Search Documents

By James E. Breland

Society's growing concern over the number of deaths and serious injuries occurring in coal mines, coupled with a growing sentiment to develop and promulgate improved mandatory health or safety standards, was no doubt the basis for passage by Congress of the Federal Coal Mine Health and Safety Act of 1969, being Public Law 91-173 approved December 30, 1969. Even prior to passage of the Act, strong reaction was quick to arise concerning the effect of such legislation upon the coal mining industry. Initial response varied from mild forms of criticism to' the expressed fear of complete suspension of operations and mine closings. Primarily responsible for these early forms of skepticism were speculative or fanciful cost estimates which led operators to contemplate a less than prosperous existence. However, in spite of this unfavorable outlook, the majority of the operators have faced up to the situation and have been striving to comply with the Act and the regulations issued thereunder. While encouraging strides have been made toward implementation of the Act, it must be recognized that noticeable results have been attained only through many months of determined effort and, as anticipated, at quite heavy expense to the operator.

Jan 1, 1973

By D. E. Hart, A. R. Walsh, Derek Maishman

In order to safely construct a ventilation and escape shaft through saturated overburden into an operating mine, artificial ground freezing and raise boring were combined for the first time on a project in the U.S.A. at Georgia-Pacific's Kentwood Mine in Grand Rapids, Michigan. Previous to drilling a pilot hole 206 feet deep into the mine, a 20 foot diameter cylinder of soil 140 feet deep was totally frozen. Before termination of the freezing operation, the pilot hole was reamed to 9 foot diameter and a 7 foot inside diameter hydrostatic steel liner was grouted in place.

Jan 1, 1991

By Ellis J. Brien, O&apos

This afternoon I would like to talk to you about coal, its defi- nition, its constituents, its associated minerals and present and future coal preparation techniques. This discussion will be an attempt at presenting sufficient coal preparation and associated fundamentals to enable you to understand "deep cleaning", a more advanced beneficiation process which will be commercially practiced in the near future.

Jan 1, 1976

By J. Van Kleunen

In the Spring of 1959 the Riverside Cement Company, a Division of American Cement Corporation, placed into operation at their Oro Grande California plant a new crushing-blending-reclaiming facility. This new facility, in conjunction with other modernization in the plant, has established a degree of automation and reliability on a-plant-wide basis which heretofore had not been attained in the industry. The blending and reclaiming facilities for raw stone and cement clinker at this plant represent not only the first computer programmed materials handling system of its type in the industry, but also the first installation of specialized equipment which was designed for high capacity, fully automated operations.

Jan 1, 1963

By R. L. Atwood

This paper discusses the metallurgical and Manufacturing input to Merrill-Crowe plants. Topics treated are pregnant solution chemistry, clarification, degassing, zinc addition, product filtration, accounting, and costs.

Jan 1, 1985

By Dwayne C. Kicker, Duk-Won Park

As the use of longwall mining increases in the U.S.. there is a need to better understand the stress redistribu- tions indicative of this method. To control high stress concentrations, the yield pillar concept has been developed. A physical longwall mine model has been designed to study the effect of yield pillars in deep mining. The model in- cludes sensitive stress measuring devices, a new excavating technique, and a new model material. This study includes the use of both regular and yield pillar systems and has successfully simulated the mode of stress change in chain pillars.

Jan 1, 1986

By Joseph G. Wargo

The purpose of this paper is to investigate trends in exploration expenditures of a selected group of mining companies for the interval 1968 through 1971. The paper also compares these trends with other financial factors that are associated with various groups of companies and comments on the implications of these trends. Although a four-year interval is hardly enough time to establish a long-range set of trends from which operating rules can be derived, the fact that the four years selected are in the immediate past gives some sense of relevance to the matter of exploration expenditures at the present time and in the near future. The sample under study here consists of 21 mining companies. Of these, 19 are listed on the New York Stock Exchange and 2 are listed on the American Exchange. Twenty are American, one is Canadian. All are fundamentally "mining companies" in that they derive the bulk of their income from the extraction, sale, and at times, fabrication of metals from their own mines. This is in contrast to companies which have mineral exploration departments but derive the bulk of their revenues from sources other than mining; for example, from oil and gas sates, Also, no companies which can be considered strictly as exploration companies are included in this study. Although this definition held up fairly well when studying this list in 1968, the strict application of this definition became more difficult through the years up to the present time. In 1971, three or four of the companies were changing their character in that they were phasing out of the mining business, and either deriving their income or planning to derive a substantial part of their income from activities other than mining. A study of

