Search Documents

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The clean utilization of the residue containing chloride, CuCl residue, produced from zinc hydrometallurgy is very important for the recycle of valuable metals. And drying is the main process in recycling. In this study, response surface methodology was used to optimize operating conditions of the drying of CuCl residue in a convection oven and desirability function used as the methodology for the optimization. Optimization factors were air temperature (80–100°C), material thickness (10–25mm) and process time (80–120min) while investigated responses was final moisture content. The optimum conditions were found to be the temperature of 95.48°C with the material thickness of 13.47mm for the process time of 89.48 min. Under optimum conditions, the predicted moisture content of CuCl residue was 4.11% while the experimental date was 4.13%. The experimental value after process optimization was found to agree satisfactory with the predicted value. After drying, XRD was used to analyze the main phases of CuCl residue. The CuCl residue is made up of CuCl,Cu2O, ZnS and other compounds.

Jan 1, 2015

By Run Huang, Xuewei Lv, Lei Lei, Guibao Qiu, Chenguang Bai

"The TiO2-rich slag and pig iron can be produced from ilmenite concentrate by the electric furnace process. In this study, ilmenite concentrate was reduced in a vertical furnace equipped with a weighting data acquisition system. The effects of reducing agent (carbon) amount on the iron reduction were studied. The phase transformation, morphology and chemical compositions of reduced samples were investigated by X-ray diffractometry (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. It was found that the reductive degree of ilmenite concentrate increased with the increase of reducing time. The phases of reduced samples were mostly iron, rutile, Ti3O5 and Fe2TiO5. The mass loss percentage increased with increasing the carbon amount from 8% to 12%. When the carbon amount exceeded 12%, the mass loss percentage decreased with the increasing of carbon amount.IntroductionIlmenite and rutile are the main raw materials for producing titania pigment and titanium metal. With the development of the titanium industry, huge amounts of titanium resources are needed. As sources of high-grade titania mineral decrease worldwide, more attention should be paid to the processes involving low grade mineral such as ilmenite ore. In ilmenite, MgO and CaO are the gangue parts. Therefore, the ilmenite refining becomes more and more popular. In the previous studies, the methods of ilmenite refining are electric furnace smelting, direct acid leaching, selective chlorination and thermal reduction [1]. Electric furnace smelting method is widely used in the titanium industry, however, which consumes a great deal of energies and has a high CO2 emission. Its essence is to remove iron oxides and obtain a high titania slag. So the thermal reduction of ilmenite concentrate is an important step in titanium industry, which can decrease carbon reagent consumption and save energy.Over the past several decades, many studies have been carried out on the mechanism and kinetics of the reduction of different ilmenite ores, which are as follows: The carbothermal reduction of Panzhihua ilmenite initiated at about 860 oC. In the temperatures ranging from 900 oC to 1400 oC, the reaction rate was changed like a shape of “M”. That was to say that the reaction rate increased with the growth of temperature at first, then decreased, afterward increased again and at last the reaction was arrested [2]. The Mohammad A.R group [3, 4] showed that the carbothermal reduction of primary ilmenite concentrate was faster in hydrogen and initiated at a lower reduced temperature than in argon and helium. The reduction in argon and helium had about the same rate and extent. Titanium oxycarbide started at 1000°C in hydrogen. The conversion of primary ilmenite concentrate to metallic iron and titanium oxycarbide at 1200 °C was completed in 300 minutes. Monoxide as the reductant to reduce ilmenite had been studied intensively by a few research groups [5, 6]. The rate and the degree of reduction depended on the formation of a metallic shell of iron which inhibited the transfer of CO to the reaction zones; titanium had a strong effect on the mechanism and rate of reduction of iron oxides. Wang and Yuan [7] studied the reductive kinetics of the reaction between a natural ilmenite and carbon. At temperature below 1100°C, chemical reaction was the rate controlling step, at 1100 to 1250°C mixed controlling was rate controlling step, above 1250°C diffusion through the product layer controlled the reaction. Zhang [8] investigated the reduction of natural, sintered and preoxidized ilmenite concentrates in hydrogen methane mixtures. Preoxidation and sintering of ilmenite concentrates changed their phase composition and caused a sharp decrease in specific surface area of raw materials and an increase in carburization temperature. Sintering also increased the metallization temperature of iron."

