Search Documents

By T. E. Bernard

"Refuge alternatives (RA) provide shelter to miners trapped underground during a disaster. RA manufacturers must demonstrate that their RAs meet the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and the management of heat that results from the RA occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements, and carbon dioxide generation that is representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current US coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in an RA. The highest likely metabolic heat generation ranged from 115 W to 135 W, depending on RA occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 LO2/h/person (0.81 ft3/h/person) and 20 LCO2/h/person (0.71 ft3/h/person), which means the margin of safety is 50% or more when compared to the MSHA requirements. INTRODUCTION Refuge alternatives (RAs) provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their RAs meet Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen, the removal of carbon dioxide, and the management of heat that results from the occupants and the mechanical/chemical systems in the RA [1]. These MSHA requirements were based on a standard 70 kg (168 lb) male with an assumed allocation of activity of 80% rest and 20% moderate activity level [2]. The purpose of this paper is to re-examine the metabolic heat generation and oxygen and carbon dioxide requirements of miners in an RA based on actual miner size and more realistic RA activity levels based on current RA designs. The purpose of this paper is to re-examine the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and heat generation. To achieve this, researchers took the following steps to estimate the metabolic demands and the associated heat generation, oxygen requirements, and carbon dioxide production. 1. Characterized the anthropometric characteristics of the miner population. 2. Described the metabolic rate profile of RA occupants. 3. Characterized the maintenance demands of RAs. 4. Summarized oxygen supply and carbon dioxide removal volumes. ANTHROPOMETRIC CHARACTERISTICS OF MINERS The weight, height, and age distributions of the adult male populations are summarized in Table 1. For each data set, the reported mean and standard deviation are provided. The 95th percentile (%ile) value for height and weight for each population was the mean plus 1.64 times the standard deviation."

Jan 1, 2017

By Kot F. v. Unrug

In spite of extensive research and accumulated experience from mining operations, appropriate coal strength values for pillar design remain debatable. Coal strengths determined in the laboratory on standardized samples vary widely among various coal seams with poor repeatability. Penetrometric in situ strength testing obtains multiple measurements at multiple horizons within the coal seam to provide a strength profile. Alliance Coal has used that method in many of its mines for pillar design. Pillars in these mines perform well. This paper presents a series of case studies and discussion of issues related to coal pillar design. The analysis demonstrates that the proposed default in situ strength of 900 psi is appropriate when no other data exist. However, in the case of appropriate strength measurements combined with analysis of pillar structural composition, differing values can be used successfully. In areas where the penetrometric derived in situ strength is greater than the standard 900 psi in situ strength, reserve recovery has been optimized as required by law without compromising safety.

Jan 1, 2009

By Thomas P. Meloy

The understanding, quantification and use of locked particles. Specifically discussed is the use of Textural Transforms (Meloy, 1991) for the implementation of the Interfacial Area Conservation hypothesis (Meloy, 1984); the quantification of the locked particles as a function of fragment to inclusion size ratio; and the selection of set points.

Jan 1, 1991

By E. J. Beckman, R. M. Enick, C. Shi

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. Two inexpensive and environmentally benign fluids were selected for the study, water and carbon dioxide. The separation, which is conducted at 295 K and at the vapor pressure of carbon dioxide (6.0 MPa), is based on differences in wettability between the precious metals and other minerals. Contact-angle results indicated that, in the presence of water and liquid CO2, gold is slightly hydrophobic. The addition of CO2-soluble fluoroalkyl thiols or f uoroetherthiols increased the hydrophobicity of gold exposed to water and CO2 to a greater extent than alkylthiols. Minerals, including quartz, pyrite and magnetite, were hydrophilic. During the separation, an aqueous slurry of fine mineral and gold particles was mixed with liquid carbon dioxide. Pure gold particles (-325 mesh) were found to agglomerate at the H2O-CO2 interface. The minerals tended to remain in the aqueous phase. Despite these promising preliminary results, very poor gold recoveries were obtained when applying the procedure to an Australian gravity concentrate. This was attributed to the native gold particles in the concentrate being either too large, agglomerated in slimes or coated with minerals. Although this particular application was unsuccessful, this water-CO2 biphase technique may be applicable for other separations that require the removal of very fine, hydrophobic particles from an aqueous slurry.

