Search Documents

Column flotation cells continue to gain acceptance in the coal industry for the treatment of high-ash streams containing clay slimes. Unfortunately, some industrial installations have failed to meet expectations due to improper scale-up, incorrect operation and poor ancillary circuit design. To overcome these problems, case studies have been conducted to fully define the capabilities of column cells for coal applications. These data have been used to develop generic engineering guidelines for column circuit design and operation. An economic analysis has also been conducted to illustrate the importance of key capital cost considerations. These analyses indicate that column cells are significantly more expensive than conventional machines, although this difference can be greatly reduced through the installation of very large-diameter columns.

Jan 1, 1999

By T. C. Eisele

The separating efficiency of a flotation column is largely limited by the degree of backmixing of tailings into the froth zone, and its recovery is limited by the degree of short-circuiting of feed to the tailings. Current columns are typically made very tall, on the order of 30-40 feet, in order to limit the effects of backmixing and short-circuiting. These effects can also be reduced in a much shorter column, provided that the flow in the column approaches plug-flow. In this work, horizontal baffles were shown to improve the performance of a 6-foot tall laboratory-scale flotation column treating a difficult-to-clean, heavily oxidized coal. Tests with variation in the position of the baffles showed that for the greatest benefit, baffles are needed both above and below the feed inlet. Tracer tests with a fluorescent dye water tracer showed that the addition of the baffles reduced the amount of feed water entrained into the froth at any given coal recovery.

Jan 1, 1994

By T. J. Durbin

At some surface and underground mines, control of ground-water inflow involves significant costs. These costs include the capital costs for installing a dewatering system, power and other costs to operate and maintain the system, and costs to treat and dispose of the water that is collected. To minimize these costs, design of a dewatering system utilizing wells has been formulated in terms of a nonlinear operations research problem using quadratic programming. Using this formulation, the locations, depths, pumping rates, and pumping schedules of wells are selected so as to minimize the total costs of the dewatering system.

Jan 1, 1993

?Energy-related systems: wind, solar, electric are typically materials intensive. As new technologies are widely deployed, significant quantities of the elements required to manufacture them will be needed. However, many of these unfamiliar elements are not presently mined, refined or traded in large quantities, and, as a result, their availability might be constrained by many complex factors. A shortage of these ?energy-critical elements? could significantly inhibit the adoption of otherwise game-changing energy technologies. This, in turn, would limit the competitiveness of the U.S. industries and the domestic scientific enterprises and, eventually, diminish the quality of life in the US.? -Energy Critical Elements: Securing Materials for Emerging Technologies?- American Physical Society, 2011.

Jan 1, 2012

By Anthony Edey

It is a generally accepted and widely discussed fact that the world in general, and the United States in particular, face a shortage of energy at the present time which will become worse in the future. There is, however, no sign of a similar concensus as to the actions which would prevent or overcome this expected shortage. An immense variety of solutions has, however, been put forward, ranging from the purely political to the outer fringes of sophisticated technology. One resource which surprisingly is often only cursorily included in this discussion is the immense known petroleum reserve lying within the United States. When this subject is discussed, indeed, it is usually in the context of the improvements in production or new discovery rate that could be expected to result from possible politico-economic actions that would raise the real price obtained for domestic crude. This interest in the potential for improved domestic production is undoubtedly justified, but very little attention is normally drawn to the fact that even under the most favorable policy framework the majority of the oil that has been, or will be, discovered will remain in the ground due to the inherent limitations of production through surface wells.

Jan 1, 1979

By S. Gupta

Froth flotation is a process commonly employed for the selective separation of phosphate from unwanted mineral. Column flotation has become widely accepted in the mineral processing industry, including phosphate industries, due to its ability to improve selectivity, lower operating cost, lower capital cost, and superior control. In this work, a hybrid model is developed that combines a physicochemical model with artificial neural networks. The physicochemical model is based on axial dispersion with first order collection rates. A new approach, in which both frankolite (the desired mineral containing phosphate) and gangue (undesired product) are modeled, enables prediction of grade of the recovered product. Thus, two basic parameters are required in this model: flotation rate constants for frankolite and gangue. Artificial neural networks are used to predict flotation rate constants. The model also takes into account the particle size distribution and predicts grade and recovery for each particle size range. The model then combines grade and recovery for each particle size range to determine the overall grade and recovery of the column. The model is validated against laboratory column data.

