Search Documents

By Georgios Kafantaris, Carsten Bonde, Nataša Katic

Within the investigation works for the Copenhagen Cityring metro, Geo/CMT have carried out 90 geotechnical boreholes. Together with the previously available investigation, this resulted in more than 15 km of vertical drillings and several thousands of laboratory tests. The design is made for 17 stations, four shafts and two parallel 16 km long tunnels. The geotechnical investigation and design have been carried out in several stages comprising appropriate refinement of structural design and design of excavation operations, including TBM break-in and launching operations at each station shaft. Acceptance of the solution and / or refinement of the investigation and design schedule in the next stage were based on the geological conditions, area availability at surface level, planning and cost-control criteria. The applied recursive design refinement is presented herein with an example of the Østersøgade shaft location.

Jan 1, 2016

By P. J. Ryan

December 1988, Phelps Dodge Corp. brought an underground gold mine into production in the republic of Botswana. The mineralization is associated with steeply dipping shear zones in Archean greenstones of the Tati schist belt. The gold is intimately associated with sulfides and is refractory in nature. The deposit is being exploited by underhand open stoping methods. Vertical and inclined shafts are used to hoist the ore to the surface where it is treated by conventional crushing, milling, and flotation, followed by fluid bed roasting with cip elution and carbon regeneration. Adjacent deposits are being explored with a view to increasing production. Legal and taxation aspects of operating in Botswana are discussed.

Jan 1, 1991

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

By L. W. Saperstein, R. J. Sweigard, D. L. Simpson

Deep tillage is widely used as a means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids produced during deep tillage in order to prevent any significant recompaction from occurring. Various amendments were injected into the soil during laboratory tests using a small-scale ripping and injection system. Measurements were made of selected soil proper Pies to evaluate the feasibility of this method.

Jan 1, 1994

By S. Siewierski, L. Wojno

INTRODUCTION Bumps are among the most dangerous hazards in the Polish copper ore mines. Their occurrence is the result of the dynamic processes in the rock mass caused by natural factors connected with the deposition of strata and, to some extent, by technological factors resulting from the process of exploitation. In this connection, in order to ensure worker safety and choose such a technology that allows an achievement of high technological and economical parameters, a detailed knowledge of the phenomena occurring in the rock mass is required. In copper mines the basis for forecasting and control of bumps is obtained by continuous measurements and observations of the symptoms of rock mass pressure, the analysis of which ensures the accuracy of forecasting and points toward preventive means that must be applied to prevent bumps. The methods most often used for preventing bumps in copper mining are discussed in this paper.

Jan 1, 1982

By J. A. Herbst

Grinding circuits employed in mineral processing operations are designed to produce feed materials for beneficiation steps such as flotation and magnetic separation, which are sufficiently fine to achieve good liberation of valuable minerals from gangue without over- grinding. In many respects, grinding is the most important unit operation in a mineral processing plant. If adequate liberation is not achieved during grinding, subsequent separation steps will yield low metallurgical recoveries and/or product grades. Grinding energy requirements and operating costs typically exceed 50% of the total expenditures of the entire plant. Because grinding is an inherently energy intensive process and grinding circuit capital and operating costs are high, it is essential that such circuits be run as efficiently as possible. In- creased efficiency in grinding usually translates to a decrease in the energy required to produce a metric ton (short ton) of product size material. It is generally accepted in the mineral industry that efficient grinding circuit performance can not be achieved without the use of some form of automatic control. This is true because all circuits are subject to random disturbances which, if left unchecked, will upset circuit performance and rob a plant of productivity. Such disturbances arise from a variety of sources including natural variations in ore characteristics (particularly hardness changes), uncontrolled water additions, feed-rate upsets, changes in crusher performance, and mechanical upsets such as blockages in pumps and classifiers. Many of these disturbances occur with a frequency which is too high for an operator to detect and react to efficiently. Disturbances which occur on a time scale of several minutes up to several hours can be effectively dealt with using automatic control.

Jan 1, 1979

By A. Mehmet, W. A. M. te Riele

A pilot-plant investigation in a NIMCIX contactor has shown that activated carbon can extract more than 93% of the gold in return-dam solutions. The average gold concentration in the barren solution was less than 0.003 mg/L from a feed averaging 0.048 mg/L. The carbon was eluted by the Zadra procedure. The operating conditions of the elution-electrowinning circuit are reported, and the elution of the gold and other metals is discussed. The reactivation of the carbon by use of the Rintoul kiln is described, together with the results of reactivation. The consumption of reagents in the process cycle is presented in sufficient detail to allow the economic viability of this technique to he evaluated for the recovery of gold from low-grade solutions.

