Search Documents

By R. Hemp

This paper describes work carried out to obtain a heat balance in the B3 shaft longwall stope at Blyvooruitzicht gold mine. Recordings were made of the temperature of the air and chilled water entering and leaving the section during three periods, August 1 September 1977, November 1 December 1977 and March 1978. These recordings, together with numerous other measurements were used to determine the rate at which heat was being removed from the section by the various fluids flowing through the section. The rate at which heat was entering the section was then calculated, by considering each source in turn. These two sets of figures made it possible to draw up a heat balance, and also obviously gave vital information on the magnitudes of the various heat sources and on the methods used to remove heat. In general reasonable heat balances were obtained, the errors being in the range -6 per cent to +22 per cent.

Jan 1, 1980

By J. P. Savely

This paper describes the development of a trim blast design to improve the stability of a final pit wall. Description is given of the effects of rock characteristics, rock type, and pit plans on the blast design. Currently, six benches have been mined with trim blasting. A more stable final wall has resulted and the successful program has reduced mining costs over an extended time period. Low-cost blast monitoring and field observation were used to determine peak particle velocity and blast damage. Using criteria developed from this relationship, trim blasts were designed and evaluated.

Jan 1, 1987

By C. J. Savage

Rio Tinto Minera, S.A. operates in Southern Spain, at one of the most ancient mining sites in the world, using advanced computerised mine planning. This paper describes the development and application of the mine planning systems to the copper and gold/silver operations. It briefly covers the hardware configuration, and the advantages and improvements in mine planning achieved. The system's application started with the long term mine planning of Cerro Colorado (open pit) copper mine and was gradually extended to cater for the medium and short term planning requirements of the other operations of the Company. The base of the system is a mineral inventory established by the combined use of the geology and geostatistical methods, and compatible with the mine planning requirements. The planning system has three major components: one used for open pit design and long term mine planning, another used for blast evaluation and finally one used for short term mine planning. Recently, a fourth component has been added to the system for reconciliation between predicted and actual tonnages and grades. There is common data file transfer throughout the system.

Jan 1, 1986

By J. G. Jenkins

Magma Copper Co.'s San Manuel solvent extraction/electrowinning (SX-EW) facility has operated since May 1986. The original facility had a design capacity of 22.6 kt/a (25,000 stpy) of electrowon copper cathode produced by processing pregnant leach solution from an open pit-heap leach operation. In 1988, the plant was expanded to 45.3 kt/ a (50,000 stpy) to incorporate processing in-situ leach solutions. This pager focuses primarily on the heap leaching area with regard to exploration, testing, feasibility, permitting, design and construction, and operating practices. Research using surfactant leaching aids to enhance copper recovery is also discussed.

Jan 1, 1995

By David G. Laughton, Richard Poulin, Michael R. Samis

Real options (RO) valuation is an alternative net present value (NPV) framework that is able to incorporate both management flexibility and dynamic project risks. In this paper, management is considering the development of a satellite low-grade zone while operations in a developed high-grade zone continue. If the low-grade zone is developed prior to high-grade zone exhaustion, mine capacity must be expanded before additional production from the low-grade zone can be processed. This expansion can be avoided only if low-grade zone development is delayed until the high-grade zone is exhausted. The RO model presented here allows the development and capacity expansion decisions to be reconsidered on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably.

Jan 1, 2002

By A. C. T. Bigg, A. F. Colombo, A. R. MacPherson

The step-by-step study of the Stronsay ores follows the testwork through the initial determination of Bond Rod and Ball mill work indices, the MacPherson Autogenous work indices and the production of a preliminary flowsheet. These results are then used to design a pilot plant program to test the effectiveness of fully autogenous primary and secondary grinding and to determine the feasibility of controlling feed rate by the use of variable speed mill drive and/or varying the mill load. A final flowsheet is recommended with mill sizes and power requirements.