Jan 1, 1998

By M. R. Smith

Barrick Goldstrike Inc.'s Betze/Post Open Pit is located at the north end of the Carlin Trend, in Eureka County, Nevada, U.S.A. (see location Map, Figure 1). About ten open pit gold mines exist on the trend, which strikes northwesterly, through the north end of Eureka County and into Elko County. The final Betze/Post Pit configuration is shown in Figure 2, Pit Configuration. The final pit will be about 2450m long by 1550m wide, elongate in a west-northwesterly direction. The pit straddles the Barrick/Newmont property boundary. The highest elevation of the pit perimeter is 1800m at the south wall, with the east end pit bottom elevation at 1200m.

Jan 1, 1993

By William S. Fyfe

The world's biomass with its species-specific ability to concentrate metallic elements must provide one of the dominant concentration and transport systems for such elements. Given that about thirty elements are now considered bio-essential, for all these biomass may control their environmental behavior. Life appears to be present in almost all places where liquid water is present at temperatures near 100°C or below. In the surface environment a very large array of simple minerals are produced in living cells and such processes can lead to economic concentrations. Because of the specific nature of bioconcentration of elements, in all environments where biomaterials accumulate, interesting metal concentrations may occur or the molecular fragments from bio-degradation may allow specific metal transport and concentration. The scale of biological-inorganic interactions on our planetary surface is still inadequately appreciated.

Jan 1, 2013

By Michael G. Nelson, Amy Richins, Ashley Hodgson, W. Pratt Rogers

"Sociotechnical systems are everywhere in the modern industrial world. Sociotechnical systems describe how humans interact with technology throughout a variety of processes. These systems are prevalent in modern industrial settings, such as operating mines. Safety and health management systems (SHMSs) are complex sociotechnical structures designed with the aim of managing and reducing occupational risk. U.S. mining companies are voluntarily adopting SHMSs to supplement regulatory safety compliance efforts. Like all complex sociotechnical systems there are a wide variety of approaches and adoption philosophies around a SHMS. Many SHMSs suffer from high levels of redundancies, which manifest themselves in diverse ways: duplicate processes, forms, permits, and tracking mechanisms. These redundancies have severe impacts on the overall system and absorb critical culture and leadership “energy”. A recent study initiated by the University of Utah and sponsored by the Alpha Foundation is investigating the effectiveness of SHMSs across 15 different U.S. mining sites. A large amount of data has been captured to help characterize elements of SHMSs and correlate their impacts on safety outcomes. Many variables were assessed in the study. Those of importance to this paper are the variables describing the robustness of the sociotechnical aspects of the SHMS. Two such variables are the overall integration of the SHMS within the whole system and how data is managed. Data management in this context deals with the approach to capturing, analyzing, and acting on data within the system. As well, systems are integrated around controlled, data-sharing mechanisms. It has been found that wide variety of approaches has been taken to integrate the SHMS within the governing management philosophy at a given site. A series of case studies is presented that develop some specific best practices for proper data management and integration of SHMSs.Introduction and Project Background Managing occupational health and safety can be done in many different ways, and with many different approaches, but is often based on the host country’s regulatory and industrial culture. However, many companies have extended their effort beyond the regulatory requirements of their host nation and have implemented Safety and Health Management Systems. The goal of these efforts is to reduce and eliminate occupational risk. Many health and safety practitioners have a hard time justifying various elements of health and safety management. There is a lack of institutional knowledge that measures and assesses the effectiveness of these Safety and Health Management System (SHMS) elements. To better understand the effectiveness of SHMSs the Alpha Foundation has funded a research project with the University of Utah. The title of the project is “Characterization and Effectiveness of Safety and Health Management Systems in the U.S. Mining Industry.” The research team will assess the SHMSs of 15 United States mine sites. The outcome of the project will be a method to characterize the strength of the SHMS elements, assess a culture and leadership index, and finally establish correlations between elemental risk and safety outcomes. The study is currently in progress. However, many important outcomes have already been observed, particularly on the data management practices within an SHMS."

