Search Documents

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The study proposes a dynamic path planning method for mining equipment based on spatial kinematics and real-time correction of coal-rock state identification. The method integrates real geological data and equipment operation information to improve the autonomous cutting of fully mechanized mining equipment.

May 1, 2023

By R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corporation's Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about -502 without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1971

By R. D. Lopez

The concept of "heat recuperation" for the grate-kiln pelletizing system was first implemented at the Sydvaranger plant in Norway in 1974. Essentially, heat recuperation involves bringing hot air from the second stage of the pellet cooler to the drying zone to increase drying-air temperature to the maximum limit. 'Burner-fuel savings result from a lower kiln secondary-air mass flow at a higher temperature. Because of the fuel benefits achieved at Sydvaranger, heat recuperation has been included innumerous new grate-kiln plants built since then, and some older plants have been retrofitted for heat recuperation. In recent years there has been much confusion about the fuel benefits of heat recuperation. To answer some of the questions, a mathematical model was developed and plant tests were conducted at Minntac Phase 111. Minntac is a magnetite taconite concentrating and pelletizing plant, and Phase III has two indurating lines. This paper presents the results of the studies and plant tests.

Jan 1, 1980

By V. Gall

The three-dimensional finite element technique combined with the progressive failure approach was utilized to simulate stress distributions in a mine section which occur in response to a longwall mining operation. Due to the availability of the Cray supercomputer, a large-scale three-dimensional finite element model was developed for the analysis. The Hoek-Brown failure criterion, which describes a realistic behavior of rock masses, was used for the simulation of progressive failure. A comparison of calculated and monitored stresses in the mine has shown that the model gives a good representation of stresses in the mine structure.

Jan 1, 1990

By Verya Nasri, James Sullivan, Alex Varas

"INTRODUCTION Many major cities in the United States have a combined storm water and sanitary sewer network. Regular rainfall overwhelms the system capacity and results in millions of cubic meters of untreated sewage being dumped into local waterways. One legally mandated solution includes several kilometers of large diameter shallow or deep rock or soil tunnels, a pump station as well as associated collection sewers, diversion structures and drop shafts. In this paper, the basis for design of different system elements including the drop shafts and pump station is explained in detail. Common construction methods used for different type of shafts including tangential vortex and baffle plunge, and also pump station alternatives comprising cavern or various shaft configurations are discussed. DIFFERENT TYPES OF PUMP STATIONS The dewatering pump station serves as the heart of any deep CSO tunnel system and is critical to the goal of reducing CSOs by providing a controlled release of the stored tunnel volume to the wastewater treatment plant. As the major mechanical component of the project, the station will require the greatest attention by operations and maintenance staff. Designing a durable and easily operated pump station requires addressing some major challenges, including the following: • Longevity – equipment, materials of construction, and station environment • Controlling odors • Safety for operators and maintenance personnel • Easy access to equipment • Protection from hydraulic surges Location. Owners face a fundamental decision relative to the location of the pump station, which will affect how these challenges are addressed. The pump station can be built within the tunnel launch shaft or within its own dedicated shaft. This decision is driven by cost and schedule. Use of the tunnel launch shaft may provide owners cost saving opportunities by not having to construct a separate pump station shaft. However, this will likely extend the pump station construction as much as two years until the tunneling has been completed. Furthermore, delays to the tunneling operation would delay the pump station construction work, potentially leading to delay claims. For this reason, it has been more common to utilize a separate pump station shaft on recent CSO tunnel projects (Nasri et al. 2015)."

Jan 1, 2016

By B. C. Haydon

Manganese silver ores are well known to be refractory towards cyanidation. Various processes have been suggested for improving the amenability of these ores. A sulfurous acid pre-leach is one such process. This paper traces the development and implementation of the sulfurous acid pre-leach process for the retreatment of manganese silver tailings at Tonopah, Nevada. An account of the test work program is presented, followed by a description of the operating plant and specimen metallurgical performance. The paper also summarizes the history of the Tonopah tailings, their mineralogy and makes reference to previous application of the sulfurous acid pre-leach process.

Jan 1, 1984

By S. Cotten

The concept for a Mine Escape Vehicle (MEV) is motivated by the desire to enable personnel to evacuate a mine rapidly as the first and most desirable response to any underground emergency. Under a NIOSH contract, Raytheon UTD developed a conceptual design for a vehicle that coal miners could use to facilitate their rapid exit from an underground coal mine in the case of emergency, including fire or explosion. The vehicle requirements include the capacity to provide life support functions for a number of miners, operate in an oxygen deficient, low or no visibility atmosphere, and travel at speeds faster than miners can walk out of the mine. To develop the MEV concept, three primary tasks were identified and executed. The first task focused on developing a realistic concept of operations (CONOPS) and associated high level vehicle requirements. The second task identified and evaluated currently available equipment and technologies that could be applied to address the CONOPS. The final task developed a design concept that integrated the identified components for the five (5) MEV sub-systems to provide the foundation for future detailed engineering design and prototype construction. The resulting MEV design concept is centered upon retrofitting existing mine personnel carrier chasses with available, mine-worthy equipment capable of addressing the MEV requirements. This approach offers a practical and economic avenue to prototype development and delivery with minimum lead-time and risk. Furthermore, by integrating familiar and available equipment into the design and CONOPS, the resulting Mine Escape Vehicles should also be more readily accepted by the mining industry.

Jan 1, 2010

By B. W. Cavender

Innovative mining and metallurgical operating techniques or processes can be identified and developed by systematically analyzing change as it occurs within the mine, plant, technology, or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions, and the development of new knowledge. Innovation can be effectively organized, practiced, and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically-designed policies regarding organizational structure and staffing, daily management practices, and compensation and incentives.

Jan 1, 1994

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

To provide critical scientific data and engineering guidelines to federal and state regulatory agencies as well as the coal and gas industries, the National Institute for Occupational Safety and Health (NIOSH) initiated a Gas Well Stability Research Program in 2016. This paper summarizes the critical scientific data acquisition, interpretation, and modeling by NIOSH regarding the stability of unconventional shale gas wells influenced by longwall mining. Currently, NIOSH is the only organization in the U.S. conducting such fundamental and impactoriented research, which receives input and collaborations from MSHA, PADEP, WVDMS, OHDNR, the coal industry, and the gas industry. Results from the NIOSH field instrumentation programs—which include surface, subsurface, and underground instrumentation—and the parallel three-dimensional numerical modeling programs indicate that, under shallow and medium covers, the measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Casing couplers are found to play an important role in longwall-induced casing deformations. Cementing alternatives are found to have significant impact on longwall-induced casing stresses and deformations. Measured 60-arm caliper logging results are in good agreement with three-dimensional computer simulation results. Engineering guidelines on longwall-induced deformations, casing and cementing alternatives, gas well setback distances, as well as risk assessment strategy are proposed.

Mar 2, 2022

By Joseph Cervik

The mined coal bed and surrounding strata are both sources of methane which must be control led during mining. During developmental mining, the mined coalbed is the primary methane source; during retreat longwall mining, the primary methane source is the overlying strata. Underground technology is being developed to control both sources. This technology involves drilling long horizontal drainage holes into the mined coal bed and relatively short holes (less than 152 m or 500 feet) into the overlying strata. Because of the large volumes of methane that flow from such drainage holes and the limited ventilation available for in-mine dilution, underground pipelines are used to transport the drained gas to the surface. Large- scale in-mine degasification demonstrations showed reductions in methane flow of up to 70% during developmental mining.

Jan 1, 1981

By S. P. Mehrotra

In this review article, various approaches and mathematical models that have been used to simulate, design, and synthesize flotation circuits are examined. First, a brief review of flotation kinetics is presented which is followed by a discussion on simulation of flotation circuits. The existing literature on optimal design of flotation circuits has been divided into two broad categories. In the first category, a generalized integral approach is used wherein the optimal circuit design involves determination of both optimal interconnection of various flotation cells/ banks of cells in terms of structural parameters and optimal values of various operating parameters. In the second category, a conventional circuit configuration is assumed to be the best configuration; the optimal design here only means the optimization of operating parameters. The merits and demerits of these two approaches are discussed.

Jan 1, 1987

The value of US industrial mineral output last year was $20 billion, a 12% decline from 1981. A glance at the accompanying table and a review of the comments made by several contributors reveals how poorly many industrial minerals fared during 1982. Bromine and peat posted a 6% increase in production while recovered sulfur showed only a 3% gain over 1981. Pumice, salt, and dimension stone managed to stay more or less even with 1981 production. However, most industrial minerals posted losses for the year from 3% for vermiculite, sodium carbonate, and gypsum to 49% for ilmenite. Naturally, the depressed economy is to blame for decreased production and consumption. Low steel and auto production, lower housing starts, and many other factors impacted the industrial mineral industries. Hopefully the worst is over. Interest rates are down, energy costs are decreasing, the automobile and housing industries show signs of picking up. Perhaps the 1983 annual review will be less gloomy. Many thanks to these industrial minerals technical committee members for their contribution to this year's annual review: G. S. Austin, E. S. Montgomery, H. P. Ehrlinger III, D. B. Jorgensen, R. L. Parratt, J. F. Burst, W. Mallory, N. C. Trivedi, and N. K. Olson.

Jan 5, 1983

By W. G. Fischer

Trona ore at the Westvaco mine of FMC Corporation has been obtained by room- and-pillar methods since the mine began operation. The flat-lying, 10-foot bed of trona, Na2CO3 NaHCO3 2H2O, is covered by 1500 feet of weak shale and sandstone. Extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early 60's forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans' were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. Roof cones troy in the longwall methods appeared to be more satisfactory than that found in room-and--pillar techniques. It was therefore felt that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 1, 1966

By A. B. Cecala

An evaluation was recently performed on a district recirculation system at a trona mine in Granger, Wyoming. A 1.52m (5 ft) diameter, 37.3kw (50 hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated approximately 31.4 m'/sec (66,578 ft'/min) of air back into the intake. This amounted to a recirculation factor of approximately 20 pct of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 6l0m (2,000 ft) and 1,829m (6,000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane, and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF. tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1991

By J. C. Squire, E. W. Baker, G. A. Sullivan, G. W. Flathers

A mine collapse severs communication with trapped miners. Landlines are crushed and commercially available radios cannot penetrate hundreds of feet of dense, conductive earth without the use of regenerative repeaters that may also be crushed. This paper describes a proof-of-concept device that uses seismic P-waves, instead of radio waves, to allow communication of a code that represents prearranged messages, including the safe haven location identifier, number of people and air quality, from trapped miners to aboveground rescue units. The transmitter designed is about 0.03 m3 (1 ft3) in size and can broadcast for four hours from its 27-kg (60-lb) battery pack. The receiver consists of a geophone and a 2.5-kg (5.5- lb) signal conditioning unit attached to a laptop computer, which displays the communication signal in real time. Testing in a bituminous coal mine with an MSHA representative revealed the device was able to transmit through 271 m (890 ft) of overburden, at 0° and 12° from vertical, using 500 W of power.

Jan 1, 2009

By J. R. Allan

Loki Gold Corporation of Vancouver, B.C. is developing the Brewery Creek Mine, an open pit heap leach gold mine, 55 km East of Dawson City in Yukon, Canada. Mineable reserves are 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797 000 oz) of gold. Ore processing will employ a cyanide heap leach using run of mine ore. Permitting this mine has drawn significant attention because the heap leach technology, while proven in other jurisdictions, has not been used in Yukon. Engineering design of the heap leach was similar to that for heaps in more temperate climates, with the added issues of permafrost and cold weather operations. Solution balance with seasonal placement of ore and year -round leaching requires very large pond capacity for spring thaw conditions.

Jan 1, 1996

By R. J. Hickson

The giant El Abra copper mine project under development in Northern Chile will come on stream in early 1997 at a production rate of 500 million pounds of cathode copper annually. Ownership is 51 % Cyprus Amax and 49% Codelco. Cyprus Amax has construction responsibility. Total project cost is $1050 million. El Abra will incorporate latest operational technology with labor efficient practices to achieve world class productivity levels and low initial cash costs of about US $0.35/lb copper. Development procedures for the almost 800 million ton oxide deposit, as well as the hydrometallurgical processes selected for recovery of the copper values are discussed. Construction costs and pertinent technical data are shown.

Jan 1, 1996

By R. Gray

"Experience from Australia has identified what is referred to as non-conventional surface subsidence behaviour. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence”, and far-field horizontal movements – even occurring beyond conventional “angle of draw” limits. This paper discusses such behaviour recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900ft to the north, mining at depths of 330 – 720ft. Investigations (including a subsequent ground movement monitoring program) found a range of evidence in the vicinity suggesting that valley closure and far-field horizontal movements may have occurred resulting from the adjacent mining. The paper discusses the phenomenon of non-conventional subsidence behaviour and the Ryerson State Park case study, including an assessment of mining, geology and subsidence impacts and suggested ground behavioural mechanisms. INTRODUCTION Non-Conventional Subsidence The conventional understanding of coal mine subsidence on which most current subsidence understanding and prediction techniques are based, includes the concept of angle of draw which effectively limits the lateral extent of subsidence effects and impacts. Within this zone – above and marginally beyond the boundary of mining – downward vertical subsidence is the dominant component, together with localised horizontal movements towards the mined region, with related tilts and strains. However, more recent experience from Australia over the last two or three decades has identified what is referred to as non-conventional surface subsidence behaviour. This is found to occur in areas of irregular surface topography or variable terrain, and is characterised by phenomena such as valley closure, valley floor uplift or upsidence, and far-field horizontal movements, all of which can occur beyond the conventional angle of draw limits. NSW Department of Planning (2008) defined the conditions for both conventional and non-conventional subsidence behaviour as follows: “The conventional or general model of surface subsidence, which finds worldwide acceptance, is based on assuming the following site conditions:"

Jan 1, 2015

By R. R. Beebe

Marcona Corporation produces about 3.5 million long tons of iron ore pellets annually on its two travelling grate pelletizing machines at San Nicolas, Peru. During 1969, these pellets will be shipped to customers in four marketing areas--Japan, the United States, Europe, and South America. All of these sales are on the open market, and product quality is a major concern. Typical chemical, structural, and quality test results for Marcona pellets are given in Table 1. [ ]

Jan 1, 1969

By Michael J. Friedel

The permeability and flow capacity in unsaturated media is investigated by the Bureau of Mines for application to in situ copper leach mining at the Cyprus Casa Grande mine site. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through rubblization. By producing a maximum block diameter of 4 m, injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 1991