Search Documents

By William M. Turner

Thermonics is a methodology of ground-water flow system analysis based upon the distribution of heat within the subsurface as influenced by moving ground water. Thermonics is based upon the Stallman Equation 1 (1) which describes the simultaneous transfer of heat through a porous medium which contains moving ground water. The Stallman Equation is:

Jan 1, 1980

By A. Haghighat, B. Lattimer

"Mine face ignition due to a high levels of methane is one of the most common fire incidents in underground coal mines. This work exams ignition scenarios in continuous miner headings. Depending on the magnitude of the ignition or resulting fire, the ventilation curtain in the continuous miner (CM) heading may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to the ventilation curtain on the ventilation flow into the CM area. The computational fluid dynamics software Fire Dynamics Simulator (FDS), Version 6.0 was used to predict the conditions that develop due to a 200 kW fire in the coal mine face following a methane ignition with different levels of curtain damage. Smoke layer depth, temperatures and mass flow into the CM area were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed of the curtain. Partial removal of the curtain allowed more smoke to accumulate in the CM area and a reduction in ventilation into the CM area. With full removal of the curtain, the smoke accumulated through the entire depth of the CM area and flowed out the entrance to the CM area and the ventilation completely bypassed the region. INTRODUCTION Active working faces in underground coal mines are one the most hazardous locations in terms of fire events. According to Mine Safety and Health Administration (MSHA) data analysis, the highest number of non-fatal fire incidents was reported at mining faces, intersections and crosscut areas in comparison with other locations from 2000 to 2012. About 464 fires happened at active working faces from 2000 to 2012, most consisting of a methane ignition, in some cases followed by localized fire. These are high risk incidents due to the potential to raise float dust and damage ventilation systems, particularly auxiliary systems such as curtain or tubing. Depending on the magnitude of the ignition or fire, the ventilation curtain in the continuous miner (CM) area may be damaged or dislodged, affecting the ventilation into the area. Five computational fluid dynamics (CFD) scenarios were considered to investigate the smoke layer depth, temperature, visibility, mass flow rate, and the behavior of airflow in an entry with a continuous miner (CM) located in it. The state of the auxiliary ventilation was varied based on the assumption that as an ignition increases it magnitude it will affect ventilation curtain proportionally. Visibility and temperature along the height of the entry at different sections were investigated and the interface height at each section was determined. Also, the fresh air height was studied for tenability analysis in future. FDS, Version 6.0 was used to predict the conditions that develop due to a 200 kW fire on the coal mine face following a methane ignition with different levels of curtain damage. Smoke view software was used as the post processor to visualize and analyze methane fire behavior at the face. Most entry fires are reported as fuel-controlled fires as they are rarely restricted to air access (Ingason et al, 2014). The working face fire in the following models was assumed to be a fuel-controlled fire."

Jan 1, 2016

By M. Z. Rashad

The intersections of numerous joint sets at the surface of tunneling region of Abu-Tartour-Project in Egypt create blocks with irregular shape and size in the rock mass. Most of these blocks are not able to move into the free space of the tunnel. Few key blocks are in a position to move and as soon as they begin so, some restrained blocks will be liberated. The aim of this work is to find the (removable) key blocks for walls, floor, roof and corners of a portion of the tunnel under jointed surface rocks; and then determine the best tunnel direction.

Jan 1, 1991

By E. L. Montgomery

Salar basins in the Andean Highlands of Northern Chile contain ground-water resources which could be used to satisfy requirements for the mineral industry in the region. Salars occur in arid zones; average precipitation is about 200 millimeters per year at altitudes of about 4,000 meters, and average annual evaporation is two meters or more. The salar basins are hydrogeologic sinks where water flows from recharge areas at the margins of the basins to discharge areas at the salt encrusted salar at the lowest point of the basin floor. Groundwater circulation occurs principally in the alluvial and fractured bedrock aquifers. Results of pumping tests for exploration and production water wells indicate a range in maximum sustained pumping yield of 62 to 126 liters per second, and where abundantly fractured, ignimbrite comprises the most prolific aquifer. Chemical quality of groundwater is good. Long-term pumping from properly located production wells in the salar basins would result in lowering of groundwater levels and salvage of water in areas where groundwater is lost via evaporation.

