Search Documents

By J. Kou

In this paper the activation behavior of quartz using Ca(OH)2 as an activator in quartz reverse flotation with anionic collector was evaluated and their adsorption behavior was investigated using a variety of techniques. The adsorption of the collector KS-I on the surface of quartz with and without Ca2+ was primarily characterized using Quartz Crystal Microbalance with Dissipation technique (QCM-D), which is a high sensitivity in-situ surface characterization technique. The flotation performance was evaluated using a laboratory mechanical flotation cell at different process parameters such as pH, collector dosage, and Ca(OH)2 dosage. The anionic collector evaluated was a commercial fatty acid KS-I. The QCM-D data showed that the collector adsorbed on quartz more readily with Ca2+ as activator. The mass and structural property of the collector layer adsorbed on quartz surface at 2.16×10-3 mol/L of Ca2+, 0.3 g/L of collector and pH 12.0 have been studied using the technique of QCM-D. The chemisorption of the collector KS-I on the surface of quartz in presence of Ca2+ were also demonstrated by means of zeta potential, QCM-D and FTIR analysis.

Feb 23, 2014

By Shailendra Chawla, Ashok Jaiswal, Sonu

Side spalling/skin failure occurs due to the high-induced stress in underground structures. In such cases, rock bolting or other support systems are being used to control the skin failure or spalling of the pillar. The nature of these support systems is passive, which acts during the deformation. These support systems restrict the displacement considerably of the side/or roof surface of the excavation. Ultimately, it improves the stability of the structure because of the increment in residual strength of rock mass. It is noted that these passive support systems give very low confinement in the range of 0–0.015 MPa at the onset of failure. As the level of confinement will be very low and dependent with progress of failure, triaxial test was not found practically suitable. Thus, an alternative procedure of testing has been proposed. In the procedure, sides of sample have been restricted little bit by using adhesive tape. It provides the limited boundness on the lateral direction (LBLD) of rock specimen. The uniaxial compression strength (UCS) test has been performed on 30 numbers of cylindrical rock specimens using the servo-controlled stiff testing machine. Specifically, two rock types (medium-coarse–grained and coarse-grained rocks) were studied in terms of stress–strain behaviour so that a full residual strength envelope for each specimen was obtained. This study reveals that the residual strength of limited confined rock specimens has been significantly increased as compared to unconfined rock for both groups of rock types. The average residual strength of LBLD specimens of fine-grained rock and medium coarse-grained rock has been increased around 12 times, and five times as compared to unconfined rock, respectively. The average peak strength of LBLD rock specimens has been increased in the range of 30.5 to 48.6% for coarse-grained rock. The results of this study have been presented in terms of peak strength, residual strength and Young’s modulus of rock, and the post-peak failure behaviour of rock specimens was also critically analysed through a stress–strain curve.

Mar 21, 2024

By J. B. Offei, K. Awuah-Offei

Mining companies registered with the SEC were required to comply with Regulation S-K 1300 for their annual report covering the first fiscal year ending on or after January 1, 2021. Consequently, most mining registrants filed their first S-K 1300 compliant disclosures in 2022. The US Securities & Exchange Commission (SEC), as part of its disclosure review program, has been issuing comment letters in response to these filings. This paper presents an overview of the trends in these comment letters. The authors reviewed comment letters retrieved from the SEC’s EDGAR database based on Standard Industrial Classification (SIC) Codes that cover mining, the content of the comment letter (whether it references S-K 1300 or not), the names of SEC staff listed in the comment letters, and other criteria. The analysis shows the SEC staff's reviews have been comprehensive covering the breadth of S-K 1300 and eliciting compliance with the rule. The staff through their comments are eliciting all the disclosures required by S-K 1300 and are not allowing registrants to substitute disclosures based on other standards for S-K 1300 disclosures. It is important, however, not to over generalize as the comments are based on the particular context.

