Search Documents

This paper presents a method for evaluating the economic feasibility of solution mining a hypothetical uranium roll-front deposit. It is assumed the wellfield will be operated in a prudent manner and that leaching tests were performed in depth in both lab and field (push-pull) prior to startup. Leach test results are reduced to two important parameters and used as the basis for solution mining a wellfield. This case study assumes a 10 mil- lion-lb uranium deposit with 40 possible small wellfields; four are kept in operation simultaneously until the deposit is depleted. The wellfields have different ore reserves and grades, lixiviant circulation rates, leach rates, and peak concentrations, and thus the daily uranium production will vary. Daily production is used to assess the profitability of a particular lixiviant and the mode of well- field operation in light of realistic market price estimates. The mathematical procedure is simple and straightforward, based on reasonable in-situ leaching relationships as well as accepted accounting practices.

Jan 1, 1985

By Louis I. Briggs

Evaporite rocks, salts of the more soluble ions in seawater, are deposited when seawater becomes concentrated by excess evaporation in marginal basins having restricted circulation with the open sea. The simple conceptual model of an evaporite basin (Figure 1) has a single inlet connecting the basin to the open ocean, the restriction to open circulation being caused by a bar or reef near the mouth of the inlet. As the oceanic water flows from the inlet into the basin it tends to form a thin layer of brine that spreads out over the surface of the basin brine, and as it does so, the salt concentration In the surface layer gradually increases owing to continued evaporation of the water. When the solubility products of the salts in the surface layer are exceeded, the salts precipitate and settle to the bottom of the basin, The order of precipitation follows their order of least solubility. Normally the carbonates separate first, followed by the sulfates and chlorides and the more complex double salts. In nature there is considerable overlap in their ranges of precipitation. The water flow in the basin, also shown schematically in Figure 1, diverges from the inlet essentially perpendicular to the lines of' equal salinity in the surface brine. The distribution of salts deposited in such a model will parallel the isosalinity lines, being arcuate and concave toward the inlet (1)

Jan 1, 1967

By N. Hoffman

Accurate, repeatable density measurements of a coal-magnetite-water slurry are difficult to achieve using a nuclear density gauge. Changes in the coal-to-magnetite solids ratio cause fluctuations in the readings of nuclear gauges. To investigate this problem the Electric Power Research Institute's Coal Cleaning Test Facility compared the performance of a nuclear density gauge on a coal-magnetite-water slurry with the performance of a differential pressure gauge modified with a new pressure sensor. A second aim of these preliminary tests was to determine if the differential pressure gauge is also sensitive to the type of solids in the slurry. This paper explains current slurry density measurement practices, describes the nuclear and differential pressure gauges used in the CCTF tests, and presents test methods and results.

Jan 1, 1986

By T. Cantwell

Techniques useful in operations, analysis are applied to the problem of planning an exploration program. The model used treats mineral exploration as a Markov process, and maximization of gain is the criteria determining the optimum program. The mathematical description of the model and the optimization are first worked out. Application of the mathematics to several simple examples is given. Finally, comparison of the data necessary to use this operations analysis with the available data shows that the method can only be a guide to planning an exploration program.

Jan 1, 1962

By Richard E. Barrett

The relationship between coal characteristics and power plant performance has become a matter of increasing interest to utilities. This relationship can affect the value of coals, decisions as to coal washing, setting penalties for delivery of coal that fails to meet specifications, and justifying buying better coals (at higher costs) before public utility commissions. The study described in this paper was directed to identifying how coal characteristics impact on boilers and related coal and gas handling systems. TVA data for the period 1962-1980 was the basis for the study. Models were developed for boiler efficiency, boiler availability, and maintenance costs as a function of such coal characteristics as ash, sulfur, and moisture content and boiler age. Boiler load and maintenance efforts were considered as variables in some of the models, but were found not to be statistically significant. Although the results of this study are strictly applicable to only the TVA system, they can serve as guides or first approximations for other utilities.