Jan 1, 2000

By Debra W. Struhsacker, Jean Kiel, Jeffrey Thatcher

3.1 INTRODUCTION As heap leach precious metal projects become increasingly common in the United States, federal, state and local regulatory agencies are beginning to take a closer look at the short- and long-term environmental consequences of this recovery technology. From an operator's point of view, there is seemingly a confusing regulatory maze to be navigated and a plethora of permits and approvals to be obtained prior to commissioning a heap leach operation. The degree of difficulty associated with obtaining permits for a heap leach project depends largely upon the state in which the project is located. Permit acquisition is generally easiest in those states most familiar with heap leaching technology. For example, heap leaching is well understood in Nevada, and heap leach operations are relatively easy to permit, although permitting conditions in Nevada have recently become more stringent. However, many states are just beginning to become familiar with heap leach operations. Many of these states such as Idaho, Colorado, South Dakota, Oregon, Montana, Washington and South Carolina are in the process of drafting regulations and establishing guidelines for heap leach projects. In most cases, these regulations specify design and operating criteria as well as reclamation and decommissioning procedures. This chapter provides an overview of the regulatory and permitting aspects of heap leach operations. Permitting requirements for projects developed on federal land are discussed in detail. 'The state and local regulatory atmosphere and permitting requirements for various states are also presented. The chapter concludes with a generic permitting strategy. 3.2 KEY ENVIRONMENTAL CONCERNS The primary concern of most local, state, and federal regulatory agencies is the use, storage and transport of sodium cyanide (NaCn), and potential cyanide contamination of surface and groundwater resources. The toxicity of cyanide to people, fish and wildlife is also an important issue. Unfortunately, in the public eye, cyanide heap leaching has some emotional impacts similar to those associated with radioactivity and uranium mining. This perception and the general lack of understanding of cyanide can lead to unnecessary concern about cyanide contamination, further complicating the regulatory environment.

Jan 1, 1988

By John Carson

Belt feeders are commonly used to meter the flow of bulk solids from bins and hoppers. If the interface between the hopper outlet and belt feeder is not designed correctly, flow from the bin may be severely compromised, resulting in problems of no-flow, segregation, flooding, etc. By knowing the flow characteristics of the bulk solid being handled and applying proven design techniques, such problems can be avoided. Relevant bulk solids flow characteristics are identified, along with measurement techniques. Design procedures for correcting problems with existing feeders as well as proper design of new feeders are presented, along with case histories of successful application of these procedures.

Jan 1, 2008

By W. Haupt, M. Thormé, H. J. Ertle, K. Reim

Though Germany has a very old mining history, her experience in uranium mining only started in the late sixties. Today in the Federal Republic of Germany (FRG) there are only 5 small mines in the exploration stage, namely Menzenschwand and Müllenbach in the Black Forest and Mähring, Popenreuth and GroBschloppen in northern Bavaria. In all these exploration mines much development is required to define shape and size of ore bodies. Mining engineers, government authorities and environmentalists alike are very much concerned about environmental safeguards and protection of mine workers against radon and its daughter products. Miners are affected by internal and external radioactive exposure. In general the external [f3]- and [µ] -exposures can be considered as small in comparison to the internal exposure and are therefore not discussed in this paper. The internal exposure is caused by the inhalation of radon and its daughter products and is relevant to the lung as the critical organ. The nobelgas radon is inert and does not from compounds with other elements easily. Contrary to the physical half-life of 3,8 days the biological half-life of radon is only 10 to 20 minutes. During the rentention time in the body only approximately 1 % of the long-lived decay products are retained in the system (SCHOGER, 1976). In this connection is it important that the radon resorption as well as the radon secretion varies individually and depends to a large extent on the age of the person (SCHOGER, 1960). RENOUX et al. (1978) have determined that the greatest part of the a(-activity in the air is attached to aerosoles with a diameter of 0,4/14. The radiation exposure of the lung by radon is negligible if compared with the exposure by short-lived decay products. For this reason one has introduced the concept of the potential [o](-energy (P) of the short-lived radon decay products, which means the total [ct]-energy, which is produced when an atom decays in the decay-series down to the long-lived lead-210. [ ] The unity of the potential [o]-energy concentration in the SI-system is 1 j/m3 air. In radiation protection however a specific unit is used namely the working level (WL): [ ] The WL-unit, though internationally recognised has not been introduced officially in Germany. Because of the large amount of tunneling still to be done in the FRG, the various mines departments responsible for safety and health in mining ask searching questions such as: - What are the laws governing radon emanation in tunneling? - Can workers be adeguately protected against radiation hazards? - How should one drive through high grade uranium ore? - What happens if the ventilation system breaks down?