Feb 1, 2023

By Roy A. Grancher

CYCLING WITH CEMENT "THE WHEEL IS COME FULL CIRCLE" Shakespeare's King Lear Act V, Scene 3, Line 176 The time clock of the cement industry has been turned back to the early 1950s. After the trials and tribulations of the decade of the Sixties, the hands now stand where they did just over twenty years ago. Cement shipments have steadily increased, with a record 419 million barrel level (78.8 million tons) being reached last year. Plants are operating at average utilization rates in excess of 85 percent of rated capacity. The spread between supply and demand has narrowed to where a definite shortage of cement now exists within the industry. The notable and unfortunate difference between the two periods however is that, back then, cement's returns were a respectable 14 to 18 percent, whereas today they stand at less than half those levels. Insufficient return forms the present foundation of the U.S. cement industry. This lack is destined to have a cumulative effect. Just as the industry's balance between supply and demand is returning to favorable proportions, promising a period that has historically and now should generate those profit levels required to modernize and provide for capacity addition, cement instead finds itself frozen by federal price controls into the semi-depressed condition that has existed for over a decade and from which it was just starting to emerge. Capital is not attracted to continued low returns, and increasingly restrictive pollution control measures are necessitating great non-productive expenditures be made as definite costs to stay in business. Even a clouded crystal ball would reveal that additional cement plant closings can be expected.

Jan 1, 1972

By A. J. Basu

A prototype expert system for planning and designing underground coal mines has been developed in a doctoral study (Basu, 1991) at the University of Kentucky (U.K.). The objective of the study was to provide a design tool for configuring layout parameters, production systems, and for determining economic feasibility. Details of knowledge engineering and the prototype knowledge-based system for integrated and intelligent planning and design have been covered in the dissertation. The prototype demonstrates its robustness by allowing interaction among major design components, most notably among ventilation, ground control, and production planning. A plan for testing and evaluating the prototype, an important phase of software development, is presented here. Existing evaluation procedures for expert system prototypes are discussed and the evaluations for the underground coal mine design expert system prototype are included. The initial testing plan used senior-level mining engineering students to test the acceptance of the prototype. This test suggested the usefulness of such a system for training and instruction. This initial acceptance test was performed with the feasibility prototype. The other test objective, i.e., testing the model's accuracy, involved extensive participation of domain experts. For overall accuracy evaluation, an existing underground coal mine design was compared with the output from a design session using the expert system prototype. The testing procedure is not an isolated, independent development phase. Much of the accuracy evaluation is done at the time of knowledge base development. Therefore, the knowledgebase itself does not need a formal test phase. The major purpose of the field testing is to determine probable user acceptance. The acceptance test determines the completeness of the prototype and also will determine efficiency of user interfaces.

Jan 1, 1992

By Robert W. Bartlett

Both hydrometallurgical and vapometallurgical processes often involve ores that have been previously ground and size classified. When the valuable mineral is substantially liberated, the chemical reaction is likely to occur on the particle surface and the particle core will shrink as the reaction proceeds. If the chemical reaction products are solid materials then a solid shell, usually porous, will form around the shrinking core. This is known as the core/shell or topochemical reaction model. Using a spherical approximation for the particles, equations have been developed to express the extent of chemical conversion of the particle, depending on which one of the following process or mass transport steps is rate controlling:1 (1) chemical reaction at the particle surface, (2) diffusion through the thickening reaction product shell or (3) mass transport through a boundary layer surrounding the particle. In a previous paper2 these equations were coupled with the Gates -Gaudin-Schuhmann equation 3 4 describing the distribution of particle sizes resulting from comminution of rocks and other brittle solids to develop reaction yield curves expressing the weight fraction of metal or other valuable component of the feed that was chemically converted as a function of residence time. This was done for (a) batch, (b) continuous plug flow and (c) continuous back-mix flow (continuous stirred tank) reactors or process vessels. To make the curves of general rather than special utility, the residence time (average residence time for back-mix reactors) was normalized to a dimensionless time by dividing by the time required to completely chemically convert the largest particle in the feed to reac-

