Search Documents

By D. S. Kostick

Soda ash production in the United States during 1994 increased 4%, reaching 9.3 Mt (10.2 million st). That was the second highest production year. Domestic nameplate soda ash capacity is about 11 Mt (12 million st). Overall, the industry operated at about 85% of capacity. Some companies produced at 100% of capacity while others produced at below their design ratings. Although domestic soda ash consumption was slow during the first half of the year, third- and fourth-quarter sales increased, especially in the flat¬glass and fiberglass sectors. These two sectors increased because of greater demand for glass products in the automotive and construction industries. Soda ash sold for pulp caustic soda increased during 1994. This was due to higher prices for and reduced availability of electrolytic caustic soda. It is often preferred for pulp digestion because of its stronger alkalinity.

Jan 1, 1995

By T. P. Lim, J. A. Cherry, A. J. Vivyurka, R. D. Blair

The first phase of an investigation of the chemical composition of subsurface water and the hydrochemical processes in and near the abandoned Nordic tailings at Elliot Lake, Ontario, was conducted in 1979. The Nordic area, which covers 85 hectares with an average thickness of 10 m and overlies deposits of permeable glaciofluvial sand, contains 15 million tonnes of tailings with 4-7% pyrite. Nests of standpipe piezometers installed at three locations on the tailings indicate that seepage through the tailings is predominantly downward. The water table in the tailings slopes from the north side of the tailings dam, where it is within a metre of surface to the south side near the tailings dam, where it is approximately 10 m below surface. When they were deposited during the period from 1957 to 1968, the tailings contained pore water at a pH of about 8 resulting from neutralization treatment in the mill. At the three piezometer nests, the pH increases from 3 near the water table to 7 near the bottom of the tailings. The pore water in the tailings is gradually becoming acidic because of oxidation of pyrite in the zone above the water table. The concentrations of Fe, Mn, Ni, Co, Zn and Pb are high in the shallow acidic zone and much lower in the deeper neutral zone. Concentrations of 226Ra range from 30 to 230 pCi/L. At the three sites concentrations of major ions in the permeable sand a short interval beneath the tailings indicate 226Ra presence of tailings seepage, but Ra concentrations are only 2 to 8 pCi/L. Greater downward penetration of 226Ra probably occurs in the area closer to the tailings dam. Monitoring of a network of multilevel bundle piezometers installed in permeable sand that extends southward from beneath the tailings indicates the occurrence of a plume of tailingsderived water containing high concentrations of Ca, Mg, Fe and S04 that extend 400 m downgradient from the tailings dam. The total dissolved solids decline from 20,000 at the dam to less than 500 mg/L at the identifiable downgradient periphery of the plume. A much smaller but distinct plume of water with high heavy metal concentrations and 226Ra in the range of 10 to 130 pCi/L extends from beneath the dam for a distance of 15 m. The pH of the groundwater in this heavy metal-radium plume is 4 to 5, whereas elsewhere in zone of groundwater with high dissolved solids, the pH is above 6. The results of this investigat, suggest that the heavy metals an 226 Ra are relatively immobile in the perme-

Jan 1, 1980

By L. Adler

A fairly complex analysis is required to select, or evaluate a piece of excavating and bulk handling equipment and obtain its performance. At present there is little agreement as to what specific points should be considered, and even less on what procedure to follow. This paper provides both of these in a consistent and direct form. The analysis applies to all types and sizes of equipment from the bulldozer and the continuous miner, to the B.W.E. The importance of the equipment characteristics, job activities, and work conditions are stressed and separate analytical stems are established in a flow chart for these. They are combined using suitability tests in the following steps: 1) problem statement, 2) natural conditions, 3) suitability guidelines, 4) appropriate equipment types, 5) operational activities, 6) encumbered space, 7) geometric design, 8) equipment sizing, 9) failure and limits, 10) performance and consumption, 11) public policy checks, and 12) costs and profitability. Public policy and economics while considered throughout receive emphasis towards the end. The procedure is iterative, containing distinct feedback loops. Specifying the steps and sequence provides a necessary structure which has long been overdue.

