Search Documents

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009

By Joe Keane

DOUG HALBE: The kickoff speaker, and my unanimous choice, is Joe Keane. Joe was born in Butte, Montana, and began his association with the mining industry as an under- ground miner at age 16. Currently he is president of KD Engineering and Metcon Research. He had it lucky when he went to school because there were only 44 elements in the periodic table, I understand. [laughter] Here's Joe. JOE KEANE: I'm doing this under protest. Maybe we can start the slides. Mr. Halbe gave me this topic, but I don't like it. I don't like Mr. Halbe either [laughter] because of the way he shanghaied me into this. He called me up on the phone and said this is what you're going to speak about: "Five Things I Never Want to See Again in Plant Design," and I said, "Huh!" Then I started getting stuff from SME about how to make a presentation. I have decided to change the title to "More Than Five Things I Never Want to See in Plant Design," since you can't have a completely negative speech; you have to have other topics. So we will have some other, not completely nonrelated, topics to sort of break the tension. I tried to find a joke to open with. I talked to Omar Mutati. All of his jokes were either about Bill Clinton, our beloved President, or they were too filthy to say in a mixed group. [laughter] So I decided to start this out with a profound statement. The pro- found statement is, "The meek shall inherit the earth, but not the mineral rights," [laughter] by J. Paul Getty. J. Paul Getty was one of my favorite guys because when a real obnoxious reporter asked him one day, "How can I become wealthy?" he said, "Drill for oil and find it."

Jan 1, 1998

By Daniel R. Stewart, Ralph R. Sacrison

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines, support definition and slope stability at the Climax mine, and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1992

By T. W. Lloyd

Accurately predicting coal seam discontinuities is an important part of modern underground coal mining. Conventional methods of coal exploration sometimes fail to identify rapid variations that may seriously impact mining and quality. Radio Imaging Method (RIM), a geophysical approach to mapping longwall panels, has been developed where electromagnetic signals are transmitted and received though the coal block. The amount of signal loss for a given distance, when compared to the coal seam characteristics, identifies anomalous areas. A comparison of RIM predictions with actual geologic conditions encountered during longwall mining demonstrates the accuracy and usefulness of the data.

Jan 1, 1986

By Y. Guan

The dissolution behavior of silver and copper from silver/copper alloys in ammoniacal solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of composition of alloys, concentration of lixiviants, stirring speed and temperature on the overall dissolution kinetics has been studied. Silver / copper alloys of three compositions were used in this study. The atomic percents of silver in these alloys were 76.9, 46.9 and 24.1. The results on the rate of dissolution obtained for these alloys have been compared with that of pure silver and copper under the same testing conditions. A particular emphasis has been given to the galvanic effect on the overall dissolution rates.

Jan 1, 1993

By J. M. Pachter

Property sales and acquisition are prominent features of today's coal industry. Before selling or buying a site, a company must know the property's economic net worth. Any evaluation of economic net worth would be inadequate if determinations of a property's environmental liabilities and costs were omitted. Short-term and long-term costs can result from liabilities related to reclamation, water treatment, subsidence, and hazardous waste disposal. A structured, interdisciplinary approach can aid in the delineation, summation, and scheduling of these costs and liabilities.

Jan 1, 1986

By James A. Barclay

Results of investigations over approximately the last 10 years by the Bureau of Mines and others on technology for recovering cell-grade alumina from domestic nonbauxitic resources such as clay, anorthosite, alunite, dawsonitic oil shale, coal ash, and coal shale are reviewed. It is concluded that, although many innovative techniques have evolved from this effort and have been shown to be technically feasible, energy and economic considerations will prevent any of the processes from competing with the Bayer process under normal conditions. Based on the Bureau's experience, some variation of clay-HCI leaching, HC1 gas sparging crystallization has the greatest potential as an alternative to the Bayer-bauxite process.

