Search Documents

By S. Rajan

Familiarity with NEMA standards and the influence of the power supply on the motor-load system permits the user to make the necessary decision as to whether a standard or special motor is needed for his particular application. This paper highlights the more important aspects of NEMA standards for ac induction motors from the application engineer's standpoint and the effect of the power supply on motor characteristics.

Jan 1, 1975

By R. V. Ramani

An improved mine environment is the single most critical factor affecting the health and safety of workers engaged in underground coal winning. A very important subclassification of this wide field is mine ventilation, which essentially deals with 'mine atmospheric environmental control.' To ensure proper mine atmospheric environmental control, adequate quantities of air must flow through working sections in the mine. In recent years much attention has been paid to the fan and its prime movers, but the efficient use of the fan output in the workings has not received an equal amount of investigation. In mechanically ventilated mines friction losses in main airways often account for 70 to 90 percent of the total pressure loss sustained in the system. Also the leakage losses are a serious detriment to the efficiency of mine ventilation systems. It is not uncommon to loose 60 to 70 percent of the air between the fan and the last open cross-cuts due to leakage directly into the return Proper assessment of these losses in simulating and projecting complex ventilation systems is vital. Network analysis of ventilation systems is not new. Scott and Hinsly (1951) presented the detailed mathematical framework. Since then work has been done in adopting this technique to analog, and within the past few years, to digital computers. Development of computer programs to solve ventilation network problems has been reported in United Kingdom, Japan, U.S.S.R., South Africa, Germany, and the United States. The purpose of these programs is to serve as an experimental mine wherein analysis of proposed alternatives or ventilation planning can be tested. The great power of the computer as a planning tool lies in the ability to input empirical or Projected data into programs with predicting ability. But, however good a computer program is, unless fairly accurate input information is available accurately assessing the engineering factors of the ventilation system, the output will be suspect. Thus, to simulate and project mine ventilation systems, good estimates of leakage and friction factors are important. Yet, relatively little work has been done in the past three decades to determine these more realistically.

Jan 1, 1973

By John W. Amos, John A. Christophersen

The Deister No. 7, "77" and "88" Coal Washing Tables have been used by the coal industry in the cleaning of finer sizes of coal (-1/2") since washing of coals became necessary. This paper will deal with the in-plant use of the CONCENCO "88" Deister Coal Washing Table, along with a brief description of the Deister Refuse Superscalper. Efficient in-plant operation of the Deister Coal Washing Table can be accomplished by the adjustment of six basic variables. These variables are: 1. Headmotion 2. Feed 3. Riffle Pattern 4. Dressing Water 5. End Elevation Adjustment 6. Side Tilt Adjustment VARIABLE NO. 1 HEADMOTION The reciprocating movement of the "88" Table is developed within the headmotion entirely by rotating eccentric weights. Four parallel shafts each carry pairs of eccentric weights (Figure 1-A). The shafts are geared together with gears of 2 to 1 and 1 to 1 ratios, so that the two shafts in vertical alignment which carry the small eccentric weights operate at twice the speed of the other two shafts. The other two shafts are also in vertical alignment with each other and carry large eccentric weights. As power is supplied to one high-speed shaft, once each revolution the forces produced by the large eccentric weights are reinforced and then opposed by the small eccentric weights in a horizontal plane. The direction of movement of the table decks is reversed much more sharply at the forward end than at the backboard end of the stroke, causing material to move toward the refuse end of the table. Because in the vertical plane all centrifugal forces oppose each other and cancel out, there is no vertical movement and virtually no impact to the support steel. The "88" Coal Washing Table is suspended by wire-rope cables from three overhead steel beams, and operates with a perfectly uniform and exact differential motion curve in every stroke (Figure 1-B). The decks, being attached to the headmotion, are reciprocated in a parallel line from the head- motion to the refuse corner at speeds varying from 260-300 strokes per minute. Both length of stroke and speed are set at the factory for the coal characteristic desired and should not be changed. A 3 HP motor is mounted on the top of the headmotion and uses 3 V-belts to transmit driving power to the headmotion. The headmotion must be kept running on a horizontal plane. Punch marks are provided on the side and end of the main frame for use in leveling the motion (Figure 1-C). In leveling the motion, the work must always be done with two cables. To level the long side of the headmotion both front or both rear cables are raised or lowered to bring motion back to level. To level side to side, both right side cables or left side cables are raised or lowered to bring motion back to level VARlABLE NO. 2 FEED When tabling different size coals, each deck of a "88" DIAGONAL-DECK Coal Washing Table will handle feeds as described in figure 2-A.

