Search Documents

By Richard L. Stein

INTRODUCTION Increasing a miner's chance of surviving a disaster requires advance planning for emergencies, adequate training of personnel, and the provision of proper survival equipment. It is extremely important that fires and toxic gases be detected early, and that warning systems such as stench, audible and visual alarms, and communications systems be provided to allow timely escape. However, situations do occur where timely warning is not provided and immediate escape is not possible, regardless of the precautions that are taken. Under such circumstances, a combination of new per¬sonal protective devices and old techniques can provide protection that is adequate to save a miner's life. SELF-RESCUE EQUIPMENT Self-rescuers are devices which provide a short-term supply of respirable air under the potentially lethal con¬ditions following a mine disaster. Functioning either as filtration devices for the elimination of carbon monoxide (CO) or as oxygen supplies, self-rescuers allow an endangered miner a limited amount of time in which to effect an escape or reach a place of temporary safety. Carbon-Monoxide Self-Rescuers For almost 50 years, filtration self-rescuers have protected miners' lives following explosions or fires. Designed to eliminate carbon monoxide from inhaled air, the first of these devices was approved in the 1920s and has evolved into the two units that are approved today-the Mine Safety Appliance (MSA) W-65 and the Draeger 810. Both of these units rely on the cata¬lytic conversion of very toxic carbon monoxide to rela¬tively safe levels of carbon dioxide (CO,). As shown in Figs. 1 and 2, both of these filtration self-rescuers operate in the same manner. On inhalation, the mine air passes through both coarse and fine filters that remove the dust, preventing the dust from coating the chemical beds or entering the miner's mouth. The air then passes over a drying agent that removes water vapor; this is required to prevent the water vapor from poisoning the catalyst. Subsequently, the dried air passes over the Hopcalite catalyst, where carbon monoxide is converted to carbon dioxide. Then, the air passes through a heat exchanger that reduces the temperature of the inhaled air. Finally, the air is inhaled by the user. Air exhaled by the user passes through the heat ex¬changer and exits the device through an expiratory valve. Both units of this type are subject to certain limita¬tions: 1) The units do not protect the user against oxygen¬deficient air; when air is inhaled through this type of self-rescuer, the device only removes the carbon mon¬oxide. If the mine air contains less than 15% oxygen, anoxia is inevitable. Symptoms of anoxia include dizzi¬ness, shortness of breath, quickened pulse, and deeper and more rapid respiration while the victim is at rest. During heavy exertion such as would be expected dur¬ ing escape efforts, a 15% oxygen level can cause loss of consciousness. 2) The units do not protect against excessive levels of carbon dioxide. Available data on carbon monoxide and carbon dioxide concentrations following explosions or fires are limited, but there are indications that the carbon monoxide concentration can rise to 2% and the carbon dioxide concentration can reach 5 or 6% of the mine air (by volume). In some situations, the in¬haled air could contain up to 6 or 7% carbon dioxide. At a carbon dioxide concentration higher than 2%, breathing patterns can be affected adversely. At a con¬centration of 6 or 7%, the effects include severe respira¬tory distress, with unconsciousness resulting from exer¬tion such as that needed for escape activities. 3) The units do not protect against high inhalation temperatures. The catalytic oxidation of carbon mon¬oxide to carbon dioxide is an exothermic reaction that evolves a large amount of heat. As the carbon monoxide concentration increases, the temperature of the inhaled air also increases. Available data show that above 1.5% carbon monoxide, the air inhaled through some self¬rescuers can be as high as 90°C (194°F). At those

Jan 1, 1982

By Harrison A. Schmitt

During .the past five decades or so we have passed from a time when it was difficult to point to a mine or an ore body and verify that it had been discovered by geological methods, through the. Twenties when the common saying was, "Who ever heard of a mine found by a geologist?", to recent decades when hundreds of mines and ore bodies are acknowledged geological discoveries and the above query can be ignored. Recently, however, the application of mining geology appears to have been downgraded, or so it seems to me. Basic geology in mining has been cheapened and glossed over in favor of geophysics and outcrop sampling, even though the latter is merely one technique of mining geology and, to some extent anyhow, has been used for a. long time. (Locke, 3, pp 81-87). Geophysics by itself and in conjunction with geology has had success in certain geological provinces, but limited attainment in mountainous terrane except in those few cases where strongly magnetic minerals are associated with ore. Nevertheless, in the Cordillera .many experimental techniques are offered as proved ones. This is not an intent to try to depreciate honest geo- physics. Continued experimentation and use of it is approved by all, but at the same time it is foolhardy to throw mining geology overboard, Generally both approaches should be considered and usually, at first anyhow, geology is the most direct one.