Jan 1, 1986

By Z. J. Hladysz

The Hladysz Rock Tester was developed at the South Dakota School of Mines as a portable rock strength tester. The hand held device is placed against a rock surface and struck by a hammer. The impacted force causes a steel ball in the device nose piece to indent the rock and simultaneously indent a standard steel bar also contained in the nose piece. By comparing the two indented diameters the compressive strength of the rock can be calculated using laboratory determined correlation coefficients.

Jan 1, 1984

By D. R. Rice

Separation of valuable constituents from a complex mineral mixture was examined. Nitric acid leaching produced a solution containing copper, zinc, iron and a large proportion of silver. The residue contained antimony, lead, the remaining silver and elemental sulfur. A caustic sodium sulfide leach dissolved the antimony from the residue, producing an insoluble, high-grade silver-lead product and a filtrate for electrolytic recovery of antimony. The pH of the primary filtrate was raised, precipitating the iron and leaving a solution containing the copper, zinc and the soluble portion of the silver, which would be recovered by conventional means.

Jan 1, 1969

By Jean-Michel Rendu

On April 30, 2003, representatives of the Society for Mining, Metallurgy and Exploration, Inc.(SME) met with the staff of the Division of Corporation Finance of the U.S. Securities and Exchange Commission (SEC). The meeting was held to discuss issues related to the estimation and publication of mineral resources and ore reserves. It took place in the Washington, D.C. offices of the SEC. SEC staff members included Roger Schwall, assistant director, Division of Corporation Finance; Jill Davis, senior accountant; Roger Baer, senior mining engineer; Carl Chavez, chief mining engineer; Ron Winfrey, senior petroleum engineer; and John Murphy, senior petroleum engineer. SME committee members included JM Rendu, independent consultant and chairman of the SME Committee on Resources and Reserves; Ian Douglas, manager of deposit modeling and reserve estimation with Newmont Mining; Art Graham, director and mining engineer with Deutsche Bank Trust Company Americas; Larry Smith, chief geologist with AMEC Mining and Metals Consulting; and George MacDonald, vice president of exploration with Freeport-McMoRan Copper and Gold.

Jan 1, 2003

By X. Zhu, Chen. L., R. Guru, M. Peiravi, M. Mohanty, L. Ackah, B. Xu

"The overall goal of this study is to develop a suitable flow sheet to extract rare earth elements (REEs) from coal ash. A total of 14 coal samples of different ranks were examined for REE concentration, and an anthracite coal sample with the highest REE concentration of more than 700 ppm in the coal ash was selected for REE extraction tests. This paper reports on the results of the experimental program completed in the first part of the study, which included hightemperature leaching with nitric acid followed by solvent extraction tests using various organic extractants, namely, tributyl phosphate, Cyanex 572, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and their combinations. A 4×2×2 experimental design was used to conduct a total of 32 high-temperature leaching tests by varying acid molarity at four levels, solids content at two levels and leaching time at two levels. The highest recovery rates of 90 percent for light rare earth elements (LREEs) and 94 percent for heavy rare earth elements (HREEs) were obtained from the optimum leaching test conditions while maintaining impurity recovery to the leachate at less than 40 percent. D2EHPA was found to be the best extractant in this solvent extraction test series, providing an REE recovery rate of nearly 99 percent.IntroductionGlobal demand for rare earth elements (REEs) and other strategic metals is increasing rapidly due to their use in a variety of advanced technological applications, with more than 100 kt of rare earth oxides used worldwide on an annual basis. The United States has less than 10 percent of the world reserves of REE mineral deposits, and in 2013 imported more than 60 percent of its rare earth oxides from other countries, mainly China (United States Geological Survey, 2017). China’s institution of export quotas has significantly reduced supply to the United States, raising the urgency of finding new ways of producing REEs and/ or substitutes. Coal combustion byproducts, which are usually discarded as waste materials, are known to contain REEs in low concentrations that could be extracted with a suitable process flow sheet. This may be a worthwhile route to pursue, considering the short supply of rare earth minerals and the abundance of coal ash in thousands of ash ponds in the United States. More than 110 Mt of coal combustion byproducts are produced annually in the process of satisfying the country’s need for electricity (American Coal Ash Association, 2016), and less than 50 percent of these byproducts are being successfully used in various applications, with the remainder dumped as waste materials in landfills and ash ponds."