Jan 1, 1988

By D. C. McLean

Early studies in the carbonate leaching of uranium ores led to the investigation of pressure leaching as a method to enhance the dissolution of the metal values in this system. The initial investigations conducted at the University of British Columbia supplemented by the work done by the group at the A.E.C. Grand Junction pilot plant, all established the higher efficiency and better economics of the alkaline pressure leaching system. This work was conducted either in laboratory autoclaves using oxygen overpressures, or in pilot plant sized horizontal autoclaves with air as an oxidant. Both of these testing vehicles utilized agitation provided by relatively high speed impellers (300 to 700 rpm), which apparently enhanced the oxidation of the uranium to the hexavalent state. The installation of vertical autoclaves on a production scale, which through design considerations require relatively slow agitator speeds (68 rpm), led to the studies of the utilization efficiency of the air addition and the use of catalytic type oxidants to effect a greater usage of the oxygen added through the aeration system. In addition to investigating the effects of the chemical additives, studies were also conducted on the effect of different impeller configurations on the extraction of uranium, which in itself is a measure of oxidation efficiency. The material presented in this paper was compiled in the Ambrosia Lake district of New Mexico, and the majority of the data was obtained in the Homestake- Sapin Partners mill, located at Grants, New Mexico.

Jan 1, 1960

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering and display technologies have generated increased accessibility to virtual reality. Virtual reality allows for the creation of dynamic, high-fidelity environments to simulate dangerous situations and test conditions and to visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers developed a virtual-reality framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization and training. This paper describes the features of VR Mine, including mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By Richard E. McGee

The paper presents a description of the procedures that were used to generate a ventilation criterion based on measurements of ambient mine air exhaust pollutant gases and ventilation airflow quantities. Today's economics dictate that a ventilation requirement be based on actual operating conditions. This will assure optimum economics and a safe working environment at the same time. The paper presents a methodology by which a ventilation requirement is based on the average maximum expected concentrations of nitric oxide (NO), nitrogen dioxide (NO2), carbon monoxide (CO), and carbon dioxide (CO2) that equipment operators in one of our Southeast Missouri mines will be subjected to. A graph has been generated whereby the expected maximum levels of NO, NO2, CO and CO2 are plotted against the ventilation quantity of a mine stope.

Jan 1, 1982

By E. H. Cho, Q. Luo

Pittsburgh No. 8 coal, cleaned by conventional froth flotation, was oxidized in a 2-L Parr stirred bench-top autoclave. Autoclave tests were carried out for up to 5 hrs under the following conditions: 150 to 225ºC, 60 to 500 psi 02 and 15 to 60 g of coal per 600 mL of distilled water. The oxidation of coal was evaluated by measuring the total acidic group formed on the surface of the coal and by measuring the adsorption (under standard conditions) of calcium ion from a solution. The degree of oxidation of the coal increased continuously, without much leveling off, with increasing oxygen pressure. With increasing temperature, the oxidation of the coal increased sharply between 150 to 175ºC and then leveled off above 175 °C. The adsorption of calcium was >3% on coal oxidized under the most favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The loss in Btu was found to be sensitive to oxidation temperature. This study concluded that the optimum oxidation of coal is achieved over 3 hrs at high oxygen pressures (e.g., 500 psi) at ~170ºC. This study also concluded that, when measured in terms of calcium adsorption, Btu loss and reaction time, the oxidation achieved in an autoclave is far superior to that achieved in a fluidized bed.