Jan 1, 1983

By K. A. Natarajan

The relative significance of corrosive and erosive wear in magnetic taconite grinding is examined. The influence of different types of aeration, namely, nitrogen, air and oxygen on ball war was established for mild steel and high carbon low alloy steel balls. Ball wear data from dry and wet grinding tests are compared with those obtained in the presence of an organic solvent that does not promote electrochemical corrosion. 'Marked ball grinding, tests along with electrochemical measurements involving ball material and magnetite electrodes indicate that contribution from oxygen towards wear (corrosive wear) is relatively small and abrasive wear appears to be significant. Rheological properties of the slurry-appear to have an important bearing on the abrasive wear of grinding balls.

Jan 1, 1983

By Dave G. Osborne

With the growing exportation of coal from North America to the Pacific Rim countries and Europe, has come an increasing awareness of the need to determine economically optimized amounts of incombustibles (ash and moisture contents) for the shipped product. Despite the fact that demand bas caused a steady improvement in selling price, particularly for thermal coals, growing production and transportation costs have compelled producers to keep a sharp eye open for ways and means of minimizing the latter since this probably represents the greatest single potential for making savings. Consequently the Coal Industry has become acutely aware of the economic ramifications of eliminating moisture in particular, thereby producing further saving in the cost of transportation of product from the mine to the consumer. There is, however, a lower limit to which dewatering or drying can be taken and this relates to dustiness which is a function of the characteristics of the coal and the methods used for handling and storage during trans-shipment. Overdrying can lead to serious dust losses and difficulties in handling particularly if the coal contains a large proportion of fines. The ways and means for achieving this "happy medium" of optimization in moisture removal are seemingly undergoing gradual modification largely assisted by the following factors. a) Improvement in effectiveness of coal dewatering and drying equipment. b) Improvement in operational availability and utilization of the equipment. c) The development of surfactants, polymer flocculants and other agents which in many cases can be almost tailor made to suit specific applications.

Jan 1, 1982

By Yao Dun-Pu

Solution mining, sometimes also refered to as chemical mining or bacterial mining, is an innovative technology which, by making use of proper chemical reagents and taking advantage of bio-chemical action of some micro-organism species, can dissolve effectively most. desirable metallic values from ores and then extract them profitably from the resultant metal-bearing solution by suitable means to form the metal product it is more preferable to the conventional mining methods, not only because of its capability to improve working conditions and minimize environmental problems either underground or on surface, but also for its amenability in particular, to exploit low-grade or submarginal ore bodies, or those deposits which are too deep-seated to be mined out economically. Furthermore, it also provides a potential approach to win metals directly from their ores or ore-deposits in-situ by more simplified methods and at a lower cast than the conventional mining-milling-smelting process would do previously. Hence, in developing countries such as China, it will most, probably become a new mining tool of great promise. (1)

Jan 1, 1981

By S. E. Sankey

High anionic functionality acrylamide co-polymers and poly(sodium acrylate) are used as red mud flocculants in bauxite processing operations. These synthetic polymers are effectively displacing starch as the dominant polymer in red mud settling. The performance of these polymers is primarily dependent on the bauxite mineralogy, the alkalinity of the red mud slurry, and the anionic functionality and molecular size (viscosity) of the polymer. In this paper, the physical and chemical properties of the synthetic watersoluble polymers will be reviewed. The relationship between polymer structure and red mud slurry properties as they control polymer performance in settling red muds common to digester and washer circuits will be illustrated. The availability of polymers of varying functionality and viscosity will permit bauxite processors to make significant improvements in the economics of red mud disposal and valuable reagent recovery.

Jan 1, 1982

By Fred C. Caspall

During the last century the importance of coal as a natural re- source has frequently come to the attention of the general public, but never before nave circumstances combined to focus as much attention on coal as it receives today. There is the ever increasing demand for energy that can be met only by coal consumption, coupled with a growing awareness of man's potential for despoiling his own environment. Society monitors the use of the remaining resources with an increasingly critical eye and, for obvious reasons, surface mining operations tend to draw an unusual amount of public attention. While the surface mine is a successful economic competitor with other uses of the earth's outer skin, one of the unrewarding results of such activity is tile simultaneous destruction of two of our most important resources--the coal seam and the surface soil. In a relative sense the coal seam is a nonreplaceable resource but the surface soil can be restored. Unfortunately, little attention has been given to land reclamation and even less has been devoted to the restoration of a productive surface soil. The research reported in this paper was de- signed to test the relative productivity of newly reclaimed surface mine spoils in western Illinois. The results are preliminary in nature but may aid in the future redevelopment of mine spoil soils in the Illinois Coal Basin.