Jan 1, 1960

By Everett M. (Original by) White

Numerous articles have been written about the coal mine ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. How- ever, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers' Handbook, 1898, Caleb Pamely writes of an explosion that occurred at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio's, and in 1876 by Maryland's. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597 deaths. Because of this, the federal government took action and by 1910, the US Bureau of Mines had been established. This was perhaps the most significant change in health and safety for miners during the first half of the 20th century as the USBM concentrated its entire efforts in the study, research, and testing of methods totally directed towards improvement of the health and safety of the miner. After a mine disaster in Illinois, a federal law was passed in 1940 calling for federal coal mine inspectors. Then in 1969, Congress enacted the Federal Coal Mine Health and Safety Act following a mine explosion near Farmington, WV. In 1977, the law was revised and included noncoal mining operations.

Jan 1, 1981

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sandblasting agent, as a premium-grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. Staurolite is produced by E. I. duPont de Nemours and Company as a coproduct of titanium mineral production in Florida, where it was first recovered on a commercial scale in 1952 from the Pleistocene sand deposit known as Trail Ridge. At this deposit it comprises about one-fifth of the heavy mineral suite, the principal other heavy minerals being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and other nonconductive silicate heavy minerals are separated from the conductive titanium minerals on high-tension electrostatic separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total process, 200 t of raw sand yield 7 t of heavy mineral concentrate from which about 1 t of staurolite is recovered. The staurolite concentrates have the characteristics given in Table 1. Staurolite concentrates are sold in three grades having the size distribution of subrounded grains shown in Table 2. All three grades are used in sandblasting for cleaning metal, for paint removal, and for cleaning masonry buildings. Staurolite compares favorably with lower priced abrasives, such as boiler slags and silica sand, in applications where the abrasive is used only once and is not recovered and recycled. Because it is hard, fine, clean, and dense it can reduce blasting time, and less material is required to clean a specific area. Compared to higher priced abrasives such as aluminum oxide and garnet, which are recycled, staurolite costs significantly less per kilogram and cleans at equal or faster rates. Its breakdown factor, which is a measure of recycling performance, is intermediate between those for aluminum oxide and garnet. [ ] [Tables 3 and 4] show the blast cleaning performance of the three staurolite grades compared to other abrasives. [Table 5] compares the longevity of premium priced abrasives during recycling. [Table 6] shows a cost comparison between silica sand and staurolite. Fringe benefits claimed for staurolite's use as an abrasive are: 1. Good flow properties and freedom from the lumps or slivers found in silica sand or boiler slag abrasives. 2. Low dusting affords good visibility, permits faster working, and reduces cleanup problems. 3. Heated storage is not required during freezing conditions, because the mineral is nonhygroscopic.

Jan 1, 1994

By Michael J. Taylor

Introduction A prime goal in the design and operation of uranium milling waste or tailing disposal systems is to mitigate adverse effects of tailing liquid on the adjacent groundwater. Adverse effects are often defined as modifying the groundwater quality in such a manner as to have detrimental health effects on downstream users. To accomplish this goal, the following three types of systems are employed with regard to the seepage and groundwater aspects of waste disposal: Type I Systems Seepage is allowed to occur unabated from the tailing disposal facility. Detrimental radionuclides and chemical elements are prevented from causing adverse downstream effects by natural purification actions in the subgrade geologic materials and the near zone groundwater. Monitoring is required to assure the predicted natural purification is occurring. The consequences of seepage loss is minimal since the m be predicted with current investigation and analytical techniques and can be evaluated as to effectiveness during operations. Type II Systems Seepage is partially retained in a waste impoundment or leakage from a designed retention system is anticipated. Natural purification is relied on for controlling migration of detrimental radionuclides or chemical elements, or contingency planning is employed to collect and return the tailing liquid to the impoundment. Installation efforts and concern for escape of tailing liquid are greater than for Type I systems, but extra precautions to preclude all seepage are not implemented. Monitoring is required to detect leakage and/or assure the natural purification of escaping tailing fluid. The consequence for accidential excusions are moderate, and will be excessive only if massive system failure occurs. Type III Systems Seepage is totally restricted by a costly system constructed and operated with extra care. Natural