Jan 1, 1983

By J. E. Osmanski

This semantically ambiguous title purports to describe an examination of the question of automation and its effect on the industrial worker. More explicit titles might be "Painless Automation" or "Mechanization without a Sting" or, if I may steal a few phrases from the title of a recent interview Pith John L. Lewis, "More Machines, Fewer Men -- Is the Union Happy About It?" Automation has become the biggest ?scare word? for many industrial workers and their unions since "wage stabilization.? "To many a union orator," reports TIME of January 4, "automation is the sinister business of eliminating jobs." TIME might better have phrased this description by saying that many unions regard automation as the attempt to eliminate not jobs, but workers, The recent steel dispute was hung up for so long primarily because of the problems evolved of increased job efficiency through automation and job changes. Everywhere today there is heard the cry of our need for maintaining full employment within the context of an expanding economy echoing against the sheer reality of automation's displacement of thousands of workers through a rapid acceleration of productivity.

Jan 1, 1960

By P. Somasundaran

Previous studies on semi-soluble minerals such as calcite (1) and apatite(2) and sparingly soluble minerals such as quartz (3,4) have given evidence for significant changes in their electrokinetic properties as a function of aging time. Such changes are relevant to mineral processing operations where the crushed ore particles might not have yet reached equili¬brium with the water that it is in contact with. In order that these changes be studied under controlled experimental conditions for long periods unattended or with fairly less intermittant attention, a streaming potential apparatus with an automatic streaming system was constructed. Also, a new streaming potential cell was incorporated into the system so that the effect of temperature, a variable coming into increasing usage in mineral processing operations(5), could also be studied. Conventional streaming cells(6) cannot be safely employed to conduct studies as a function of temperature since they have many glass joints that are prone to leakage, parti¬cularly under pressure, in the course of an experiment. This paper describes the new apparatus and some typical results that have been obtained with it far temperature effects.

Jan 1, 1973

By J. C. Reid

Computer-aided lithogeochemistry was used to "prospect" for stratabound scheelite (a tungsten ore) that occurs in many Precambrian clastic and chemical rocks, northeastern Brazil; The district is a metallogenic province covering about 5000km2. Exploration bedrock lithogeo-chemistry was applied at regional, local, and mine scales to identify regional tungsten trends and dispersion halos associated with economic tungsten mineralization. Regional coarse-mesh sampling (Cu,Mo,W) in 25km2 cells "found" all major mines and significant prospects using objective and cost objective computer mapping of bedrock geochemical data. The method is efficient ; of the 3600km2 study area only 9% of the original area remained after the initial pass. Of this area, the geo- chemically highest ranked (4%) cells contained the mines and prospects. Similar computer-aided treatment was applied to Cu,Mo,W,F, and Be lithogeochemical data from several mining concessions and prospects with outcropping and subsurface W mineralization. At a local scale out-cropping W mineralization was recognized at a distance of 500m. Fracture zones through which hydrothermal solutions traveled were identified; these were related to W mineralization at a depth of 200m.

Jan 1, 1986

By M. J. Sanzotti, C. J. Bise

This paper examines the potential for controlling longwall-induced subsidence by pneumatically backstowing waste rock into the void created by mining. The paper also examines scheduling the process as a unit operation of the mining activity. Based on a review of background literature and interviews with representatives of various mining companies, public-interest groups and state and federal regulatory agencies, a hypothetical case-study evaluation of pneumatic stowing at a southwestern Pennsylvania mine was conducted. The study indicated that current stowing technology cannot keep pace with the production potential of longwall systems in the United States. Further, at the mine used in this case study, concomitant stowing would reduce subsidence by only 50% of what would normally be incurred during full longwall caving, and the longwall coal-production rate would decrease from 3,630 t (4,000 st) per shift in the nonstowing case to 1,360 t (1,500 st) in the stowing case. A preliminary cost analysis reveals that pneumatic stowing would add from $5.79 to $11.57 per t ($5.25 to $10.50 per st) to the operating cost of producing coal at the case-study site.