Jan 1, 1996

By H. C. Juvkam-Weld

R. Michael Craig Mr. Juvkam-Wold's article is a timely and much needed presentation of the method of depressurization to reduce ground-water inflow into mine shafts. The article is very informative and discusses the effects of depressurization upon shaft inflows adequately. However, the article omits a discussion of another important benefit of depressurization: the reduction of potential for artesian burst or, as it is also called, floor heave. Confined aquifer systems (artesian aquifers) can contain water under several hunder pounds per square inch (psi) of pressure. For example, water levels at elevations of 455 m (1500 ft) or more above the top of the Westwater Canyon member of Reply by H.C. Juvkam-Wold In general, Mr. Craig's comments are useful and accurate regarding the potential benefits of aquifer depressurization. However, two of his points require further explanation since they may lead to a misunderstanding of my paper and its predictions. These refer to his comments regarding failure to account for storativity and to non-artesian conditions. Equation 5 is indeed Darcy's steady state equation. However, as a careful review of the appendix in this paper will reveal, I have used this equation to represent semi-steady state conditions. In other words, steady state conditions are assumed at any instant of time, but conditions may change gradually from

Jan 2, 1983

By Achille Balossi Restelli, Elena Rovetto, Andrea Pettinaroli

"The Station “C13” of Warsaw Underground Line II, with tunnel crown 10m below the water table, required the excavation of three connection tunnels, underpassing a six-lane in service road tunnel, working from two lateral shafts. After the collapse occurred while digging the first tunnel, the use of artificial ground freezing was chosen to ensure the excavation under safe conditions. A complex freezing pipe geometry and excavation sequencing was necessary because of the interferences of the overlying road tunnel diaphragm wall foundations, shaft internal structures and previous grouting activities. A combined freezing method was used: nitrogen for freezing the tunnel arches, brine for freezing the intermediate wall and for maintenance stages. Sandy and silty sandy layers were frozen around the crowns and sides. No treatment was necessary for the inverts, lying in clay. A monitoring system of ground temperatures and structure movements allowed for successful completion of work in 8 months. INTRODUCTION The C13 Station of the Warsaw Underground-Line II is located on the West bank of the Vistula River. It consists of two shafts and three connecting tunnels, passing under the Wislostrada (WS) Road tunnel. According to the initial geotechnical investigation, tunnels should have been excavated in high-plasticity clay, but during the first borings non cohesive soil was encountered. Additional investigations were performed on both shafts and a more detailed stratigraphy was reconstructed (Lombardi et al. 2015). Layers of fine sand, sandy silt and sandy silty clay were present along the tunnels crown arches and in the North East tunnel they extended down to the centre line (-13.735m above the Vistula River medium level). Based on the new stratigraphy, it was decided to stabilize the crown and control the groundwater inflow from the face with jet-grouting columns extending the treatment down to the clayey soil, but a collapse occurred in the North West tunnel with soil and water inflow inside the shaft."

Jan 1, 2016

By Oscar H. Lentz

During 1960, the controversy over percentage depletion reached the level of debate between presidential candidates. Nixon took the position that he would not tamper with the status quo in this matter. Kennedy took the position that he was willing to take a fresh look at the issues involved. Kennedy's position appears to have been based upon two premises: (1) new sources of federal revenue may be needed; and (2) current depletion rates, even if sound in principle, may be too high and, therefore, inequitable. The latter premise constitutes the basis for the claims that depletion allowances are simply "loopholes" of tax avoidance. Very probably the controversy over percentage depletion will remain in the political limelight during most of the coming decade. It is quite possible that the current depletion rates, at least those for oil and gas, will be reduced during this period. The aim of this paper is to isolate the complex causes of this mounting opposition to percentage depletion.

Jan 1, 1961

By Robert L. Frantz

The various facets of university-company cooperative activities and the opportunities for collaborative research for the mineral industries are presented in this paper. The advantages and disadvantages of various alternative research funding arrangements for the researcher, the university, and the sponsoring corporation are discussed. Examples of university-industry cooperative research programs are briefly outlined. The concept of a cooperative mining research program is presented. The improvement of performance through techno- logical developments and human skills may well be the greatest competitive edge available to the U.S. mining industry. In this regard, the need for new endeavors between industry and universities can hardly be overemphasized.