Jan 1, 1992

By R. J. Puchala, B. M. Hawrylewicz

High voltage electrical discharge in water causes instantaneous release of accumulated energy into water. The experiment described in this paper regards the utilization of the electric discharge phenomenon in rock splitting. The pressure in the shock waves created by the discharge inside a small volume of water enclosed in solid rock causes stresses which can result in breakage of rock. Holes drilled in tested samples were notched in order to weaken the tensile strength of the rock and achieve a uniformly directed split. The influence of the notches was theoretically analysed and compared with experimental data. Results of the tests have been statistically elaborated in order to correlate the newly-created surface to the energy supplied.

Jan 1, 1986

By J. -C. Roegiers, M. Thiercelin

Accurate toughness determinations are difficult to achieve in the case of soft or heterogeneous rocks. The existence of a large process zone ahead of the crack tip makes the determination of the apparent toughness crack length dependent, in the case of subsized specimens. In order to use practical size specimens, the authors propose a new toughness test, the Modified Ring Test, which pre- vents a largely developed process zone to form ahead of the crack tip. This test has also the advantage that its geometry is core-based. Numerical and experimental results are discussed.

Jan 1, 1986

By Palmer C. Sweet

Mining-related wastes, which are increasing, are being utilized more and more as valuable resources in Virginia. The Environmental Protection Agency (EPA) divides mining-related wastes into two categories: those generated from mineral extraction and beneficiation and those generated from mineral processing. Materials from both categories are produced in Virginia, where waste (by-product) materials are present at a variety of mining sites and processing plants; some of which have been exploited for various uses in the past and/or present. These materials include: used concrete recycled for roadbase material; pyrite coated with magnetite for use in portland cement; minor amounts of fly ash for use in concrete block, lightweight aggregate, and flowable structural fills; granite and diabase quarry fines for use as agricultural and asphalt filler; lime kiln dust for use in neutralizing and stabilizing coal refuse; soapstone aggregate for use in terrazzo heat retention panels; kaolin for use as a filler product and as an ingredient in white cement; slate quarry fines used as landcover and combined with aggregate for crusher run and as a filler in asphalt; and coal refuse for use as fuel in a lightweight aggregate plant. There are some materials available that have never been utilized, although several ideas were investigated to turn them into usable commodities. One such material is a high-alumina scrap produced as a by-product at a ferrovanadium processing plant. However, large quantities of waste materials from metal mining, industrial mineral, and fossil fuel operations remain to be disposed of in an environmentally safe and economic manner. In 1989, almost one million tons of fly ash were produced from burning of coal at eight coal-fired power plants in Virginia. Present uses for this waste such as an ingredient in concrete block, concrete aggregate, and in structural fills cannot dispose of all the available material; however, increased use of fly ash as a soil/rock substitute for structural fills and embankments may solve the problem of its disposal. Another waste material is calcium carbonate precipitate paste produced at a lithium carbonate processing plant and presently being used for back filling an on-site inactive underground limestone mine. Flue gas desulfurization (FGD) wastes in the form of CaS04 will probably increase threefold. If this material contains a minimum of 95 percent gypsum and negligible chloride, it may have a value to a wallboard manufacturer as we move toward the year 2000. Thought must be given how this increasing waste can be disposed of in an environmentally safe manner.

Jan 1, 1995

By Gerhard Mücke

Geothermal and operational reasons in the German coal mining industry make it necessary to an increasing extent to climatize coal faces and headings by means of refrigeration plants. Air coolers installed on coal faces as well as in gateroads play an important part in such climatization. They must transfer, under difficult conditions, the refrigerating capacity supplied by central or de-central refrigeration plants from the chilled water to the air in the workings. The performance data of two new types of coalface coolers and of two different types of gateroad coolers were measured in two testing stations under different thermo- dynamic conditions with dust-free fresh air. As air coolers must be installed particularly at working points with a high .dust load the heat exchanging surfaces are fouled for the most part causing an essential reduction of the refrigerating capacity. The investigations therefore were extended to measurements with a certain dust load in the intake air of the coolers.

