Search Documents

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By David S. Young

All pigments and extenders or fillers whether organic or inorganic fall into the following broad general classes: I. Colored II.-White III. Black IV. Metallic A pigment- is any particulate matter that is essentially insoluble and chemically unaffected by the media into which it is dispersed. According to this very broad definition, colored pigments, white pigments, fillers, extenders, and functional pigments would all be included. The particulate size range would also be quite broad ranging from very fine colloidal particles (~0.01µ) to relatively coarse particles (~100.0µ). This broad definition is usually subdivided into more practical divisions which tend to relate the classification of the pigment to its primary function in the system in which it is used. Hence, the word extender implies that its major purpose may be to extend the system.

Jan 1, 1985

By K. Chandrasekaran

Carbon-in-leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. The CIL process is becoming attractive even in other situations when preg robbing is not a factor. This article discusses the situations in which the CIL circuit can be applied. The results of leach-carbon-in-pulp (CIP) and CIL circuits at Newmont Gold's Mill No. 2, No. 4 and No. 5 are presented for comparison: Mill No. 4 was initially designed for a throughput of 4.1 kt/d (4500 stpd). It is presently operating at an average throughput of 6.6 kt/d (7300 stpd) without significant changes to the original design. The design considerations of the Mill No. 4 CIL circuit are discussed. The design of any processing facility represents a series of decisions. The final design options should ultimately be resolved based on economic as well as technical considerations. Every design decision represents some sort of compromise. From the designer's view point, these decisions are made with the conviction that the final product represents the most prudent long-term expenditure. The design throughput rate is a decision reflecting a maximum return for the capital and operating costs that the plant will incur over the life of the mineral resource. The result is a plant that is not operator proof or maintenance free because it would be too costly to build. At some point, the incremental increase in the level of capital expenditure would not adequately compensate for the lower

Jan 1, 1991

By G. R. Hart

The expected 1990 Clean Air legislation is providing electric utilities with a series of challenges and decisions as the utilities prepare strategies to comply with the resulting regulations. This paper addresses the strategy development of a coal-based utility --the legislation, the process used, the fuel issues, the options available, and the decisions to be made.

Jan 1, 1991

By J. O. Marsden, J. H. Gourdie, J. R. Arnold, J. G. Mansanti

During the testing and design of the Gold Fields' Chimney Creek mine, it was found that a much higher carbon loading was possible with CIC (carbon-in-solution columns) than with CIP (carbon-in-pulp). In an effort to keep the carbon handling minimized, an emphasis was put on forcing gold to the CIC circuit rather than the CIP. After considerable study, it was found that a circuit with two thickeners and an interstage leach would force 90% of the gold to CIC. Computer modelling indicates that the benefits of the hybrid circuit include higher recovery, less carbon handling, fewer leach tanks, and lower reagent costs.

Jan 1, 1990

By Ralph E. Weeks

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1988

By J. R. Klaehn, M. Shi, T. E. Lister, L. A. Diaz, J. S. McNally

Since 2019, approximately two dozen international battery recycling companies have been operating at the commercial or pilot scale [1]. However, current process capacity does not exceed 100,000 tons of end-of-life (EOL) lithium-ion batteries (LIB) per year, and the current recycling rate is only about 5% in North America [2-3]. Recycling metals from EOL LIBs is not only essential to waste minimization and environmental stewardship, but also a source of critical materials, which can contribute towards supply chain stabilization. LIB recycling can be roughly divided into three categories: direct recycling, pyrometallurgy, and hydrometallurgy. Direct recycling seeks to retain as much of the manufactured effort with minimum chemical processing [4]. The evolution of battery designs and chemical compositions are challenges to this approach [5-6]. Pyrometallurgical processes are robust and flexible allowing a broad spectrum of batteries with minimum pre-processing requirements. Some of the matrix issues are solved through combustion of some constituents. Smelting is strongly tied to fossil energy and air emissions are a concern. In addition, pyrometallurgical processes are not stand alone, as hydrometallurgical refining normally required to separate and recover the metals of interest (Co, Ni, and Cu) from the produced alloy and Li from the slag [7]. Hydrometallurgical processes can be highly selective and efficient in recovering high purity materials [8]. In general, hydrometallurgical processes are considered cleaner and less costly than high temperature processes [4,9-10]. Extensive chemical consumption and waste generation significantly increase the operating costs and overall environmental impact of the hydrometallurgical processes [11]. Leaching of metals from LIBs is dominated by the mixture of sulfuric acid (1 to 4 M H2SO4) and hydrogen peroxide (1 to 15 wt.% H2O2) [10]. Although organic acids have been tested as lower environmental impact alternatives, the reported pulp density operations are low < 60 g/L [10-11]. For the H2SO4/H2O2 leachates, high leaching efficiencies >90% are reported for Co, Ni, Mn, and Li from cathode materials at temperatures over 40 ⁰C and pulp densities between 30 to 200 g/L [9-10]. H2O2 acts as reducing agent to convert Co+3 and Mn+4 into their soluble forms, Co+2 and Mn+2 [12]. Despite the claims of H2O2 being a clean reducing agent [13], production of H2O2 has significant environmental impacts as determined by life-cycle analyses [13-14]. Moreover, the costs and risks associated with H2O2 transportation and storage cannot be ignored [15].

Mar 2, 2022

By Glenn H. Damon

Concern about environmental pollution goes back many centuries, but until recently most efforts to control it have been perfunctory and spasmodic, aimed largely at coal smoke and other visible pollutants. Air pollution is to a large degree a byproduct of our economic development, and scientific knowledge of the causes and character of such pollution is more extensive than the technology to handle the waste byproducts of our industrial civilization. The removal of all constituents foreign to the air from the effluents produced by an industrialized society is obviously impractical at this time. There is widespread difference of opinion regarding acceptable ambient air concentration levels for the Various pollutants produced by combustion processes, but there is basic agreement that the pollution of the atmosphere must be controlled and eventually reduced. The magnitude of the air pollution problem has been increasing rapidly because our expanding economy calls for an ever-increasing consumption of energy, and fossil fuels are a principal source of energy. For example, the consumption of electricity has been increasing at an average annual rate of approximately 8 percent over the last 10 or 1.5 years. Table 1 shows the estimated emission of the principal pollutants into the atmosphere in 1966. The approximately 90 million automobiles, trucks, and buses on American highways contribute the largest proportion of pollutants to the atmosphere, but that fact does not alter the growing problems of the coal industry. You will note that sulfur oxides, particulates, and nitrogen oxides are all products of the combustion of coal. Of these air contaminants, sulfur oxides are now receiving major emphasis in terms of research to develop effective means for control, Table 2 shows that the combustion of coal produces approximately 60 percent of the sulfur oxides discharged to the atmosphere. While the utilization of coal is the principal source of particulate matter, this is not considered as serious a problem as it was in the early part of the century because of technological developments that have produced sound methods for the removal of particulates from waste gas streams.

Jan 1, 1968

By Hubert E. Risser

At the outset of a discussion on the adaptability of Illinois coals for use in iron and steel production, it is perhaps well to define terms. ?Adaptability? as used in this context, means that a coal can be, adapted to use within a given technological and economic framework. For a coal to be adaptable, to use in the manufacture of metallurgical coke within the present technological and economic framework, it must possess, among other things, at least the following characteristics: 1. The coal must be capable of producing, alone or in combination with other coals, a coke that can meet at least a minimum standard of required performance in the present-day blast furnace. The coke must have sufficient strength, stability, hardness, and freedom from impurities to make it suitable. 2. If the coal in its raw form does not meet these requirements, it must be amenable to beneficiation or upgrading so that the requirements can be met. 3. It must be available in uniform quality and in sufficient quantities to meet the need. 4. Use of the coal must be economically attractive. If its quality is equivalent; to that of the coals with which it must compete, it must be no more expensive than they. If It is better, a premium price may perhaps be demanded. If, in any respect, it is the least bit less suitable, the cost must be lower to offset its disadvantages.

Jan 1, 1961

By F. W. Schweitzer

The trend toward development of large low grade ore bodies has accelerated in recent years. It has been estimated within the copper industry that "porphyry" type deposits will provide the bulk of copper production during the next 30 years. It is further estimated that in these deposits the average ore grade by the year 2000 will be 0.25% copper (1). Many of the new porphyry copper discoveries are of such extremely low grade that they are particularly sensitive to small fluctuations in cost variables and copper prices. Because haulage constitutes a major item of surface mining expense, the capability to transport large tonnages of material at increasingly lower unit costs is vital to the profitable operation of many of these mines. High capacity conveyor belts appear to have considerable promise in this area. The heaviest use of high tonnage conveyors has been in the brown coal industry in Germany. In the past 20 years several such installations have proven successful. In addition to the German installations, several other successful systems have been put into operation. Some examples are: The Oroville Dam project in the United States; the tar sand operation in Northwest Canada; the pre-mine stripping and mining of the Twin Buttes Mine in the United States; the Kursk Magnetite &apos;dine in the U.S.S.R.; and the Nchanga Copper Mine in Zambia. Most of the systems mentioned are handling alluvial material consisting mainly of fines. The noteworthy point regarding these installations is their high continuous capacity. One of the largest lignite mines in the world is at Fortuna, Germany, where over 15,700 tons (15,250mt) per hour of overburden is transported on an 87 inch (221cm) wide belt running, at over 1000 feet (305m) per minute.(2). Another example is a 20,000 ton (18,150mt) per hour system for loading iron ore into barges on the Great Lakes (3).

Jan 1, 1976

By Roger N. Kust

Because ammonia can form complex ions with certain of the transition metals, such as copper and nickel, it has long been of interest to extractive metallurgists interested in leaching or separating these metals. Although it is a relatively expensive reagent, ammonia is amenable to recycle because of its volatility. In development of processes utilizing ammoniacal leaching or separation schemes, information regarding solution vapor pressures, pH and solubility limitations is needed. There is voluminous literature on ammonia-water systems generated by the urea industry. However, frequently the systems of interest to metallurgists differ significantly in concentrations of ammonia used, the temperatures of interest. Furthermore, the differences arising from the presence of metal values in solution must be comprehended. There is surprisingly little information readily available regarding systems of practical interest to metallurgy. As a result, those interested in ammonia-based processes end up either doing expensive laboratory research to obtain necessary data or overdesigning the process. Another approach to obtaining desired information about ammoniacal systems is to attempt to calculate from first principles the various solution properties. This paper is being presented to illustrate what can be accomplished by estimating the state of equilibrium in an ammoniacal carbonate system from available thermodynamic information making simplifying assumptions when needed.

Jan 1, 1976

By Lance Rasband, Richard Hanke, John Starcevich

"The world’s largest tunnel boring machine (TBM), at the time of her launch in 2012, the TBM locally referred to as “Bertha,” is incapacitated due to mechanical failure. Bertha’s stoppage places her 25m below the surface between the aged Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to access all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Due to the limited area above the tunnel alignment and physical constraints created by existing infrastructure, the dimensions of the otherwise symmetrical shaft are heavily impacted, thereby requiring special attention to design and layout. Consequently, the shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude. INTRODUCTION Mining on Seattle’s SR99 tunnel began in July of 2013. Initial mining progressed slowly through a 4.5 m thick fiber-reinforced concrete headwall before immediately entering the first of three planned safe havens. Once through the headwall and safe haven the machine would move through roughly 122 lineal meters of jet grout improved soil at a rate of slightly over 1.6 m per day. It was anticipated that once mining has passed through the improved area, “Bertha” – now the world’s 2nd largest tunnel boring machine (TBM), would be moving at a rate of almost 11 m per day. By the end of October 2013, Bertha had mined roughly 131 m, averaging 1.4 m per day, and had begun mining within native soils. By the start of December 2013, tunneling had reached the 244 m mark and Bertha was now averaging 3.6 m per day, achieving as much as 12.8 m of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt. Initial reports stated an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure within the ground around the TBM, to allow the contractor’s personnel to inspect the cutter head from within and also to investigate for the presence of obstructions at the face of the cutter head. During inspection, the contractor’s crews found fragments of steel pipe entangled in the cutter head. The steel was apparently from an abandoned 254 mm diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, she attempted to move forward but was only able to generate a slow crawl."

Jan 1, 2016

By P. Corser

Operational and geotechnical constraints on mining within steeply dipping deposits and historic landslide areas, which are characteristic of subarctic coal deposits in Alaska, will be discussed. The current plan for mining through these areas will be presented, as well as an alternative plan for minimizing the adverse effects of mining through an historic landslide area.

Jan 1, 1988

By J. B. Yianatos

This paper addresses the impact on performance of column height (H), and column height to diameter (H/D) ratio by modelling the effect of HID on mixing and consequently on recovery and grade. Mineral recovery increases with increasing H/D ratio for a constant column volume and feed flowrate, while the concentrate grade decreases to a minor extent. Columns 10-15m in height with H/D-10 are well suited for feed rates 150-600 L/min. Maximum H/D is determined by the gas carrying capacity, an important consideration for pilot units where H/D?200.

Jan 1, 1987

By Jayson Ripke, Peter Amelunxen, Brandon Akerstrom, Fernanda Solís

It is commonly known in the industry that one of the key challenges for a greenfield project, such as Capstone Copper’s Santo Domingo project, is the obtention of samples for metallurgical testing and subsequent plant design. To face this challenge, the Santo Domingo project completed 169,692 meters of drilling. The material collected has been used for a variety of analysis including the economic recovery of iron, which contributes significant economic value to the Santo Domingo business case. Composite and variability samples, covering the main geological units considered in the life of mine (LOM) plan, were selected for bench and pilot scale testwork. Davis Tube Tests, small scale Low Intensity Magnetic Separation (LIMS) tests and a pilot utilizing a 48 in (1.2 m), diameter magnetic separation drum were completed. The testwork demonstrated that the Santo Domingo ore could achieve iron concentrate grades of 65% Fe - suitable for blast furnace, and 67% Fe - suitable for Direct Reduction, primarily by concentration of magnetite. The outcomes of this work have informed the iron concentrator plant design and scale up.

Feb 1, 2025

By R. H. Church

The Bureau of Mines&apos; Tuscaloosa Research Center has developed a field test unit (FTU) which dewaters mine and/or mineral processing by-product slurries. The feed material (by-product slurry) is mixed with a known quantity and specific type of synthetic polymer (usually a polyacrylamide) to induce flocculation in a continuous operation. The flocculated material passes over a specific number and size of slotted stationary screens which separates the flocculated solid material from the "clean" water. The "static screens" are positioned at a fixed angle to maximize flow capacity and capture of the solids content. An investigation was conducted at an industrial crushed stone operation located near Birmingham, AL, to determine if the Bureau&apos;s FTU could successfully dewater the waste slurry generated during grinding and sizing operations at this facility. The investigation showed that waste slurries could be dewatered to 50 pct solids, at a polymer cost of approximately $0.85/ton of dry solids treated, and resulted in approximately 85 to 95 pct solids recovery. The dewatered material continued to consolidate and reached 69 pct solids in 24 h. Presently, the waste slurry generated at this facility is discarded into impoundments. However, this research has identified the recovered waste as an economically marketable product.

Jan 1, 1994

By J. C. Motz

During the past five years, Rexnord has developed, tested and introduced the Nordberg Omnicone Crusher to the industry. When the Symons brothers invented the cone crusher over 60 years ago, they employed the principle wherein the length of the crushing stroke was related to the free fall of material by gravity. This permitted the material being crushed to fall vertically in the crushing chamber; and in effect, caused the particles to be crushed in a series of steps or stages as the particles got smaller due to the crushing action. This also helps to reduce the rate of wear of the liners since the sliding motion of the particles is minimized.

Jan 1, 1986

By Crone Duncan

The search. for massive sulphide orebodies is steadily being extended to greater depths as well as expanding outward into the large portion of the earth&apos;s surface where the sulphide bodies are deeply weathered. Massive sulphide orebodies are generally not large in dimensions. They are not like disseminated type sulphide bodies that form large ground exploration targets that can be detected at greater and greater depths simply by increasing the geometrical spacing between the geophysical transmitter and receiver. In¬creasing the transmitter-receiver spacing with massive sulphide bodies eventually "waters down" the anomaly from the body until it disappears into noise. If high surface conductivity is present, as is common in areas of deep weathering, the problem is compounded by the increasing response of the surface layer, as the receiver-transmitter spacing is expanded. The search to greater depths has important implications other than just detection of the orebody. Drilling costs are increased and the probability of missing the target are increased. Missing an orebody is an expense that is difficult to evaluate in dollars per line mile of survey especially since one does not know the value of what was missed. A ground Pulse EM method has the capabilities of solving the problems of deeper exploration particularly in areas of surface weathering it can attain deep penetration without large coil spacings, it also provides information from a complete range of frequencies. The method has other operational advantages since it is free of geometrical restrictions as to coil alignments and can operate in areas of high power line noise.

Jan 1, 1975

By Patrick Browne

Drilling programs and the study of active geothermal systems have shown that the reservoir rocks in many fields contain minor quantities of base and precious metals. Commonly, base-metal sulfides occur in the subsurface but, where present, Au, Ag, Hg, As, T1 and Sb rich precipitates deposit near, or at, the surface. Although in some fields (Geysers, Larderello, Tongonan) some of the ore minerals (and others) are relict, there is evidence that they are now depositing in a few systems. Recent work on active hydrothermal systems in New Zealand shows that: (1) Sphalerite, galena, chalcopyrite (forming veins and disseminated discrete crystals) plus rare pentlandite, cobaltite and arsenopyrite, occur at Broadlands, NZ. Rare quantities of base-metal sulfides also occur in cores and cuttings from the geothermal fields of Waiotapu, Kawerau, Tauhara, and Ngawha. Further, Kakimoto (1983) has identified cassiterite, native silver, and trace gold in cores from Tauhara, in the south-eastern part of the Wairakei field. Bore temperatures at the depths from which these minerals were recovered are mostly between 220° and 300°C, but at Broadlands are locally as low as 120°C. The host rocks are Quaternary talc-alkali, silicic lavas and pyroclastic rocks, andesites, dacite and deep Mesozoic greywackes and argillites; however, there is no obvious relationship between mineralization and stratigraphy, permeability or well output. (2) The deposition of amorphous precious metal precipitates (Au, Ag, Hg, As, Sb, T1) from hot springs and well discharges has taken place at Broadlands, Waiotapu and Rotokawa; it also occurs at Kawerau. (3) Water discharging from Frying Pan Lake, Waimangu, is presently depositing siliceous sinter containing up to 4.1% tungsten. A characteristic of mineral-depositing fluids in the New Zealand geothermal fields is their very low salinity (total dissolved salts of 3000 ppm or less but with high CO2); they are of near- neutral alkali chloride composition, although water discharging from Frying Pan Lake has a pH of 4.5, and very low metal contents. Very effective concentration processes (10 times for gold at Broadlands) must occur: in the subsurface these include boiling and rapid cooling but near, and at, the surface, mixing of waters of different pH seems to dominate. In particular, descending acid condensate, derived from separated steam and oxidation of H2S mixes with its parent alkali chloride water, resulting in precipitation of amorphous ore metals. Base-metal sulfides also occur in veins and as disseminated grains in geothermal fields at Tongonan, Leyte and Southern Negros, Philippines. These fields have a porphyry-type setting with host rocks of Miocene andesitic lavas and pyroclastics intruded by diorites so that the fields have undergone complicated thermal histories before cooling to their present base temperatures of about 325°C. Precious metals have precipitated from waters from some wells (Leach, pers. comm.) but they do not, as yet, form ore-grade deposits.

Jan 1, 1984

By Hans G. Machel

In low-temperature diagenetic environments (0 c T c 60 - 80°C), elemental sulfur forms by six common processes: via (1) inorganic oxidation of H2S by molecular oxygen, (2) inorganic oxidation of H2S by ferric iron compounds, (3) polysulfide disproportion- ation; and via the microbial metabolic actions of (4) colorless sulfur bacteria, (5) colored sulfur bacteria, and (6) some types of thiobacilli. Economically viable deposits of native sulfur usually are formed by only one process: inorganic oxidation of H2S by molecular oxygen. The amount of elemental sulfur is also limited by three common processes that destroy it in low- temperature diagenetic environments: bacterial reduction, bacterial oxidation, and inorganic oxidation. In high-temperature diagenetic environments (80 - 10o°C c T c 150 - 200°C), particularly in sour gas reservoirs, there are seven common processes forming elemental sulfur: (1) SOdH2S reaction, (2) H2S- hydrocarbon reaction, (3) polysulfide disproportionation, (4) catalytic H2S decomposition, (5) C02-H2S reaction, (6) chlorinification, and (7) exsolution of physically dissolved elemental sulfur. Natural processes that destroy or remove elemental sulfur in such settings are hydrocarbon sulfurization, polysulfide formation, and advection. In most sour gas reservoirs, relatively small quantities of elemental sulfur occur as a free phase (solid or liquid). However, elemental sulfur often precipitates in copious amounts from the reservoir fluids via exsolution and polysulfide disproportionation during production of sour gas reservoirs. By extension, elemental sulfur may precipitate from reservoir fluids in relatively large quantities upon uplift and erosion of deep sour gas reservoirs, or from advection of sulfurous fluids into shallower settings via faults or other high-permeability pathways.

Jan 1, 1992