Jan 1, 1975

By Bennett D. Lass

A new method for determination of residual flotation oils on beneficiated kaolin clays has been developed. The method, which yields qualitative information, is based on fluorescence measurements employing a spatially resolved, polychromatic illumination source for excitation, and a two-dimensional detection scheme using a silicon-intensified, video imaging device. The method was used to identify residual oils on a beneficiated, Washington County, Georgia, crude clay. The results were compared to a similar qualitative analysis performed via capillary column gas chromatography using an FID detector. The video fluorometry was the preferred method of, analysis.

Jan 1, 1983

By Sun K. Kim

Hydrometallurgical processes are not free of environmental regulations. A clear understanding of the regulations under which the minerals industry operates delineates processing requirements at early stages. This paper deals' with federal environmental regulations with emphasis on the hazardous waste regulations promulgated in May, 1980. The procedure of EP toxicity test and an example of the test are described. Brief account is given of the current trend and future outlook of regulations.

Jan 1, 1982

By John T. Awald

The Bradshaw Mountains of west-central Arizona cover an area of 1600 square miles and contain numerous old mines and prospects. The area has been geochemically sampled on a reconnaissance basis to relate mineralized areas to regional structure and rock types. Copper analyses of stream sediments have been classified and contoured to show the distribution of low background, high background, and low, intermediate and highly anomalous areas. Contoured results are compared to geology and known mines. Several prospecting areas are indicated.

Jan 1, 1970

By G. Thorsen

An alternative way to the normal practice of precipitation of jarosite, goethite, or hematite for removal of iron from zinc sulphate process liquors/ is to employ the techniques of solvent extraction. The process presented avoids the addition of any external alkali for the extraction of iron by integrating the leaching and solvent extraction steps in a hydrometallurgical zinc plant. By starting the leaching of zinc from the solid zinc calcine material with an organic solution of an acid liquid cation exchanger, the organic phase is loaded with the organic zinc salt from the direct reaction with zinc oxide. The residue from the organic leaching is transferred to a hot acid leach circuit where the remaining zinc oxide and the zinc ferrites will dissolve form¬ing an aqueous sulphate solution of zinc and iron. In the subsequent solvent extraction of iron from this aqueous leach solution, iron is exchanged with zinc from the organic phase. The commercial carboxylic acid Versatic 10 (Shell) is highly efficient for this integrated process of leaching and solvent extraction. The resulting iron-loaded organic phase is heated to 150-200 C in the presence of water whereby the iron will be directly precipitated from the organic phase as iron oxide of high purity and the regenerated organic acid is recycled to the organic leaching step for reloading with zinc.

Jan 1, 1980

By Charles H. Ricker

Simulation models have been widely used to analyze the operations and characteristics of a variety of systems. Such models mimmick a projected reality by analyzing the interaction of the events, transactions, and facilities which combine to make up the system. The models are structured as a computer representation of the system components and their logical, precedence and timing relationships. The operation of the system is then simulated over some finite time interval to gather analytical and staistical data. This paper presents a method whereby bulk handling systems, either actual or proposed, may be analyzed by means of simulation models to project the enconomic consequences which may be expected from the system over some future time interval. An example is given to illustrate the construction of bulk handling simulation models, the derivation of performance data, and the analysis of the information with an eye to effective decision making.

Jan 1, 1974

By Tsutomu Yanagase

Non-ferrous smelting industry in Japan often had the severe problems about the over production of sulfuric acid. There has been such a closed relation between amount of sulfuric acid from non-ferrous smelting industry and the products of copper, zinc and lead metals that the production of one ton of copper accompanies three tons of H2S04. When the proper balance exists in both markets this situation certainly brings bigger profits. In Xining and Metallurgical Institute of Japan the research commitee concerned with the fixation process of sulfur in non-ferrous smelting industry was established in 1977 and continued the activity for four years untill 1981. This paper will introduce some of the activities involved in the report published by the committee.