Jan 1, 1980

By S. K. Mishra, S. B. Kanungo, D. Biswal

Jigging of the -2.8 +0.7-mm size fraction of a friable, low-grade manganese ore sample from Andhra Pradesh increased the Mn content of a concentrate by 7% to 8%, with an average recovery of 57%. The jig concentrate was mixed with the unjigged -0.7-mm size fraction and ground to -150 µm. The sample was then subjected to wet high-intensity magnetic separation (WHIMS). The magnetic fraction thus obtained showed an increase in Mn content of 6%, but with an overall recovery of only 50%. The results of hydrocyclone classification of -150- µm ground ore indicated that the method is not capable of upgrading the manganese content, as both ferromanganese oxides and aluminosilicate gangue minerals constitute the fine size fraction. However, when the nonmagnetic fraction obtained from the WHIMS of -150- µm ore is subjected to hydrocyclone classification and the underflow obtained is subjected to WHIMS again, an overall recovery of about 50% to 52% is obtained with at least a 7% to 8% increase in the Mn content of the product. The phosphorus content in the product is not reduced by either of the two combinations of methods. The complex association of phosphorus with all the major phases in the ore has been clearly demonstrated from the linear correlation between the distribution ratios of major constituent phases and phosphorus.

Jan 1, 2000

By Kenneth N. Weaver

Introduction and Historical Background State Geological Surveys have been deeply involved in industrial minerals from their inception beginning in the first half of the 19th Century. To Massachusetts belongs the credit of having carried out the first Geological survey under state auspices on the Western Hemisphere. One of the causes leading up to this survey was. Governor Lincoln's message to the legislature of May 29, 1830, from which I quote in part: "Much knowledge of the natural history of the country would thus be gained (from a geological survey), and especially the presence of valuable ores, with the localities and extent of quarries and of coal and lime formations, objects of inquiry so essential to internal improvements and the advancement of domestic prosperity, would be discovered.". Similar phraseology is present in practically all of the initial organic acts creating the first State Surveys. High on the list of priorities for these embryo surveys was an inventory of the mineral resources of the State with particular emphasis on the industrial minerals. Prom these early beginnings, the state surveys have developed a great wealth of geological data either directly or indirectly relating to the development of mineral resources. One can gain some conception of the effort that state surveys today place on industrial minerals studies by noting the projects in which they are engaged as reported in the State Geologists Journal. In 1970, for example, approximately

Jan 1, 1972

By D. W. Fuerstenau, G. S. Sudhir, P. C. Kapur

Quartz-limestone feed mixtures were ground in a laboratory-size, choke-fed, high- pressure roll mill. As compared to individually ground minerals, the harder component (quartz) in the product mixture is coarser, and the softer component (limestone) is finer. An energy split index is introduced for quantifying the disproportionate split of the mill energy between the feed constituents. This index is incorporated into a grinding kinetic model for simulation of the product size distributions of the mineral components as a function of energy input to the mill. The self-similar character of the size distributions is analyzed and an energy-size reduction relationship for the roll mill is highlighted.

Jan 1, 1992

By Neville G. W. Cook, John Kemeny

Utilizing the principles of elastic-brittle fracture mechanics, stress-displacement relationships are derived for an elastic solid containing a slip plane consisting of various configurations of collinear arrays of cracks. These models take into account the heterogeneous nature of slip planes as observed in the lab and in the field, and are relevant to the behavior of rock containing faults, joints, bedding planes, and fractures. All of our models exhibit slip weakening behavior, and show regimes of both stable (aseismic) and unstable (seismic) deformation. For given configurations of cracks and applied boundary conditions, our results show explicit ly the energy released through unstable crack growth. For instance, it is found that two equal length cracks growing together release more seismic energy than, say, a large crack growing into a small crack. Also, by allowing cracks to coalesce, our models show multiple stick-slip events without crack healing or other geochemical means.