Jan 1, 2011

By M. M. Monte

A method for removing metallic mercury from contaminated tailing, using the flotation process, is described. In order to define some relevant parameters for the mercury flotation system, microflotation and electrophoretic mobility tests were carried out on (pure) metallic mercury in the presence of several surfactants. Based on the results obtained from fundamental studies a series of bench scale flotation experiments with mercury containing tailings from two wetland sites in Brasil were done. The results of microflotation tests with mercury showed that by using cetyl trimethyl ammonium bromide, an increase in mercury flotability is observed in the acid pH range, whereas in the presence of potassium oleate the highest mercury flotability was found in the alkaline pH region. The mercury flotability using potassium amyl xanthate was improved by the addition at sodium dithionate as an activator. The bench scale flotation tests with contaminated tailings from Poconé (brazilian wetland site) showed a recovery of 70% when sodium dithionate was used as activator and potassium amyl xanthate as collector. The resulting coefficient of separation is around 60%. However, the results of the flotation experiments with fine fractions from amalgamation tailings from Peixoto de Azevedo (brazilian wetland site) showed a low mercury recovery (32%).The results from this work suggest that since in the Poconé site tailings, the metallic mercury is not completely associated to the finer particles, the flotation process to recover the metallic mercury seems very promisor.

Jan 1, 1996

By Shengfan Zhou, XUEWEN WANG, Bianfang Chen, Mingyu Wang

Vanadium was leached from roasted stone coal by NaOH solution, and the effect of leaching temperature, leaching time, addition of NaOH, liquid to solid ratio, the grinding fineness of stone coal, and stirring speed on the vanadium leaching rate was studied. The kinetics analysis for the process is presented by the shrinking core model. The results show that the vanadium leaching ratio of roasted stone coal can be beyond 75% at the 6% NaOH addition, leaching temperature of 95°C, leaching time of 7h, liquid to solid ratio of 1.2mL/g, and grinding fineness of 0.111mm. The leaching process is controlled by interfacial reaction kinetics and the apparent activation energy was 59.36kJ/mol.

Jan 1, 2016

By C. Mattich, A. L. Beyzavi

The Waelz Plant at Taiwan Steel Union Co. Ltd. (TSU) was erected within nine months from September 1, 1998 to May 15, 1999. The nominal capacity of the plant is 50,000 tonnes per year of electric are furnace dust (EAFD). The plant, consisting of material handling, a waelz kiln, a waste gas cleaning system, waelz oxide leaching and waste water treatment, was commissioned within three months from July 1, 1999 until October 12, 1999. The specific problem of the plant is the high chlorine content in the EAFD pellets which is up to 6 %. Lurgi Metallurgie GmbH, Frankfurt, Germany was responsible for the engineering erection and commissioning of the plant.

Jan 1, 2000

By Qian Li, Li-chen Hou, Yong-bin Yang, Tao Jiang, Jian-jun Hu, Bing Xu

Extraction of gold from refractory gold concentrates usually requires an oxidation step to remove arsenides、sulphides and carbonaceous matter. In this investigation, the gold concentrates were two-stage roasted under different atmospheres and temperatures. Results indicated that at the first stage, under neutral atmosphere, the removal rate of arsenic increases as the temperature rises. Under the oxidizing atmosphere, with the increase of temperature, arsenic content in the residued calcine increases, in addition, the volatilization of arsenic is also affected by the oxidation of carbon that generated CO, which is advantageous to the decomposition of arsenate decomposition. At the second stage of roasting, it is the higher temperature and stronger oxidizing atmosphere, the faster sulfur and carbon oxidated rate is, but at the same time, the calcine appears the phenomenon of consolidation because of the phase of silicate compounds generate.

