Search Documents

By R. G. Reddy

The effect of solid particles on viscosity behavior of Na2O-O-B2O3-SiO2 melts of composition XSio2/XNa2o =0.5 and in the temperature range of 900- 1150 K was studied. Samples were analyzed by X-ray diffraction and optical microscopy. The results showed that a crystalline phase (NaBO2) was formed and its amount increases with decrease in X,, from 0.50 to 0.25. The experimental viscosity values were compared with the predicted values using our viscosity model developed earlier. At low temperatures, for low content of B2O3 , the experimental values exhibits a large deviation from the predicted values. It was concluded that the deviation was due to the formation of solid particles in the molten slags. The existence of these solid particles increased the viscosity values significantly. A new viscosity model was developed to include the effect of solid particles.

Jan 1, 1993

By Pertti Koukkari, Nagendra Tripathi, Karri Penttilä, Justin Salminen

A computational fluid dynamic model for a novel flash ironmaking process based on the direct gaseous reduction of iron oxide concentrates is presented. The model solves the threedimensional governing equations including both gas-phase and gas-solid reaction kinetics. The turbulence-chemistry interaction in the gas-phase is modeled by the eddy dissipation concept incorporating chemical kinetics. The particle cloud model is used to track the particle phase in a Lagrangian framework. A nucleation and growth kinetics rate expression is adopted to calculate the reduction rate of magnetite concentrate particles. Benchmark experiments reported in the literature for a nonreacting swirling gas jet and a nonpremixed hydrogen jet flame were simulated for validation. The model predictions showed good agreement with measurements in terms of gas velocity, gas temperature and species concentrations. The relevance of the computational model for the analysis of a bench reactor operation and the design of an industrialpilot plant is discussed.

Jan 1, 2014

By Marcelo A. Martorano, Moyses L. Lima, João B. F. Neto

"Directional solidification is an essential refining step to obtain solar grade silicon from metallurgical silicon. This step can be carried out in a Bridgman furnace, where nearly constant temperature gradients and solidification velocities are imposed on the solid-liquid interface. In the present work, this directional solidification was conducted in a static furnace, in which large temperature gradients and low solidification velocities were enforced to increase macrosegregation. The resulting ingots were analyzed regarding their macrostructures, microstructures and chemical composition. Using measured cooling curves in the ingot as boundary conditions, a mathematical model based on the concept of a stagnant liquid layer at the solid-liquid interface was implemented to predict the macrosegregation profiles. The chemical analyses of the ingots show macrosegregation of several impurities to the ingots top. The mathematical model indicates that liquid convection plays an important role in stabilizing the planar solid-liquid interface, increasing the macrosegregation of impurities.IntroductionMost of silicon used for photovoltaic (PV) energy production is obtained by chemical processes, such as, Siemens and its derivations [1]. However, these chemical processes have drawbacks related to relatively high energy consumption and investment costs, and to safety and environmental problems. In order to overcome these difficulties and to fulfill the silicon demand for PV applications, several metallurgical routes are under development [2] to produce silicon of enough purity to PV applications (SoG-Si) from metallurgical grade silicon (MG-Si).Metallurgical routes involve different steps among which the directional solidification is pointed out as a fundamental one [1]. Directional solidification can cause macrosegregation of impurities to the last part of the ingot to solidify. The impurity segregation during solidification is related to the low solute partition coefficient (k0) between liquid and solid silicon. Most of the impurities in MG-Si have k0 << 1, except for boron, phosphorus and oxygen, which require specific steps of the metallurgical routes to be eliminated. The equilibrium partition coefficient and the solubility limits for the most important impurities in MG-Si are shown in table 1"

Jan 1, 2014

By Thomas Brynjulfsen, Merete Tangstad, Eli Ringdalen

Manganese ore fines cannot be added to the submerged arc furnace directly as they will prevent even gas flow through the burden. Low gas permeability in the burden will lower the degree of pre-reduction of ore subsequently increase the carbon and energy consumption of the process. In order to utilize manganese ore fines in the furnace, they are typically agglomerated into sinter. In this work, the melting and reduction properties of Gabonese sinter and Gabonese ore have been investigated in pilot scale experiments. Two experiments were conducted, one with 100% sinter as manganese source and one with 50/50 sinter and ore. Lime was used to achieve a charge basicity of 0.72 in both experiments. The composition of slag samples from the excavation of the furnace was established using EPMA(WDS), and the composition of the tapped slag and metal was found using XRF. It was found that while the coke-bed size would determine the tapped slag composition, the melting behavior of the Mn source would determine the mixing with lime.