Jan 1, 2017

By E. A. Sondreal

Requirements of flue gas desulfurization (FGD) for Eastern and Western U.S. coals will not be the same because of differences in coal sulfur content, ash analysis, and beating value. The effects of these differences and of limited availability of water in the West are the subjects of this paper. Eastern and Central bituminous coals are generally high in sulfur and require removal efficiencies in the range of 70 to 90 percent to meet the Federal emission standard of 1.2 lb SO2/MMBtu. Ash in Eastern coals is low in alkali content and is relatively insoluble in scrubber solutions. High sulfur content and market availability make salable product methods more attractive in the fast and Central United States than in the West. Western subbituminous coals and lignites are generally low in sulfur content, however, only a few deposits could reliably meet the Federal emission standard without FGD, Required removal efficiencies generally fall in the range of 0 to 60 percent to meet the 1.2 lb SO2/MMBtu limit. If the standard were raised to 2 lb S02/MMBtu, approximately two-thirds of Western coals could be burned without FGD. Some Western coals contain ash high in alkali, some of which is soluble in scrubber solutions. This complicates scrubber chemistry, but it also provides the meant for displacing some or all of the limestone requirements when only moderate S02 removal is required. Dry areas in the West would benefit from full commercial developement of dry processes of FGD.

Jan 1, 1974

By Walter Kahn

Increasing consideration is being given to simplifying traditional methods of tracing pipelines and maintaining required temperatures of stored fluids. Because of their reduction in capital costs, virtual elimination of maintenance. ease of control and "cleanliness"; interest in electrical techniques has accelerated. 1,2 Resistance cable and other heaters have been given some attention. but less well known in the recent introduction of thermal conductive coatings. This paper is addressed to the use of thermal conductive coatings for heating fluid-transport piping and storage tanks. Emphasis will be given to the simplicity, efficiency, and versatility of design and application which their unique properties further contribute to the general economics of electrical heating.

Jan 1, 1965

By A. R. Hollbach

This paper presents a succinct overview of the Canadian coal situation. The topics treated specifically are: the rates of growth of coal supply and demand; the relationship between the coal and electricity generation industries which form its dominant market; the unique impact of nuclear generation on coal demand in Canada; and finally, a view of the developing technologies which will create opportunities for growth in the coal industry of the future. Resources The most important element of coal supply is the resource. The disposition of Canada's coal resources has a marked effect on their utilization, since industry in Canada has not generally developed around coal-fields. The distance from the major industrial centres of Ontario and Quebec to the major region of coal supply in Alberta and British Columbia has crested an economic barrier to the expansion of the use of domestic coal.

Jan 1, 1985

By Michael Karmis

The International Conference on Sustainable Development Indicators in the Mineral Industries(SDIMI 2003) was held May 21-23, 2003 on the island of Milos, Greece. The objective of this international conference was to assist the mining and minerals industries in their global transition to sustainable development. The main theme of the conference was the development, monitoring and assessment of sustainable development criteria for mineral operations. Emerging technologies were also presented that can assist in the development of criteria and performance indicators.

Jan 1, 2003

By K. P. Stricker, H. Keddeinis, K. Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300° and 600°C (570° and 1,110°F) is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies, depending on structural homogeneity, porosity, and gangue quantity. Sinters with heterogeneous structures transmit stress to the hematite phase and this favors disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 2, 1984

By Steve Klein

Weak rock is an important consideration in tunnel design and construction due to the difficult ground conditions that are often encountered. Nevertheless, when conditions are favorable high advance rates can be achieved leading to economical tunnel construction. Successful construction of a tunnel in weak rocks depends on correctly anticipating the behavior of these unique materials. The objective of this paper is to provide guidelines that can be used to accurately classify the performance of weak rock in tunnels.