Jan 1, 1997

By D. A. Rice, R. G. Swanton, A. May, O. C. Carter

As part of a cooperative effort between the US Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input from the phosphate industry, the conversion of phosphogypsum to sulfur is being investigated. The proposed process incorporates a thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to ammonium bisulfide (NH4SH), which is then oxidized using a catalyst to produce elemental sulfur. The paper summarizes the results of continuing laboratory studies using an activated carbon catalyst which was loaded with sulfur through oxidation of ammonium bisulfide solution. The extraction of the sulfur that forms in situ on the catalyst is a key area in the development of the sulfur recovery process. Two approaches for removing the sulfur are being investigated: (1) thermal treatment to volatilize sulfur. and (2) leaching the sulfur using liquid anhydrous ammonia. The research has shown that it is technically feasible to recover over 90% of the sulfur from the carbon by either volatilization or ammonia leaching. Locked cycle testing has demonstrated that the carbon has the potential to be recycled after ammonia leaching.

Jan 1, 1987

By Richard H. Follis

Activated carbons used for precious metal recovery from carbon-in­pulp (CIP), carbon-In-leach (CIL) and carbon-in-column (CIC) circuits often become fouled with Inorganic precipitates (i.e., CaCOa, CaS04, SI02), and adsorbed organics (I.e., petroleum distillates from lubricants, dissolution products from wood) (1,2). These contaminants occlude carbon pore structure, such that diffusion controlled adsorption and desorption (elution) of Au(CN)2-and Ag(CN)2· are lmpeded(3,4l. Thus, after only short exposure to the hydrometallurgical environment, the characteristic carbon activity is reduced(5l. By frequently regenerating circuit carbons, activity losses associated with fouling can usually be minimized. Regeneration typically Involves (not necessarily Is this order): 1) elution to remove adsorbed ionic species (e.g., until they are removed from the carbon pore structure, Au(CN)2" and Ag(CN)2-are contaminants )(6l; 2) acid washing with 3-15% (wt/wt) hydro­chloric acid, to dissolve soluble Inorganic precipitates such as CaC03; 3) neutralization and/or water rinsing to remove residual acid; 4) thermal regeneration at 350-650 °C to remove adsorbed and/or pyrolyzed organ­ics; and 5) screening to remove fine carbon particles produced by Impaction and abrasion in the various stages of the hydrometallurgical circuit (i.e., adsorption, elution, and regeneration). The overall process Is purposed to reopen the circuit carbon pore structure, and to maintain the activity and qualities of virgin (new) carbon(7,8l. While most CIP, CIL and CIC operators regenerate circuit carbons, few evaluate the effect of the process on carbon quality in a systematic way. Process control usually Involves Iterating critical regeneration parameters such as: acid concentration; time frames for acid washing and water rinsing; and temperature and residence time for thermal regeneration. Carbon quality control frequently comprises only sporadic activity tests performed on non-representative grab samples dipped from conve­niently accessed carbon storage bins. So, regenerated carbon quality may vary and (at times) be unacceptable for effective hydrometallurglcal circuit operation. To verify the efficacy of the regeneration process and assure accept­able adsorption and elution rates for Au(CN)2· and Ag(CN)2·, operators should systematically assess regenerated circuit carbon quality. This paper, then, suggests methods for effectively assessing circuit carbon quality, Including: carbon sampling procedures; standardized physical and chemical test methods; and criteria and general procedures for comparative adsorption rate (activity) testing. Also, a two tier quality control testing scheme is proposed, and techniques for presenting and interpreting test data are demonstrated.

