Search Documents

By Daryl E. Radcliffe, Raymond M. Stateham

The Bureau of Mines, under a Cooperative Agreement with the Bear Coal Company, Somerset, Colorado, conducted a large scale evaluation of the effect of time lapse on roof stability. Time lapse in this study is the interval between exposure and permanent support of the mine roof. The study indicates that time lapse is not a critical factor in roof stability provided permanent support is installed before catastrophic failure begins. Concurrently with the time lapse study, investigations were made of stress distribution around resin-grouted bolts, the regional stress field, and anomalous geologic conditions. The behavior of the resin-grouted bolts, at least in the Bear mine, appears to fit the Coulomb-Navier Theory. Geologic conditions are primary factors in trends of roof stability that extend across the mine.

Jan 1, 1982

By John E. Rourke, O&apos

This paper describes some of the results of a project for the design and demonstration of subsidence monitoring systems for underground coal mines. The project was designed to test monitoring systems described in an earlier feasibility report (O'Rourke and others, 1979). General objectives of the project were to develop reliable cost- effective monitoring systems for use above caving- type mining operations, over supported mines, and in urban undermined areas. Topics selected for discussion in this paper include a description of the instrumentation systems, the site conditions, problems of installation, resulting recommendations and an over- view of subsidence performance data obtained. There were some particularly difficult problems of installation to overcome at this site. Some of these could be experienced at any surface or under- ground project, others are probably more directly related to Western coal fields. Almost any subsidence monitoring program may face the following difficulties:

Jan 1, 1982

By Jean Habimana

Complex and distinct geological units spread along the 7-mile long 30-ft inside diameter Upper Rouge Tunnel CSO Control Project in Detroit, Michigan. Its construction is divided in two tunnel construction packages: The South Tunnel, to be driven in finely laminated weak TG Limy Shale, will be excavated by a shielded TBM with precast concrete segmental lining, while the North tunnel, predominantly in a relatively more competent geologic formation Antrim Shale, will be excavated by a main beam TBM with a two-pass lining system. The adits and deaeration chambers will be excavated by sequential excavation method. This paper addresses the process of selecting excavation methods and lining systems for shafts, tunnels, connecting adits, and deaeration chambers.

By Robert J. Rothwell

Underground mining of coal by longwall mining methods has not been a predominant technique in Ohio. To date, only five mines in the state utilize this method, however, the technique has sparked a certain amount of controversy. As a mining technique, longwalling was introduced into southeastern Ohio in the early 1970's but it did not attract public attention until the mines began moving into privately held surface lands. This occurred coincidentally at about the same time that the state of Ohio began to regulate the environmental impacts of underground mining. Prior to the passage of the Surface Mining Control and Reclamation Act in 1977, (SMCRA), Ohio's reclamation law, Chapter 1513 Ohio Revised Code (O.R.C. 1513) did not regulate underground coal mines. As a result of SMCRA, the Ohio Statute was amended in 1978, to include regulation of the surface effects of subsidence. The inevitable result was that existing mines were immediately subject to regulations that were not considered during the initial mine planning process. (For an excellent survey of Ohio Laws that deal with coal mine subsidence, see Zima, 1985. ) The problem faced at that time by both the coal industry and the Ohio Division of Reclamation (the agency within ODNR charged with implementing O.R.C. Ch. 1513.1, was that of attempting to superimpose permitting requirements, and design performance standards onto mines that' had been operational for a number of years.

Jan 1, 1986

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Anastasia Xenaki, Edmundo Laporte, Antonio Nieto, Jesus Castillo Gomez, Oscar Velasquez

It is particularly challenging for the mining industry to create and implement an efficient and adaptable mining innovation model to secure the continuous improvement of processes and products via technology. Human resource departments must play a vital role in shifting the mining culture, enabling these new classes of digitally skilled professionals to manage the mining operations of the future. This paper proposes the implementation of a concept based on the 5S mining innovation model ((a) Nieto, 2019), in a coal mining project in Central Asia, Mongolia. Practical and empirical evidence suggests that the model could serve as a roadmap to developing technologies and methods for the mines of the future.

