 2 Fe3+ + 2 H2O Anode (Pb-Ag) : H2O ? ½ O2 + 2H+ + 2e Global: MnO2 +2H+ Fe2+ = Mn2+ + H2O + 1/2 O2 The catholyte (MnO2 pulp) circulates upward in the expanded mesh cathode separated from the sulfuric acid solution anolyte by a separator which shows high mechanical resistance, low porosity, low potential drop, and reasonable cost. Laboratory and mini-pilot tests have led to the construction of an OT crating pilot plant (100 kg/hr) able to leach more than 95% of Mn, Ni, Co at 1000-1200 A/m2, 50°C with high faradic yield (> 95 %) and low power consumption (3.2 kWh/kg kWh/kg &4D). New applications like the treatment of spent Zn-Mn batteries, polluted soils, spent catalysts and oxide ore (cobalt, nickel) with electrogenerated redox species are now investigated at a laboratory and mini-pilot scale.

Jan 1, 2000

By Demaerel. J. P.

Arsenic plays a major role during electroreflning of copper. Both the arsenic content in the anode and the arsenic concentration of the electrolyte have, in conjunction with other impurities such as lead, antimony, bismuth and oxygen, a direct influence on the quality of the cathode. The mechanisms are currently slime. inclusion and precipitation of insoluble compounds in the bulk of the electrolyte. Arsenic has also been reported to have a depassivating effect on the anode. An influence on the anode slime adhesion has also been found. A literature survey is given and these data are compared with and completed by our own results based on lab and pilot scale experiments as well as on Olen tank.house practice.

Jan 1, 1987

By V. Blet

Rare earth elements (REE) are regarded today as highly critical raw materials but currently lack suitable recycling processes. A combined hydro- and pyrometallurgical process aimed at REE recovery from used NdFeB permanent magnets was recently developed by the CEA. The process integrates the physico-chemical treatment of magnets, followed by a solvent extraction step for the recovery and intra-REE separation using a selective extractant. A subsequent pyrometallurgical treatment via molten chloride salt electrolysis allowed the isolation of pure Dy metal. Technical-economic assessment and life-cycle analysis were also conducted. Following this first successful demonstration, a new project aimed at the recovery of REE from end-of-life nickel-metal-hydride batteries is currently being developed in association with industrial and academic partners. The project aims at evaluating from an experimental and economic perspective different processes converging at the production of value-added products such as cermet materials for catalytic applications, purified REO concentrates, or metallic alloys.

By H. Cui

Rapid technological development has caused an increase in the demand for rare earths. Ancylite, a strontium rare earth carbonate, is a potentially significant source of rare earths. In this research paper, essential aspects of the magnetic separation and flotation processes for Bear Lodge ore are presented. A flowsheet is proposed based on an optimization of the variables and flotation simulation. The economic feasibility of the proposed processing operation is analyzed.

By Songsong Wang

Recently, replacing Pierce-Smith converting process with the oxygen bottom-blowing continuous converting technology has become a new research focus. Based on the principle of Gibbs free energy minimization, the thermodynamic model of oxygen bottom-blowing continuous converting multiphase equilibrium system has been established. The elements distribution behavior is calculated at the same burden composition and operation parameters as the industrial production. The results show that the absolute errors of the mass fraction (wt%) of Cu, Fe, S, Pb, Zn, As, Sb, Bi in crude copper are 0.06, 0.0030, 0.070, 0.38, 0.39, 0.020, 0.017, 0.034, 0.010, respectively, and the absolute errors of the mass fraction (wt%) of Cu, Fe, S, Pb, Zn, As, Sb, Bi in slag are 0.53, 0.81, 0.020, 0.23, 2.5, 0.0048, 0.0010, 0.0030, 1.49, respectively. The calculated results agree well with the actual industrial production data, indicating that the model can be well applied in the oxygen bottom-blowing continuous converting practice.

By Pertti Koukkari

The novel Jarogain process combines treatment of the jarosite residue of zinc manufacturing and processing of arc furnace dust from steelmaking to a holistic recovery technology. The new hydrometallurgical approach is targeted to recover the major constituents (Fe, Zn, Pb) as well as valuable components such as Ag, Au, In and Ga from the jarosite-dust mixture as reusable concentrates. The fractionation process proposed by VTT and Aalto University takes advantage of jarosite being readily fine powder and directly available for wet chemical processing. Jarogain process provides an energy efficient opportunity for jarosite utilization as value added products. The experimental proof-of-concept of key stages of the process will be outlined with a comparison of available pyrometallurgical treatments of jarosite waste. The techno-economical assessment is based on estimated investment and variable production cost using the discounted cash flow (DCF) analysis.