Jan 1, 2015

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

"The effects of five commercially available foaming reagents (range of 0 to 25 ppm) namely Dowfroth 250, Saponin, Yucca, Licorice and Meta-Para Cresol on acid mist control, current efficiency, polarization behavior, and deposit morphology and orientation were investigated. The deposition was carried out using a bench scale electrolysis apparatus (cell volume 3L) at 500 Nm-2 and 38°C for 3 hours from Kidd Creek zinc electrolyte. The acid mist control capability of the various reagents was studied and compared by characterizing the foam layer generated during actual electrowinning conditions and by direct quantitative measurements of acid mist levels on top of the electrowinning cells. Within the range considered, the addition of these reagents reduced the current efficiency, refined the grain size of the deposit, and changed to preferred orientation of most of the deposits. Among the reagents tested, acid mist measurements indicated that Licorice and Dowfroth 250 were the best acid mist suppressant at emissions of 0.30 mglm3 and 031 mg/m3 respectively while Yucca and MPC produced the most mist at 3.0 mg/m3 and 33 mg/m3 emission rates, respectively.IntroductionMost of the world's primary zinc is produced via a combined roast-Ieach-purificationelectrowinning process. Depending on the electrolysis conditions, several additives may be added to the electrolyte. Some (e.g. glue, antimony, sodium carbonate) are added to mainly counteract the detrimental effects caused by impurities while others (e.g. licorice, Saponin) are used as foaming reagents to prevent excessive acid mist formation. Acid mist emission is a problem in many electrolysis operations because it corrodes the equipment and is a health hazard to the workers in the tankhouse as well as it pollutes the environment. Due to recent trends towards more environmental protection and more stringent in-plant hygiene, there is an increasing need to minimize these aerosols. In order to eliminate or minimize these aerosols foaming agents are usually added to the electrolyte to produce a foam layer on top of the electrolyte, thus trapping most of the mist. The ideal foaming agent would trap all of the mist and would not interfere with the electrowinning process. It is also evident that the reagent toxicology, cost and availability are important factors that need to be considered.Review of the available literature clearly indicated that very little work has been done in the past on the subject of acid mist control in electrowinning operations particularly in the area of foaming and anti-misting properties of surfactants. Two papers [1,2] have reviewed briefly the existing technologies for acid mist control. Recently, most of the work in this area has focused on the development of special mechanical devices that could be attached to the electrodes and control the mist generation at the source before it is emitted to the cellhouse [2-5]. On the other hand, extensive body of literature exists that deals with the effects of anti-misting reagents on the electrowinning aspects [6-7]."

Jan 1, 1997

By Dietrich Gross

This paper describes an advanced oxy-fuel combustion technology for re-melting aluminum that significantly reduces energy consumption and emissions. This oxy-fuel combustion technology developed by Jupiter Oxygen is a patented process for combustion of fossil fuels with pure oxygen while excluding air, thereby creating an undiluted high flame temperature and increased efficiency for process heating in industrial furnaces. This unique process has led to improved heat transfer and longer residence time while maintaining the same process temperatures as with air combustion. The energy efficient combustion process allows aluminum companies to operate at a substantially lower cost due to a dramatic fuel savings of up to 70% for natural gas and waste oil (1). The results of more than 10 years of day-to-day experience utilizing the Jupiter Oxygen Corporation oxy-fuel combustion technology licensed to Jupiter Aluminum Corporation in the aluminum re-melting business are discussed.

Jan 1, 2008

By E. N. Mounsey

Ausmelt Technology was selected by Bindura Nickel Corporation (BNC) as the basis for a new copper circuit to process nickel plant copper leach residue to blister, anode and finally cathode copper and recover PGM values at the Bindura Smelter Refinery (BSR). The process selected, based on Ausmelt Technology to smelt and convert the residue to matte and blister copper and produce a discard slag, is novel incorporating smelting, converting and slag reduction process steps in a single Ausmelt vessel. The process demands a high quality blister copper product with low levels of arsenic and nickel. This paper reviews the project and the initial operational results to the end of 1997 of the Ausmelt Top Submerged Lancing (TSL) smelter and discusses the implications for the wider TSL converter market.

Jan 1, 1998

By Geza Kisvarsanyi

Ore deposits composed of enargite, tennantite, gold, and pyrite have been mined in volcanic rocks of Oligocene age (35 m.y.) at Recsk, Hungary. Vertical and horizontal zoning of the alunitic-argillic alteration and of the ore minerals led to the concept of an intrusive heat source at depth. Subse-quent drilling disclosed a series of ore deposits in a zoned pattern in and around a stock, separated by a barren gap of 1000 meters from the shallow ore. The ore system is in a intracaldera horst-graben structure, formed by collapse and intrusion in a microplate subduction. volcanic-arc tectonic environment.