Feb 1, 2023

By Thomas F. Connors

The end of an era is here. The pony-express era of industrial relations in the coal industry is ending. Those professionals who know it must end to insure the industry's future are happy, relieved, but somewhat saddened. They are sad because it did have its elements of suspense, thrills, frustrations, and at times, plain fun. The days of the Company town are ended; the wildcats are declining; violence (while a big part of today's industrial relations) is beginning-to decline. The spirit of sound industrial relations is beginning to take hold. This has to happen for the industry to compete in today's economy and it is causing major changes for those who have grown accustomed to the pony-express type industrial relations.

Jan 1, 1981

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are some- times large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy Bureau of Mines- sponsored subsidence study at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County) , West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar re- treat mining. Findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water levels at shallower depths. Post-mining values of hydraulic conductivity were typically somewhat higher than pre-mining values. Changes in water chemistry associated with mining were not sufficient to render the water unfit for human consumption.

Jan 1, 1986

By Mark Rybak

On August, 31, 2006, Tropical Storm Ernesto hit the City of Richmond, Virginia. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This case history describes the fast track design, bidding, and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft sinking methods, and final lining design all contributed to the success of this project. The storm inundated Richmond, Virginia with up to twelve inches of rain in some areas causing widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed causing local combined sewer and storm-water flooding. The collapsed sewer was an 8'-3" wide by 9'-6" high arch sewer that was constructed in the nineteen twenties and later filled over with municipal solid waste and a soil fill cap to current elevations. A sinkhole was created in the area of collapse approximately sixty feet deep and one hundred feet in diameter causing the existing arch sewer to become blocked. As a result of this blockage contaminated flood waters reached depths in low lying areas in excess of twenty five feet. [ ]

Jan 1, 2008

By J. Mark Richardson

The use of an integrated software package to simulate and optimize the performance of mineral processing circuits is illustrated by three examples. Each represents application of the software and associated techniques to optimization of an existing plant. In the first example, a South-western U. S. copper company employs the method to simulate and improve performance in crushing, screening and SAG milling. A second copper producer evaluates equipment changes and flowsheet alternatives in a closed-circuit ball mill-cyclone operation. A Southeastern U. S. aluminum refinery optimizes performance of a dry milling and classification circuit for production of carbon particles used in anode casting. Graphical and tabular data describe the circuits simulated and the results achieved in each example.

Jan 1, 1990

By M. P. Hoffman

The U.S. Bureau of Mines is developing a roof bolter with a computer-controlled drill head that will increase the safety of roof bolting in underground coal mines by allowing miners to be relocated to a safe area. To ensure secure anchorage, acceleration and strain data are broadcast from an instrumented drill steel to a data acquisition system. These data are analyzed, correlated, and transformed to pro-vide information about roof strata, then are sent to a supervisory computer executing National Institute of Standards and Technology's real-time control software. The supervisory computer sends setpoint commands to proportional-integral-derivative control loops to control drill thrust, position, revolutions per minute, and torque.

Jan 1, 1994

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009

By E. Petrakis, K. Komnitsas

The main objective of batch grinding modeling is the estimation of the product particle size distribution over time or specific energy input to the mill. So far, the developed analytical methods require often complicated calculations which are timeconsuming. Thus, more simple approaches that allow the reliable prediction of the complete product size distribution need to be developed. In the present paper, an approach, based on the population balance model (PBM), that reliably predicts the product size distribution is proposed. In order to enable this, the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (R-R) distribution, thus allowing the determination of the breakage rate for each grinding period. A time-dependent breakage rate framework was developed where the traditional linear theory of the PBM is considered a partial case. This approach allows the deviations from the linear theory to be categorized and the degree of the acceleration-deceleration of the breakage rate to be predicted. Modeling results were validated by laboratory grinding studies using two homogeneous materials, quartz and marble, and one heterogeneous, a limonitic laterite. The experimental data revealed that grinding exhibits non-first-order behavior and the degree of deviation from the linear theory depends on the tested material. The reliability of the proposed model was validated with the use of the distribution modulus n, the a value of the breakage rate parameter, and the optimum n values that minimize the sum of the differences between the experimental and estimated particle size distributions.