Jan 1, 1992

By Wendell H. Wiser

A comparison is presented of coal pyrolysis at temp¬eratures ranging from 4090 to 497°C and thermal dissolution of coal in tetralin at temperatures ranging from 350° to 450,°C, both utilizing a Utah high-volatile bituminous coal. The initial coal pyrolysis reactions are second order with an enthalpy of activation of 35.6 kcal per mole. The fraction of total product yield produced under second order conditions ranges from 67% at 409°C to 96% at 497°C. The process then gradually deteriorates to a first order reaction in the later stages with enthalpy of activation of 4.1 kcal, per mole. The initial reactions of solution of coal in tetralin are second order with an enthalpy of activation of 28.8 kcal per mole. The fraction of total product produced under second order conditions ranges from 63% at 350°C' to 94% at 450°C. The dissolution process then gradually changes to first order in the later stages with enthalpy of activation of 15.6 kcal per mole. A model is presented which relates the two processes and explains, the significance of the above similarities.

Jan 1, 1967

By Stanley C. Suboleski

The increase in productivity which has been achieved in mining during the past two decades has been attained largely through the replacement of manpower with electrical power. Power demands should continue to increase, requiring electrical distribution systems to be well planned to avoid inadequate voltage levels caused by underdesign and excessive costs resulting from overdesign. To aid the mining electrical engineer in designing proposed power systems or analyzing changes to existing systems, a digital computer program has been developed. This program will analyze alternating or direct-current networks with up to 10 voltage sources, 75 loads and 300 total segments. A maximum of nine levels of voltage is permitted in the system. This project was part of a package of programs developed at Virginia Polytechnic Institute (WI) for the mining industry under sponsorship of the Office of Coal Research. Included in this package are also programs to: 1. Schedule mine production and predict cost of mining 2. Simulate rail haulage systems 3. Simulate belt haulage systems 4. Analyze ventilation networks 5. Analyze pumping networks These programs are available from the Department of Mining Engineering, VPI, Blacksburg, Virginia 24061 for a nominal processing cost.

Jan 1, 1970

By R. W. Smith

A number of investigators have studied the electrokinetic potential (?) of kaolinite as a function of pH. (1,2,3,4,5) These investigators all agree that the ? is negative except at quite acid pH values. The actual shapes of the curves reported by the several authors vary considerably. In spite of the general negative character of kaolinite the mineral has a rather high anion exchange capacity. (6,7,8) The cation exchange capacity is the lowest for the clay minerals. (6) It has been shown that anionic surfactants adsorb readily onto the mineral even up to neutrality, often in quantities exceeding the reported anion exchange capacity. (7,8) At least part of the anionic adsorption should be onto positive edge sites thought to exist on the mineral. (9,10) In the present study ? of kaolinite was measured as a function of pH using both the streaming potential (sp) and microelectrophoresis (m.e.p.) methods. In addition ? was measured at various pH values as functions of sodium dodecyl sulfate (SDS) and trimethyldodecylammonium chloride (TMDAC) concentrations. In some experiments decyl alcohol (DA) was added.

Jan 1, 1968

By John D. Shaw

1. Introduction 2. The Hydraulic Mine _ (i ) Development (i i ) Extraction ( i i i ) Transport 3. The Water Circuit 4. Manpower and Results 5. Modifications 6. Conclusions 1. Introduction The Kaiser Resources Ltd. hydraulic coal mine is located in south eastern British Columbia, Canada, at the western end of the Crowsnest Pass, next to the Town of Sparwood. The seam presently being mined is the number 10, known locally as the Balmer seam, which is a high quality coking coal, 50 feet in thickness and of an average inclination of 35 degrees. The mine was designed in the late sixties as a small scale trial unit, and was to use a single monitor unit, working 3 shifts per day on a 5 day per week basis. Experience has proved the method to be so successful as to warrant the expansion of the ancilliary facilities to cater for the increased production. The annual raw coal production from this single monitor unit has risen from 108,988 short tons in 1970 to 942,334 short tons in 1975, with a total mine labour force of about 160 men including the surface de-watering plant, mine supervision and mine administration.