Jan 1, 2014

By Patrik Yrjas, Daniel Lindberg, Emil Vainio

Recovery of trace elements from different industrial waste streams is important in realizing the goals of the circular economy. Ash streams from waste combustion can contain high levels of both toxic and valuable trace elements. These elements can be separated during the combustion process based on volatilization and condensation, as well as being separated in post-combustion processes, through thermal or leaching treatment. In this study, an overview is given of the thermal methods for recovery of valuable elements from ash fractions derived from waste incineration. In addition, a case study is presented of the behaviour of ash-forming elements in combustion of MSW and demolition wood, with special focus on the elements Co, Cu, and Sb. In conclusion, it is shown that thermodynamic modeling of high temperature processes can be a useful tool to predict ash behavior both during combustion and in the post combustion treatment of the ash.

Mar 1, 2018

By Tatsuro Ariyama, Michitaka Sato, Atsushi Sakai, Sumiyuki Kishimoto, Ryota Murai

"In order to achieve high pulverized coal injection operation in a blast furnace, optimization of the injection lance arrangement was carried out using an experimental furnace and mathematical models. To increase the injection rate of pulverized coal, it is required to raise the combustion efficiency of pulverized coal. It became clear that multi-point injection and the lance arrangement to avoid interference among the coal streams injected were so effective in increasing combustion efficiency. With these findings, the eccentric double lance arrangement has been newly developed.At NKK, Fukuyama No.4 Blast Furnace, after the improvement of the lance arrangement, the maximum injection rate reached up to 230 kg/thm and an average monthly record of 218 kg/thm was successfully achieved.IntroductionFrom the viewpoints of reducing the production cost of pig iron and prolonging coke oven life, high pulverized coal injection over 200 kglthm is actively pursued by ironmaking industries[1-2].Coal particles injected into the blast furnace are consumed by combustion in the raceway and also in-furnace reaction like solution-loss reaction (C + CO2 = 2CO). The amount of coal consumed by the latter process is determined by the carbon balance in the blast furnace and there is a limit. Therefore, to increase the injection rate, it is desirable to improve the combustion efficiency in the raceway. For these purposes, the optimization of the lance arrangement was examined by a hot model and mathematical models."

Jan 1, 1996

By Yoshiyuki Matsui

As one of the factors of frequent troubles on iron-making blast in recent years, increased size of the blast furnace and high-productivity operation are pointed out. Consequently, great importance is attached to deadman shape and solid flow at the lower part of furnace. In the present study, firstly, the blast furnace raceway formation under the intensive coal injection by measurement of micro wave reflection gunned through a tuyere is discussed. As the flow rate of coke as the momentum of coke into raceway decreases by combustion of coal injected into tuyeres, the depth of raceway defined as the maximum position of micro wave reflection is easy to contract. It is expected that this new technology could detect the raceway collapse phenomena in short time and that the stability of raceway in coal injection is different from that in all coke operation. Secondly, the reduced stockline surface profile was measured by the reflection intensity of microwave struck from the furnace top after blow-off with stockline reduced, and investigation was made on the countermeasures for changes in the raceway depth and furnace body profile during operation. As a result, it has been clarified that flow-down of coke into the lower part of blast furnace and inflow into the raceway are greatly subject to the existence of deadman which is the packed structure of the lower part of furnace, and further, they are closely related to dynamic behavior of the raceway, and affect changes of the furnace body profile.

Jan 1, 2006

By D. E. Larson

The U. S. Bureau of Mines has developed a image analysis methodology to correlate the energy consumed during the grinding of an ore to the mineral liberation achieved. Energy consumption values are obtained using a laboratory-scale ball mill equipped with a torque sensor, and an automated image analyzer is used to determine the liberation present in ground products. By combining liberation information with energy consumption data an appraisal can be made of the energy required to liberate the mineral(s) of interest. Results of tests performed on a complex sulfide material determined the effects of grind duration on the liberation achieved and the energy efficiency.

Jan 1, 1995

By J. T. Stanley

The identification of crystal phases and crystal chemistry can be critical to understanding the mechanisms of waste material interaction with native soils. Understanding these mechanisms can suggest correct methods for remediation and treatment. A program is outlined and examples are given of the development of effective techniques for rapid phase identification of environmental samples using electron microscopy. The program concentrates on the development of integrated object oriented software to aid rapid searching of online databases and rapid simulation of potential crystal diffraction patterns. Examples come from dried sludge taken from a former hard-chrome plating facility.