Jan 1, 1973

By W. A. Weimer

Coal and coal mining is no longer the mighty king of industry and in our daily lives and homes that it once had the privilege of commanding. Many of you will remember that one of the chores of your youth was to bring in the scuttles of coal, morning and night, to feed the heater or stoke the furnace in the morning and bank it at bedtime. Growth of gas and oil have displaced coal in home furnaces and commercial buildings, and have taken over some segments of industrial markets. The coal burning locomotives have virtually disappeared in favor of the more efficient diesel engine. However, coal as a prime mover still holds its strategic position as is evidenced by act that the electric power industry almost entirely depends upon coal for its generation.

Jan 1, 1961

By J. D. Miller

The sedimentary western phosphate deposits of Idaho, Montana, Utah, and Wyoming tend to be calcareous and generally carry a significant amount of dolomite along with collophanite. In some cases, such as the Smokey Canyon Mine, Afton, Wyoming, the ore will also contain mudstone, and in this case the aluminosilicate minerals (clay, feldspar, etc.) together with some dolomite are floated from the collophanite in column flotation cells with an amine in order to meet product specifications (31 % P205) (Service et al.). In other cases, such as the SF Phosphates Limited Mine, Vernal, Utah, the ore is treated by traditional fatty acid flotation of the collophanite with mechanical flotation cells (Weber, 1986). Preliminary tests have now been conducted to evaluate air-sparged hydrocyclone (ASH) technology for the flotation of western phosphate ore. For this preliminary study, samples were taken from the hydrosizer overflow stream (18-21 % P205) at the SF Phosphates Limited Plant in Vernal, Utah for scavenger flotation testing with the 2-inch ASH system in laboratories at the University of Utah. Selected design and operating variables are being studied, and the initial results show that satisfactory separations can be achieved by high-capacity ASH flotation at appropriate operating conditions. For example, with single-stage ASH flotation 80% recovery can be obtained with a scavenger concentrate grade of about 26% P2O5. These results are comparable to, or better than, those obtained at SF plant operations with conventional flotation cells and suggest that ASH flotation technology can be used to good advantage in the phosphate industry. Of course, research should be continued to consider other process streams, optimize the separation efficiency, and evaluate larger diameter ASH units.

Jan 1, 1993

By E. P. Lunghofer

Silicon Carbide and Aluminum Oxide were two of the early forms of man-made abrasives often referred to as synthetic and were invented at the turn of the century. Edward G. Acheson invented Silicon Carbide in 1893 and Charles F. Jacobs filed a patent for the manufacture of fused alumina from bauxite in 1900. Jacobs' patent provided a method for tempering the alumina by reduction and fusion to a degree of hardness and toughness suitable for abrasive purposes. These two inventions are the basis of the synthetic abrasive industry today. Improvements have been made in the equipment used in the process, however the process itself remains basically the same. In 1904 A. C. Higgins observed that hot spots developed on the shell of the pot furnace used in the reduction of bauxite. He found that by spraying water on the hot spots they could be prevented and, in addition, they failed to return in the same place. Higgins reasoned that the cooling effect of the water caused the melt contacting the metal shell to freeze as an insulating autogenous refractory. This suggested that an improved furnace design could be obtained by using a metal shell which is continuously flooded with water on the exterior surface. Paradoxically, a furnace required to contain tons of molten Aluminun Oxide was thus constructed of nothing but a sheet steel shell with no refractory lining at all. A test of such an arrangement was tried by Higgins with considerable trepidation and was found to be extremely satisfactory.