Jan 1, 1977

By Sheldon P. Wimpfen

Under the Wilderness Act of 1964 and the accompanying House Conference Report, the Geological Survey and Bureau of Mines are charged with the responsibility of making recurring mineral studies of wilderness and wilderness candidate areas in national forests within and proposed for the National Wilderness Preservation System. The Wilderness Act, a major shift from the multiple-use concept of national forests, identified for the first time the value of mineral resource information in decisions for single-use designation of public lands. This concept was further realized when the Secretary of the Interior in May 1974 recommended that mineral studies be made prior to wilderness recommendations for five large Interior-managed game ranges and the Glacier Bay National Monument aggregating 7.8 million acres. Presently, our studies have been completed on 126 wilderness and proposed wilderness areas totaling 15.4 million acres in the national forests. In 1973, 1 year in advance of the act's 10-year review deadline, we completed the 34 primitive areas, originally the only potential additions considered by the 1964 Act.

Jan 1, 1975

By L. S. Harris

The application of briquetting in various chemical, mineral, mining and metallurgical processes has been rapidly increasing in the past two decades. This is, in part, due to the development of new, more economical and higher performance briquetting equipment. Some of these developments, which have reduced the operating and maintenance costs,, include anti-friction bearings, hydraulically applied pressure enclosed and sealed gearing and bearings, tapered predensification feed screws, water cooling and materials of construction capable of operating at temperatures up to 18000F, and control systems capable of maintaining optimum briquette quality control. The briquets can be formed into almost any desired size and shape, To date, with present rotary briquetting presses in the 25 to 500 ton force range, briquets from 1/4" to 6" length are presently being used, some of which are illustrated in Figure No. 1. In force fed rotary briquet machines, these shapes are produced by feeding the material in between a pair of counter rotating rolls, as illustrated in Figure No. 2. The rolls have forming dies indented into their circumferential surface, as illustrated in Figure No. 3.

Jan 1, 1973

By Robert A. Jankowski, John J. McClelland, Charles Babbitt

The purpose of this study was to develop guidelines to enable mine operators to maximize longwall dust reductions, while optimizing the use of ventilating air and shearer water consumption. A recent investigation by Foster-Miller Incorporated, under a Bureau of Mines contract, quantified the effect of increased face airflow and shearer water supply on face dust concentrations. A 70 pct reduction in respirable dust levels was achieved at the shearer operator's position during tail-to-head cutting by an incremental increase in average face air velocity from 83.8 m/min (275 fpm) to 123.4 m/min (405 fpm), while holding shearer water consumption constant. A 60 pct reduction was achieved through an increase in shearer water pressure and flow from 9.1 kg/cm2 (130 psi) at 0.19 m3/min (50 gpm) to 19.7 kg/cm2 (280 psi) at 0.28 m3/min (75 gpm), holding airflow constant. The combined effects of increasing both parameters produced an 85 pct reduction. Optimal usage of ventilating air and shearer water consumption can be achieved by defining a "point of diminishing returns" above which further increases no longer reduce dust concentrations, proportionately .

Jan 1, 1987

By G. T. Lineberry, R. S. Mateer

Often only after years of "technical dormancy" do errors in published literature become apparent and meaningful. To prevent duplication of effort for future generations, the fol¬lowing corrections are offered. These errors were discovered during a recent study in which a computer program for mine hoist rope selection was developed (Lineberry and Mateer, 1988). In order of increasing gravity: Captions for Figs. 3 and 4 are transposed. • Purported to be a more accurate method of rope selection than the process of successive approximation, the direct method assumes linearity between a given rope's minimum breaking strength, T, and unit rope weight, Wv. Because of the sensitive location of the constant, K, in equation (8) for breaking strength, the significance of this nonlinearity is magnified. For a typical 6 x 37 class fiber core wire rope (Wire Rope Corp. of America, 1985), K actually varies from 43,650 to 52,190, depending upon rope diameter. Although the direct solution permits a rapid selection of hoist rope, an indirect (iterative) solution procedure is favored because of its im¬proved accuracy and ease of computerization. • Equation (8) for minimum breaking strength is in error. It should read:

Jan 1, 1989

By G. T. Lineberry, R. S. Mateer

Often only after years of "technical dormancy" do errors in published literature become apparent and meaningful. To prevent duplication of effort for future generations, the following corrections are offered. These errors were discovered during a recent study in which a computer program for mine hoist rope selection was developed (Lineberry and Mateer, 1988). In order of increasing gravity: Captions for Figs. 3 and 4 are transposed. Purported to be a more accurate method of rope selection than the process of successive approximation, the direct method assumes linearity between a given rope's minimum breaking strength, T, and unit rope weight, WV. Because of the sensitive location of the constant, K, in equation (8) for breaking strength, the significance of this nonlinearity is magnified. For a typical 6 x 37 class fiber core wire rope (Wire Rope Corp. of America, 1985), K actually varies from 43,650 to 52,190, depending upon rope diameter. Although the direct solution permits a rapid selection of hoist rope, an indirect (iterative) solution procedure is favored because of its improved accuracy and ease of computerization. Equation (8) for minimum breaking strength is in error. It should read:

Jan 1, 1990

By Remo Grandori

"INTRODUCTIONDouble Shield TBMs were introduced in the market in the early seventies with three main targets:• Increase the TBM performances in term of advance per day thanks to the ability to erect a segmental lining simultaneously with the excavation phase.• Be able to advance through unstable and disturbed rocks under the protection of the shields• Provide a finished tunnel by installing a precast lining as the TBM advance.In 2003 SELI developed the design of the Double Shield Universal (DSU) TBM as an evolution of the original Double Shield TBM design.This new TBM design was targeted to improve: the TBM capability to advance through squeezing/converging rock formations under high cover, the telescopic joint design (allowing by such to operate the machine in double shield mode in very weak rock), the capability of the TBM to investigate and treat the ground around and ahead of the tunnel face.In the same lapse of time Single Shield TBMs, originally utilized for soft ground tunnelling, extended progressively their range of application to mix rocks and finally to hard rock tunnelling with increasing performances.This also thanks to the substantial reduction in the installation time of the segmental lining ring that contributed to minimize the TBM stand by time between two consecutive boring strokes.Today the choice between the two types of TBMs needs to be carefully evaluated project by project since one type of TBM may “prevail” in certain geologies and diameters and vice versa.THE VISHNUGAD PIPALKOTI TUNNELThe Vishnugad Pipalkoti Tunnel is part of the 444 MW Vishnugad Pipalkoti Hydro Electric Project (VPHEP) on Alaknanda river in Uttarakhand (India).The Owner is the Indian electric company “Tehry Hydro Development Corporation” (THDC) and the World Bank finances the project.The Headrace Tunnel total length is 13.4 Km and a section of about 12,3km will be excavated by TBM by SELI Overseas (Italy) in subcontract to HCC (India) the General Contractor for the project. The TBM will be delivered ex workshop in March 2016 and it is foreseen to start boring in the second half of 2016.Figure 1 below shows the location of the project and the following Table 1 summarizes the geometrical characteristics of the TBM tunnel."

Jan 1, 2016

By Peter J. Tarkoy

The art of predicting rock excavating machine performance has become increasingly detailed and refined. Researchers using laboratory experiments and machine manufacturers using field observations have identified and defined mechanisms of failure, rock and tool interaction, and relevant design principles affecting them. Concurrently, practitioners have developed index tests which reflect rock properties relevant to machine performance. Empirical relationships between index properties and machine performance (penetration rate, cutter consumption, and machine utilization) have been established from past experience and are currently used throughout the industry. Contractors have used such relationships for estimating throughout the world. The detail in which geological, geotechnical, test, and project data, empirical relationships, and construction experience are utilized, is limited by time constraints imposed by the bidding period. To fully utilize all available data, methods of analysis, and construction experience, a simple computer program was developed for a microcomputer costing less than $7500. As a result, 1. machine performance predictions are detailed & reliable, 2. construction alternatives may be examined, 3. anticipated conditions & performance are graphically, documented & easily comparable to those encountered, and 4. results include a listing of assumptions & results of performance analyses & a graphic performance summary.

Jan 1, 1979