Jan 1, 1990

By Winfield G. Wright, Philip L. Verplanck, Philip L. Hageman, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

Geological, hydrological, and geochemical information synthesized in a Geographical Information System (GIS) for water and rock surrounding South and Middle Forks of Mineral Creek, northwest of Silverton Colorado, was analyzed to distinguish between the natural and the mining-related sources of metals to dace waters in the watershed An important natural source of metals to surface water emanates from a porphyry molybdenum deposit south and upslope from the Middle Fork of Mineral Creek. Interaction of surface and ground water with fractured, altered rocks and permeable, Quatemay-age surficial deposits produces downstream water quality that does not meet current State of Colorado water quality standards for metals and pH. GIS site characterization and three-dimensional modeling distinguish surficial deposits as volumetrically substantial, significant sources of naturally occurring metals that strongly influence water quality and complicate ongoing mine-site mitigation efforts. Our findings indicate that regional hydrologic and geologic information needs to be evaluated before realistic water quality guidelines are established and mitigation recommendations are confidently implemented.

Jan 1, 2000

By K. Getsos

Western Greece is a favorable site for exploration and discovery of oil fields. The most important potential source rocks seem to be all the rocks deposited before middle Jurassic under special circumstances, such as reducing conditions, which allowed preservation and maturation of the organic material. In general all the rocks of middle Jurassic to Paleogene are not favorite source rocks. The porosity type was studied on fifty samples using scanning electron microscopy (SEM). Potential reservoir rocks are the porous Paleogene wackestones-packstones with boring, channel and vuggy porosity type. Finally seal rocks are the impermeable mud-stones and wackestones of Jurassic, Cretaceous and Paleogene age. These rocks consist of micrite and whole sells of foraminiferas and the porosity type is mainly intercrystal/interparticle. A Total Organic Carbon (TOC) analysis, conducted on seventy samples using a wet oxidation method, has revealed an extremely low TOC content (less than 0.05 %). This amount is by far less than the minimum organic content amount, required for source rock characterization and characterizes all the rocks of middle Jurassic to Paleogene age. Additionally, 18O and 13C stable isotope analysis was contacted and the results are given in d values. All the rocks within the studied time interval have much lower d values than petroleum source rocks. Clay mineral content was studied in almost seventy samples. As is indicated by the clay mineral content the studied rocks have reached up to the Middle Diagenesis and the temperature during diagenesis was rather low.

Jan 1, 2006

By G. Gaidajis

For the environmentally safe management of the sulphidic waste rock produced from the Stratoni mining facilities, TVX Hellas has examined, within the frame of the funded European research program ROLCOSMOS, the effectiveness of an alternative rehabilitation scheme involving the segregation of the sulphide rich components of waste rock and the engineered application of alkaline additives. The examined waste rock management scheme was evaluated with laboratory test work followed by pilot-scale field applications. In this paper, the results from the two-year monitoring period of the pilot scale application are presented.

Jan 1, 2002

[Costs may be classified according to their source and behavior: Scale of aggregation - Total costs - Unit costs Time period for which the costs are charged - Product costs - Period costs Controllability and relevance for decision-making and control - Controllable costs - Noncontrollable costs - Sunkcosts - Opportunity costs Their basic source - Production costs (also termed manufacturing costs) - Nonproduction costs How the costs change with changes in activity - Fixed costs - Variable costs - Semivariable costs Traceability to individual units of production - Direct costs - Indirect costs Use in planning (budgeting) and subsequent control - Standard costs - Normal costs ]