Jan 1, 1985

By William F. White

It is a pleasure to have the opportunity of being here today to discuss the application of horizontal filters in the metallurgical industries. The use of horizontal type filters has been limited in metallurgical plants. However, in the recent past there have been new designs of this type equipment which greatly broaden their field of application. Through their use in many applications, important economies can be achieved over more conventional methods. The first of the modern continuous horizontal filters was initially developed by Oliver United Filters as their scroll type horizontal filter. This was an outgrowth of the old Oliver Sand Table that was limited to very coarse, free filtering pulps containing no appreciable amount of fine particles. The sand table was rather limited in application. The later continuous scroll type horizontal filter provided for a reverse air blow after discharge which reslurried the heel remaining and permitted the filtration of pulps containing finer particles. In the manufacture of phosphoric acid by the ?wet? process, the filtration of gypsum from the strong acid presented an extremely difficult filtration problem due to blinding of the filter media caused by crystallization of the soluble salts contained in the acid. A filter which allowed for continuous cloth washing was required, and this led to the development of the continuous pan type, and travelling belt type horizontal filters which provided for this need. Among the filters developed were the Prayon by Engineering and Industrial Corporation of Luxembomg for use in their phosphoric acid plants. They are one of the largest manufacturers of phosphoric acid in Europe. The Dorr-Oliver Traveling Pan Filter was also developed by Mario Giorgini, Manager of Dorr-Oliver?s Italian subsidiary, for use with the Dorr Company?s phosphoric acid process. Basically, there are four existing types of horizontal filters in commercial use at this time: The scroll discharge non-pan type, the continuous belt type (Lurgi), rotary pan type, and the traveling belt type. The construction and principle of operation of these various filters will be discussed.

Jan 1, 1958

By Robert M. Cox

Systematic roof bolting has proven to be a very effective method of mine roof control; however, major roof failures still occur and roof falls still remain the number one occupational hazard of underground miners. Why do some bolted mine roofs fail, while the vast majority of bolted mine roof remains stable and safe to work under? Observations of numerous roof failures indicate that most of the major roof failures* are associated with either: 1) Jointing, faulting or other structural fracture zones; 2) massive shale beds of lenticular structure, or 3) thinly laminated sand-shales. The jointing and faulting present an obvious weakness in the roof rock structure; whereas, the massive shales and laminated sandy-shales create a roof structure with low shear strength and/or modulus of deformation. An observation of major significance is that most bolted mine roofs fail as a unit, and that the thickness of the fall is roughly equivalent to the roof bolt length (See Figure 1). In fact, several operators have experienced the phenomenon of an increase in roof fall thickness with an increase in roof bolt length.

Jan 1, 1973

By R. D. Call

During the past fifteen years considerable progress has been made in the technology of slope design. It is possible to design rational slope angles if suitable data on geology, hydrology, and rock properties are available. It is of course preferable to conduct a full scale slope design study, but there are those situations where a full scale study is not feasible because of time and budget constraints. In this paper we will treat two situations: (1) choosing slope angles for a preliminary feasibility study at the exploration stage; and (2) dealing with a slope failure in an operating pit. In these instances slope angles must often be chosen on the basis of available or readily obtained data. In an exploration program all too often a feasibility study is initiates just a few months prior to the decision deadline to drop the property or to exercise an expensive purchase option. If all that is available at this point are a few cross sections at odd angles showing ore and waste contacts and a dog-earred map of the surface geology there may not be time to collect and organize enough information for design of slope angles. On the other hand if during the drilling program geologic cross sections are constructed and the structural data is presented in tabular form, rational slope angles can be determined within the allotted time. Certain types of data can be collected only at specific times during a project. Two prime examples are logging fracture intensity and collecting samples for rock testing before the core is split. It is particularly disheartening to ask to see the core and to be shown a tattered cardboard box filled with plastic bags of sample pulps.

Jan 1, 1976

By Kirk Conway, Richard L. Unger

The U. S. Bureau of Mines conducted a research project to analyze the design of underground mining equipment with respect to ease of maintenance and maintainer safety. The work included a review of maintainability design literature, an analysis of maintenance related accident data, field reviews of equipment designs, and interviews with mine maintenance personnel and equipment manufacturers. Based on the findings, a set of maintainability design recommendations have been prepared. The final recommendations document includes maintainability engineering information for equipment designers, as well as a buyers' guide to aid purchasers of mining machinery in evaluating the maintainability of equipment.