Jan 1, 1981

By K. Y. Haramy, E. C. Westman

Anomalous geologic or stress conditions ahead of a longwall face have the potential of causing great harm to both the individual miner and the mining operation as a whole. NSA Engineering has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of afield effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration that was likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with the laboratory measurements.

Jan 1, 1997

By Stéphane Servant, Jacques Ouellet, Ferri Hassani

This paper presents essentially the logistic and practical aspects involved for in situ testing of mine paste backfill with a self-boring pressuremeter. The investigation discussed in this paper is part of an extensive and ongoing research project to identify and validate an in situ testing technique for cemented mine backfill such as hydraulic or paste backfill as well as Insitu behavior of backfilled stopes. After a literature review on field testing of soils and past experiments on mine backfill in situ testing, the self-boring pressuremeter was selected as the most appropriate instrument for this task. The authors presents in this paper the technical aspect involved in a field trials that was conducted in a Canadian underground mine using paste backfill. The results of this first successful trials show that self-boring pressuremeter test can provide high quality and reliable backfill characteristics results, using analytical techniques developed for soils (Ouellet et al., 1998). The parameters obtained were: estimation of the lateral stress in the ground, the soil stress-strain response and the soil strength. The logistic and equipment required to conduct such testing underground is fully described. Performance achieved in the field and technical difficulties encountered are highlighted. Recommendations for future experiments with such instruments are given. Some potential technical improvements to better adapt this in situ testing technique to mine backfill are proposed.