Jan 1, 1984

By W. H. Stahl

The continuous vacuum filtration is the solid-liquid separation process that is nowadays most frequently used in the beneficiation industry all over the world. After a development time of several decades, the various filter types such as drum filter, disk filter, plate filter and belt filter can be consideres as a sound functional design ensuring a trouble-free operation. Nevertheless, the vacuum filtration does no longer meet the present and future technological requirements. The moisture content of filter cakes is too high. Their thermal secondary drying is too expensive (coal, ores) and may bring about undesirable material changes and the filter cake conditioning with water-binding substances for dumping purposes is too costly.

Jan 1, 1983

By T. P. Meloy

Current coal cleaning technology uses heavy media (HM) for the recovery of coal in particles larger than 1/16 of an inch. Through the use of float sink measurements of the feed and products to commercial HM unit operations, a selection function, sometimes called Tromp curve in the coal industry, can be computed. Since the selection function is a plot f the probability of a particle appearing in the float versus the particle density, the slope of the curve will be sharper at the point where the particle has a 50% chance f appearing in the float. Thus, the separation will be better. Fine-tuning a unit operation or a circuit of unit operations requires that the selection function be accurately known. By current practice, it is difficult to obtain an accurate measure of the slope because, when the selection function is plotted versus density, the data forms an S-shaped curve which lacks data points near the 505 point of the curve. This lack of sensitivity in measuring the slope means that small recovery improvements cannot be detected; thus, only large improvements are measurable. Since most engineering improvements are small when individually considered, but large when aggregated ever many small improvements, this lack of measurement sensitivity rules out the slew march toward improved efficiency. This paper presents a method of analyzing heavy media selection functions resulting in a far more effective measure of the selective function slope. Furthermore, this improved method is applied to a number of industrial coal cleaning plants for both heavy media and heavy media cyclones. Using the work of Hudy (1968), and Deurbrouck and Hudy (1972), selection functions for individual unit operations in each plant are calculated as a function f particle size as well as density.

Jan 1, 1982

By A. J. Kwitowski

Remote control for mining machines ordinarily means the operator is not seated on the machine, but is located within direct view of the machine and work area Thus, remote control operators are exposed to the hazards of roof/rib falls and dust/methane explosions. The U.S. Bureau of Mines has developed a method to disassociate remote operators from these hazards. Off-board, computer-based "tele-operational" systems are utilized that station the operators one-hundred meters or more distant from the working faces. Details are provided for tele-operated systems for thin-seam extraction and haulage equipment in highwall and deep, room-and-pillar coal mines.

Jan 1, 1992

By Samuel S. Adams

The Grants uranium region of northwest New Mexico is the largest uranium district in the United States (approximately 50% of U.S. production plus reserves) and one of the largest In the world, with approximately 900 million pounds U308 production plus reserves. Deposits of the region are unusual among sandstone deposits for their high content of epigenetic carbonaceous material, generally interpreted but not proved to be of humic origin--that is, co-extensive with uranium in the primary deposits. Virtually all production in the region has been from the Jackpile Sandstone and Westwater Canyon Member of the Jurassic Morrison Formation. The tabular uranium deposits contain, in addition to humate and uranium, significant authigenic phyllosilicates, quartz overgrowths, humate-replaced detrital silicates, and a trace-metal assemblage typical of other sandstone uranium deposit types. Surrounding the deposits in the two sandstone units of the Morrison Formation is an alteration zone within which iron leaching has altered detrital ilmenite-magnetite to residual masses of titanium oxides. Feldspar alteration is locally present within this zone, below deposits in the Jackpile Sandstone, and above those in the Westwater Canyon Member. The feldspar alteration increases in inten¬sity toward the Brushy Basin Member which separates the two sandstone units, ranging from partial replacement to replacement and dissolution of plagioclase and sanidine. Spatial relations among the epigenetic humate, authigenic silicates, and the broad alteration zones that extend from the Brushy Basin Member to and including the uranium deposits suggest that (a) the organic material was involved in the unusual silicate alteration, transport, and authigenesis, and (b) that the humates originated in shales of the Brushy Basin Member. Stratigraphic relations among the Brushy Basin Member and the overlying Jackpile Sandstone and underlying Westwater Canyon Member suggest [in turn] that there was continuous, interfingering deposition controlled in part by contemporaneous basement subsidence along northwest- and northeast-trending zones. Following minor erosion of upper Jackpile Sandstone and deposition of basal organic-rich Cretaceous sediments, the silicates of the Jackpile Sandstone were once again altered by organic-bearing fluids, this time permeating down from Cretaceous sediments and partly obliterated ore-stage alteration.