Jan 1, 1999

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

6.1 INTRODUCTION A surface structure will suffer damage when the additional stresses induced by ground deformations associated with surface subsidence, plus the original stress introduced by construction de¬sign, exceed the strength of the structural elements. In this con¬text, there are two methods available for preventing and control¬ling surface structural damage: one is to strengthen the structure and the other is to design the mining operations such that ground deformations at the structure site can be reduced to an acceptable level. Mining operations include panel layout and mining tech¬niques. These methods are detailed in this chapter. It must be noted that most prevention/control methods men¬tioned in this chapter are used in the countries where the reference papers are cited. In the United States, the coal operators are not required to take those measures mentioned in this chapter. Some of the methods described in this chapter cannot be implemented with¬out changes in the current mining practice as permitted by laws. In addition cost of implementing those methods are not considered here. 6.2 PANEL LAYOUT As shown in Figs. 2.9, 2.10, and 2.11, permanent ground deformations in a subsidence basin mainly concentrate near the edges of the underground opening, and can be divided into four zones. A structure located in different zones will be subjected to different types and magnitudes of ground deformations. In laying out the panels, Table 5.1 and Figs. 2.9, 2.10, and 2.11 could be taken into consideration. Attempts could be made to avoid placing the structure on a location where the ground deformation to which that structure is sensitive is at its maximum. Therefore rational design of the panel is the simplest way to reduce structural defor¬mations. Panel design involves the determination of panel dimension, panel edge location, direction of face advance, and use of yield chain pillars. A. Panel Dimension Since longwalls in the US employ a multiple-entry system, where rows of chain pillars are left unmined, subsidence over those chain pillars is usually smaller. Therefore, whenever possi¬ble, the panel dimension could be designed such that a major structure or structures are over those unmined chain pillars, be¬tween adjacent panels, or some distance beyond both ends of the panels. At the center of the supercritical final subsidence basin, a structure will not be subjected to any final or permanent ground deformations. In order to create such a condition, the panel width must be such that the structure will be located beyond the major influence zone of the final subsidence basin, the minimum dimen¬sion of which must be: [ ] where L is the width or length of the final mined out gob, t is the width or length of the structure to be protected, h is mining depth and [ ] s is the angle of full subsidence. B. Panel Edge Location Wherever there is a permanent panel edge, there are large ground deformations induced on the surface on both sides of the permanent panel edge. Therefore whenever possible the panel di¬mension should be designed such that the permanent panel edges could be located in the areas with the least impacts. In terms of permanent edge location, it is best to eliminate any permanent panel edge under a structure or groups of structures. If this cannot be done, the panel should be lengthened to reduce the number of permanent panel edges, or narrower multiple panels advancing in the same direction in a staggered manner could be employed. If the structures are located in Zones II and III, the longer dimension of the structure must be parallel to the nearest perma¬nent edge (Fig. 6.1). But in Zone IV, the longer dimension should be tangential to the corner of the permanent panel edge. If the structure is inclined to the permanent panel edge, it will be sub¬jected to twisting and shearing. C. Direction of Face Advance The direction of face advance should be parallel to the long axis of the structure. But if the structure is to be located at or close to the center of the final subsidence basin, the direction of face advance should be perpendicular to the long axis of the structure. Careful choice of the direction of multiple face advance is the most effective way to reduce structural deformation and thus dam¬age. This applies the principle of overlapping and cancellations of ground deformations, due to multiple face advance, at the right time and at the right intensity, e.g., opposing tilts, concave and convex curvatures, tensile and compressive strains are induced simultaneously on the structure to be protected by two or more faces. D. Use of Yield Chain Pillars In US longwall panels there are generally two or three rows of stiff chain pillars between the panels. The combined width of the chain pillars ranges from 100 to 350 ft(30 to 107m). depending on mining depth. In general, surface movement above the chain pil¬lars after the panels on both sides have been extracted is much smaller, as compared to that in panel center. Thus in order to create critical or supercritical width of opening and eliminate sur¬face bumps over the chain pillars, yield chain pillars may be em¬ployed (Jarosz and Karmis, 1986). However if yield pillars are to be used, it must be designed such that it yields totally right after the panels on both sides have been extracted. Unfortunately cur¬rent yield pillar design techniques cannot predict when and how much it will yield. In summary, whenever possible attempts could be made to lay out the panel in such a way that surface structures are located above chain pillars between panels or above solid coal beyond both ends of the panels. In those areas the surface structures will most likely be unaffected, or if affected, the damage is so minor that no remedial measures are necessary. 6.3 CONTROLLED MINING TECHNIQUES Several mining techniques are available for reducing the sur¬face ground deformations of specific types. Regardless of tech-

Jan 1, 1992

By E. D. Attanasi

The US mining industry finished the traumatic 1980s with a strong economic performance. Worldwide economic growth and capital spending led to tight metal markets. So, 1989 metals prices were generally higher than average 1988 prices. Financial markets' volatility resulted from US junk bond defaults, heavy US savings and loan losses and effects on the US budget deficit, higher energy prices, and the seemingly intractable problems of some debtor countries. Moreover, the events in Eastern Europe promise fundamental changes in the world economic system for the 1990s. US mining companies that survived the decade had weathered economic changes that, at one point, reduced industry employment by 40%, drove oil companies to divest or liquidate recently acquired mineral subsidiaries, and led to substantial write-offs of reserves. Canadian and other international minerals firms experienced similar industry upheavels. The forced modernization and capacity rationalization produced an internationally competitive US industry. For example, even though 1989 US copper production was 27% greater than in 1980, industry employment was less than half the 1980 level. The steel industry and other minerals industries showed similar productivity improvements.