Jan 1, 2017

By K. V. Raj, T. Bhowmick

"Computational fluid dynamics (CFD) modeling of an open-pit mine has several challenges. A good quality mesh of the model domain is a pre-requisite for convergence in solution. Good quality tetrahedral meshing and insertion of prism layers in faceted open-pit mine geometry is complicated due to presence of numerous vertices and ridges. Presence of vertices and ridges result in poor quality tetra elements and holes in prism layers, which cause instability in the model. Good quality pit bottom prism mesh elements significantly improve the formation of velocity boundary layer and thermal boundary layer at the pit bottom. This results in an expected temperature dependent micrometeorological buoyancy flow in the pit. Whereas, model geometry without a prism layer, results in abrupt temperature gradient near pit bottom. Buoyancy flow and recirculation have significant effect in lifting mechanism of fugitive dust particles generated near pit bottom. Representative initial and boundary conditions and selection of appropriate turbulence model have significant influences on the simulation results. In this paper, three-dimensional models of open-pit mines are developed using commercial CFD software (CRADLE-CFD). Important constraints and various consequences in modeling complex open-pit geometries are presented. INTRODUCTION Application of Computational fluid dynamics (CFD) to model an open-pit mine to predict fugitive dust and pollutant concentrations in and around a mine is relatively new. In former Soviet republic (USSR), Baklanov [1] and Belousov [2, 3] presented numerical models of pollutant transport in open-pit mines in Arctic regions. In recent years, advances in mathematical and computational fields have enabled better modeling of pollutant dispersion phenomenon around mines using computational fluid dynamics (CFD). Several CFD software packages have been used by various researchers to model the pollutant transport in open-pit mines. Works by Alvarez et al. [4]; Lowndes et al. [5]; Silvester et al. [6]; Torno et al. [7]; Choudhury and Bandopadhyay [8]; Collingwood et al. [9]; Raj et al. [10] and Flores et al. [11]; are examples of application of various commercial and open source CFD packages (COMSOL, ANSYS, OpenFOAM) to model pollutant transport in open-pit mines. These researches provided a strong background for additional research involving CFD modeling of open-pit mines. Due to the limitations of computational times and capacity, 3D modeling and various aspects of fugitive dust dispersion in open-pit mines remained unexplored."

Jan 1, 2015

By Felicia F. Peng

The naturally occurring aged manganese oxide coated on the granular media was found to have a catalytic effect on the removal of low concentration of Mn(II) (-1 ppm) from drinking water. Applying this principle, a manganese removal technique was developed for removal of higher concentration of Mn(II) (-100 ppm) from mine drainage by using various aged filter media and synthesized granular media with manganese oxide coatings. Laboratory-scale continuous granular media column experiments were conducted to assess the feasibility of manganese oxide-coated granular media for Mn(II) removal from synthesized mine drainage. The removals of Mn(II) were evaluated as a function of operation parameters including solution pH, manganese oxide concentration coated on the media, interstitial velocity, and oxidant concentration of influent. Higher solution pH and/or higher manganese oxide concentration promoted the removal of Mn(II) on the oxide-coated granular media under low interstitial velocity. Addition of sodium hypochlorite as an oxidant in the influent resulted in continuously regenerated oxidized surface to serve as the catalyst for Mn(II) oxidation reaction on the surface of oxide-coated media.