By Joseph Goodwill

1. PURPOSE The objective of this paper is to summarize a study undertaken by the EPRI Center for Metals Production (CMP). The overall purpose of the study was to identify electrolytic opportunities that might merit consideration for joint development by industry and EPRI. 2. SCOPE The electrolytic technologies of interest to this study include: Electrorefining, Electrowinning, and Fused-salt electrolysis. Recovery from primary, secondary, and waste materials were included in this effort; however, we excluded from consideration: Plating and coating operations, such as electrogalvanizing; Mining and milling operations in which electric energy is predominantly used for comminution; Electrothermal processes in which submerged-arc, open electric-arc, and plasma-based smelting processes use electric energy largely to provide a melting or refining ("heating") capability; and Aluminum electrotechnologies since these were the subject of a separate study (CMP 86-2). We recognize that there may be some "gray areas" between these excluded areas and the electrolytic sectors of interest. For this reason, a secondary criterium was used, namely, if the major use of electric energy was to extract or refine the

Jan 1, 1990

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By Ray Y. Lin

This study explores the formation of sodium pyrosulfate in molten sodium sulfate resulting from dissolution of SO3 at temperatures between 1160 and 1250 K. Solubility of SO3 in Na2SO4 melts at temperatures between 1160 and 1250 K under gas mixtures of SO2, O2 and argon was investigated applying a thermogravemetric analysis (TGA) technique. The activity of Na2O in the melt was determined with a high temperature electrochemical cell (ECC). Results showed that the SO3 solubility in molten Na2SO4 increases with decreasing temperatures and increasing SO3 partial pressures. Enthalpy of SO3 dissolution in molten Na2SO4 was calculated to be -119 kJ/mol for infinite dilute solutions. Thermochemistry of Na2SO4-Na2S2O7 melts was analyzed based on information obtained from both TGA and ECC techniques. Detailed examinations of the earlier low temperature measurements in the Na2SO4-Na2S2O7 system along with data from this study reveal that the solution behavior between Na2SO4 and Na2S2O7 can be satisfactorily treated as regular with the interaction parameter, , being 2.7 kJ/mol. The phase diagram and the field of SO3 partial pressure has been generated with the thermodynamic calculation using a regular solution approach.

Jan 1, 2006

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In tungsten ion-exchange process, excessive sodium impurity enters into ammonium tungstate solution. However, the Na content of the final ammonium paratungstate (APT) product must be strictly controlled. Consequently, it is necessary to remove Na from the ammonium tungstate solution during processing in order to obtain the required purity of APT. In this study, porous Na specific absorbent, Na1+xAlxTi2−x(PO4)3, is used to remove Na from the ammonium tungstate solution. Through experiments, the effect of reagent concentration of Na1+xAlxTi2−x(PO4)3, reaction time, reaction temperature and Na concentration on the Na removal were investigated. The results showed that under optimal reaction conditions of reagent amount of NATP 1.0 times of theoretical amount, reaction temperature 25 °C and reaction time 15 min, the Na removal from commercial (NH4)2WO4 solution can reach 98%. Na1+xAlxTi2−x(PO4)3 has a good applicability to different Na+ concentrations. The obtained APT product reaches the national standard purity of zero level.

Jan 1, 2014

By T. Kimura, H. Ohba

"Much effort has been made to reduce the energy requirement in zinc electrowinning. In order to keep energy consumption low, either to make cell voltage low or current .efficiency high is necessary. Decrease of cell voltage practically depends on how to reduce ohmic resistance in the electrolyte and the anode crust. To realize these, new concept was proposed and the pilot plant has been operated. The space between a cathode and an anode is halved by utilizing the frame insulator. With these frames the anodes and cathodes compose of a unit of electrodes, and this unit is handled by newly designed electrode handling machine (E.H.M.). The process includes lifting up electrodes, expanding the space between a cathode and an anode, cleaning them, stripping the deposited zinc and returning the unit to the cell. As a result, cell voltage is kept as low as calculated and predictable energy reduction has been achieved. IntroductionIn the recent trend of a rapid appreciation of the Japanese yen, Akita Zinc Refinery of Mitsubishi Metal Corporation has been confronted by problems of relatively high operating costs. In order to compete with other overseas zinc refineries, it is necessary to reduce the cost of zinc production, especially the cost of electric power which now accounts for .up to 35 % of the entire cost of production. Three fourth of the electric power used at Akita Zinc Refinery is for the electrolysis. Therefore it is extremely important to reduce the cost of electrolysis.There are two possible measures for solving the problem; one is to use more nighttime electricity taking the advantage of its inexpensive power price, and the other is to reduce electric power consumption.As a part of a rationalization plan carried out in 1986, Akita Zinc Refinery increased the number of operating cells. As a result, when nighttime electricity is used, the silicone rectifier has been able to operate at full capacity. Moreover, by new schemes of ""increase of area for electrodeposition by ralslng the liquid level of electrolyte"" and ""increase of the number of electrodes in each cell"", current density could be lowered and as a result, the electric power consumption has been improved. In order to raise nighttime ratio even higher, installation of an additional rectifier and cells would be required."