Jan 1, 1972

By Richard R. Klimpel

INTRODUCTION The purpose of this paper is to summarize the current status of reagents used in the mineral industry plus present some current challenges and possible new technologies of the future. Table 1 lists the important families of reagents which, when taken together, constitute at least 95% of the current commercial reagent market. A very approximate estimate of the free world reagent market size in mineral applications is about 1.5 to 2.0 billion dollars (U.S.) using 1985 data. Obviously, to serve such a large market requires the effort of many different types of commercial supply sources. It is estimated that there are over 300 industrial firms in the free world that have a dedicated business/technical structure for supplying reagents related to the mining industry. There are a number of characteristics which are associated with the product families listed in Table 1. Understanding these characteristics helps to provide a realistic economic/technical basis for outlining future challenges in mining chemicals. 1.Essentially all of the products listed are old chemistry in the sense that the molecules have been known and manufactured for at least 25 years. This has not been a highly dynamic field of endeavor from the viewpoint of new product introduction. 2. The greater majority of the products listed can be viewed in commercial terms as "commodity" chemicals, that is, they are available from many sources and the pricing of a some- what generic product generally dominates differences in product quality or uniqueness. With commodity pricing, reagent suppliers significantly reduce research expenditures, loosen product quality somewhat if the applications of the reagents allow, etc. in order to be cost competitive.

Jan 1, 1989

By H. Y. Sohn

The paper discusses two processes, flash ironmaking technology (FIT) and moving-bed ironmaking technology (MBIT), which aim to reduce energy consumption and greenhouse gas emissions in the ironmaking industry by using concentrate directly without pelletizing and without using coke.

Aug 1, 2023

By Leonard B. Rothfeld

For many years, pulverized coal (PC) boilers in utility power plants have been the dominant market for domestic coal. Today, two new coal utilization technologies challenge the PC boiler's dominance. Atmospheric fluidized bed combustion (AFBC) and "coal gasification/combined cycle" (GCC) stand on the verge of commercial demonstration in the utility environment at a scale of 100 MW. Developed over the past decade, these technologies respond to the demands for cleaner ways to burn coal and for more flexibility in fuel supply. In the near term, these are the "clean coal" technologies most likely to have a significant impact, because they are ready for commercial application. As for environmental acceptability, consider that just a few years ago one of the environmental slogans was "no coal in California." Indeed, the only large quantities of coal above ground in California at that time were in transit on the way to Asia. Today, thanks to new technology, we can point to two operational coal-burning plants in California and one in the works: * Cool Water GCC demonstration plant (100 MW) * California Portland Cement AFBC commercial cogeneration, near Riverside (190 000 lb/hr steam) * Energy Factors AFBC commercial cogeneration at Stockton, to be operational 1988 (44 MW)

Jan 1, 1987

By J. Hoover

Real growth in the economy, increasing demand for electricity, and consumer stockpiling for a possible United Mineworkers of America (UMW) strike in October made 1984 a banner year for coal. Production and consumption climbed to record heights. Precautionary purchases brought inventories close to the peak levels of early 1981 when coal miners walked out for 72 days. Production slowed in the fourth quarter after labor and management concluded negotiations without a walkout. But output in every major coal producing state showed significant gains during the year US coal production totaled 807 Mt (890 million st) in 1984. This is a 13.8% increase over 1983 output. Lower production rates, principally in Appalachia, and sustained demand in the final quarter put downward pressure on coal stocks by the end of the year. Demand All market sectors experienced greater requirements for coal in 1984. Electric utility coal consumption increased 6.3%; exports climbed 4.8%; coke plants consumed 18.9% more coal; coal requirements in the other industrial sector expanded by 11.8%; and consumption in the residential/commercial sector rose 8.1%. Domestic consumption of coal reached a record 718 Mt (791 million st) in 1984. This is a 7.4% gain over the previous consumption high of 668 Mt (737 million st) in 1983. Electric Utilities The 4.6% increase in electric power generation in 1984 was coupled with expanding coal use relative to other energy sources. This resulted in a 6.3% rise in coal consumption, totaling 603 Mt (664 million st) for the year. Thirty-eight of 45 states where coal-fired electric power plants were operating shared in the 36-Mt (39 million-st) increase in electric utility coal consumption