Jan 1, 1990

By A. S. Ericson, J. H. Corrigan, E. J. Jahnsen

Calcine is transported from the Reduction Plant at 850°C in insulated hopper cars and charged into three rectangular electric melting furnaces each equipped with three - 18.5 MVA transformers. The electrical energy is applied through six in line prebaked carbon electrodes, and slag and metal are tapped at opposite ends of the furnaces on an intermittent basis. The slag, 5000 tonnes per day, is disposed of by a pot train directly to the dump. The ferronickel, 250 tonnes per day, is tapped into 40 tonne capacity ladles in which it is refined in two ASEA-SKF ladle furnace stations. Casting is done over lip at 1520°C in a pig casting machine with stepless speed control at up to 55 tonnes per hour. The ingots are stacked into self palletizing bundles weighing about 1500 kilograms and are strapped and tagged and transported to the seaport, from which the final shipment is made to the world market. The paper describes constructional details and gives information of both normal operation and start-up and shut-down procedures. Consumption figures for refractory, electrodes, electric energy and refining additions are given and metal chemistry is given before and after refining.

Jan 1, 1979

By K. Hanumantha Rao, K. S. E. Forssberg, A. Vidyadhar

Using pure albite and quartz minerals, the separation of albite from quartz using mixed cationic/anionic reagent schemes is assessed through Hallimond flotation, zeta potential and diffuse reflectance FTIR studies. The reagent schemes are tested in bench-scale flotation for the separation of albite from Greek Stefania feldspar ore. The single mineral flotation tests showed the feasibility of selective albite flotation from quartz at around pH 2 using a mixture of cationic diamine and anionic sulfonate collectors or a combined cationic-anionic collector of diamine-dioleate. In contrast to the selective flotation response of albite at pH 2, where albite is slightly negatively charged and quartz possess zero charge, the zeta potential and FTIR studies elucidate similar adsorption behavior of mixed collectors on both of the minerals. The infrared spectra not only showed the co-adsorption of anionic sulfonate or oleate with diamine on the surface but also showed that the diamine adsorption increases with the presence of anionic collector. The intrusion of anionic collector in between adjacent surface alkyl ammonium ions decreases electrostatic head-head repulsion, thereby increasing the diamine adsorption by increasing the hydrophobic tail-tail bonds. The discrepancy in the flotation and adsorption results at pH 2 is attributed to the coarse and fine size particles employed in these studies, respectively. The comparable adsorption on fine particles of albite and quartz at pH 2 is explained by the interaction of ammonium ions on silanol groups by hydrogen bonding besides electrostatic interactions. The bench-scale flotation results indeed showed that selective albite flotation takes place only after desliming the feed material. An albite concentrate exceeding 10% (by weight) Na20 is produced from a material containing about 6.5% (by weight) Na20, where an albite product of more than 9% (by weight) Na20 is considered to be valuable. Key words: Flotation, Adsorption, Zeta-potential, FTIR

Jan 1, 2003

By Penglu Gan, Jinjie Zou, Chenglang Pan, Xiaowu Tang, Yu Zhao

"The north segment of the Zizhi Tunnel that consists of twin tunnels was excavated at a shallow depth in soft ground using the Shallow Tunneling Method. Based on continuous field measurements, the development histories of surface settlement were analyzed first. The observed development process could be roughly divided into three stages and the influence of river was evidenced. Transverse and longitudinal surface settlements above the twin tunnels were then fitted with empirical models. The obtained trough width parameters in transverse and longitudinal direction (it and il) and the volume loss (VLs) were presented and discussed. Additionally, surface settlement was compared with the crown settlement. The relationship between surface and crown settlement behaved in two different ways inside and outside the river-affected region. The findings in this project give references for predicting surface settlements in similar tunneling condition. INTRODUCTION Nowadays tunnel construction has become a major way of utilizing underground space in many large cities. The ground deformation will be inevitably induced in the tunneling process. Engineers should always be careful about excessive deformation that may damage adjacent structures. For shallow tunnels, controlling ground deformation turns to be more risky. Since soil arching is not completely formed in the shallow tunneling, settlements can easily develop from tunnel crown to ground surface.A conventional tunneling method named Shallow Tunneling Method (STM) has been developed and widely applied to constructed shallow tunnels in China. The major difference between this method and the New Austrian Tunneling Method (NATM) is whether considering self-supporting capacity of surrounding ground or not. In order to reduce the disturbance of surrounding soils, several guidelines are highlighted in this method, including advanced pipe forepoles, strict grouting, short excavation length, strong support, quick closure and frequent measurements (Fang 2012). Nevertheless, the ground deformation is still hard to control and becomes a concerned problem, mainly because ground settlement has some regional features and largely depends on the detailed excavation methods (bench cut method, multiple heading method, etc.) and ground condition (sand, clay, decomposed rock, etc.)."