Jan 1, 1993

By Shuichiro Okada

Various efforts to reduce energy consumption and smelting cost are made at Tamano Smelter. Production of anode copper has been increased by about 30 % and energy requirement has been decreased about 50 % respectively. Challenges toward more higher goal are being continued. Details about the following are described in this paper. 1 Waste heat recovery Steam recovery at up-take of FSFE Heat recovery from waste gas of anode furnaces 2 Application of tonnage oxygen 3 Application of pulverized carbonaceous fuels to the flash smelting furnace with furnace electrodes ( FSFE ) 4 Application of computer control system to copper smelting 5 Improvement of the fugitive gas collecting system 6 Improvement of the mechanical tuyere puncher for the converter furnace

Jan 1, 1983

By C. J. Lewis

This presentation concerns calcium oxide-better known as high calcium quick lime High calcium quicklime is produced by calcining high calcium limestone, mostly in the many rotary kilns located throughout the United States and Canada. This paper presents suggestions on the handling of lime based on field experience. The subjects covered are chemical analyses, transporta¬tion, lime storage, lime slaking to form a water slurry of calcium hydroxide solids, slurry transportation, slurry viscosity, and scaling of lime slurries. It is hoped that the comments on the foregoing areas will be of use to those designing or operating lime systems.

Jan 1, 1992

By Thomas F. Hagelien, Stein Tore Johansen, Svend Graadahl

"The dross appearing at the surface of an aluminium melt consists, in addition to aluminium, of mainly oxide films but also other non metallic inclusions. The inclusion particles are often poorly wetted by the metal and accumulate at the metal surface. However, in impeller stirred reactors for melt refining stirring may be exceedingly strong and inclusions accumulated at the metal surface may be entrained into the bulk metal. Concerning inclusion removal, such effects may deteriorate the effectiveness of melt refining.In this paper we investigate the surface entrainment of buoyant particles in a water model of an impeller stirred refining reactor. Under varying operating conditions the particle concentration in the bulk liquid is measured by laser light attenuation. The observed entrainment of particles is explained theoretically and metallurgical consequences of the findings are discussed.IntroductionIn the modern cast house continuos metal refining and casting is well established. One of the most distinct advances in metal refining has been the introduction of degassers which introduce bubbles into the metal. The bubbles act to remove dissolved elements together with nonmetallic inclusions. In the most efficient degassers stirring by different kind of rotors is applied to increase mass transfer and inclusion removal. However, it has been known from experience in the cast house that for violent stirring the concentration of some types of inclusions may increase from inlet to outlet of the reactor. This phenomenon has so far been attributed to production of dross in the reactor due to oxidation of metal. Due to removal of inclusions by bubbles the dross layer inside the reactor must be expected to increase in thickness by time. The removed inclusions and produced oxides due to strong stirring is removed at regular interval by the operators of the degasser. However, a fundamental understanding of the phenomena which take place in and below the dross layer is lacking. In the present work we add buoyant particles to the surface of a refining reactor and investigate how these particles may be entrained and dispersed into the liquid depending on the flow conditions. Similar investigations for gas stirred ladles have been performed by Taniguchi et al [1] who found that below a critical gas flow rate all particles are trapped at the surface. Above the critical gas flowrate the surface velocity are sufficiently high to entrain the particles. In this situation it looks like all particles are ready for the melt and a balance between terminal velocity and turbulent dispersion determine the concentration in the liquid."

Jan 1, 1999

By V. Gornitz

The Orphan mine uranium deposit, Grand Canyon, Arizona, is a cylindrical collapse-breccia pipe, 70 to 150 m in diameter and 500 m deep. Pipe fill was derived from the Supai Group, Hermit Shale, and the Coconino Sandstone. Uraninite, with Cu, Fe, Pb, Zn and Ni-Co sulfides is concentrated along the pipe boundary ring fracture (annular ring) and within the central porous sandstone matrix. There is some suggestion of vertical and lateral zonation of U with respect to Cu. Reduction of ferric oxide cement from red beds and recrystallization of carbonate, with formation of kaolinite preceded major ore deposition. Early Ni sulfides, arsenides and disseminated pyrite were followed by massive pyrite, and botryoidal uraninite, which in turn was suc-ceeded by Cu, Zn and Pb sulfides. A second, later generation of uraninite was closely intergrown with hematite and base metal sulfides. Oxidation of primary minerals may have been associated with Tertiary regional uplift. The paragenetic sequence closely resembles that of other Grand Canyon breccia pipes, except for the extensive development of the distinctive uraninite-hematite association. Mineral assemblages at the Orphan suggest possible mixing of the metal-bearing solution(s) with a more oxidized fluid, containing soluble uranyl complexes. Homogenization temperatures of fluid inclusions in calcite (GO-lIO?C) at the Orphan fall within the lower end of the range observed at other breccia pipes.