Jan 1, 1980

By John J. McCrone

In the Mining Industry, the means of handling and transferring lubricants has been given little attention over the years. An analysis of this process indicates that this neglect has often exacted a very high price. As the costs associated with labor, equipment utilization and waste disposal soar, the need for an efficient system takes on an increasing significance. Often the focus of bulk systems has been placed on the master container itself. Certainly, there is nothing new about a large lubricant container; they have been available over a period of years, known under a variety of names, "mini tank", "super drum", ?flo-bin" and "tote bin", to name but a few.

Jan 1, 1982

By Fred W. Shultz

In the past we have been somewhat harrassed by the terms "'quality control" and "process control". This is especially true where the industry is dependent upon the chemical analysis of their product which in turn informs them how, well they have been controlling the process. The information which they have received, in most cases, is of an historical nature rather than of current value. The word "control" is to have more significance in future operations. This is particularly true in the metals industry. As the industry continues to process lower grade ores, and processing costs continue to rise, they must obtain more information faster to exercise "control" to its fullest extent.

Jan 1, 1963

By Norman Weiss

The design of an ore-processing plant requires a high degree of cooperation among the geological, mining and metallurgical engineers. The purposes of this section are to provide mill design information most commonly needed by the mine planners and management, and to summarize the kinds of information that must be supplied to the mill designer to enable him to provide a suitable plant. 28.1-BASIS OF DESIGN NORMAN WEISS 28.1.1-SIZE OF PROJECT The size of the project generally is expressed in tons of ore milled per day, but company policies differ widely in this respect, a few adhering to this set figure but many expecting the design capacity to be liberal. To some companies that follow the latter practice a 25,000-tpd milling plant that cannot reach 30,000 or 35,000 tpd without major additions is a disappointment. The engineers responsible for planning the operation must know what is intended. Equally important are operating schedules, particularly the number of operating days per week and shifts per day for ore delivery, crushing, grinding and processing. Hours per shift also are an important factor in design, particularly in the case of ore delivery, and the percentage lost time expected for maintenance, cleanup, inspection, preventive maintenance shutdowns, and many others, has to be taken into account. Frequently, the ore deposit will vary in hardness and grade to such a degree that the capacity of the mill will vary widely from year to year and cannot be expressed as a fixed figure. but rather as an average over a calculable period, such as 10 yr, or as a specific daily capacity over the first 2 yr, next 4 yr, etc., or some similar projection. A good example of this kind of situation is Asarco's Mission operation 15 mi southwest of Tucson, Ariz., described by Weiss and Vincent.' where the major rock types differed widely in hardness, so that a change in the proportion of these types in the mill feed could have imposed difficult design problems if a constant tonnage rate had been expected. 28.1.2-EXPECTED LIFE The life of a mining operation depends upon the size of the deposit and the rate of mining. The latter is a policy decision based on an economic analysis which, in turn, is based on many factors.' From the point of view of mill planning, the estimated life of the operation determines many criteria and affects many decisions on strength of structures and degree of protection of men and materials, the quality of the materials-handling and process machinery, the type of delivery systems for ore to the mill and concentrates to the smelter or market, and many others. Costly installations that may be excellent investments for a 20-yr project may be wasteful for a 5-yr operation. An example is the comparison of different methods of crushing or grinding. Take single- vs. multiple-stage grinding-the former may be found more economical for a 5-yr operation, and the other, more costly, method more economical for a 15 to 20-vi- life.