Jan 1, 1994

By J. B. Cabezas

The metallurgical processes that are frequently applied today use strong solutions and are of alkaline, acidic, or organic nature. These play a very important part in recovery of values from many ores. These solutions are of such a chemical nature that they are generally corrosive, flammable, and contaminating. In most cases, they are highly dangerous to the environment. Within the extractive metallurgical industry, it is also very common to have to deal with the handling of contaminating solutions with a high content of cyanide, arsenic, mercury, lead, copper kerosene, acid and many other components whose temporary or permanent confinement within the process must be adequate and absolute.

Jan 1, 1986

By Lawrence Tsang, Conrad Ng, Tim Leung, Peter Poon

"The Mined Tunnel is part of the Central-Wan Chai Bypass and Island Eastern Corridor Link (CWB), which is a strategic road along the northshore of Hong Kong Island targeted to alleviate the heavy traffic congestion. The objective of this paper is to review the performance of construction of a 160m long Mined Tunnel with a trinocular cross-section area of 460m3 and a combined span of about 50m underneath the southern approach ramp of the existing Cross Harbour Tunnel (CHT) by sequential excavation method (SEM) in hard rock. Mechanical excavation of tunnel by adopting the New Austrian Tunnelling Method (NATM), together with the application of NGI Q-system allows observational approach and optimization of temporary rock support design. Furthermore, the good performance of optimized rock support and the stability of CHT are confirmed through instrumentation monitoring review. This paper also discusses the selection of different tunnel plant and equipment to achieve the planned rates of tunnelling by mechanical excavation in competent granitic rock. INTRODUCTION The works of the CWB mainly comprise construction of 4.5km dual three-lane trunk road, of which a 3.7km section is a tunnel connecting Rumsey Street Flyover in Central to Island Eastern Corridor at North Point (see Figure 1). The Mined Tunnel runs from the ex-Public Cargo Working Area (ex-PCWA), underneath the existing CHT, and through the Causeway Bay Typhoon Shelter. The Mined Tunnel passes at an oblique angle beneath the southern portal of CHT over a length of some 50m. CHT is the primary sensitive receiver of this project and is utilized with a daily throughput of about 120,000 vehicles that far exceeds the design capacity of 78,000 vehicles per day. Hence it is necessary to choose the most appropriate tunnelling method to preserve the structural integrity of the CHT. Other sensitive receivers in the vicinity include structures to the north of the Mined Tunnel, the Royal Hong Kong Yacht Club (RHKYC); and to the south of the Mined Tunnel, the Police Officers’ Club (POC)."

Jan 1, 2016

By Henry T. Miller

INTRODUCTION The basic purpose of this paper is to suggest procedures and practices to insure that no employee working in a uranium milling operation receives exposure to radioactive, toxic, or other materials or agents that might produce a permanent, deleterious effect upon his physical health and well-being. This program is also designed to insure that each employee can carry out his assigned duties without risk to his health or to that of his fellow workers. The assumptions underlying this program are by necessity, conservative, with emphasis being placed upon prevention rather than correction or reaction to an undesirable situation. The limits specified-either as Threshold Limit Values (TLVs), Maximum Permissible Concentrations (MPCs), or Radiation Protection Guides (RPGs)--represent both standards of best practice and those of law and regulation. The total program is envisioned as a balanced combination of occupational hygiene and radiation monitoring. This includes surveying, air sampling, personnel dosimetry, bioassay, medical surveillance, epidemiology, and training--all backed by a thoroughly tested and evaluated set of emergency procedures. The program, as presented, is keyed to the results of monitoring, surveying, air sampling, medical surveillance, and epidemiology--it being obvious that no problem can result when no hazard can be identified. The lack of an identified hazard, however, does not negate the need for such a program and prudence suggests the need for routine surveillance programs in the best-designed facility. [The Model Mill] The model mill used in this paper is that presented by the U. S. Environmental Protection Agency in its study of the uranium fuel cycle1. The model mill processes 600,000 metric tons of ore per year into 1,140 metric tons of U308 as yellowcake per year using an acid leach process. Other characteristics of the mill such as location, tailings dam design, number of light water reactors supported, and geographical location are not pertinent to this paper. The usual remote western location of these facilities produce some difficulties in delivering the required occupational medical services and is not within the scope of this paper. The operating lifetime of most mills is commonly estimated as from 12 to 15 years in actual practice; however, the U. S. Environmental Protection Agency estimated a 20-year lifetime for its model. The principal steps in the acid leach process include :2 (a) Ore is blended and crushed to pass through a 2.5 cm (one inch) screen. The crushed ore is then wet ground in a rod or ball mill and is transferred as a slurry to leaching tanks. (b) The ore is contacted with sulfuric acid solution and an oxidizing reagent to leach uranium from the ore. The product liquor is pumped to the solvent-extraction circuit while the washed residues (tailings) are sent to the tailings pond or pile. (c) Solvent extraction is used to purify and concentrate the uranium. (d) The uranium is precipitated with ammonia and transferred as a slurry. (e) Thickening and centrifuging are used to separate the uranium concentrate from residual liquids. (f) The concentrate is calcined and pulverized. (g) The concentrate or yellowcake is packaged in 208 liter drums for shipment. This process is illustrated in Figure 1.3