Feb 8, 2021

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

By B. Valentim

Policies for reducing NOx emissions have led power plants to restrict O2, resulting in high-carbon fly ash production. Therefore, some potentially useful fly ash, such as the economizer fly ash, is discarded without a thorough knowledge of its composition. In order to characterize this type of fly ash, samples were collected from the economizer of a Portuguese power plant burning two low-sulfur bituminous coals. Characterization was also performed on economizer fly ash subsamples after wet sieving, density and magnetic separation. Analysis included atomic absorption spectroscopy, loss-on-ignition, scanning electron microscopy/energy-dispersive X-ray spectroscopy, optical microscopy, and micro-Raman spectroscopy. Key words: Fly ash; Petrology; Petrography; Economizer fly ash

Jan 1, 2009

By J. P. Kennedy, O. A. Bascur

Large metallurgical complexes have more data than a small city and these data change as internal and external conditions evolve. Staffing turnover hinders experienced-based decisions especially with simple tools like spreadsheets. Lack of current information can contribute to decisions that result in significant deterioration in the quality of operation. Timely, unified information from sophisticated analyses presented to the broadest possible reach will improve operation. The major innovation is the addition of the web browser to the suite of software people will use with no training – the other two are spreadsheets and graphical presentations – and the consistent organization and transformation of the real time data to support broad access. This paper describes the data transformations and presentation methods necessary for a Web view, especially the special needs of real time data and analysis required for active operations decision-making. Many people inside and outside the complex, not just operators, need timely information that is abstracted, aggregated, organized and unified. Unification and aggregation of real time data presented via the Web opens a new paradigm for collaboration. The analysis tools are as important as the data. These rule-based tools add significantly to the operations database in the form of results stored for viewing with plant data. Mining and metallurgical plants already use many sophisticated analysis tools such as predictive maintenance policies based on statistical analysis vibration analysis, and oil and lube analysis for critical equipment. These add real time events, similar to an alarm package, and unified production information to the operational database. Simple models are used on line to create key indices that provide a real time indication of performance. Key indices include metrics for losses due to plant availability, performance efficiency, and overall process equipment effectiveness. These additional data in the operations database are used for early fault detection, increased production, better quality, higher availability of equipment and faster detection of process bottlenecks. An important feature is the ability for people to create their own key indices and store the results for use by anyone in the plant historian, but accessible by a browser. Keywords: plant information, principle components analysis, data reconciliation, gross error estimation, Internet, Word Wide Web

Jan 1, 2002

By Matthew E. Fowler

The Central Subway will extend the recently completed 8.2-km long Third Street Light Rail line another 2.7 km north through the Union Square shopping district to Chinatown with a concourse-to-concourse connection to the Powell Street BART Station. One mined and two cut-and-cover subway stations are planned. Particular challenges include: tunneling under existing tunnels; variable ground conditions ranging from saturated alluvium to fractured bedrock; a congested urban setting and large-span caverns. This paper gives an overview of the project as it stands midway through the preliminary engineering stage along with a discussion of the rationale and design approaches that are being used to address the construction challenges of restoring light rail service in the most densely developed areas of San Francisco.

Jan 1, 2008

By Steve Kral

Led by a surge in coal production and prices in recent years, Colorado’s mining industry is taking part in the same revival as others states and the world. Not too many years ago, the state’s industry was languishing in the same doldrums as the rest of the mining world. Ironic for a state whose history was based on mining. Now, however, Colorado’s mining can boast increased production in all commodities produced, along with prices that allowed companies to expand, increase work forces and post improved shareholder value. So there was a lot of optimism at the Colorado Mining Association’s (CMA) 107th National Western Mining Conference in February. The conference, held in Denver, attracted more than 500 attendees and 39 exhibitors. The theme was Colorado Mines the World.

Jan 1, 2005

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

By Sunny Schoone, Maximilian Getz, Felix Leaman, ELISABETH CLAUSEN

Jan 5, 2023