Jan 1, 1987

By Miller, Geoffrey W.

The Ravensthorpe Nickel Project (RNP) flow sheet provides for the upgrading of Ni & Co in a size based beneficiation process prior to leaching. The upgrading effect on Ni and Co makes the beneticiation process a powerful addition to the flow sheet. Multiple linear regression (MLR) analysis based on 351 individual batch tests, 52 large scale composites and 21 pilot plant tests has been used to successfully model beneticiation product grade, recovery, upgrade and mass recovery. Statistically, 83% and 96% of the variability in nickel recovery and nickel product grade respectively was accounted for. Algorithms have been developed for Ni, Co, Mg, Al and Fe, which represents the revenue and operating cost factors for the process. The algorithms have subsequently been applied to the resource model, allowing prediction of elemental grade and recovery for the development of the mine schedules based upon these parameters and not head grades alone. This has allowed optimisation of the mine schedule for improvement to the project&apos;s NPV. Keywords: Ni Laterite, Prediction, Multiple Linear Regression, Beneficiation

Jan 1, 2004

By P. Schloth, H. van Swygenhoven, N. Chobaut, J-M. Drezet

"In the current trend toward thicker aluminium plates, a major concern is the stress build-up during quenching which causes distortions during machining. Indeed, cooling rates are not high enough, especially at the core of such thick plates, to prevent any precipitation and quench induced precipitates lower the hardening potential. Multi-scale modelling is required when predicting macro-scale stresses after quenching for thick heat treatable aluminium components. The reason is the instantaneous strong coupling between phase precipitation at the nano-scale and material hardening due to precipitation or softening owing to solute depletion at the microscale. For thick parts, quenching intensities decrease when going from the skin to the core of the component, thus introducing a gradient of nanostructure and consequently a gradient of mechanical properties. In addition, large thermally induced deformations lead to high macroscale residual stresses although part of them is relaxed by plastic deformation. These stresses have been measured in water quenched thick plates of 7040 and 7449 aluminium alloys using neutron diffraction and layer removal techniques and the results when compared with a thermomechanical finite element model of quenching highlight the influence of precipitation.IntroductionIn the processing route of heat-treatable aluminium alloys (AA), a critical step is quenching from the solutionizing temperature. High cooling rates are desired, as they avoid formation of coarse precipitates, which reduce mechanical properties. Fast quenching, however, cannot be achieved in the centre of thick components, where the quenching rate can be more than one order of magnitude lower than at the surface. The existence of a thermal gradient between core and surface leads to a differential thermal deformation which is accommodated by elastic and plastic deformation to comply with the compatibility of deformation. Whenever the material yields, especially at high temperature when the yield strength is low, residual stress remains after quenching due to the irreversibility of plastic deformation. After quenching, the plates are in a state of residual stress that causes unacceptable distortions during machining and may reduce service life drastically. Since stress relaxation is negligible during ageing treatments [1 ], agehardened aluminium parts are usually stress relieved prior to ageing. This is typically achieved by applying plastic deformation: stretching from 1.5 to 3 % in the rolling direction (L) can reduce the internal stresses by a factor of approximately 10 [2, 3]. However, complex geometries or thicker components like thick sheets require other approaches. Reducing the quenching rate by using boiling water for instance leads to lower residual stresses [1, 4]."

Jan 1, 2013

By K. Moriyamo

Operation improvement efforts at Hyuga Smelting Co., Ltd. have focused on calcining capacity in the reduction rotary kilns ("the kilns"), whose limited feed rate capacity had capped production at around 18,000t-NiN since 1995. To improve the kilns&apos; feed rate capacity of 80 wet t/hr, attempts were made to increase the gas flow in the kilns by increasing the capacity of the off-gas fans. However, as the increased gas flow resulted in only limited improvement of the kilns&apos; feed rate, a scoop feeder was installed on each kiln to add coal to the middle of each kiln&apos;s interior to gain a higher efficiency of thermal supply and conversion. With these gas flow and coal charge addition operations, the kilns&apos; feed rate capacity increased up to 120 wet t/hr, with burner fuel efficiency increasing by approx. 10% (approx. 5% in total with the additional coal included). As a result, production was raised to a level of 22.000t-Ni/Y Keywords: reduction rotary kiln, scoop feeder, additional coal charge.