Jan 5, 1985

By J. A. Herbst, Y. C. Lo

This paper attempts to answer whether or not the mill performance at Bougainville could have, in fact, been predicted by the population balance approach, or whether other special considerations are required to explain their behavior. In recent studies, the plant tests were performed at Bougainville and batch tests were carried out at the Utah Comminution Center. In all tests power measurements were made and several levels of energy input to grinding were evaluated. Also, tracer tests were performed for mill residence time determination. The performance of Bougainville's 5.5x6.4-m mill has been very successfully predicted by population balance methods. The prediction errors are only about 1% on product size distribution and 4% on power with a mill volume scale-up of 3790:1. It is significant that this approach will reduce the risk of failure in large mill design that has been recognized in traditional methods.

Jan 1, 1987

By K. L. Bickel

Catalyzed diesel particulate filters (CDPFs) are used for reducing diesel particulate matter (DPM) concentrations in underground mines. The U.S. Bureau of Mines is conducting research on how catalyzed diesel particulate filters perform. Two CDPFs, with two different catalysts, are used on vehicles in two mines. The CDPFs are periodically removed from service and evaluated in the laboratory to determine their DPM collection efficiency, regeneration temperature, and effects on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions. This report summarizes the results of the laboratory evaluation, and the mines' experience with the CDPFs. Both CDPFs have operated over 2,000 h. One was evaluated after 1,646 h; its collection efficiency at one operating condition was 87.3 pct. After 2,135 h of operation it was removed from service because it was damaged. The second CDPF continues to be used after 2,328 h of service. The laboratory evaluation indicated its collection efficiency decreased after 1,584 h of use and its regeneration temperature increased from 405' C to 420' C. The mines' experiences with the two CDPFs varied. While being used on mine vehicles, both CDPFs became plugged with DPM on a number of occasions because of insufficient regeneration. CDPFs are capable of lowering DPM concentrations in diesel exhaust. They can also lower emissions of CO and HC, depending on the type of catalyst used. In this study, the performance of the CDPFs changed with use. Recommendations are given in this report for proper use of CDPFs in mines.

Jan 1, 1994

By W. H. Jang

Recent research has demonstrated the utility of the FTIRIIRS adsorption density equation for in-situ study of surfactant adsorption phenomena at the surfaces of reactive internal reflection elements (IREs). The FTIR/IRS adsorption density equation is given by (formula) where r is the adsorption density, A/N is the absorbance per reflection, e is the integrated molar absorptivity, 4 is the bulk concentration of the surfactant, d. is the effective thickness, and dP is the depth of penetration. Previously, the validity of the adsorption density equation had been confirmed only from solution depletion measurements with high surface area powders. Now, FTIR/IRS studies of Langmuir-Blodgett (LB) monolayer films of fatty acid transferred to the surface of a calcium fluorite IRE .clearly validate the reliability of the FTIR/IRS adsorption density equation for quantitative analysis of surfactant adsorption. In addition, it was confirmed from the observed absorption band at 1550 cm-1 that the first monolayer of the transferred fatty acid chemisorbs at the surface of fluorite.