Jan 1, 2016

By J. Bigu

Use has been made of several theoretical models to predict radiation levels in underground uranium mines. The models used are the Evans model, the Thomas-Epps mine model, the isolated mine model, the mine tunnel with no air flow and the mine tunnel with air flow (Beckman and Holub). Calculations based on the above models have been extended to include thoron gas and its progeny, a common occurrence in some Canadian uranium mines. Theoretical predictions include radon and thoron progenies WLs and concentrations, and some ratios of great practical interest. The main differences between the models are pointed out and comparison is made with experimental data gathered during the last three years in several Canadian underground uranium mines.

Jan 1, 1981

By G. Bhaskar Raju, S. Prabhakar

The amenability of column flotation for the beneficiation of fluorspar was investigated, and the overall performance of the column, flotation was compared to the performance of the existing conventional flotation cells at the plant. It was estab¬lished that improved grades and recoveries could be obtained by adopting column technology. Acidspar concentrates as¬saying 97% CaF2, suitable for HF manufacturing, can be produced by adopting two-stage column cleaning in place of multistage cleaning by conventional cells. Similarly, metspar concentrates assaying 90% CaF2, suitable for metallurgical applications, can be achieved in a single-stage cleaning by column flotation. This is an improvement over what is now being achieved using the existing conventional rougher and three-stage cleaning cells in the plant. The number of stages, i.e.,four in the acidspar circuit and four in the metspar circuit, including rougher stages, can be eliminated by adopting a three-column configuration. Thus, the cost of production, the complexity of the circuit and the power consumption can be effectively reduced with other attendant benefits.

Jan 1, 2000

By Frank P. Traczyk

INTRODUCTION The process of solid-liquid separation can be an important decision in plant design. It is very important that one must consider not only the most effective means of solids-liquid separation, but also to consider the effects on upstream and downstream processes. A solid-liquid separation is done either to remove the solids £ran the liquids as in copper concentrates or rave a liquid from the solids as in uranium operations. In either case, washing can be an important consideration to clean the solids or recover the liquids. This section will deal with solid- liquid separation other than thermal, sedimntation processes, or hydro cyclones. The three major areas discussed are pressure filters, vacuum filters, and centrifuges that are most cannon in the minerals industry. PRESSURE FILTERS Pressure filters are one common type of solid-liquid dewatering devices. There are my different types of pressure filters that are both continuous and batch operations. They are characterized by using an external pressure to push or force the slurry through porous media to force the liquids out of the solids. Whereas vacuum filters are limited to one amsphere or bar working pressure, some types of pressure filters operate as high as 16 bars pressure. Pressure filters are also effective for hot slurries where a high boiling point can be a problem or precipitation occurs under vacuum. The types of pressure filters most common in the mineral processing industry include plate and frame and recessed plate filters. Some of the new technologies including automatic pres- sure filters and belt presses are also discussed. Plate Frame Filters Plate and frame filters are one of the oldest and most effective means of both dewatering solids and clarifying liquids. Plate and frame filters consist of a skeleton that is used to hang or support alternate plates and frames that are pressed together to form chambers. The filter plates consist of a drainage grid that is covered by sane type of filter media through which a liquid is

Jan 1, 1986

By E. Kaya

Investigations of fine grinding of bituminous coal in a laboratory-scale pulverizer are described. The results indicate essentially "normal" breakage behavior at relatively coarse sizes (greater than about 20 µm) but show clear evidence for re-agglomeration in the fine size range (less than about 10 µm). A simplified population balance model for simultaneous growth and breakage has been formulated. Breakage rates and breakage distributions are assumed to follow the patterns typically observed in simple grinding systems. It is recognized, however, that solid particles and agglomerates may exhibit different breakage behavior. Agglomeration rates are assumed to be determined by contact probability, i.e. by the relative numbers of interacting particles. Based on comparisons of model simulations and experimental data, it appears that agglomerate re-breakage rates and fragment size distributions are quite different from those for solid particles. The result is that product size passes through a minimum and then increases with time as agglomeration begins to dominate.

Jan 1, 1996