Jan 1, 2001

By R. A. Wyman

"The froth flotation process was patented by E.L. Sulman, H.F.K. Pickard, and John Ballot in 1906 . . . . . . . . . .James M. Hyde installed the first froth flotation process in the U.S., about August 1, 1911, at the Basin Reduction Co. plant, Basin, Montana . . . . . . . . . .By 1914, 42 mining companies were operating or experimenting with the flotation process . . . . . . . . . .The period 1930 to 1960 saw the application of flotation spread to nonsulphide ores and become the key factor in the economic production of many industrial minerals". So states FROTH FLOTATION, 50th Anniversary Volume, published by AIME in 1962. It is interesting, to observe that the Mines Branch, now part of the Canadian Department of Energy, Mines and Resources, was established in 1907 through an act of Parliament entitled, "The Nines and Geology Act". In 1911, a mineral dressing group was formed and a laboratory was constructed. By 1921, an engineer was devoting full time to industrial mineral processing problems.

Jan 1, 1971

By L. E. Allen, J. F. Abel, D. R. Morgan

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for disposal of transuranic waste and is operated by the U.S. Department of Energy (DOE). The repository is located at a depth of 655 m in the Permian age salt beds of the Salado Formation, 40 km east of Carlsbad, NM. A key component in the design of the WIPP repository is the installation of concrete structures as panel seals in the intake and exhaust drifts after a panel has been filled with waste containers. The DOE has proposed several panel closure design modifications to the EPA. EPA approval of the changes is required since the details of the designs are specified in EPA’s final rule as a condition for WIPP certification. The Environmental Evaluation Group, in its role of providing technical oversight on the WIPP project, has evaluated the proposed modifications. An analysis of this evaluation is discussed.

Jan 1, 2003

By E. M. Frizzell

Decisions affecting ground control design require detailed knowledge of roof rock geology. This is especially true when weak roof materials and anomalies create hazardous conditions and. if not properly supported, result in roof falls. The U.S. Bureau of Mines has developed a system to evaluate geological conditions by using a roof drill that will provide an estimate of the compressive strength of the roof rock in real time. Through the use of sensors and a microcomputer on the roof drill critical drilling parameters can be interpreted and analyzed almost instantaneously, making it possible to inform an operator of hazardous roof conditions such as voids and changes in strata during the drilling process. Geotechnical data can be downloaded to a portable semiconductor memory device, which is brought to the surface so that data can be directly accessed with a personal computer for further analysis. Results from field tests are presented.

Jan 1, 1992

By H. J. Handewith, W. D. Coski

This paper describes the development and testing of the RAMEX excavation system. Incorporating a synergy of low velocity, high energy impact and kerf cutting, this machine offers a competitive alternative to drilling and blasting in hard rock. It is a boom mining machine that incorporates the features of a lightweight roadheader and it can mine nearly any shape opening in hard rock. The RAMEX Tunneler has been developed to satisfy industry demands for a non-explosive, flexible, continuous and rapid underground rock excavation system. It will produce minimum ground vibration in the urban environment and allow the flexibility necessary for thin seam mining conditions. It will also reduce initial ground support costs and has a minimum impact on rock integrity. Developed by RAMEX Systems with cooperative research provided by the U.S. Bureau of Mines, this system, could produce the next step in the continuing evolution of mechanical mining systems.

Jan 1, 1989

By Howard J. Handewith

Long used in mine development in England, Europe and Russia, roadheaders are growing in size, features, productivity and application. Beginning with the basics, this paper covers the economic and the technical aspects of the new roadheaders in both mine production and development. The author explains how to choose and integrate roadheaders into ongoing operations as another step in the inexorable march from labor to capital intensive mining. Innovations now on the drawing boards are covered that are the challenge of the future.

Jan 1, 1983

By S. Veeramasuneni

The interaction of soluble salt particles in their saturated brines is of interest from both a fundamental and practical perspective. The state of dispersion/aggregation of alkali halide particles as determined by optical microscopy can now be described based on non-equilibrium electrokinetic measurements for alkali halides. These results indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. These experimental results can be explained based on the interfacial polar interaction theory. In this regard the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems.

Jan 1, 1997