Jan 1, 1994

By Regina N. Tempel, Mae S. Gustin, Mark A. Engle

This study characterizes the hydrogeochemistry of groundwaters near opalite-hosted epithermal hot-spring type mercury deposits in the Ivanhoe mining district, Elko County, Nevada. Local groundwaters generally range from Ca-HCO3 to Ca-Mg-Na-SO4 type waters with background mercury concentrations ranging from 0.014 to 0.32 ug/l. Leaching experiments conducted on mineralized rocks, using typical water chemistries to represent local groundwaters, yield total mercury concentrations ranging from 6.3 ug/l to 27.4 ug/l after one year of reaction. Geochemical modeling indicates dissolved mercury is dominated by HgO(,) and that precipitation of quicksilver controls mercury concentrations to an upper limit of 63 ug/l.

Jan 1, 2000

By T. A. Farr, I. A. Gibbs, F. Guevara, S. R. Simms, G. Nojima

This paper describes an installation of a medium-voltage adjustable frequency motor drive (AFD) on a high starting torque regrinding mill. This type of application is typically found in the mineral industry dealing with hard ore. The AFD electrical architecture is introduced from line to load. The type of closed loop encoder feedback motor control algorithm is briefly described. The results of the AFD motor identification auto-tuning are compared against the manufacturer’s supplied data. The motor drive performance results are shown for pre-ramp DC fluxing, high starting torque with overload current, excessive load torque stall condition, and blocked rotor. The instrumentation and arrangement for the two watt-meter method to capture low frequency data are presented. The data shown is from the input power quality meter, the AFD computer tool, the output motor protection relay, an oscilloscope, and load shaft connected strain gauge (rotating telemetry for torque assessment). These types of high starting torque constant torque loads are found in mining and process industry applications employing AC adjustable frequency drives. Using field results should help demystify the use of voltage matching output transformers in AFD applications including constant torque loads

Mar 2, 2022

By Richard A. Bideaux

During 1977 and 1978, a comprehensive study was made of the drill-hole data obtained by Urangesellschaft, USA, from their Juniper Ridge, WY, uranium deposits. This included uranium grade data acquisition, application of a variety of mineral deposit modeling techniques, and estimates of minable reserves, which pointed towards a possible production decision.

Jan 1, 1979

By Rajendra K. Devala, Sukumar Bandopadhyay

In order to be able to design an adequate mine ventilation system it is necessary to understand how pollutant masses disperse into turbulent ventilation air streams. The mixing of gases and dusts with ventilating air, and dispersion of these pollutants in mine airways, are important flow or transfer problems. For the solution of such problems, the finite difference technique is often used. In this paper, numerical approximation schemes for the solution of the mass transfer problem have been developed using several explicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments using the concept of Root Mean Square error. The comparison of various schemes reveals that the explicit finite difference schemes analyzed here give more accurate results at lower velocities, though the results are dependent on the spatial and time steps considered. At higher velocities the schemes tends to oscillate about the analytical solution. INTRODUCTION In mining, most of the mine air pollutants, such as respirable dust, methane, blasting fumes and diesel exhaust, are produced at the mine face and in haulageways. Injection of any of these pollutants in the mine ventilating air causes disturbances of the equilibrium state of the pollutant concentration of the ventilating air. The mixing of these gases and dusts with the ventilating air are typical examples of mass transfer processes. Pollutants are diluted by the stream of ventilating air flow along airways and discharged into the outside atmosphere of the mine through a return shaft. The dispersions of these pollutants in mine airways are important flow or transfer problems. Knowledge about pollutant sources, emission and transport of these pollutants are essential for ventilation planning and design to ensure good engineering control over air quality, quantity, and environmental conditions. Modeling of mass transfer phenomena in mine ventilation is largely based on extensive studies of turbulent dispersion in wind tunnels and the lower atmosphere of the earth. The general approach in the formulation of models lies in the recognition that these mass transfer phenomena can be conceptualized as a flow problem that can be solved by the general application of Taylor's theory (1954) of turbulent flow and diffusion with modification appropriate static and dynamic parameters. If the face zone is initially contaminated by a pollutant over a long section (e.g. instantaneous exposure of large gas accumulation, rapid methane release etc.), the process of decontaminating the mine workings can be regarded as displacement and diffusion of the tailing edge of the cloud of contaminates in the form of a semi-infinite gas body, for which a one-dimensional mass transfer equation is represented by: [at + u • ax = Ex ex2 + f (x,t)(1.1)] In Eq. (1.1), the term [~~] is the rate of growth of the concentration in the differential element, while a [(5xx )] is the net gain of material due to convective transfer. The two terms balance the total loss of material due to turbulent dispersion that is represented by [Ex . 21] and f(x,t), the source term for the pollutant in the roadway. Several cases of mass transfer that occur in mining can be identified and modelled using the conservative volume element method. The governing equation, along with the associated boundary and initial conditions, source terms and their solutions are detailed elsewhere (Bandopadhyay and Ramani, 1988, Devala, 1989). Only one mass transfer situation is presented (Figure 1) here for the present analysis. Mixed Evolution of Pollutant (multiple pulses) Typical examples of these situations are emission of pollutants from multiple diesel vehicles in the face area, and gas emission from standing pillars as well as from broken coal seam during coal cutting with a continuous miner. The mathematical statement of the problem along with the initial and boundary conditions are given below, Governing Equation: [do+u- =E d2c(1.2) ataxx dx2] Initial conditions:

Jan 1, 1993

By P. Lopez, E. Wellman, N. Risso, A. Anani

Current machine learning models used for roof fall hazard prediction are mounted on expensive sensors, computationally expensive, or lack the robustness for accurate prediction in the underground mining environment. This research aims to provide a design methodology for a robust, low-cost, deep learning-based algorithm for underground mine roof fall hazard prediction. A data sampling plan is developed to ensure the replicability and robustness of the developed model. In addition, feature engineering and transformation methods are described to identify relevant features for hazard identification. The methodology described here will be used in model development, tested, and implemented as a real-time mobile device application. The new tool will be expected to detect roof fall hazards in real-time and contribute to a crowdsourcing approach for underground hazard detection.

Feb 1, 2023

By Gary A. Almeraris, Thomas F. Peyton

This paper chronicles the mining of a main interceptor sewer through a residential neighborhood for the MWRA's Boston Harbor clean-up. The Wellesley Extension Sewer Tunnel consisted of 490 m (1600 ft) of rock tunnel, 107 m (35V ft) of mixed face and 336 m (1100 ft) of softground. The tunnel was located 4.6 m (15 ft) below water table and passed directly beneath six buildings with as little as 7 m (23 ft) of cover. In addition, the tunnel ran parallel to and within 4.6 m (15 ft) of an existing sewer tunnel with flows up to 187,5 million liters (50 million gal.) per day. The rock encountered by the tunnel was comprised of gramodiorite, amphibilite and diabase. The soils which passed through the tunnel face consisted of tills, sands and non-cohesive plastic silts. The techniques developed and the equipment utilized to successfully mine this complicated ground are described.

Jan 1, 1991

By Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

Ground deformations are of major concern during tunneling, especially in downtown environments, since they have a significant impact on the costs and practicality of tunneling. This case history describes soil and groundwater conditions and ground behavior during the construction of twin transit tunnels for the Downtown Seattle Transit Project (DSTP). The tunnels were excavated through complex glacial soils ranging from hard glaciomarine drift to flowing sand. The tunneling process was greatly facilitated by the prediction of soil layer positions to an accuracy of ±0.6 m (2 ft). Tunneling was complicated by the presence of over 500 temporary tiebacks and by disturbed ground overlying an operating railroad tunnel. A variety of ground improvement techniques were used to successfully minimize settlements, which ranged from 1 cm (0.4 in.) in glaciomarine drift to 6 cm (2.4 in.) in flowing sands. Ground improvement techniques included compaction grouting, chemical grouting, jet grouting, and eductor well systems.

Jan 1, 1991