Jan 1, 1984

By B. T. Stanley

Traditional methods of creating a water tight shaft liner involve the use of segmented or welded steel. When shafts are located in ground that exhibits extremely difficult conditions of high water inflow and hydraulic pressure, composite liners are often combined with ground freezing during construction. The authors were searching for a cost effective and more flexible solution to hydrostatic liners design than the traditional concrete/steel composite design used so far. Searching through new technologies developed for tunneling applications, sprayed on membranes systems seemed very promising but were not developed for the specific circumstances encountered in shaft sinking applications where ground freezing is involved. Even though freezing is a very effective technique, it creates adverse temperature conditions for the application of spray on membranes. In addition, application and hydrating cure times for those membranes products ranged between six to twenty-four hours under ideal conditions (usually temperatures well above freezing point), which eliminated them from consideration in a shaft sinking cycle. While researching different spray on membrane materials, it was discovered that Stirling Lloyd Polychem Ltd. has developed and proven a different membrane material for waterproofing liners in different tunneling applications. The characteristics of the membrane exceeds the pressure parameters encountered in frozen shaft sinking operations, and the chemical cure times were reduced to one hour per layer which worked well into the shaft sinking cycle times. More over their system included a quality control procedure that allowed insuring integrity of the membrane at application time, a very desirable feature for shaft liner construction. However, the frozen rock surface still presented an unknown in the cure time and stability equation. As all membrane products a shotcrete substrate is usually required prior to application. The hypothesis used by the author was to use this shotcrete layer, not only as a substrate, but also as a thermal insulation against the frozen rock and the membrane during both application and curing time. The authors knew from experience that shotcrete could be applied successfully over frozen rock. But the shotcrete temperature curve over time was unknown and no information were found in the available literature. Testing was required to determine whether a suitable mix of shotcrete could be applied to the frozen shaft wall to provide enough heat of hydration for a suitable period of time to create conditions suitable for membrane application and curing.

Jan 1, 2012

By R. W. Bartlett

Computer deterministic models for predicting the time dependent extraction of copper by leaching fragmented rock (both in situ and heaped or piled) have been presented in the last two years by Bartlett1, Braun, Lewis and Wadsworth2 and Roman and Co-Workers.3 All of these models involve aqueous diffusion within the pores of the rocks from which the metal is being extracted. The rate of chemical dissolution of the ore mineral within the rock will also affect the kinetics in the case of sulfide copper ores and some of the more refractory oxide copper ores. Simulation is also needed for fine grain disseminated gold ores and low grade uranium ores that may be heap leached. The development of such leaching models has two major purposes: First, extraction estimates must be made for tong time periods particularly for situations where laboratory and field tests either cannot be made or where there is insufficient time for field testing. Second, the results of simulated leaching should indicate the relative importance of the extraction controlling parameters and, thereby, provide a better understanding of the complex leaching phenomena on heaped material being leached, and guide further experimental work.

Jan 1, 1974

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By G. Camposano, J. Aponte, B. A. Ferguson

The paper covers mining operations and preparation of the ore prior to metallurgical treatment in the Process Plant. Mining operations are primarily concerned with the delivery to Ore Preparation of a balanced ore feed within fairly rigid specifications as to both ore type and chemical analysis. The mining method, systems of geological and engineering control, and the equipment employed are therefore reviewed in this context. In Part One of the paper the physical and geological characteristics of the orebodies, including the varied nature of the ore itself, are first described. Orebody evaluation, the calculation and classification of ore reserves, mining planning and forecasting to ensure continuity of production are covered, and the particular problems presented by sampling, the erratic distribution of ore values and the variation in the density of the ores are also mentioned. Mine design and ore excavation practice are described, together with the way in which they have evolved with recent developments in modern mining equipment. In Part Two of the paper, a detailed description of the Ore Preparation plant is given, centred around the concept of rubbling as a means of separation of the barren hard boulders from soft lateritic ore. Ore blending and ore reclamation operations are explained followed by a detailed description of the drying and crushing plant. The importance of the control of moisture content and ore sizing in the feed to the metallurgical plant is emphasized.

Jan 1, 1979

By Vicki Seppala

Phelps Dodge Mining Company operates some of the world’s largest open pit mines. Safely mining in these deep pits requires the commitment to a proactive integrated slope management process. The slope management process also includes the continued look for improved slope design, construction, and maintenance of slope faces. This paper discusses integration of such technology as electronic programmable detonators, 3D imaging using ground-based LiDAR scans, and reflectorless slope monitoring systems in a slope management program.

Jan 1, 2005

By R. H. T. Garnett

Reserve estimation is a process that commences with sampling and culminates in the issuance of a reserve statement. The tin, gold and diamonds that occur as marine placers on the continental shelf are low grade with very erratic mineral distributions. Sampling, using a variety of special equipment, determines the extent and grade of the mineralization. The sample size is important, especially for diamonds. Together with the sampling density, it determines the accuracy of the grade estimate. Bulk sampling is a confirmatory process. The choice of mining equipment, either new or developed from onshore activities, dictates the unit costs, the cutoff grades and the selectivity of extraction. Thus, the size of the blocks that comprise the mining plan and the reserves are determined. A variety of estimation methods of different reliability are available, with the most sophisticated being kriging. Dilution and losses during mining must be taken into account in estimation, and a grade-volume curve should be constructed. Diamond deposit estimation also involves an extra variable, the dollar value of the stones. During and after mining, essential feedback on the accuracy of un estimation may be given by the RIE factor and by a mineral balance. Reserve estimates are required for several reasons and may be subject to public disclosure. The use of the correct definitions is, therefore, important.