Jan 1, 1973

By John Duff Erickson

Computer use has become an integral part of mine planning at Kennecott Copper Corporation?s Utah Copper Division, Bingham Canyon mine. Engineers are using the computer for development drilling calculations, mineralization grade interpolations, ore value summaries, long-range mining plans and short- range mining plans. The versatility of the computer has made it possible to explore many mining plan variations and to develop plans covering varying time intervals and production rates. This paper will summarize computer use in long-range mine planning, tell how short-range mining plans are prepared by conventional methods and discuss the development and application of short-range mine planning by computer.

Jan 1, 1966

By Frederick K. A1lgaier

The Bureau of Mines' Denver Research Center initiated a subsidence research program in 1978. The short ten goals of the program were to determine practical methods and equipment for measuring subsidence and demonstrate these methods by monitoring subsidence at several mines having mining, geologic and topographic variables typical of those encountered in the western United States. Data from the monitoring program would be supplied to cooperating mining companies and used by the Bureau to accomplish the long term objective of developing and validating subsidence prediction techniques applicable to mines in the West. Subsidence monitoring is being conducted at five mines in Colorado and Utah with substantially different mine plans, mining methods, depths of cover, and topography. The monitoring procedures used at each site are similar and include designing the monitoring network layout, installing the subsidence monuments, initial and periodic surveying of the monuments, and processing the survey data. The network layout, surveying methods, and types of monuments vary according to the conditions at the individual sites and the type of data being collected.

Jan 1, 1982

By D. L. Madge

The text of this chapter was not received in time for printing.

Jan 1, 1979

By C. E. Schmidt

Homestake crushing and grinding, practice-was completely revised during the period of 1951-1953. During the conversion, both crushing plants at the head frames the Ross and the Yates, were changes at each plant involved replacing the two 8K gyratories with a rebuilt, The flow sheet single thirty inch gyratory for primary crushing to four inch. The gyratory discharges to a seven foot Symons standard cone crusher set at 1-1/8 inch opening. The cone discharge goes to Tyrock screens fed by vibrating feeders. Screen openings, are l/2 inch by 5 inches: at the Ross. Plant, and 3/8 inch by 5; inches at the Yates. Screen oversize goes to a seven foot Symons cone brusher converted to the short head type; the crusher setting is 5/16 inch. Crusher, discharge; is closed circuited with the Tyrock screens, The above crushing installation delivers a minus 5/8 inch rod mill feed to the mill bins. The crushing revision eliminated the-180 heavy South African type stamps, which had previously reduced the 2 inch crushing plant product to a minus 5/8 inch feed for the 10 rod mills, and 8 ball and pebble.; mills, other revisions in the mill flow sheet, resulted in 3 identical units of about 1350 tons per day, capacity per unit, Each unit consists of an open, circuit 6 foot by 12 foot rod mill, fed from two 24 in by 48 inch vibrating feeders of the four feeders available per unit. A gathering belt delivers the ore discharge of the feeders to the Transportoweigher, which in turn discharge s, into the rod; mill feed spout. Rod Mill discharge is the feed for the 9 foot by 11 foot ball mill, The ball mill is closed circuited with a 16 foot by 30 foot Dorr Classifier. The Homestake make amalgamator, for coarse gold recovery in the ball mill circuit, made' necessary a 36 inch spiral conveyor between the classifier rake discharge and, the combination drum and double scoop feeder on the ball mill See Figure l - the flow sheet of the two stage grinding units.

Jan 1, 1958

By A. K. Sinha

Despite the tremendous efforts and costs incurred by the industry and regulatory agencies to prevent premature roof failures in underground mines, roof falls continue to occur frequently due to the very unpredictable geological conditions and dynamic nature of mining operations. In fact, roof falls continue to be the largest contributor to coal mine fatalities. The failure of a mine roof generally occurs following a prolonged, gradual degradation in its physical conditions. An electronic mine roof monitoring system has been developed and tested in operating mining sections. It monitors mine roof degradation on a continuous basis. The field test results are presented and discussed.