Jan 1, 1981

By Martin P. Schroeder

"Challenges have emerged as subway systems age and as new tunnels are bored in congested corridors or in high-risk environments. To help public transportation agencies address tunneling challenges, the American Public Transportation Association has convened numerous independent industry peer reviews composed of top experts in their fields to come together and provide recommendations and solutions. This paper provides case histories of peer reviews that include topics such as boring through toxic soils, boring underneath existing tunnels, retrofit of tunnel ventilation systems, and mitigation of water intrusion. Peer reviews are applicable to all tunnel projects worldwide. The paper will highlight the conditions of these challenges, peer review recommendations, steps taken to reach agreement, and the successes that resulted, which led to major changes, new legislation and reduction of risk. INTRODUCTION Public transit agencies face many challenges in maintaining and expanding safe transit operations, especially as systems age, ridership expands, and budgets remain flat. The development of new industry standards and federal safety regulations places further demands on transit systems, with compliance often taxing in-house resources. Studies of the state-of-good-repair across US public transit systems indicate a current backlog of $84 billion in maintenance projects, which will require an investment of $18.2 billion per year to eliminate the backlog by 2030[1]. Systems not in a state-of-good-repair may not operate efficiently, may not be available to meet the growing ridership demands, and may not meet required safety goals or reduction of risk. Innovation is another clear need transit agencies have for improving system performance and lowering operating costs.To meet these challenges, transit agencies often turn to industry peer reviews for guidance and recommendations as part of their overall strategy to maintain and grow the safe operation of their systems. As a service to its members, the American Public Transportation System (APTA) has developed an industry peer review program designed to give agencies opportunities to learn from each other and help them address challenges in operations, engineering design, and construction of their systems. Over the past 20 years, APTA has performed hundreds of peer reviews covering all aspects of transit system operations from fare collection to agency organization, project delivery methods to safety culture, and engineering design including tunneling and tunnel fire ventilation. As rail transit systems expand to meet increased ridership, it is often necessary to bore new tunnels for alignments in congested areas where surface rights-of-way are lacking. Such proposed alignments can pose significant challenges for transit agencies, as they contend with various tunneling problems."

Jan 1, 2016

By R. Asmatulu

According to Darcy's law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By D. R. Nagaraj

There are few organic ligands that can adsorb effectively on noble metals, especially gold, in aqueous media. Ligands containing sulfur and nitrogen donors are known to be the most effective. Dithiophosphorous acids, for example, are known to adsorb on gold under certain conditions and these, along with xanthates, are used traditionally to recover gold values by flotation from ores. These compounds, however, are not necessarily selective for gold since most of the associated sulfide minerals are also floated. Monothiophosphorous acids, on the other hand, were recently discovered to float gold values selectively from sulfide-containing ores in a mildly alkaline medium; thus the dicresyl monothiophosphate is now used commercially in a gold flotation operation in the U.S.