Jan 1, 1986

By S. Chander

The use of various electrochemical techniques to study mechanisms of sulfide mineral- flotation reagent interactions is briefly reviewed in this paper. Prior to such studies it is desirable to thermodynamically determine solution conditions favorable for formation of hydrophobic species deemed to be responsible for flotation. The thermodynamic equilibrium involving both the stable and metastable species can be conveniently represented by an Eh-pH diagram. Thermodynamics can also be used to predict conditions where a mineral might not float if depressants are present. Under favorable conditions of flotation there is competition between reactions leading to formation of hydrophobic species with reactions that lead to formation of hydrophilic species. Due to the sluggish nature of the reactions involving sulfide minerals, a knowledge of the kinetic behavior of the system is necessary. Electrochemical methods of investigation are wed in laboratory studies to (1) control the state of oxidation, (2) determine the type and amount of electroactive species present at the mineral surface, and (3) study kinetics of electrode processes. By combining electrochemical techniques and wetting measurements the identification of hydrophobic species that might be present at the mineral surface could be achieved. Both contact angle measurements at mineral electrodes or flotation in a cell equipped with a particulate bed electrode can be used for the wetting measurements.

Jan 1, 1987

By Roshan B. Bhappu, Sukhendu L. Barua

The economics of developing and operating small precious metal mines are unique and require much more scrutiny than larger mines since a limited tonnage must carry a heavy burden of capital investment as well as operating cost per unit ton to be mined and processed. Moreover, potential operators of small mines do not have the required expertise available to critically evaluate the technical and economic aspects of their projects. In this paper, the authors have attempted to provide technical and economic guidelines for developing and operating small precious metal mines. Capital and operating cost estimates as well as return on investment are provided for various scenarios utilizing different mining and processing techniques.

Jan 1, 1987

By R. L. McNearny

A comparison study was conducted between an actual physical model and a numerical model based on the physical model of the block cave mining method. Results from the numerical analyses closely simulated the blocky behavior of the physical models, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1997

By N. L. Weiss

General The crushing of run-of-mine hard rock ores is the province of jaws and gyratory primary crushers described in the two preceding chapters of this section. While it is now seldom difficult to make a choice between the two to suit a specific set of circumstances, the governing factors merit a review, and that is the purpose of this chapter. For every size of feed there is a crusher of either type that can handle it, and it is only when the desired crushing rate in toss per hour is considered together with the rock size that the preference for one type over the other is truly significant. When Taggart completed his Handbook of Mineral Dressing there were already in opera-

Jan 1, 1985

By John Durkin, Steven Wirch, Fred N. Kissell, Steven Ruggieri

The Bureau of Mines has developed two expert systems to give advice on coal mine dust control, one for continuous miner sections, and another for longwalls. Prototype versions have been evaluated by coal operators and MSHA. Both systems query the user as to the nature and extent of the dust control problem. Typical questions asked deal with matters such as cutting sequence, current dust standards and characteristics of current dust control techniques. Advice given by the system generally does not focus on a single issue, but may suggest a variety of approaches consistent with the ability of the operator to practically implement what is suggested. Both were written using expert system development software called Insight 2+. The advantages of Insight 2+ for the user are: low cost, IBM-PC compatibility, and the fact that little prior experience with computers is required. For the developer, Insight offers an easy to use production rule language and goal driven structure as well as a wide variety of capabilities.

Jan 1, 1987

By D. G. Foot, J. D. McKay, R. A. Ynchausti

The increasing popularity of column flotation as an efficient and profitable mineral beneficiation technique has resulted in the need to perform a study of basic column operating parameters in order to understand mineral behavior in a column. Variation of column rougher flotation parameters on the Nevada Fish Creek fluorite and Utah Collins manganese ores enabled characterization of four beneficiation zones within a column flotation cell. Although specific mineral behavior in each zone was peculiar to the mineral system involved, particle retention time predominantly affected both manganese and fluorite recoveries in the collection zones of the column while enhancing mineral grades in the cleaning zones. Column parameters such as column length, feed injection location, and tailings recirculation velocity were inherently linked to particle retention time and retention time distribution, both of which affected mineral recovery. Froth depth had a discernible effect on fluorite concentrate grades; as froth depth increased, fluorite grades increased. Wash water additions affected both fluorite and manganese recoveries and fluorite grade. Axial mixing drastically reduced fluorite and manganese recoveries due to short circuiting of some of the feed slurry in the column.

Jan 1, 1988