Jan 1, 1987

By Steve Johnston, Mowafak Al-Jassim, Fei Yan, Omar Sidelkheir, Alain Blosse, Katherine Zaunbrecher

"Imaging techniques are applied to multi-crystalline silicon wafers and solar cells throughout the production process. Photoluminescence imaging, both band-to-band and defect-band, is used to characterize defects and wafer quality at all process steps. These steps include bricks sawn from ingots, wafer sawing, cleaning and texturing, emitter diffusion, edge isolation and glass removal, anti-reflective coating/passivation, and metallization of finished cells. Bricks, wafers, and cells can be imaged at a rate commensurate with in-line measurement, giving spatial information to characterize quality and defect content. Photoluminescence images on silicon bricks can be correlated to lifetime measured by photoconductive decay and could be used for high-resolution characterization of material before wafers are cut. The defect areas in as-cut wafers are compared to imaging results from electroluminescence and lock-in thermography, and cell parameters of near-neighbor finished cells, showing correlations to efficiency, open-circuit voltage, and short-circuit current.IntroductionImaging techniques can rapidly characterize material quality and defect density. Photoluminescence (PL) imaging can be applied to silicon from the brick level to all wafer process steps [1-8]. At the brick level, material thickness allows for measurement and correlation to lifetime where surface recombination effects are minimized [6, 7]. At the as-cut wafer level where thin unpassivated wafers prevent accurate lifetime assessment due to surfaces, defects can still be categorized and quantified to predict finished cell performance [3-5]. Defect regions can be identified by recombination-limited band-to-band PL or by defect-band emission [9-12]."

Jan 1, 2012

By Lionel Ryan

In 1996, the Dominican Republic operation of Falconbridge (Falcondo) developed a 5-year Process Control Plan in conjunction with the corporate Process Control group located in Sudbury, Ontario, Canada. This plan was further refined into an analysis of the areas of the highest potential economic return for the company with the reduction shaft furnace operation being the most promising. Historically, the reduction plant, which comprises 12 shaft furnaces, has been the bottleneck of ferronickel production. Since 1996 there has been a history of control development, and the current status is that all 12 furnaces are using advanced model-based multi- variable predictive control. The combination of advanced process control (APC), improved control system performance and improved process information management has resulted in an increased throughput of 6% per shaft furnace and a reduction in operating costs of 4.5 US cent/lb of Ni. This paper reviews some of the major milestones that have been achieved in this development Keywords: Advanced Process Control; Model Based Predictive Control; Connoisseur, Reduction Shatt Furnace; Nickel Laterite Ore; Ferronickel; MonitorMV

Jan 1, 2004

By F. Qian

Direct impingement of molten metal baths by a gas jet is commonly encountered in such processes as BOF and electric arc furnace steelmaking. Shape and local fluid mechanics in the impinging region is important because it determines the interaction of the metal pool with the surroundings. Goal of the present work is to characterize and understand the interfaces at the impinging region. Using a physical model consisting of water/corn oil and water/kerosene as surrogates for metal/slag, interface shapes for slag-gas, slag-metal and metal-gas are investigated. Influence of transport properties of the two liquids on the shape and flow fields are also experimentally determined under various impinging jet conditions, namely jet momentum and jet height. The viscosity of the slag layer (corn oil or kerosene) has the most significant effect on the interface shape and the induced flow fields. The interface shapes were measured both photographically and by using a surface- tracking resistance probe. The limiting condition at which the jet breaks through the corn oil or kerosene layer and reaches the water layer was determined experimentally

Jan 1, 1994

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the furnace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By Xi-chang Shi, Yun-feng Fu, Bai-zhen Chen, Hui Xu, Xiang Xiao