Jan 1, 2001

By Henry H. Roos

NTRODUCTION In the mining industry, a "drill jumbo" is a drilling unit equipped with one or more rock drills and mounted on a mechanical conveyance. Jumbos range from single¬drill ring drills mounted on simple steel skids to sophisti¬cated multiple-drill units mounted on diesel engine powered carriers and equipped with automatic controls and sound-abatement cabs. Individual types of jumbos usually are designed for specific tasks such as fan drilling in sublevel caving operations. Some units, such as development jumbos, can be utilized for several functions in addition to their normal applications, e.g., for production drilling in room-and-pillar operations, stoping in cut-and-fill mining, etc. Mine operators can purchase individual components from manufacturers, assembling these components into a jumbo suitable for specific conditions. However, this requires that mine personnel have good engineering and mechanical abilities. Although manufacturers of jumbos maintain facilities for designing machines to meet con¬ditions created by new mining methods and unusual ap¬plications, the cost of the engineering and experimental work for new types of jumbos should be evaluated in terms of both costs and benefits; it may be advantageous to plan the mining operation so that existing and proven units can be utilized. GENERAL SELECTION CRITERIA Since the operating conditions vary in underground mines, the design of a jumbo must be selected to cope with the individual characteristics of the mine. The necessary considerations include access space into the working areas, grades expected to be encountered, radii of the curves, ambient temperatures, the characteristics of the rock, the acidity or alkalinity (pH rating) of the mine water, etc. Access to Mine Workings The mine workings must be accessible to the selected jumbo. Frequently, a jumbo must be disassembled at least partially to pass through the mine shafts. There¬fore, a bolted construction allowing disassembly into pieces of suitable size and weight is desirable in most applications. Type of Undercarriage Generally, a crawler-type undercarriage should not be used in trackless mines having acidic mine water. The acidic water causes an electrolytic action between the individual crawler parts and causes rapid corrosion and early failures. Propulsion A two-wheel drive on a pneumatic-tired jumbo is marginal for grades exceeding 12%. A four-wheel drive unit with good weight distribution is capable of operat¬ing on grades of up to 35%. At least 30% of the gross vehicle weight (GVW) should be carried on the steering axle; otherwise, the steering tires may not have sufficient traction on loose road surfaces and may "plow" instead of steer. To assure stable operation in mines with steep grades, the height of the center of gravity of the jumbo should be considered. It should not make the unit prone to rolling over on the steep grades that may be encoun¬tered. Turning Ability In confined working areas, a skid-steering or crawler unit has the best maneuverability. An articulated carrier is preferable when base-rotated parallel booms are being utilized. A rigid-frame jumbo with automotive steering is compact and economical, having lower maintenance requirements than the other two types. However, the turning radius of a rigid-frame unit is wider than either the skid-steering or articulated units, and this wider turning radius may be detrimental in mines with narrow drifts. JUMBO COMPONENTS Rail Undercarriages A mine with a rail-transportation system generally utilizes drill jumbos that are mounted on rail-type under¬carriages. With a light load and good weight distribu¬tion, this carrier may consist of a simple two-axle four-wheel platform onto which the boom-mounting brackets are attached. As the depth of the round and the penetration rates increase, the weight of the equip¬ment installed on the chassis also increases. The greatest problem with a heavy overhung load is balancing the carrier; a three-boom unit may require a substantial amount of counterweighting to maintain an acceptable 70% to 30% axle-load balance. Although lengthening the wheelbase helps balance the unit, a long wheelbase increases the turning radius, often creating problems on curves and sometimes requiring a swivel truck-type chassis. A good rule of thumb for a simple four-wheel undercarriage is to maintain a wheelbase length to track gage-width ratio that does not exceed 2.5 to 1.0. For a larger ratio, a swivel truck should be utilized. Swing-out outriggers or roof jacks help keep a jumbo in place during the drilling cycle. Usually, a rail-mounted jumbo is not self-propelled. Instead, it is maneuvered into place by a locomotive. Occasionally, several headings are being advanced in close proximity, and a self-propelled jumbo is con¬venient. In electrified mines, such a jumbo utilizes conventional battery-powered traction gear; in dieselized mines, hydrostatic drive components offer good flexi¬bility. The tractive power requirements of a typical rail jumbo may be calculated from the formula: HP = [(RR + GR) X Sl/[33,000 X Em X Eh]

Jan 1, 1982

By R. F. McFarlin, H. E. El-Shall

Since its inception, the Institute of Phosphate Research has examined every promising proposal in order to find an economical, practical and environmentally sound method of dewatering phosphatic clays. The in-house development of the FIPR/DIPR process (DIPR = Dewatering Instantaneously with Pulp Recycle) would appear to answer that quest. When small amounts of fibrous materials are mixed with clay slurries and flocculent, rapid dewatering occurs. Clay solids contents of 20 to 25% can be attained by simply rolling the clay mass down an inclined screen. Higher solids (>40%) are reached by physically pressing the cake; e.g., with a belt press. Because mechanical pressing devices are too expensive for phosphatic clay treatment, FIPR has developed the "sandwich" method of simultaneously dewatering the phosphatic clays and reclaiming the mine cut, as well as a second alternate, the "median strip" proposal. Economic projections of these bench-scale alternates suggest that the FIPR/DIPR process should be no more costly than present practice, when credit is given for the simultaneous reclamation accomplished.