Jan 1, 1991

By Richard P. Killmeyer

In 1985 the Pittsburgh Energy Technology Center (PETC) of the U.S. Department of Energy (DOE) conducted a study to evaluate the emerging selective agglomeration processes (Killmeyer, 1985). This paper covers a recent similar study evaluating an associated technology, the emerging advanced froth flotation processes. This study has goals similar to those of the 1985 study: to evaluate the emerging froth flotation technologies collectively and determine how far they have progressed in their ability to clean ultrafine coal, and to assess the differences among the participants. The major concern again in this study was not the level of development, nor the economics of each individual process but only the current technical performance.

Jan 1, 1989

By Roger S. Dewey

1.1. INTRODUCTION Despite indications of a general economic recovery in the U.S. during the mid-19801s, mine operators have not generally shared in the benefits of these reported better times. Budgets have not rebounded, borrowing is tougher, parent companies' pockets are not as deep as in previous years, and margins are not any better -- if there is any left over at all. Managing capital equipment budgets is always a challenge, and the last five years of stretched equipment lives make these decisions more tenuous. Delays and avoidance of replacements due to tough times inevitably makes those decisions increasingly difficult and usually more expensive The purposes of this paper are to present. a brief refresher outline of the fundamentals of equipment replacement analysis, to suggest a number of papers where analysis methods are explained in greater detail. and to recommend the use of a widespread microcomputer software capability (1-2-3) as the easiest path to a much-needed solution for a very difficult, and usually under-supported management decision problem 2. REPLACEMENT DECISION POLICY Investments in equipment replacements must compete for capital with all other investment alternatives. Capital for replacements of ten represents a greater commitment than do the new projects which a company might handle in a given year. But. sadly, formal policies for standardized analysis of replacements rarely exist, even in major companies. Yet this policy can be very significant in determining the competitiveness of a firm. Whereas many replacement decisions are based on cost minimization, economists and financial analysts agree that wealth maximization or return on investment is the superior criterion. Though the difference may seem slight, agreement on a firm's financial objective is vital. Replacement policy should be straight- forward. have a logical basis, and a proper level of sophistication. There are several reasons to develop a policy for replacement decision-making: [I] 1 - equipment's optimal economic life is nearly always shorter than its physical life; 2 - mine life often exceeds equipment life, so management must face these decisions routinly 3 - replacement capital costs, on an undiscounted basis, can run 25 to 75% of original capital 4 - technological changes may result in a newer machine or system which can operate more efficiently, more safely. or less expensively 5 - estimates should be made consistently in the fundamental areas of life expectancy, availability, utilization. price escalation, taxes 6 - long-term and short-term budgeting without decent data and analytical capability is nearly impossible, or at least ineffective Policy development assumptions which must be considered include: the planning horizon, cost patterns, interest rates, availability of capital, replacement vs. expansion, technology advances.

Jan 1, 1987

By E. C. H. Becker

When data points, plotted on X-Y coordinates, lie along a simple line, their regression can be matched to a high degree of accuracy by one or other simple algebraic expression (Boot and Cox, 1970). Under these conditions, interpolation is axiomic. Further, if the expression defines no more than a straight line, a parabola or other such line which can be related to some specific mechanism which generates the points, then extrapolation might be valid. However, any extrapolation would depend on the continued, unchanged functioning of the mechanism. Studies of more intricate assemblages of data points have long been based on representation by means of series (Fourier, 1811). If sufficiently complicated, several different algebraic expressions can represent the same intricate regression accurately (Hoerl, 1954). However, without reference to a mechanism, no extrapolation is contemplated. Typically, variations in the prices of minerals with time are. sufficiently complicated to render invalid any simple attempts at extrapolation. The computer, however, can be used to derive algebraic expressions which match complicated regressions and also can be represented by the functioning of a mechanism (Becker, 1984). The techniques involved have been applied with advantage in the study of time series representations of mineral prices.

Jan 1, 1986