"Extracting boric acid from saline brine by boron specific ion-exchange resin was investigated. Effects of resin amount, temperature, time and stirring speed on boron adsorption rate were studied in the experiments. The results indicated that the XSC-700 resin showed excellent boron absorbability and it performed better property for elution. The maximum boron adsorption capacity was 6.16 mg/ml in the optimum conditions: the resin concentration of 5 ml/(100 ml brine), the temperature of 60°C, the time of 5-6h and the stirring speed of 100 r/min. Boron was eluted from the resin with HCl and boric acid was crystallized by evaporating the eluate. The product of boric acid was in pure form as confirmed by XRD and other analysis techniques.1 IntroductionBoron has a number of minerals in nature such as tincal, colemanite, ulexite, and kemite, etc. [1-2]. Boron and its compounds are chemical materials of significant value. The principal industrial uses of boron compounds are in the production of glass, porcelain, enamels and detergents. Other uses include fertilizers, metallurgy, and nuclear shielding [3-4]. In recent years, because of the large-scale mining boron ore, ore resources are drained gradually. With the development of science and technology, the boron mineral resources will be unsatisfied with the future requirement. There exits abundant boron resources in salt lakes which cover about 40% of the total reserves in China. If we can obtain boron from salt lakes, it will produce great economic interests [5-6]. Therefore, actively seeking boron from salt lake and other resources in suitable conditions has become a hot spot in the research organizations of boron resources development and utilization in the world [7].There are many methods such as acid crystallization, solvent extraction and ion exchange processes suggested effective for boron extraction from aqueous solutions. Acid crystallization method has the shortcomings of complicated procedures, the pollution caused by hydrochloric and other ingredients returning to salt lakes during the extraction process. Although solvent extraction process increases the boron acid recovery efficiency, the cost of production is high [8-9]. However, Chelating resin extracting boron has the characteristics of simple process, easy operation and no pollution. It was reported that chelating resins containing functional groups show a high selectivity for boron extraction [10-12]. Therefore, ion exchange technique which is now the most practical application of significance and most extensively used ha"

Jan 1, 2011

By Douglas J. Harvey, Chi-Mou Ni

"This paper presents an analysis technique for the solidification of metal castings. This method, based on a modified finite difference scheme with an irregular mesh, is capable of dealing with the complex geometries of castings. The nonlinearities in material properties of specific heat and thermal conductivity, arising from the phase change during solidification, are accounted for in the step-by-step calculations. Two solidification problems are solved with this analysis technique and the calculated results compare satisfactorily with experimental data. IntroductionCasting process design engineers are often faced with the difficult problem of designing castings to be produced porosity-free. Since the solidification of metal is affected by many interacting variables such as the thermal conductivity, density, and specific heat of both the molten metal and the mold, it is easily seen why this is a difficult task.Typically, casting tooling design is an intuitive process which builds on past successful methods. After processing equipment is constructed, trial castings are made and examined for dimensions and integrity. Changes in the tooling are generally required to improve casting soundness or to reduce cycle time. In the permanent mold process, tooling is complex and difficult to alter after initial construction. The water-cooled steel molds are part of the complete automated system. Associated holding furnaces, pouring ladles, casting conveyers, and utility connections all make other than minor adjustments a costly and time consuming task. An analytical method for using the principles of heat transfer for predicting solidification patterns would be of great value in the permanent mold process by minimizing costly changes."

Jan 1, 1986

By Jun Chang, Jin-hui Peng, Jing Chen, Li-bo Zhang

The leaching of indium from refractory zinc oxide flue dust(ZOFD) is attempted to utilize microwave sulfating roasting process, followed by water leaching. The ZOFD and roasted product were characterized by XRD and SEM/EDS analysis. The effects of various roasting parameters, such as roasting temperature/duration, the proportion of sulfuric acid, as well as the leaching parameters such as the leaching duration and liquid/solid ratio, were assessed. The results indicate that nearly 97% of indium could be leached under the following conditions: mass ratio of concentrated sulfuric acid to ZOFD to be 0.5, roasting temperature of 150 ℃ and duration of 1.5 hours; while the optimal leaching conditions hold at temperature of 25 ℃ for 1 hour, with 4:1 of liquid/solid ratio. The indium leaching rate by the microwave roasting increased by 8% as compared with the conventional roasting process under identical conditions.