Jan 1, 1993

By D. C. Torre

The need for a successful, efficient and reliable continuous face- haulage .system for use with continuous mining machines has been apparent since the first continuous miners were introduced some twenty-five years ago. Some thought and effort were given to the development of continuous haulage over the last twenty years or so. Some initial success was experienced in this area by The Long Company with a system involving bridge conveyors, as far back as the late 1950's. However, extensive success with continuous face haulage for use behind modern, high product¬ion, continuous miners escaped the industry until the early 1970's. It is true that continuous face haulage was successfully introduced into low seam mining, generally in seams ranging under 1.07 m (42") in height, in the 1960's, for use with relatively low production, low seam, auger type continuous miners. However, those available systems which have achieved success in the lower seams, where relatively low capacities are adequate, are not directly applicable for use with today's medium and high seam miners with their standard production capacity of 9.1 - 10.9 mtpm (10 - 12 tpm). Since the late 1960's and early 1970's, several machinery manufacturers, and at least two major coal companies, have devoted considerable expense, time and effort to developing truly successful continuous face haulage for use in coal seams ranging upward from 1.2 m (4') in height. Continuous face haulage equipment has been developed in the last five years employing a variety of transportation media and design concepts, including some which have received wide publicity such as those employing hydraulics, and pleated belt. The truth of the matter is, however, that the only universally applicable and widely successful continuous face haulage equipment introduced to date has been that employing a combination of bridge conveyors and mobile, self-propelled, bridge carriers, connected at the inby end to the tail of the high production continuous miner, and at the outby end attached directly to the panel conveyor (Fig. 1 & Fig. 2) or, on occasion, to a short, self-contained conveyor which, in turn, empties directly onto the panel conveyor. While these bridge type continuous haulage systems are available with both belt and chain conveyor components, the most widely applied and successful system in seams above 1.07 m (42") in height is that offered by The Long-Airdox Company. The standard unit for use with 9.1 - 10.9 mtpm (10 - 12 tpm) continuous miners is normally equipped with belt. However, they have built, and successfully applied, versions of this system employing chain conveyors, (Fig. 3), mainly for operators having extremely difficult mining conditions, including excessive amounts of water

Jan 1, 1977

By B. (Manas) Das

Rock characterization for geotechnical purposes using the microhardness technique is discussed in this paper. The concept of rock characterization and its steps are logically developed. The geotechnical properties should be functionally tethered to the technological problems for characterization. The overriding geotechnical concern is rock mass stability. The important factors in this respect are rock properties, structural discontinuities, ground water, field stress, temperature and technological factors. The rock properties are the primary factors and the other factors generally affect rock properties. Of the rock properties the strength and elastic properties can form a basis for rock characterization. The microhardness technique can provide these two properties. Study on coal shows that the microhardness impressions can be used for this purpose. On the basis of this study coals of all ranks can be divided into distinct geotechnical groups. The details of these are discussed in this paper.

Jan 1, 1986

By M. Stefanakis, M. Errington, A. Kontopoulos, J. M. Prevosteau, K. Adam

The Olympias arsenical pyrite concentrate assaying 25 g/t Au, 40% S, 40% Fe and 12% As is highly refractory in nature; an oxidation pretreatment step is required to liberate gold and render it amenable to cyanidation. In the present study mineralogical analysis techniques including Image Analysis, SEM, EPMA, SIMS, Mossbauer, ICP/MS, etc., have been employed in order to investigate the mode of gold occurrence within the Olympias pyrites. Bacterial oxidation was used as a case pretreatment route and bacterially leached products were examined under SEM. The mineralogical observations and the relevant metallurgical and cyanidation test data were combined to establish a correlation between the mineralogical characteristics of the raw and oxidised products and conditions prevailing over the oxidative pretreatment step and the gold liberation achieved.

Jan 1, 1990

By M. Charles Gilbert

Basement rocks in southern Oklahoma are divided into two groups. One group is the Lower Cambrian Wichita Igneous Province, a diverse igneous suite that crops out in the western Arbuckle Mountains and in the Wichita Mountains. These largely bimodal igneous rocks were emplaced in an intracratonic-rift environment. The other group, the older, is a set of Precambrian rocks of the Eastern Arbuckle Province, yielding ages between 1,350 and 1,400 Ma, exposed in the core of the eastern Arbuckle Mountains. These are deeply eroded mesozonal granitic rocks and associated granitic gneisses cut by numerous dikes ranging in composition from diabase to rhyolite. The southern Oklahoma igneous rocks have long been utilized mostly as dimension and crushed stone. Most of the early quarries were in granite of various red hues for monuments and facing stones. Large crushed-stone quarries are now exploiting both granite and rhyolite, which is used chiefly as aggregate and railroad ballast. The exposed basement rocks in Oklahoma represent an underdeveloped and accessible resource.