Jan 1, 1987

By Joel Nonnweiler, David Young, John Hawley

The Sacramento Regional County Sanitation District has implemented a billion-dollar interceptor system master plan, including the 31 km (19 mile) long Lower Northwest Interceptor (LNWI). For the two LNWI Sacramento River crossings, pipe-jack/micro tunnel drives in excess of 300 meters (1,000 ft) from 30 meter (100 ft) deep shafts in mixed soil conditions below the water table were considered, as were600 meter (2,000 ft) tunnel drives utilizing pressurized-face tunnel boring machines. Operation and maintenance concerns, predicted flood scour, and levee concerns are discussed. A risk assessment process was used to select both profile and construction method. Construction will begin in mid 2004.

Jan 1, 2003

By H. Wesley Peirce

Arizona, in 1966, has continued to be the site of an extensive and intensive search for metallic mineral deposits. Over fifty separate entities--companies and individuals--have been actively engaged in mineral exploration programs, both large and small, in the Basin-and-Range portion of the State. Certainly, copper has been primarily responsible for the major efforts, although associated gold, silver, and molybdenum mineralization also has been important in the economic evaluation of potential copper deposits. It is not difficult to explain why the Basin-Range portion of Arizona is receiving such attention. Part of the story, undoubtedly familiar to most, can be illustrated by reference to three graphical presentations. For example, Figure 1 shows Arizona's annual copper production for the period 1955-1965, inclusive, and it demonstrates that new records of production have been accomplished in each of the past 6 years and in 9 of the last 11 years.

Jan 1, 1967

By G. E. McClelland

Agglomeration techniques have been successfully applied to commerical heap leach cyanidation operations for the recovery of precious metals from low-grade ores, mine wastes, and tailings. The major parameters important for successful agglomeration pretreatment of these feed materials are discussed. Several commercial agglomeration-heap leaching operations are described. Two of the operations converted from conventional heap leaching to agglomeration-heap leaching after coventional heap leaching proved unsuccessful. Heap performance before and after agglomeration is discussed. A fairly recent operation that began production using agglomeration-heap leaching technology is also described. Two operations that processed milled tailings by agglomeration are discussed. The tailings feeds could not have been economically processed by means other than agglomeration-heap leaching.

Jan 1, 1986

By M. W. Brandt

In the November 1957 issue of "Chemical Process Engineering," a British publications, there appeared an article entitled "Correct Selection of Drying Equipment." The author wrote as follows "Whether batch drying or continuous drying' methods are applied, the basis of efficient drying is heat distribution, control of rate of heat input, and heat transference from heating medium to the particles of the material to be dried." The author continues: "Because the efficiency of direct dryers, such as hot air or hot gas dryers, increases with rising inlet temperature of the drying air or gas when exhaust temperature remains fixed, the highest practical drying temperature should be used. Exhaust air should leave the dryer at the lowest possible temperature, but as fully saturated with moisture as possible." It is certainly conceivable that the author of this article by outlining the basic requirements for efficient drying methods has unwittingly given the reasons why fluidized drying is rapidly being adopted for so many industrail applications, including the dryingof fine coal. An examination in greater detail of the individual basic requirements for efficient drying as outlined by the author is perhaps the most logical starting point.

