Search Documents

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016

By Gregory P. White

A number of private companies and universities have developed computer programs which can be used to simulate surface coal mining by dragline. In this paper, we briefly discuss the concept of computer simulation, compare these computer programs with each other, describe the major changes required to convert these programs to an IBM computer system, and analyze their sensitivity to inaccurate input data. We also present a summary of the required data input for each program, core storage requirements, and output results. Sources for obtaining these programs and their documentation are listed at the end of the paper.

Jan 1, 1983

By Kapila Pathirage, Michael S. Schultz, Gregory Sanders, Ulf G. Gwildis

Adequate understanding of the subsurface conditions along the alignment of a planned tunnel is key for managing project risk. For achieving this understanding, geotechnical borings are conducted during design. Where their spacing cannot reduce the risk of encountering differing site conditions (DSC) in-between borings to an acceptable level, supplemental exploration methodologies or data evaluation approaches may be required to bridge the data gap. This paper compares the exploration design approaches of recent tunnel boring machine (TBM) and microtunnel boring machine (MTBM) projects in the quaternary deposits along the Eastern Seaboard, the glacial geology of the Pacific Northwest, the sedimentary rocks of the South, and metamorphic rocks in western Germany, describing their respective effectiveness of managing DSC risk.

Dec 1, 2022

By J. Andrew Leach, Robert T. Tape, Thomas G. Harper

A practical approach to elope stability design of heap leaches up to 90 m (300 ft) high is presented based on recent experiences with heaps throughout the Western U.S. Shear strength parameters for foundations, ore and liner systems are considered, with particular attention given to frictional contacts between geomembranes and clay or geotextiles. Stability of both ore and containment dikes is discussed including the effects of seismicity, staged dike construction, progressive heap development and in-heap solution levels. Design criteria and methods of analyses are presented along with techniques for improving stability.

Jan 1, 1987

By J. R. Johanson

In recent years the procedures for functionally designing bulk storage bins and hoppers have evolved from qualitative guess and try methods to a quantative method based on theory and tests of the bulk solid to be stored. This quantative method, developed and implemented by Dr.'s A. W. Jenike and J. R. Johanson as with any new design, must prove its effectiveness and validity in the actual operation of the finished equipment. How accurate are the theoretical predictions? Is it possible to extrapolate from bench size tests on a small ample of the bulk solid to the full scale bin design? Can the theoretical designs be economically translated into working hardware? In this paper the answers to these questions are discussed in light of actual bin operations.

Jan 1, 1968

By George Mandarakas, Johan van Zyl, Karl-Heinz Becker

The world’s climate today has changed compared to 10 or 20 years ago. Many countries face water shortages; water sourcing for mining activities has become harder to secure. ESG’s focus on the industry has made us more aware of the need to preserve and responsibly use the water needed for wet processing in our milling and sorting activities. In a recent greenfield project in South Australia, 10 Gigalitres per annum would be required to process 5Mtpa of magnetite [1]. Published information indicates that the mining industry consumes approximately 12 EJ per year—or 3.5% of total global final energy consumption globally [2] or 3.33 trillion kilowatt hrs. This energy consumption is significant, considering the critical role mining plays in extracting and processing essential minerals for economic development and human progress. The perception of the mining industry is that not only does it consume significant power, but it also consumes a lot of the freshwater in the world. In fact, it consumes approximately 5% [3] of the total freshwater demand. According to the Intergovernmental Panel on Climate Change (IPCC), by 2050, 60% of the world’s population will be living in countries that are classed as water-stressed [3]. As more and more emphasis is placed on renewable energy sources, the amount of water used in mineral processing will increase because more and more raw materials require a water-intensive process. This increases the pressure on the mining industry to try and find water-saving initiatives. As part of this review, recent advancements in magnets have enabled magnetite processing facilities to achieve between 30 to 40% dry gangue material rejection before the wet beneficiation process (grinding and sorting). This reduction in energy consumption allows the reduction of energy consumption. Secondly, there is less material ground in the mills, which requires less water for mineral downstream processing.

Feb 1, 2025

By Karl A. Olsson

The Glenharold Mine is a surface mine operated by Consolidation Coal Company. The mine is located approximately 90 kilometers (55 miles) northwest of Bismarck, and 3 kilometers (2 miles) southeast of Stanton in west central North Dakota. Glenharold has a nominal design capacity of 3.0 million metric tons per year (3.3 million short tons per year). With the exception of local coal sales, this production supplies fuel for Basin Electric's Leland Olds generating station, a mine mouth power plant. The mine has 175 hourly and 50 salary employees. The Glenharold reserve extends over 210 square kilometers (80 square miles). The mining area is on a dissected plateau between the broad flat Missouri River flood plain to the north and the gently rolling uplands to the south. Erosion by intermittently flowing streams has produced many narrow, steep-walled, drainage ways. Mining begins at the 6 meter (20 foot) cover line and continues to the economic recovery line.