Jan 1, 2004

By Junji Shibata

Waste solution from the Ni non-electric plating process contains 4.0 kg/m3 Ni, 0.1 kglm3 Fe, 0.0 I kg/m3 Zn, 48 kg/m3 S042-, 98 kg/m3 HP032-and 31 kg/m3 laetic acid as a typical composition. Solvent extraction, cementation, ion exchange resin and precipitation methods are possible to use for the treatment of this kind of solution. In this study, solvent extraction of Ni was investigated using two kinds of extractants to clarify the relation between extraction percent and pH for various extractant mixtures. As Ni ion has an octahedral structure with ligands, the synergistic effect for Ni extraction is considered to take place in solvent extraction using two types of extractants. The investigation of the synergistic effect for Ni extraction was carried out in case of various extractant systems.

Jan 1, 2003

By Ashwini Kumar

Flame impingement on the burden is routinely encountered during the initial phase of melting in aluminum reverberatory furnaces. This impingement causes an obstructed pathway for the hot gases, and hence the circulation and residence time of the hot gases are greatly impacted. Moreover, as the load melts, the flames gradually achieve an unobstructed path leading to reduced gas residence times. This flame impingement and constantly changing combustion space volume will lead to vastly different fuel and oxidizer mixing patterns and thus affect the overall furnace performance. Fine tuning the burner operating conditions such as flow rates and injection angles with the changing combustion space could result in significant improvements to the furnace efficiency. However, one has to gain a better understanding of the furnace dynamics to know the suitable parameters to adjust. Physical modeling can be elaborate and expensive to conduct on a regular basis while Computational Fluid Dynamics (CFD) can cost-effectively address this challenge. In this study, the furnace model is created with a particular loading pattern to understand the flame dynamics in the presence of a piled load. This configuration can be thought of as a computational model of the furnace with the burden at a particular stage of the melting process. Thermal efficiency and behavior of the furnace are quantified and the predicted values are compared with the operational data from an experimental reverberatory furnace.

Jan 1, 2008

By O. Norman Lotter

The formulation and use of mixed collector suites in sulphide flotation can be traced back as far as 1957 with the work of Glembottskii and his co-workers in Moscow. The subject was reviewed by Lotter and Bradshaw in 2010, and proposed a synergy between ideally-selected different reagent types to deliver improved performance, in particular the in situ catalysis of a xanthate to dixanthogen by a dithiocarbamate. Correctly formulated for a particular application, an optimally arranged mixed collector suite delivers the following improvements to the flotation process: • An increase in the flotation kinetics • Improvement in coarse, or middling, particle recovery • Reduction in total dosage requirement • Best results are found from testing the ratios of the collectors. This is of critical importance. In all an optimally formulated mixed collector system usually delivers an increase in paymetals recovery of 1–4% absolute, with a gain in concentrate grade in the range 10–20% relative. In recent years, the addition of semi-conductor theory and associated electrochemistry has contributed significantly to this toolbox by way of identifying optimum domains of Eh and pH for the flotation of individual minerals. In the case of mixtures of minerals, this is where the mixed collector system delivers significant value by way of presenting a mixed set of collector radicals and dimers in a common Eh and pH domain for overall performance. This calls on a fundamental understanding of organic chemistry, mineralogy, semiconductor theory, and electrochemistry. Whereas the selection of grinding media type effectively influences the Eh, the pH can be easily controlled by pH modifiers. The theory of this system, and some industrial case studies, are discussed.

By F. Qian

An impinging gas jet on a liquid surface is found in many industrial process systems such as electric arc furnace, welding, steel-making operation and others. Fundamental understanding of the interaction of a gas jet on a liquid pool can provide important insights into process behavior resulting in improved efficiency. A numerical model is developed for solving the flow fields of both impinging gas jet region and liquid pool below, in which the deformed interface shape is predicted simultaneously. Using curvilinear coordinates, the Navier-Stokes equations of each phase are solved separately through coupling of static pressure, shear stress and velocity at the interface. Several cases for jet distances and flowrates were investigated both numerically and experimentally with an air-water model. Favorable comparison of numerical results with experimental data confirms the validity of the present numerical approach. An existing phenomenological model for &apos;penetration depth&apos; prediction was extended for smaller 3et exit height to jet diameter&apos; ratios.

Jan 1, 1995