Jan 1, 1958

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION This manuscript is based on site inspections of five existing mines and the detailed analysis of two of the five. The detailed analysis and mathematical models of the two mines are presented herein in order to demonstrate a method of predicting mine water inflow using existing mines as a data base. Water management procedures were studied at all mines. Our original criteria for mine selection were that the mines be less than five years old and have an inflow rate in excess of 2000 gpm (7.6 m3/min). Background hydrologic and hydrogeologic data were required so that two of the mines could be used for our computer modeling experiments. Our original criteria proved to be difficult to meet. We contacted numerous mines via various sources. Many mines were unable to meet the cri¬teria stated or were not interested in cooperating with us. Therefore, we allowed some flexibility in the application of these criteria to satisfy our orig¬inal requirements. Although the visitations at all the mines are not discussed herein the characteristics of the two mines simulated are presented. These simulated mines consist of a uranium mine in New Mexico and a lead mine in Missouri. The mines and owners will remain anonymous by request. URANIUM MINE-CASE HISTORY NUMBER 1 Mine Location The uranium mine that we simulated is located in northwestern New Mexico. The ground surface at the uranium mine is at an elevation of approx¬imately 7000 ft (2134 m) above mean sea level. The climate is arid to semi-arid with an average annual precipitation of approximately 10 in. (25.4 cm) (John and West, 1963). Geologic Setting It is essential that a conceptual model of the stratigraphy, hydrostratigraphy, and structural geology of a mine site be developed prior to simulation by a mathematical model. If such a conceptual model is not developed prior to simulation major errors are difficult to avoid. The uranium mine we have simulated is located in the San Juan Basin (Fig. 68), which is a structural basin located in northwestern New Mexico and adjacent parts of Colorado, Arizona, and Utah. The sedimentary rocks present in the deepest part of the basin are nearly 15,000 ft (4572 m) thick (John and West, 1963). The regional dip of the sedimen¬tary rocks in the Grants area is generally northward toward the San Juan Basin; the regional attitude is modified locally by normal faults and folds (Hilbert, 1963). The rocks of interest in this area are sedimentary in origin and range in age from Penn¬sylvanian to Cretaceous. They rest on the Precam¬brian core of the Zuni Uplift. Associated intrusive and extrusive rocks are of Tertiary and Quaternary ages (Hilbert, 1963). The deepest sedimentary unit of interest at this mine site is the Morrison Formation as described by Hilbert (1963). The Morrison Formation con¬sists of three members in the general area of the mine site; the deepest member is the Recapture. The Recapture Member consists of alternating beds of gray sandstone and grayish red siltstone or mud¬stone with strata up to several feet in thickness. Only a few small deposits of uranium are contained within the Recapture Member. The Westwater Canyon Member overlies the Recapture Member of the Morrison Formation. The Westwater Can¬yon Member is approximately 150 ft (46 m) thick and consists of light brown to gray, poorly sorted, arkosic sandstone, and some interbedded gray mud¬stone. The Poison Canyon Formation denoted in subsequent discussions, tables, and figures was de¬termined to be a part of the Westwater Canyon Member. The separate connotation is used for the description of mining operations and hydraulic properties but a separate physical description is not included. This member of the Morrison Formation contains many large deposits of uranium. This is (some pages in this article are damaged)

Jan 1, 1986

By K. Soucek

Extraction of hard coal reserves, but also of mineral resources in general in the underground coal mines includes in itself many anthropogenic interventions in the earth crust. These interventions are closely associated with the solution of stability problems in the mine and with occupational safety. One of potential applications of such geo-technical interventions in rock mass is the chemical grouting technology. The chemical grouts are very suitable to affect the physical and chemical properties of rock mass. With the present development of chemical grouts, primarily based on polymers, there come into existence new composite materials during the grouting process (the so called geo-composites), which properties significantly differ from the original rock. An important factor, which affects a choice of chemical grouts and at the same time the effectiveness of grouting technology is the resulting properties of geo-composites. The properties of a coal geo-composite differ from the ones of the unmodified coal seam. On the basis of the laboratory geo-mechanical tests, the differences of properties of both material types were found. While the pure coal samples were destroyed very brittle and explosive, the geo-composite samples were making higher level of tenacity and load bearing ability after overstep of material strength. The presented paper discusses the different behaviour of these original and modified coal samples. The X-ray CT scans were used for observation and demonstration of failure evolution in these samples of pure coal and coal geo-composites after compressive loading.

Jan 1, 2006

By Thomas A. Earl

Strip mining of coal, and to a lesser extent limestone, gravel and other mineral deposits in the Appalachian region of the eastern United States has left many large and small areas of devastated land where mining predated reclamation requirements. In Pennsylvania alone, there are between 250,000 and 370,000 acres of strip-mined land 1,2/. A higher percentage, and a greater total acreage of land in Pennsylvania is in need of some form of reclamation than any other state, with the neighboring states of Ohio and Nest Virginia also having nearly the same magnitude of mining.2/ Recent legislation governing strip mining of coal proposed royalties to cover reclamation of such presently unusable land. However, in Pennsylvania and other states some progress has already been realized by utilizing abandoned strip mines and gravel pits for waste disposal sites. Given acceptable hydrogeologic settings, such use of these mined areas for landfilling has provided the incentive for ultimately restoring unreclaimed land to beneficial use, at no cost to the general public.

Jan 1, 1975