Jan 1, 1982

By Y. Lizotte

The purpose of this paper is to describe a stochastic simulation program used to assess several dispatching rules applicable to small scale computerized systems for optimizing truck/shovel productivity. The system studied is semi-automated with a dispatcher communicating instructions by two-way radio. The simulation program is structured on an advance clock approach which enables the insertion of dispatching rules at various points in the haulage net- work. The rules tested include minimize shovel idle time, maximizing immediate truck use and assigning trucks to shovels to meet specific production objectives. A variation of the traditional "Match Factor" is implemented to maintain fleet balance throughout the shift. A mine case study demonstrates how the dispatching rules increase productivity of such semi-automated dispatching systems. Practical problems involved in the implementation of small computerized dispatching systems are also discussed.

Jan 1, 1986

By Philip Lindstrom

Retreat mining, using yielding steel friction props, over a seven-year period has been successful at a uranium mine operated by Hecla Mining Company in southeast Utah. The support system allow good roof control, maximum profit, complete extraction, and good ventilation. Unusual subsidence observations were made in that some of the surface was raised rather than lowered, Longwall mining, commonly practiced in European coal mines, has a potential of broader application because of mechanization possibilities and better roof control and ventilation at greater depths.

Jan 1, 1964

By Horst H. Gielen

Bong Mining Company/Liberia provides the rare opportunity to compare two generations of grate kiln pelletizing plants operating on the same magnetite/hematite ore basis. In this paper advantages and drawbacks are compared: mechanical aspects, energy-savings, pellet quality. Plant I with up- and down-draft drying gas flow. Plant II runs only on down draft drying and incorporates a heat-recoup system. Ferteco Mineracao/Brazil operates a Lurgi straight grate plant since 1977 on hematitic pelletfeed. Energy-political situation and char- coal as energy source in Brazil are reflected also in the search for alternative fuels for pelletizing. First measures and results are reported as well as intended further steps towards a 100 % oil replacement.

Jan 1, 1983

By J. Wyn Prior

The seismic refraction technique is probably the most popular geophysical method of bedrock profiling in geotechnical site investigations but is somewhat restricted by the inherent assumptions in the method. This paper describes how Hales' method of profile interpretation is modified to overcome the assumptions of increasing velocity and layer thickness with depth when only first arrival data is available. A further expansion of Hales method enables presentation of refraction data in a form whereby bedrock features, such as changes in velocity, relief and dip in particular, are more readily recognized. Characteristic curves of the more common bedrock features are presented as an aid to bedrock feature recognition.

Jan 1, 1976

By William H. Lehr

In recent years, we have witnessed many innovations in the equipment used in handling bulk materials. Not too long ago, any sizeable stockpile of coal or iron ore was attended by one or more material handling bridges. More recently, large stockpiles have been built with mobile equipment of' the earth moving type with bulldozers and front end Loaders being utilized in reclaiming operations. The most recent stocking and reclaiming device is the rotary bucket wheel machine. The early bucket wheel machines built in the United States were developed for the strip mining of coal. We understand that the first American machine was built in the Midwest in 1944. This type of unit was developed in an effort to reduce the cost of removing overburden and to provide satisfactory spoil disposal. As the available coal reserves under shallow cover were exhausted, the cost of removing the deeper overburden with conventional equipment became too great for these operations to continue profitably. The first machine has now been followed by six or seven additional units, the largest of which can handle material at a rate of more than 7000 cubic yards per hour.

Jan 1, 1965

By Om P. Garg

The purpose of this paper is: 1) To summarize the capabilities and some of the limitations of the existing mine planning software. 2) To provide some guidelines for acquiring the software. 3) To identify problems and challenges in terms of how to justify increased use of computers (particularly the 32-bit microprocessor based super micro computers), for various activities related to a mining operation No attempt has been made to review the contents of available software packages in detail. Also the scope of this paper is limited to mine planning related computer applications. Applications related to accounting, inventory control, preventive maintenance, equipment scheduling, etc. have not been covered.

Jan 1, 1983

By Robert F. Droullard

The U. S. Bureau of Mines (USBM) has investigated instrumentation and methods for measuring exposure to radon daughters in underground mine atmospheres. Both personal and area monitors have been studied through in-house and contract research. A field study in uranium mines identified some reliability problems that required additional work for the personal dosimeter systems. Improved versions of continuous working level detectors have been developed and tested for use as area monitors in underground mines. Test results for the personal and area monitors were satisfactory for underground mine applications.

Jan 1, 1981

By Bernard A. