Search Documents

By Donald E. Zipperian

It has been recognized that froth flotation of mineral particles utilizing rising flow of micro size air bubbles, counter-current to quiescent falling flow of particles in a column type cell, provides a unique mechanical atmosphere conducive to extension of froth flotation process to much coarser and finer particles sizes than possible with mechanically agitated and aerated cells. 1,2,3,4. This paper describes metallurgical results obtained at several plant installations of large capacity commercial size Deister FLOTAIRE® Column Flotation Cells. These cells utilize air aspiration into surface tension lowered water to generate micro size bubbles. Operating costs, power, wear, and scaling characteristics of rougher, cleaner, and scavenger units are compared with mechanical units. Problems encountered and scale up criteria developed when increasing from 0.20m(8inch) diameter pilot cells to 2.42m(96inch) commercial cells are discussed.

Jan 1, 1985

By J. P. Rider

Along with increased production from longwall units has come the likelihood of increased worker noise exposures. In recent years, equipment has become larger, more powerful, and noisier than its predecessors. For these reasons, the Mining Division of the National Institute for Occupational Safety and Health (NIOSH) is investigating worker noise exposure on longwall faces and researching possible solutions to reduce this exposure. Part of this research effort involves studying the effect of covering the underside of longwall shields with acoustical material to reduce reverberating noise along the face. Experiments using acoustical absorptive insulation to cover the undersides of the shields, shearer body, and the shield supports were conducted at the full scale simulated longwall test facility located at the Pittsburgh Research Center. Sound levels were recorded every l.5 m [5 ft] along a 15.2 m [50 ft] section of the simulated face for all of the conditions tested. The analysis of the data indicated that a 2.0-3.0 dBA noise reduction was achieved between the shearer drums and a 4.0-5.5 dBA attenuation was attained upwind of the headgate drum.

Jan 1, 1997

By Jean-Marie Deschamps

In an approach to the complicated study of bauxite from Les Baux de Provence it is necessary to consider the paleogeographical context of all the bauxites in southern France. These bauxites are of Karstic type, belonging to a metallogenic area extending from the Pyrenees Mountains to the Alpine Massif. Within this area each deposit does not always correspond to the same geological period. There are differing opinions regarding the origin of Karstic-type bauxite and a discussion of these various theories is beyond the scope of this paper. Bauxite of Les Baux, in Provence, was discovered in 1821 by the chemist, Berthier, near this picturesque village located in the region of Arles. It is Les Baux from which the name of bauxite originates. For a long time this bauxite was of no interest because of high silica 'and mediocre alumina content. Besides, the calcium carbonate content is somewhat high and is one of the main characteristics of Les Baux bauxite. The problem of exploration of the Les Baux deposit has been to prospect minable zones according to traditional norms where silica and carbonate are low.

Jan 1, 1977

By D. Sinha

Mine investment decisions involve both objective and subjective criteria. The subjective criteria are efficiently decided by interaction with company experts. The Expert System approach can incorporate knowledge of experts and interact with conventional computer programs on mine evaluation. Artificial intelligence offers considerable opportunities in comprehensive mine investment decision making process.

Jan 1, 1998

By D. E. Walsh

The behaviour of gold particles on a spiral was studied using radioactive gold tracers. The method allowed the effect of particle size, particle shape, pulp density, feed rate, and splitter settings to be studied. Although the method has been successfully applied to other gravity concentrators, it was found that reliable results were more difficult to obtain on the spiral. However, these preliminary results show that provided suitable precautions are taken, the technique is capable of providing valuable information that cannot be obtained by conventional studies, and could be used to better optimize spiral performance.

Jan 1, 1992

By S. Dawson

The Republic of South Africa has become a major producer of opencast coal in recent years. Opencast production commenced in 1970 and by 1977 some 10 million run of mine tonnes were being produced annually, Since then surface mine activity has increased to more than 60 million tonnes which represents approximately one third of the total annual South African? coal production. Whilst a substantial portion of this production is exported, the majority is used in the domestic market, The largest consumer, being the South?\ African Electricity Commission (Eskom), produces most of South Africa's electricity using coal fired power stations,

Jan 1, 1990

By Brenda J. Wolfe

Following successful laboratory and pilot plant investigation of dewatering characteristics of molybdenum concentrate produced by a Chilean copper/moly producer, two (2) DENVER SALA 500 Series Tube Press Filters were installed in 1994 to handle the total production volume. Moisture requirements in the filter cake have been consistently met, eliminating the need for thermal drying after filtration. Operating data and Tube Press Filter are described herein.

Jan 1, 1995

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By Wilson Blake

The occurrence of rock bursts in some deep mines throughout the world constitutes a severe operational hazard. In addition to endangering the safety of the miners, the rock-burst problem is a major factor in mining economically in deep mines because of the loss of production and expense owing to cleanup and repairs following a burst. Developing means of controlling or eliminating rock bursts has been the subject of intensive research for over 50 years. While much has been learned about the effects of rock bursts, little is known about their basic causes; hence, control measures have been at best only partially effective--attested to by the number and severity of bursts that continue to occur throughout the world each year. In the Coeur d'Alene mining district of north Idaho, the rock-burst problem continues as the silver and lead veins persist at depth. These veins are presently being mined at greater than 7,000 feet below the surface and will be mined to some 10,000 feet in the future. The majority of rock bursts in this district occur in pillars. While pillar bursting has been essentially eliminated in some deep-mining districts by longwall techniques, modification or application of this technique to the thin, irregular, and near vertically dipping veins of the Coeur d'Alene district has not been found to be practical. The creation of pillars is a consequence of the horizontal cut and fill mining method used. Figure 1 shows a vertical longitudinal projection of the silver vein at the Galena mine, illustrating the mining method. Stoping progresses between raises and is carried upward between levels. A horizontal pillar is created as a stope approaches a mined-out level. Recent broad-band micro seismic monitoring of rock-burst-prone stopes by the Bureau of Mines has shown that potential burst zones could be delineated weeks in advance of a burst and that a definite sequence of events took place prior to the occurrence of a pillar burst (1). Hence, time was available for control measures to be effected when a stope pillar reached a critical burst geometry.

Jan 1, 1971

By S. C. Tadolini

The use of resin-grouted cable supports to control large ground movements in several types of underground mines has increased substantially since being introduced in 1991. Cables offer several advantages over traditional support systems, having large support capacities coupled with the flexibility to be used in low openings. Cable slings have been designed to be installed on-cycle using no-spin technology or a two-piece unit that can be placed with hand-held drilling equipment. Additionally, yielding cable supports have been developed and are being used to control large amounts of movement in coal and evaporite deposits.

Jan 1, 1998

By Mir Ahmad Mohammadi

Land uplift due to mine flooding has become a significant challenge with extensive historical mining activities, particularly in Germany’s Ruhr district. The cessation of coal mining operations has led to a gradual rise in groundwater levels, altering geotechnical and hydrological conditions and causing surface uplift. This study develops a system dynamics (SD) model to investigate the dynamic interactions of influential variables such as groundwater levels, total stress, porosity and permeability with land uplift over time. The model integrates causal loop diagrams (CLD) and stock flow diagrams (SFD) to comprehensively understand the system’s behavior. SFD illustrated that for a 10 percent increase in groundwater level, the land uplift increased by about +6 percent, and a rise of 200 percent in total stress caused an 18 percent increase in effective stress, which decreased the land uplift by about 20 percent. This study highlights the importance of dynamic modeling in informing land-use planning and mitigating the long-term impacts of land uplift after mine closures.

Mar 1, 2025

By L. Figueroa

Electrochemical methods have potential to treat waters impacted by mining, while simultaneously producing a recoverable metal product to off-set treatment costs. Mining-impacted waters may present challenges with electrochemical treatment due to low concentrations and complex solutions of numerous dissolved metals. This paper presents an evaluation of the potential strengths and limitations of abiotic electrowinning of mining-impacted waters. In particular the impacts of chemical composition on metals removal are evaluated. Results of bench-scale experiments demonstrate the potential to remove metals on the cathode (copper, cadmium, lead), as well as the anode (manganese). Pre-treatment for iron and aluminum may be needed and post-treatment pH adjustment would be necessary. INTRODUCTION Due to continually increasing demand for metals, new technologies and innovative applications of existing technologies are needed to recover metals from mining-impacted waters. Electrochemical methods have long been used for metallurgical processes with solutions containing high concentrations of the target metal. However, electrochemistry also has potential to treat waters with lower metal concentrations, while simultaneously producing a recoverable metal product to offset treatment costs. Electrochemical water treatment may have several benefits over traditional alkaline treatment for acid rock drainage (ARD). Sludge produced from alkaline treatment has high water content that is difficult to dewater, even for treatment plants producing a relatively high-density sludge. For example, the Argo Tunnel Water Treatment Facility (Argo Facility) in Idaho Springs, Colorado uses hydrated lime to produce a high-density sludge with a solids content of 20 to 25 percent and filter cake with solids content from 30 to 35 percent [1]. Furthermore, costs for managing the sludge are significant, approximately $90,000 per year for treating approximately 150 million gallons of water [1]. Although not the case for the Argo Facility, sludge produced from alkaline treatment of ARD has potential to be classified as hazardous. Disposal of sludge also opens up the potential for future liability depending on the sludge’s chemical stability and methods of disposal. In contrast to alkaline treatment, electrochemical treatment produces metals in elemental and other highly-dense forms on the cathode. If metals concentrations and flow rates are sufficiently high, the metals recovered may help offset overall treatment costs. In addition, sludge production would be reduced, if not eliminated altogether, thereby reducing both disposal costs and potential future liabilities as well.

Jan 1, 2019

By C. G. Janes, N. Finkelstein, L. M. Jr. Johnson

In May, 1966, the General Services Administration (GSA) announced a program to encourage additional domestic production of copper in the interest of national security. Upon learning of the copper production expansion program, Duval Corporation entered into negotiations with GSA for development of the Sierrita copper-molybdenum property under the program. Agreements between the GSA and Duval Sierrita Corporation, a wholly owned subsidiary of Duval Corporation, were concluded in 1967, with the Sierrita Concentrator beginning operation in 1970 at a designed capacity of 72,000 STPD. Subsequent additions and modifications have expanded capacity to 90,000 STPD. This property, located approximately 20 miles south of Tucson, Arizona, represents an investment including working capital of about $200 million. These funds were provided from an $83 million loan from GSA, repayable in copper valued at 38 cents per pound, $48.75 million of bank loans subject to U. S. Government V- loan guarantees, and Company capital contributions. Current general operating statistics for the concentrator are listed below: Ore Grade 0.32% Cu., 0.030% Mo. Daily Tons Milled 90,000 STPD Annual Copper Production 94,600 Tons Annual Molybdenum Production 15,000,000 Lbs. Annual Silver Production 1,135,000 Ounces

Jan 1, 1976

By W. Dan Hausel

Archean supracrustal rocks of the South Pass greenstone belt of western Wyoming have been an important source of gold and iron ore. Actual gold production statistics are incom- plete although gold production estimates for the South Pass- Atlantic City district range from a low of 2.0 Mg (70,000 oz) (Koschmann and Bergendal, 1968) to a high of 9.8 Mg (327,000 oz) (Hausel, 1980). From 1962 to 1983 iron ore was also mined from the greenstone belt and production totaled more than 91 Mt (90 million It). The supracrustal rocks of the South Pass greenstone belt occur in a tightly folded synform bounded by Late Archean granite and granodiorite. The youngest of the Archean successions has a reported Rb-Sr isochron age of 2.8 b.y. (Stuckess, et al., 1985). Metamorphism of the supracrustals increases towards the flanks of the belt and is amphibolite-grade enclosing a small island of greenschist facies rocks. The supracrustal sequence consists of metasedimentary and metaigneous rocks that are divisible into four mappable units. The metasediments include metagraywacke, quartzite, pelitic schist, banded iron formation, metaconglomerate, and graphitic schist. Metavolcanics include metabasalt, meta-andesite, and ultramafic schist. These supracrustals have been intruded by mafic sills and dikes and tonalitic stocks and dikes. Two granite plutons and associated pegmatites intrude the supracrustals in the western portion of the belt, and the supracrustals exhibit both fault and intrusive contacts with granitic batholiths along the western and eastern margins. The northeastern flank of the Archean belt is unconformably over- lain by Paleozoic sediments, and the southern portion of the belt is onlaped by Tertiary sediments.

Jan 1, 1990

By C. A. Young

Previous experimental results have shown that an increase in temperature and/or oxygen concentration leads to an increase in the hydrophobicity of fluorite (CaF2) with adsorbed oleate. Subsequently, ex-situ Fourier transform infrared (FT-IR) transmission studies suggested that this increase in hydrophobicity was the result of double-bond reactions between adjacent oleate species adsorbed at the fluorite surface. Now an in-situ FT-IR study on single crystals of fluorite has been used to monitor this phenomenon using internal reflection spectroscopy (IRS) with the crystals serving as reactive internal reflection elements. The double-bond reaction has been correlated with in-situ adsorption density measurements. These results demonstrate that only the first chemisorbed oleate layer undergoes the double-bond reaction at an appreciable rate. However, multilayers of precipitated calcium oleate in the case of fluorite appear to react minimally even for oxygen saturated solutions at elevated temperatures.

Jan 1, 1991

By K. Biswas, S. J. Jung

Health and safety of workers in mineral industry in the U.S. is still a vey important issue as Mining along with Agriculture, Forestry and Fishing and Construction industries have contributed most of the fatal occupational injuries ill between 1980 - 1995 (Worker Health Chartbook, 2000). Health and safety issues, especially for the mining or related excavation industries, arise either from exposures of the human workers to the contaminants liberated or generated by mining operations that have adverse effects on human health (for example coal dust etc.) or from the exposures of the human workers to hazardous working environment that constitutes mining operations (for example blasting etc.). One of the biggest challenges is to understand the combinatorial effect of numerous work-condition (e.g. exposure to dust) and human-factor (e.g. smoking habit) variables on a health or safety-condition variable (e.g. incidence rate of a disease). This paper uses an example dataset on Coal miners' cough problem to illustrate the applicability of Generalized Linear Modeling (GLM) in understanding the relation between cough and other response variables, such as, age, height, smoking habits, time of underground exposure etc.

Jan 1, 2002

By W. Addy Majewski, Kenneth L. Bickel

The U.S. Bureau of Mines (USBM) and Diesel Controls Limited evaluated a new diesel emission control system on an underground mine vehicle. The system was a catalyzed ceramic wall-flow diesel particulate filter (CDPF) combined with an catalytic converter, or diesel oxidation catalyst (DOC). This paper describes the design and installation of the system on a load-haul-dump (LHD). The results of screening tests conducted by the USBM are also given. The screening tests were conducted to determine if the device's particulate collection efficiency, regeneration temperature, and effect on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions changed over the period it was being used. The system was removed from the LHD and evaluated in the laboratory after operating for 308 and 1200 hours. After 308 hours of operation, laboratory testing revealed its particulate collection efficiency varied from 41.0 to 93.5 percent, depending on engine operating conditions. Its regeneration temperature was about 415° C. It reduced HC emissions by up to 97.6 percent, and CO by up to 95.0 percent. When tested in the laboratory after operating for 1200 hours on the vehicle, no significant change in performance was observed.

Jan 1, 1995

By J. H. Daniel

Dust-related respiratory disease remains the major health concern in mining, and health agencies are proposing more stringent standards. The U.S. Bureau of Mines (USBM) is investigating techniques to continuously monitor respirable dust in real-time during the coal or ore extraction process. Continuous monitoring will allow mine operators to evaluate hazardous dust concentrations and adjust the operations to produce less dust. Mine instrumentation applications include machine-mounted and hand-held monitors, personal monitors, and area/environmental monitors. Six dust detection methods have been considered to meet application requirements. These are: light-scattering instruments, a smoke-particle detection technique, correlation of pressure drop across the collection filter with amount of dust deposited, the Tapered-Element Oscillating Microbalance (TEOM) instrument, a method that relates the amount of dust collected on a filter with the vibration of the filter, and beta attenuation measurement of dust. Studies to date have identified the TEOM instrument and the technique of correlating the amount of dust collected with the vibration ofthe filter as having the most promise for success. Development of the machine-mounted monitor is the highest research priority. The application options and progress to date in developing continuous monitoring instrumentation are presented.

Jan 1, 1995

By C. I. Basilio

Pearson's hard and soft acid and base (HSAB) principle may be applied to flotation systems. The HSAB principle states that hard acids prefer to bond with hard bases and soft acids prefer to bond with soft bases. By determining the Drago E and C parameters for the different components of a flotation system, the HSAB principle could be used to explain the selectivity of some collectors such as thionocarbamates against some minerals. Determination of these parameters is done by utilizing Drago's theory and flow micro-calorimetry.

Jan 1, 1991

By Hang Yang, Linneas W. Laage

A major concern of mine fires is the heat generated ventilation disturbances which can move products of combustion (POC) through unexpected passageways. Fire emergency planning requires simulation of the interaction of the fire and ventilation system to predict the state of the ventilation system and the subsequent distribution of temperatures and POC. Several computer models were developed by the U.S. Bureau of Mines (USBM) to perform this simulation. The most recent, MFIRE, simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influence such as varying outside temperatures, and internal influences such as fires. Extensive output allows quantitative analysis of the effects of the proposed alteration to the ventilation system. This paper describes recent USBM research to validate MFIRE's calculation of temperature distribution in an airway due to a mine fire, as temperatures are the most significant source of ventilation disturbances. Fire tests were conducted at the Waldo Mine near Magdalena, NM. From these experiments, temperature profiles were developed as functions of time and distance from the fire and compared with simulations from MFIRE.

Jan 1, 1995