Search Documents

By B. Valentim

The methodology used to obtain fly ash subsamples of different sizes is generally based on wet or dry sieving methods. However, the worth of such methods is not certain if the methodology applied is not mentioned in the analytical procedure. After performing a fly ash mechanical dry sieving, the authors compared those results with the ones obtained by laser diffraction on the same samples and found unacceptable discrepancies. A preliminary study of a wet sieving analysis carried out on an economizer fly ash sample showed that this method was more effective than the dry sieving. The importance of standardizing the way samples are handled, pretreated and presented to the instrument of analysis are suggested and interlaboratory reproducibility trials are needed to create a common standard methodology to obtain large amounts of fly ash size fraction subsamples.

Jan 1, 2008

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By Fredrick Fränding

In mining and quarrying operations, electric motors can fail for a variety of reasons. Some failures are directly linked to demanding production requirements and contaminant-laden environments and, consequently, are difficult to prevent. A sizeable number, however, are caused by ?offline? factors that have nothing to do with production. These include inadequate or substandard motor repair practices and improper motor shipping, storage and installation. The fact that failures are at times attributable to repair- or rebuild-related errors and problems raises the stakes when selecting an electric motor repair provider. Teaming with high-quality electric motor shops can help a company reduce failures due to offline factors, improving motor reliability and cutting downtime costs. Regardless of location or annual revenues, the best motor shops have similar business cultures and share many of the same characteristics.

Jan 1, 2009

By Sabina Brady

Investment in the ferrous sector between 1981 and 1985 will total about $9 billion, or 7.6% of the state budget for capital assets. The money will primarily go to complete the first stage of the Baoshan Iron and Steel complex and to increase steel production by 3 Mt* (3.3 million st) and seamless tubing by 0.5 Mt (551,000 st). Investment in 1983 will be about $3.5 billion, a 28% increase over 1981. Although data on nonferrous investment is less specific, the Chinese announced early this spring that the country's investment would be 2.6 times greater than the average spent during the previous five year plans. Geological surveying will also be stepped up. The Ministry of Geology and Minerals recently announced it will incorporate a search for metal and mineral resources into its second round of oil and gas surveys. The Sixth Five-Year Plan desig¬nates some actual production targets. Steel is to increase to more than 72 Mt (79.4 million st). The country's production of 10 priority nonferrous metals - aluminum (and bauxite), copper, lead, zinc, nickel, tin, antimony, mercury, magnesium, and titanium - is to increase 12.7%. Top priority is to develop aluminum production. Renewed efforts are to be made to develop gold and silver production and to increase rare earth and rare metal production. By April 1983 when the China Nonferrous Metal Industry Corp. was established, some five months after publication of the Five-Year Plan, the goals for nonferrous development had already been upgraded and changed to include: • development priority status equal to that of coal's; • an increase of more than 150% in the 1985 projected production level for the 10 top nonferrous metals (a move from the Sixth Five-year Plan's production increase of 12.7% to one of 34%); and • modification of the top 10 nonferrous metals list to include tungsten, molybdenum, and rare earths. Aluminum, copper, lead, and zinc maintained primary importance, while mercury, magnesium, and titanium were deleted. It is likely that the modification will be taken one step further and titanium will be substituted for antimony. China has already indicated its intentions to stabilize rather than expand its antimony industry, while press reports play up the titanium industry's importance to the country's development. In addition, the China Nonferrous Metal Industry Corp. announced that it expects to register a progressive annual increase of 4% in foreign currency earnings through export. China's nonferrous development efforts, therefore, appear two-pronged. First, the country's efforts will be directed toward self-sufficiency in its four major process and primary metals - aluminum, copper, zinc, and lead - and a number of other nonferrous metals that are in increasing demand by its light industry sector. At present, 96% of China's non¬ferrous consumption is composed of aluminum, copper, lead, and zinc. Substantial portions of that must be imported to meet rising demand. Second, efforts will concentrate on those metals that can be developed the fastest and are in "urgent demand" on the international market. Metals such as tungsten, tin, molybdenum, titanium, nickel, and rare earths will be given freer use of foreign capital and technology to increase production levels and raise quality. Examples of some projects in the area include upgrading the country's carbide industry and developing new high speed and tool steels to meet international standards. Foreign involvement and sales have been reported in each area, particularly with regard to sales of deposition equipment and presses by Swiss and West Ger-

Jan 8, 1983

By Paul C. Schmall, Thomas Tuozzolo, Arthur B. Corwin

The Lenox Avenue Reconstruction Project involved the excavation and replacement of 750 m (2,500 ft) of deteriorated subway invert concrete, 5 to 7 m (15 to20 ft) below water table in very permeable ground. The Replacement work was done over an 8 month period, while maintaining track service through this subway section. The project was dewatered with a single 125 l/s (2,000 gpm) wellpoint system,750 m (2,500 ft) in length, which was installed from inside the active tunnel structure and configured to coexist in the subway tunnel with operating trains as well as the construction activities. A thin diaphragm jet grout wall was utilized on one end of the site to cut off the flow of water across a difficult geological interface that was situated immediately below the tunnel invert. The thin diaphragm jet grout wall permitted the large 116th Street Station area to be dewatered completely with well points from outside of the excavation.

Jan 1, 2001

By Marco Sonnenschein

As time is costly, engineering companies have developed methods, procedures and mechanical equipment to tunnel faster. But the best excavation method will not be able to cope with the time pressure if there is not a reliable backup system. Therefore, the application of belt conveyors for tunnel boring machine (TBM) drives as well as for drill-and-blast driven tunnels assure a quick and smooth removal of excavated soil in order to enhance the efficiency of the tunneling equipment. During the last 10 years, belt conveyor systems have achieved ?state-of-the-art? levels and have become the first choice for muck removal systems in both TBM and drill-and-blast driven tunnels. Because time has become such a key criterion in tunneling projects, it is essential that all equipment is operated so as to derive optimum efficiency and minimize costs. Efficiency also means to think about new tasks for existing technologies.

Jan 1, 2012

By John Sleavin

As part of the Link Light Rail project in Seattle, WA, work was completed at the Pine Street Stub Tunnel (PSST) in early 2007 for the Central Link project. This tunnel was excavated using cut-and-cover construction within the limits of Pine Street. The stub tunnel provides a turn back via double crossover for light rail trains running in the Downtown Transit Tunnel (DTT), as well as a connection point for the next phase of the project, the University Link (Fig. 1). Designing the new University Link tunnel connection to the existing PSST was a tricky task. The on-site geotechnical conditions, buried obstructions, geometry, requirements for construction and balancing operational considerations and neighborhood stakeholder concerns associated with the recently completed PSST combined to create a uniquely challenging assignment.

Jan 1, 2010

By Norbert Patzelt, Johann Knecht

Future ore reserves of major gold producers in North America and elsewhere will consist of refractory gold ores. About 60 % of the current U.S. gold production is mined in Nevada. Several of the large gold operations in this state indicate that 40 to 90 % of their future ore feeds will contain refractory gold. To com­pound problems, average head grades for refractory U.S. gold ores had fallen from 8 - 9 g/mt to about 4 g/mt by 1991. In Latin America, 52 % of the gold operations will require milling for optimal recovery. Deeper reserves are, like in North America, refractory. Therefore a special treatment process is needed in order to allow for the gold ore to be leached downstream in a conven­tional cyanidation process for a high gold recovery. There are several options available for this oxidation process like treat­ment of the gold bearing ore in pressure oxidation, in a biooxi­dation or in a roasting plant depending on the reason for the refractoriness. If organic carbonaceous matters and sulfides are the prima­ry reasons for the refractoriness, whole ore roasting is a pre­ferred method for the treatment of this type of ore. Since dry ore is to feed to the roaster, a dry grinding mill is advantageous. For the dry grinding system, the moisture content and the ore char­acteristic is of importance. Those parameters decide the mode of the grinding system. For autoclave systems common wet grind­ing systems can be applied. This paper deals with technical aspects for dry grinding plants and gives an outlook on and pos­sibilities for new grinding systems.

Jan 1, 1996

By MOHAMMAD R. H. GORAKHKI, Christopher A. Bareither, MANUEL APARICIO, Joseph Scalia IV

The focus of this study was on the evaluation of hydrologic and environmental behavior observed in GeoWaste and waste rock test piles. GeoWaste is a mixture of fast-filtered tailings and waste rock prepared as a tailings-dominated mixture. The two test piles included potentially acid-generating (PAG) waste rock and were operated for 26 months to evaluate whether GeoWaste can suppresses sulfide oxidation and production of metal-rich acid mine drainage relative to PAG waste rock. The test piles were constructed in the shape of truncated 5-m-tall pyramids with 25-m base sides and flat 5-m × 5-m top surfaces. Water content, temperature, electrical conductivity, and oxygen concentration were monitored in four layers and at five locations within each layer in both test piles. In addition, 5-m × 5-m lysimeters were installed at the base of each pile to collect leachate. Approximately 2660 mm of water was added to the surfaces of the test piles via precipitation and irrigation (irrigation ≈ 1050 mm applied at an approximately constant rate for 70 days). The measured saturation, oxygen concentration, electrical conductivity, and temperature in the GeoWaste and waste rock piles suggest more sulfide oxidation occurred in the waste rock pile compared to the GeoWaste pile. Observations from the pile experiments suggest that co-managing mine waste in the form of GeoWaste reduced acid generation compared to waste rock alone due to the lower permeability and unsaturated state of the GeoWaste pile that reduced downward migration of moisture and inhibited drainage.

Mar 31, 2021

By Jupneek Singh, Zachary A. Kiehl, Leila Safazadeh, Gareth Kennedy, Eleonora Widzyk-Capehart, Jeremy W. Ward

Mine workers are continuously exposed to a host of nonfatal stressors and potentially fatal hazards: noise exposure, excessive vibration, poor air quality, toxicant exposure, ignition of combustible gases, equipment-related accidents, and thermal heat stress. Wearable or portable sensors and contextual analytics provide a platform to unobtrusively collect and fuse multimodal health and safety data in real time to compute both acute safety and longitudinal health insights. This paper presents preliminary trial results, conducted by Simtars, VigiLife, Inc., and Queensland Mines Rescue Service, of the application of wearable sensors to monitor heat stress and other vital biometrics for mines rescue personnel.

Feb 1, 2024

By K. J. Stanaway

Major world ilmenite and rutile accumulations reveal similar regional geology and Proterozoic age deeper crustal source rocks. During crustal collision titanium crystallizes as ilmenite and rutile at buried sites of high pressure and temperature rock metamorphism. Hydrothermal activity can convert titanium minerals to rutile, but titanium migration and enrichment seem only local. Many melts crystallize rocks with iron-titanium oxides in solid solution, but titanium enrichment at economic scale takes place in basic intrusive melts often associated with anorthosites and charnokite. Sedimentary placer enrichments have formed since the Proterozoic with water-resistant ilmenite, and rutile segregating by gravity from quartz sands deposited from flowing water. Placers have residual, alluvial, strand and shallow marine variants. Time, organic acids, and sand permeability play lead roles in the leaching of iron from ilmenite during weathering and diagenesis.

Jan 1, 2005

By Gordon Cook

American Electric Power Company (AEP operates 31 coal mines in three states, and some 26 electric generating stations (19 coal-fired) located in the Ohio River Basin. Normally the system burns over 36,071,600 tonnes (40,000,000 tons) of coal and generates in excess of 3.6 X 1018 J (100 billion kwh) of electricity per year. In 1975, AEP, in response to the progressively more stringent air quality requirements of the clean air act, acquired large low-sulfur reserves in Carbon County, Utah (Figure 1. Location Map). Price River Coal Company (PRCC) is the operator OF this multi-seam complex, which is part of the Book Cliffs coalfield at an elevation exceeding 1,829 m (6,000 ft.). The topography is mountainous and divided by numerous canyons. Flat areas are at a premium (Figure 2. Castle Gate Area). Modern high production longwall mining takes in some top and bottom waste, and in this particular operation, it amounts to about 14% of the ROM tonnage.

Jan 1, 1983

By D. L. Petersen, C. R. Nelson, B. K. Nelson, B. D. Wagener

The Lafayette Bluff tunnel, currently under construction for the Minnesota Department of Transportation (MnDOT), will be among the widest highway tunnels in the United States. The 199-meter tunnel is being constructed in a closely jointed, variably weathered diabase rock mass. Cover above the tunnel crown ranges from 4 meters to 27 meters, and is less than the tunnel excavated width of 18.3 meters for about 60 percent of its length. These factors dictated special support and lining design, limitations on excavation sizes and required sequences for support installation. Tunnel excavation is by controlled blasting, with multiple top headings and bench. Rock support and lining consists of external portal beams, rockbolts and reinforced shotcrete. A final concrete lining provides structural support for the rock mass and the membrane waterproofing system.

Jan 1, 1991

By K. Whysner

The recycling of metal resources in mining influenced water (MIW) requires a paradigm shift from within the mine water treatment industry. The potential to recover zinc for beneficial use in the micronutrient fertilizer industry was investigated through a survey of zinc micronutrient fertilizer representatives. An application of the findings to a case study of the Argo Tunnel influent MIW was then implemented. It was concluded that the potential to beneficially reuse MIW residuals in fertilizers exists; the current process sequences of treatment will need to be modified if metal recycling is to be prioritized.

Feb 27, 2013

By Wang Hongwei, Wu Yongping, Cao Peipei, Jiao Jianqiang

Fully mechanized top caving mining of steeply inclined extra-thick seams with variable angles has complex roof rock movement, failure, caving, and filling mechanisms. Moreover, the variable-angle coal seams make rock–equipment stability control challenging. We analyzed rock deformation and failure mechanisms, overburden bearing structures, and working characteristics of supports through physical simulations, field tests, and theoretical analysis of the no. 120210 working face of Zaoquan Coal Mine. Overburden rock movement has distinct regional characteristics, with a large caving height (to the main roof layer) in the upper area, and lower caving height (to the lower main roof) in the lower area. Support loading is regional and unbalanced along the inclined direction. The critical layer of overlying strata migrates, and bearing structures formed by breaking the critical layer exhibit cross-layer generalization along the inclination. The upper region has a cantilever beam structure in the basic roof rock layer; the lower region has an inclined masonry structure with multistage ladders in the breakage basic roof rock layer. Application of a false-inclined working face layout with the tailgate ahead of the headgate and an arc arrangement (radius 28.65 m, arc length 10–20 m) in variable angle areas, and regional control of support working resistance and top-coal caving amounts, control regional failure overburden. Safe and efficient mining was achieved, with the monthly production and recovery rates reaching 344,900 t and 85.86%, respectively. Our results expand the scope of fully mechanized top caving mining and have important theoretical and technological significance.

Nov 23, 2020

By Mark N. Savit

It is indeed a rarity for a non-engineer, let alone a lawyer, to even be considered for a mining-related award, especially where that award is for significant contributions to technical progress in the mining and exploration sectors. So, when I was notified that I had received this award, I struggled for a topic that would meld the legal world that I operate in with the engineering driven world of exploration and extraction. The most exciting part of my job has always been the opportunity to absorb the technical details of the cases I work on and, in effect, translate them for a lay audience. Too often, I have found, lawyers, judges, legislators and yes, even regulators who lack a technical background simply give up trying to understand the details of the very conditions or processes that they are trying to describe and simply repeat phrases told to them by their client or by a retained expert.

Jan 1, 2008

By Rong Lu, Hao Wu, Bing Dai, Guoyan Zhao, Li Cheng, Weizhang Liang

Affected by the disturbance of blasting activities, deformation instability and rock dynamic disasters are prone to occur in deep hard rock roadways. Thus, it is particularly necessary to understand the failure behavior of rocks and roadways under dynamic loads. In this study, a series of impact loading tests were carried out on sandstone samples with and without a circular cavity by a modified split Hopkinson pressure bar (SHPB) test system. The mechanical properties and energy evolution of the samples were systematically investigated, and the effect of cavity size was analyzed. The results showed that the presence of the cavity in the samples weakens the dynamic compressive strength by more than 10%, and the peak strain and brittleness are also reduced to varying degrees. Under dynamic loading, spalling cracks occur first on the roof and floor of the cavity, and then different numbers of shear cracks are formed on the sample diagonals. The eventual shear failure mode is the result of the connection of the shear cracks and the cavity. As the cavity radius increases, the dissipated energy density and fractal dimension both grow accordingly, leading to smaller and smaller rock fragments. The dynamic failure behavior of the circular cavity can be well explained based on the dynamic stress distribution law. Overall, this study can provide a reference for the study of the mechanism of rock burst in deep roadways.

Feb 18, 2021

By William R. Yernberg

The early part of the decade was marked by world-wide problems and economic difficulties. In 1980, President Jimmy Carter ordered the failed military mission to rescue hostages in the U.S. Embassy in Iran, Mt. Saint Helens, WA erupted killing 60 people and the Soviets and Mujaheddin guerrillas clashed in Afghanistan after the Soviet invasion. Later in the year, Ronald Reagan was elected president, defeating Carter. The first launch of a space shuttle (Columbia) occurred in 1981. Also in 1981, the first IBM-PC’s begin to roll off the lines. In 1982, Argentina invaded the Falkland Islands and Mexico’s economy was in collapse. In 1980, the U.S. unemployment rate stood at 7.1 percent, and by 1982 the rate increased to 9.7 percent. 1980 marked SME’s first full year in its new office building in Littleton, CO. The new facility was dedicated in November 1979. Claude L. Crowley was executive director of SME in 1980 and remained in that position throughout the decade. SME’s membership stood at about 26,000 throughout this period (1980-1982).

Jan 1, 2007

By James F. Kvitkovich, George V. Weisdack

Editor’s note: This is the second part of a two-part series on longwall mining in the United States. Part one was published in the December 2005 issue of ME (pp. 21-26). It provided a history of longwall coal mining in the United States. It also discussed the technology involved in the productivity gains and operational improvements. Boyd anticipates that U.S. coal production will increase by 61 Mt (67 million st) (6 percent) from 2004 to 2010. A combination of higher surface and underground mine production will be required to meet the projected market demand. Boyd’s projections of coal production by major mining methods are shown in Table 1.

Jan 1, 2006

By M. Okido, W. Wei, L. Chai

The kinetics on the growth of Thiobacillus ferrooxidans was studied by use of series piezoelectric quartz crystal ( SPQC ). Arsenic ioninhibits the growth of Thiobacillus ferrooxidans, which is consistent with the previous results by other measuring method. This further demonstrates that the SPQC can monitor the chemical activity of the growth of Thiobacillus ferrooxidans. Cupric ion accelerates the growth of Thiobacillus ferrooxidans. The mechanism was discussed, it was considered that copper promotes the protein enzyme of Thiobacillus ferrooxidans, rustic yanin, to form over the range of cupric ion concentration studied. There action order of cupric ion in accelerating the bacterial growth is 0.067. The growth of Thiobacillus ferrooxidans is dependent on temperature, the apparent reaction activation energy decreases from25.56 kJ / mol to 18.32 kJ / mol because of the addition of 10 mg / L Cu(II) to the bacterial growth solution of pH 2.0 at initial inoculum of 10%.

Jan 1, 2000