Jan 1, 1999

By J. C. Hower

The Hardgrove grindability index (HGI) is a widely used coal-quality parameter with applications in coal mining, beneficiation, and utilization. An understanding of the petrology of the coal is fundamental to understanding the validity of the HGI in the given application. The HGI varies with coal rank, increasing (greater ease of grinding) with increasing rank through the high-volatile bituminous rank range; and the HGI varies with changes in the maceral and microlithotype composition, decreasing with an increase in liptinite and liptinite-rich microlithotypes. In this review, the .fundamental relationship between HGI and coal petrology, and consequently its relationship to coal utilization, is examined.

Jan 1, 1999

By R. A. Halatchev

Historically two basic approaches of production sequencing have been formed in the theory of open pit mine design. The first approach implements a technological discretization of the pit space within the ultimate pit outlines where the minimum working width is the limiting technological factor. The second approach uses a pseudo-economic discretization based on the implementation of analytical methods for designing intermediate/ultimate pit outlines and the concept of pit shells generation. The paper offers an elaborate analysis of both approaches used currently for discretization of the geological medium into working benches and modelling the working zone of open pit mine. The analysis is extended with a new vision for unification of the mining systems in open pit mine design under the form of a classification. A comparison of the approaches is provided to illustrate their advantages and disadvantages with regard to the implementation of the principle of waste deferment as one of the main principles of mine planning that exploits the time effect of money.

Jan 1, 2003

By G. Argyris

A number of important studies, ongoing environment monitoring efforts and mining and road construction projects in the lignite based electrical power production area of Amyntaio ? Ptolemais in North West Greece require an accurate and up to date model of the topography. In recognition of the importance of such a model, a project was initiated by the Laboratory of Mining Information Technology and GIS Applications in the Department of Geotechnology and Environmental Engineering of the Technological Educational Institute of Western Macedonia. A massive surface triangulation model was generated from vector data using an optimized Delaunay based method. Combined with aerial and satellite imagery, the triangulation model provides a complete 3D terrain model of the area characterized by high levels of accuracy, detail and realism. The generated model is easy to modify with new data in order to improve its detail and keep it up to date with ongoing earth moving and development operations in the area.

Jan 1, 2008

By V. K. Gupta

A detailed experimental study of the variations in grinding rate with particle size, particle load, ball diameter, ball load, mill diameter, and mill speed was carried out for a soft cement clinker and a hard cement clinker. The effects of the ball diameter, ball load and particle load were observed to be material (hardness) independent, and those of the particle size, mill diameter and mill speed to be material dependent. A sharp change in the grinding behavior was observed for both the clinkers at about 150 µm size. Below this critical size: (i) the hardness difference between the two clinkers became insignificant, (ii) variation in the grinding rate with particle size became markedly more pronounced, and (iii) mill speed had little or no effect on grinding rate. The importance of these results in the context of process optimization and control is discussed.

Jan 1, 1987

By P. R. G. Bak

The integration of interactive computer graphics technology with data analysis tools can assist in the evaluation of deposit models: the super- imposition of mine openings on complex geology can be quickly perceived using dynamic visualisation, colour-coding and transparency control while analysis functions assist in quantifying displayed information. To illustrate the functionality of such integration a research prototype system is presented which allows the interactive visualisation and evaluation of deposit models comprising both structural boundaries and the distribution of continuous properties.

Jan 1, 1992

By W. M. Husslage, M. E. Kock, T. Bakker, R. H. Heerema

Permeability in the blast furnace shaft is adversely affected by low-temperature reduction degradation of sinters. The fundamental cause of this is the expansion of the iron oxide phase resulting from the reduction of hematite to magnetite. The present study shows that expansion behavior during the hematite/magnetite reduction .step and the resulting microstructure are strongly influenced by the reduction temperature (partial oxygen pressure), the reducing agent and the nature of the hematite. The reduction rate is of minor importance. A reduction mechanism is proposed that can explain the dilation behavior and the magnetite microstructure. The results provide better insight into the reduction degradation behavior.

Jan 1, 2000

By C. Cigna, M. Patrucco, D. Savoca, E. Lovera

The paper deals with the activity program and the preliminary results of a research work commissioned by IReR Research Centre and Regione Lombardia to the Department of Land, Environment and Geotechnologies of Politecnico di Torino. The aim is to define measurement, analysis and control criteria for the emission of chemical and physical pollutants from non-metal mining industries, with particular reference to noise and airborne particulates. Such emissions are related to health risks and annoyance problems, both for the working crews and the neighbouring population, and so, in order to get an effective sustainability of the industry, suitable reduction methods and assessment tools are required. A simple technique for the evaluation and forecasting of both the emission levels and deriving impact has been tested at different mining and quarrying sites, considering their differences in terms of layout and exploitation method, the latter ascribed to a series of main typologies as present in Lombardia region.

Jan 1, 2005