Jan 1, 1999

By A. Hayatdavoudi, E. Apande

Introduction Troublesome shales have plagued the petroleum industry for more than 50 years. Unstable boreholes have been experienced when drilled into shale formations; sane have been studied almost at the beginning of rotary drilling. A little progress has been made since then, but much is still to be learned. No simple solution exists so far, but good drilling practices combined with good mud practices have been helpful. It is well known that shales in general have a strong affinity for water, and when water is adsorbed, the stability of the shale section of a well is reduced; cohesive strength will be re- bed, properties will be altered and shale will generally expand and/or crumble. The amount of water a shale will adsorb depends on the characteristics of its clay mineral and the ionic concentration of surrounding fluid. Fluid loss and the resulting hydration of an unstable formation can lead to serious downhole problems. The rate of fluid loss depends greatly on the permeability of the deposited cake. In impermeable formations, however, there is no loss of fluid into the formation. As such, shale, because of its very low porosity and almost no permeability, could be termed impermeable. Yet there is strong evidence that shale surfaces are wetted by an invasion of fluid into the formation through microfractures and jointed planes. It is this wetting that causes the shales to swell and slough into the hole, resulting in problems such as increased mud volume and treating costs, bridges and fill-up, stuck pipe, overgauge hole, poor cement jobs and increased cement requirements, and logging and completion difficulties. Drilling operations have been defeated by severe shale problems, resulting in & hole being plugged and abandoned after several weeks of drilling. Shales are we1l known as being difficult and costly to drill. Numerous fishing jobs have plagued drilling operations, and the cost of reaming tight holes ad weighting up the drilling mud to control shale sloughing has been high. The concept of controlling water loss to stop sloughing was introduced in the 1920's. It was known-then that calcium in fresh water re- strains clay £ran excessive swelling (theory of osmosis) . This reinforced the belief that calcium-based muds such as lime, gypsum and calcium chloride should minimize hydration of clays. Lime muds were then introduced for this purpose and others in the 1930-1940 decade1. They were used for shale inhibition but were not effective. In an attempt to improve them, a special calcium-type mud beam popular during the 1950's. Hole enlargement continued and they too were considered ineffective. During & early 1960qs, papers were published claiming that shale swelling could be prevented by using high concentrations of chemical thinner called Chrane Lignosulfonate1. This began the era of highly treated lignosulfote muds. Unfortunately, the hole enlargement problem continued. During & mid-1960’s, oil based muds were used for the purpose of inhibition of shales. Not until 1966 did Mondshine2 suggest that the water phase be saturated with calcium chloride. The cost of using oil based mud was considered by most operators not worth the additional hole stability. The potassium chloride-polymer muds were also used in many fields in the United States and western Canada. The use of these muds has been claimed to prevent clay swelling by inhibition and encapsulation in sane areas of western Canada. They are also expensive and their ueneral application is still experimental. To reduce filtrate loss when sloughing shale becomes a problem during drilling is a reasonable practice. This study will investigate the use of cationic organic additives to mud to form a protective barrier between the shale - which are primarily composed of clays - and water that will keep water from entering the microfractures and will also prevent them from hydrating. In so doing, an understanding of modern clay chemistry and & dispersive properties of cationic additives in water based systems will be our most valuable tools. This study will also present and solve a mathematical model for simulating cation transport phenomena in fractured shales using the Framdlich equilibrium adsorption isotherm. The studies will analyze wellbore failure and stability as affected by cationic organic material.