Jan 1, 1992

By Stephen Hodgson, Ken Brouwer

September 2005, Northern Dynasty Mines announced the discovery of a new, high-grade deposit at its Pebble project in southwest Alaska. The product of insightful geological investigation, Pebble East, as it is now known, is quickly growing into one of the most significant copper deposits in the world. Preliminary analysis shows it could reduce the U.S. copper supply deficit by a third. The new deposit has also altered Northern Dynasty’s view of how Pebble should be developed. This article describes the Pebble project as it is currently understood and outlines the work planned for the next several years.

Jan 1, 2007

By Kimberley MacHardy, Ann Maest, Greg Lawson, James Kuipers

Although water quality predictions are often made in Environmental Impact Statements (EIS's) as part of the National Environmental Policy Act (NEPA), comparisons between predicted and actual water quality conditions are rarely reviewed. A comprehensive review of predicted and actual water quality conditions was conducted for a number of large U.S. hardrock mines with EIS’s. For mines with large differences between predicted and actual conditions, factors responsible for the deviations, such as characterization and modeling errors or engineering failures, were identified. Recommendations are made for how the NEPA process could be modified to better predict water quality at hardrock mine sites.

Jan 1, 2005

By Karin Bäppler

A new polyhalite fertilizer mine is currently being developed in the UK by Anglo American Crop Nutrients. The project includes the construction of a Mineral Transport Tunnel almost 37 kms long to house a conveyor belt that will move polyhalite from the production shaft at the mine to a materials handling facility at the port. The project sets a new standard in terms of an ultra-long tunnel drive and sustainable, environmentally friendly and efcient material transport. The paper highlights in particular the . m diameter TBM in use for the construction of the ultra-long tunnelling section.

Jun 23, 2024

By Richard M. Crowell, Laurie M. Tahija, Keith D. Dagel

Echo Bay Mines Ltd. operates a gold heap leach in Round Mountain, Nevada, U.S.A. In the past two years, the mine has expanded operations from 13.5 kt/d (15 kst/d) to 41.0 kt/d (45 kst/d), making it the world's largest gold heap leach operation. The expansion is a separate system from the previous 12 year old plant, yet very similar. The flowsheet contains open circuit primary, secondary, and tertiary crushing with interstage screening. A leach pad stacker loads reusable asphalt leach pads. The process plant features carbon adsorption, pressure strip, electrowinning, and electrorefining.

Jan 1, 1990

By S. A. Braley

Water is our most important natural resource, for without it there is no life. It is also the principal natural resource for all manufacturing processes, in particular for the development of power. For these reasons it is essential that water be protected and conserved, with the realization that its quality 18 as important as the water itself. A significant factor in the quality of ground water is the mining of coal -- that other main ingredient of Power. In the mining of coal it is necessary to disturb the geological strata overlying or adjacent to the coal seam. This procedure not only releases water from water-bearing strata or underground aquifers but also exposes other minerals which eventually become the source of pollution or deterioration of the released water as well as of the surface stream into which It is discharged It is then evident that in attempting to utilize one essential natural resource there is degradation of the quality of the other. Many selfishly assume that the principal function of a stream is fishing and recreation, but the real function is the support of industry and agriculture upon which civilization is dependent.

Jan 1, 1959

By D. Loy LeRoy

As we are all aware, the impacts of the 1977 Surface Mining Act and the implementing OSM Regulations require application of new, as well as existing, equipment and technologies. Our firm recently completed (June, 1979) a study for the Department of Energy titled "Analysis of the Impact of Public Law 95-87 on Mining Performance." The objective of the study was to analyze the impact of the Act and its regulations on mining performance in order to provide recommendations to alleviate the impacts identified, including identification of research needs. This paper presents some of the highlights of that report: projected cost increases; additional equipment needed for compliance; review of methods currently practiced or those which can be modified; and will focus particulary on equipment and technology applications.

Jan 1, 1980