Jan 1, 2015

By K. D. Peaslee, V. L. Richards, C. H. Rawlins, S. N. Lekakh

"Steel-making processes generate carbon dioxide air emissions and a slag co-product. The aim of this project was to develop a functional sequestration system using steelmaking slag to permanently capture carbon dioxide emitted in steelmaking offgas. A possible parallel benefit of this process would be rapid chemical stabilization of the slag minerals with reducing swelling or leaching.This paper summarizes the original results of the project, including mineralogical and structural features of carbon sequestration with steel making slag, mathematical modeling of reaction phenomena using a modified shrinking core model, METSIM modeling of several possible industrial applications, a thermo-gravimetrical study of the reaction between slags and different gases, and design and testing for a lab scale apparatus consisted of two reactors.1. IntroductionThe U.S. produces 9-14 Mt of steelmaking slag annually, which represents approximately 10-15 wt. % of crude steel output.1,2 Primary uses for steelmaking slag include high quality mineral aggregate, Portland cement, unconfined fill, soil conditioning, and pH neutralization of abandoned mine drainage.3,4 The key factor prescribing slag use is the alkaline-earth metal (e.g. Ca and Mg) oxides content, which contribute to overall basicity and cementitious strength. However, as-produced steelmaking slag is chemically unstable. Calcium and magnesium oxides readily form hydroxides and carbonates through reaction with atmospheric gases. Both hydroxide and carbonate formation produce substantial mechanical swelling leading to heave failure in confined construction applications, thus many states dictate stockpile aging for 3-6 months prior to commercial use.5,6 Sequestration of carbon dioxide is a natural corollary to forced carbonation. The conversion of CaO/MgO to carbonates serves both to stabilize the slag, and permanently capture and store the CO2."

Jan 1, 2008

By Zhucheng Huang, Zhikai Liang, Lingyun Yi, Tao Jiang

"In this study, reduction of iron ore pellets was carried out at 800-950°C by simulating the atmosphere of typical coal gasification gas. The effects of temperature, gas composition and reduction degree on swelling were investigated respectively. Reduction degree was obtained according to the weight loss records. And volume changes of pellets during reduction were evaluated by infrared photography. Results showed that the pellet swelling increased with temperature and decreased slightly with hydrogen content in the reducing gas. The swelling peaked when reduction degree reached about 40% and then decreased to be stable finally. The microstructures of pellets during reduction were examined by reflected light microscope and relatively rational explanations were proposed for their swelling behaviors.PrefaceDirect reduction iron is an important and indispensable raw material for high-purified and high-quality steel in the electric furnace smelting. Gas-based shaft furnace direct reduction process has very strong competitative ability; however, this technique requires natural gas as reducing agent, so its development has been restricted by gas source and area. Compared with gas-based reduction method, coal based reduction method has the disadvantages of higher production cost and lower productivity. In China, coal resources are abundant and coal gasification technology is mature, and the development of coal gasification shaft furnace direct reduction process is promising. [1] The gasification methods of fixed bed method (Lurgi method), fluidized bed method (Undok method), airflow bed method (Texaco coal water slurry method and Shell dry powder coal method) have been put into use successfully. These syngas generated by different methods can meet the actual production requirement of shaft furnace. However, the compositions of the effective reduction gas in the syngas are quite different. The ratios of hydrogen and carbon monoxide (H2/CO) of Undok or Shell coal gas, Texaco coal gas and Lurgi coal gas are 0.4, 0.6~ 1.0 and 1.6~2.3, respectively. [2] In the coal gas direct reduction process, the swelling behavior of iron ore pellets is various due to the differences of the gas composition, reduction temperature and reduction degree, and it seriously affects the normal operation ofDRI production. [3-9] Therefore, the research on the swelling behavior and its mechanism of iron ore pellets in direct reduction were carried out in this paper."

Jan 1, 2013

By Guangliang Wu, Dongchang Huang, Xinbin Liu

Oxidation Kinetics of SPHC was analyzed by TGA, and the curve of oxidation weight gain with different temperature was acquired. It is found that, when the oxidation temperature is between 500 and 600 , all the curves are linear; when the oxidation temperature is above 700 , the curves are close to parabolic. At the temperature of 900 , the oxidation weight gain increases dramatically. The TGA results indicate that the activation energy of SPHC steel is 146.19 kJ/mol at the temperature of 500 900 , and an oxidation kinetic model was set up for variable temperature. Based on the temperature change during rolling process, numerical simulation of oxide scales evolution was carried out for SPHC steel, and the simulation result agreed well with measured ones. It can provide a basis for estimating the scale growth and controlling the temperature on site.

Jan 1, 2016