Jan 1, 2013

By J. E. Moyle

Rio Algom Corporation of Wilmington, Delaware is a wholly owned subsidiary of Atlas Alloys Inc., an Ohio Corporation, which in turn is 100% owned by Rio Algom Mines Limited of Toronto, Canada. Rio Algom is controlled by the Rio Tinto Zinc Corporation of London, England, which has subsidiaries and affiliated operations throughout the world. Rio Algom geologists first became interested in this Utah pro- perty in 1966, after preliminary drilling had indicated that a known orebody close to the surface appeared to continue on the dorm thrust side of a major local fault, known as the Lisbon fault. Accordingly, in 1968, arrangements were made to acquire what was known as the "Humeca Option", a total of 2,573 acres located in San Juan county in south-east Utah, 35 miles south-east of the town of Moab.

Jan 1, 1975

By W. Z. Choi

A combined size reduction- liberation model of grinding has been developed to predict the product size distribution for both free and locked particles. The model is an extension of the population balance model for size reduction. Locked (or composite) particles have been subdivided into discrete classes of different compositions to obtain more detailed information. The model has been tested on a sphalerite ore from Tennessee. Liberation data have been obtained using an areal scanning technique on microscope images of polished particle mounts.

Jan 1, 1985

By Charles E. Robertson

As it becomes more and more apparent that our nation must place a great deal of reliance on coal as an energy source in the coming decades, prospecting for new reserves Un Missouri and other states in the Western Interior Region is increasing. As more and more of the known reserve becomes committed to existing or planned projects operators will be forced to look beyond the fringes of existing coal fields for additional reserves. Perplexing geologic problems invariably confront all prospectors and are particularly bothersome to those new to a particular area. It is the purpose of this paper to alert prospective operators to geologic problems likely to be encountered and to offer guidance in the recognition and solution of these problems. Particular emphasis is placed upon geologic structure and washouts. Other geologic problems have been discussed in a previous paper.

Jan 1, 1977

By Helmut Goehring

Surface mining has been used primarily where deposits of minerals were exposed or close to the surface. Surface mining can, therefore, be considered the oldest branch of mining. As the most accessible deposits became uneconomical because of the lack of suitable high capacity conveying systems, deep mining took its place. Only in the twentieth century was this trend reversed as high capacity production and conveying systems were developed. This rapid development was triggered by the steadily increasing demand for raw materials and fossil fuels, as well as by the ever increasing ratio between overburden and deposits.

Jan 1, 1982

By A. I. Johnson

This paper describes," the application, of a modular or building block approach to the analysis, design, and control of complex mineral treating processes. The main purpose of the paper is tutorial, to show the reader how such processes can be modeled using a modern digital computer" and, not to discuss in any detail the results that may be achieved in such studies. It is proposed that, the main techniques be illustrated by reference mainly to the Bayer process for alumina extraction and purification; in cooperation with the Aluminum Company of Canada Ltd. the author and his Colleagues at McMaster University and their students have studied this, process as a means of applying new computer techniques to extractive metallurgical processes. The plant described was studied by the author and his colleagues as a senior undergraduate project in cooperation with the Aluminum Company of Canada. It is one of several studies that have been carried out with Canadian industry. (1)

Jan 1, 1972