Jan 1, 1982

By T. E. Burns

The process engineer is frequently requested to select equipment to separate brine from solids, In many cases, this is a more difficult task than the selection of most other pieces of process equipment because quite often the operation of the various types of debrining equipment cannot be predicted by calculations, One must rely to a great extent upon experience or empirical test work to predict performance - that is to say one must use a practical rather than a theoretical approach. This is not to say that the solutions to liquid-solids separating problems are wholly an art but rather it is to emphasize that the approach demands a fair knowledge of commercially available liquid-solids separating equipment, some background on the advantages and limitations of each type and in many cases might necessitate a fair amount of test work, or at least, a study of performance of equipment on similar applications.

Jan 1, 1966

By M. P. Saunders

A comprehensive, site specific water management plan is of primary importance to the successful implementation, operation and decommissioning of any mining project. Formulation of a plan requires an orderly planning process consisting of identifying problems, establishing planning criteria based on the guidelines and requirements of regulatory agencies, and an iterative procedure of identifying, investigating, and evaluating plan elements and alternative plans. A typical uranium surface mine operation consists of a mine pit or pits, spoil pile areas, crusher, processing plant, and tailings disposal area. A water control plan addresses the problems of diversion of natural runoff from undisturbed areas around the mine; and diversion, collection, and treatment of runoff from within the mine area. A water control plan is required to determine the location and size of appropriate control and detention structures; their cost; and the schedule for permit activity, design, and construction. The plan must be formulated to meet the requirements of both the State and Federal regulatory agencies.

Jan 1, 1981

By James R. Craig

The Central and Southern Appalachians were the major sources of gold in the United States throughout the first half of the 19th century and have continued to yield gold to the present day. Small amounts of gold were probably extracted by the Indians and the Spaniards but the first documented report of gold in the region was made by Thomas Jefferson who found a four pound lump of gold ore, which yielded 0.85 troy oz., in the Rappahannock River of Virginia in 1782. Gold was subsequently discovered in North Carolina between 1793 and 1799, in Virginia in 1806, in South Carolina in 1827, in Georgia in 1829 and in Alabama about 1830 (Becker, 1894-5; Pardee and Park, 1948). The gold belts of the Central and Southern Appalachian Piedmont and Blue Ridge Provinces are shown in Figure 1. The superimposed circles indicate the mount of production from some of the more productive and well known areas. Although North Carolina produced far more gold than the other states, the most significant concentrated area of production is the Dahlonega District in Georgia which yielded more than 500,000 troy ounces. After discovery, gold production increased rapidly as shown in Figure 2. Production was at its maximum between 1830 and 1852 with combined totals generally exceeding 30,000 troy ounces per year. Production dropped sharply after the California gold rush in 1849 as experienced miners moved westward in search of bigger and easier stakes. After the Civil War briefly halted gold mining in the Appalachians, production rose to an average of about 8,000 ounces per year from 1865 until 1878 and to an average of about 13,000 ounces per year from 1881 until 1915 when it again fell to near nil (Pardee and Park, 1948). Minor resurgences occurred in the 1930's and 1940's. Although there has been no reported production in recent years, it is likely that "weekend panners" still remove hundreds of ounces from streams annually. The total reported production for the area through 1959 is in excess of 2.5 million troy ounces.

Jan 1, 1981

By V. I. Lakshmanan

Crystalline Flake Graphite is a strategic mineral. Since 1954 nearly all North American consumption has been imported from offshore. The Bouthillier Project in Quebec, Canada, is Orrwell Energy's bid to enter the market. Milling of flake graphite is considered easy, yet more problems have been encountered in flowsheet and plant design than in most other minerals. A fresh approach to existing technology was taken, giving results that are highly satisfactory. The key to graphite liberation without flake deterioration is found to be in autogenous grinding. In addition to producing marketable coarse graphite by such autogenous grinding, flotation and tabling, super purity fines can be produced using repeated regrinding, elutriation and flotation. This paper discusses the design of a 500 TPD plant based upon the results obtained from bench and pilot plant studies.

Jan 1, 1984