Jan 1, 1988

By J. W. Holzenthaler

Teams continue to play a major role at the Phelps Dodge Mining Company El Paso Operations, especially during the present time of low copper prices. The El Paso Operations' teams have taken the initiative during this copper market downturn and have helped reduce operating costs significantly. Because of this, Phelps Dodge El Paso Operations has continued to grow within the team process by creating a total, non- exempt salaried workforce. In the last year alone, the El Paso Operations have implemented three major initiatives to accommodate the team process. The first was the creation of "guiding principles", a policies and procedures handbook. Second was the "zero and beyond" safety initiative. Third was team compensation. In addition, the Copper Products Company has now adopted a work-team environment, following the lead of the refinery.

Jan 1, 1999

By Tomás Vargas

The catalytic role of Thiobacillus ferrooxidans in the dissolution of chalcopyrite was studied by leaching pure massive samples of this sulfide with a pure strain of Thiobacillus ferrooxidans (ATCC 19859). Monitoring of the bacterial activity showed that an important fraction of the total bacteria generated during leaching remained attached to the chalcopyrite surface. Bacteria grown in the system, which were the offspring of bacteria adhered to chalcopyrite, was well explained as the result of the utilization of ferrous ion and sulfur as energy sources. The potential for indirect and direct action was fully utilized by the existing bacteria and the leaching process was controlled by the kinetics of chalcopyrite dissolution.

Jan 1, 1990

By Shenghui Guo, Jianbo Lan, Hongying Xia, Jinhui Peng, Lihua Zhang, Libo Zhang

Spent Hawaii nut shell was converted into a high-quality activated carbon via steam physical activation. Analysis of the experiment including activation temperature, activation duration, steam flow rate on the adsorption capability and yield of activated carbon were identified. Response surface methodology showed that the activation temperature was identified as 866 , an activation duration of 36 min and a steam flow rate of 2.5mL/min with the methylene blue adsorption number of 195 mg/g and yield of 77.75%. The key parameters that characterize quality of the activated carbon such as the BET surface area, total pore volume and average pore diameter were estimated to be 1125m2 /g, 0.94mL/g and 5.21 nm, respectively. Additionally, by the SEM analyses of char and activated carbon, the surface of activated carbon has large number of pores of irregular and heterogeneous morphology.

Jan 1, 2016

By William R. Opie

Considerable effort by extractive metallurgical research organizations has been devoted recently to developing pollution-free processes for treating copper sulfide concentrates. A number of hydrometallurgical processes are in various stages of development and have been subjected to economic evaluation. Although the hydrometallurgical approaches eliminate SO2 emission problems, they create objectionable effluents and residues, make precious metals recovery complex, and are not very efficient for treating chalcopyrite. Furthermore, they are consumers of considerably more energy than pyrometallurgical processes which produce blister copper that can be electrorefined to commercial grade cathodes. This paper discusses a pyrometallurgical process under development by AMAX Base Metals Research & Development, Inc. (1) The original objectives set for the process development were: 1. Sulfur control of at least 95% with elimination of fugitive emissions. 2. Copper and precious metal recoveries as good as or better than conventional processes. 3. Low capital cost. 4. Competitive operating costs 5. Use of known proven technology where applicable.

Jan 1, 1976

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By Cledwyn Mangunda

Mining operations generate Acid Mine Drainage (AMD) that poses a significant threat to the natural environment. AMD treatment using Ca(OH)2 leads to the precipitation of a sludge dominated by a mixture of ferri-oxyhydroxides. This sludge has poor dewatering tendencies and is deposited in landfills with potential for metal remobilization. This study investigated the dewatering behaviour of a precipitate formed during elevated temperature treatment of a primary, pre-settled sludge from the neutralisation of aqueous acidic Fe2(SO4)3 and Ca(OH)2 solutions in an MSMPR reactor. The resulting treated precipitates were analysed for micro-properties, with results showing that an increase in the secondary reactor temperature from 25 °C up to 50 °C led to an increase in mean particle size, a decrease in the number of particles and improved dewatering behaviour at a ferric concentration of 300 mg/L. This was ascribed to the attainment of a circum-neutral surface charge that favoured agglomeration and a change in micro and nano-structure that allowed for better water passage.