Jan 1, 1986

By Richard Dunmore

Most coal seams in the United Kingdom contain firedamp, some of which is released into the ventilating airways as the strata around a working relax. The close sequence of seams in carboniferous strata is usually such that seams in adjacent roof and floor strata are also disturbed and potentially large quantities of firedamp can enter the workings from these sources. Since emission depends on the disturbance rate of the seams, higher coal production rates associated with increased mechanisation in the colliery accentuate the problem. Firedamp concentrations in UK underground workings are subject to statutory regulations1. To enable production to continue uninterrupted and in safety the problem is tackled by ventilation engineers by the provision of adequate ventilation in the airway and by the technique of firedamp drainage. In the UK the latter usually takes the form of cross-measure boreholes in roof strata, and increasingly also in floor strata, drilled from the gateroads, especially from return airways. In this way firedamp emitted from disturbed seams in adjacent strata can be extracted directly to the surface or to some safe position outbye, and the airways of the working district are not contaminated. Despite the use of firedamp drainage, considerable quantities of firedamp enter the ventilation air- stream and the concentration levels may be seen to be related to the coal production activites in the district. Figure 1 shows a typical recording of methane concentration obtained by a BM1 methanometer at a position outbye in a return gate where firedamp drainage was operating. The general rise in level throughout the working week may be seen, together with peaks occurring during production shifts and the gradual decay of emission over the weekend. In view of the fact that ventilation and firedamp drainage contribute a considerable proportion to the operating costs of the colliery, it is essential that the ventilation and firedamp drainage requirements be calculated as accurately as possible at the planning stage of the working. In the past the ventilation engineer has had to rely heavily on experience in neighbouring workings but with the development of mines in previously unworked areas there is clearly a need for a methodical approach to meet the requirements of planning. The work described in this paper represents such an approach and it is hoped that successful development and application of the method of prediction will lead to the widespread adoption of a routine procedure. The current development of a method of prediction of firedamp emission into longwall workings is based on the theoretical treatment of gas emission from coal seams proposed by Airey2 in 1971, which was based on his study of gas emission from broken coal 3 which was published in 1968. In common with other experimental methods of prediction, the method enables a calculation to be made of the total make of gas emitted from all sources of gas in the strata per tonne of mined coal.

Jan 1, 1980

By A. Bruce Waugh, W. W. Wen, Kevin N. Clark, Neville C. Lockhart, Bruce A. Firth

Australia is the world's largest coal exporter, and technological advancement is a key element of the coal industry strategy. The issues include: increased recovery of saleable coal; enhanced quality, i.e. lower ash, moisture, fines, phosphorus (sulphur is a relatively minor problem for Australian coals); better quality control; higher throughputs/lower costs; improved handling and transport; and reduced environmental impacts. In process terms, many coal preparation operations, particularly fine coal circuits, are relatively inefficient, and all circuits must also be matched and integrated for optimum overall operation. A holistic approach to technological improvement is desirable. This paper summarises research and development efforts, within CSIRO and its collaborators, across the unit operations as outlined in the title.

Jan 1, 1995

By Kevin DeSomber, Scott Bird

Larger grinding mills continue to utilize large gear-driven drives or electrical wraparound drives. The panel will include presenters from operations with large mechanical and electrical drives. JIM HANDLEY: Before we get to the third and final session, I want to introduce my co-conspirator for this session, John Mansanti. John is manager of milling with Newrnont Gold Company, Carlin, Nevada, and was very active in securing participation in this innovative symposium. I'm Jim Handley and I'm with Cyprus-Amax Minerals at the Sierrita copper and molybdenum mine. Our third presentation is titled "Geared Up or Wrapped Up?" I hear this topic discussed, but never at great length. I think that's because the opinions are fairly strong and diverse, and people generally aren't reinforced properly in their arguments. The first person to enlighten us on this topic is Scott Bird. He has more than 20 years with Kennecott, is a graduate in metallurgical engineering from the University of Utah, and is currently operations superintendent and deals with this phenomenon every day.

Jan 1, 1998

By L. J. Tucker

The magnetite orebody at Pea Ridge strikes NE-SH and dips at about 800 to the SE. The ore is high grade magnetite with a strike length of over 600-m and a maximum width of over 180-m on some of the levels. The shape and the mineral content of the iron orebody have been fairly consistent so far. The iron ore and surrounding basement rocks are Precambrian in age. These rocks are usually very competent, about 400-m of sediments lie over the ore.

Jan 1, 1991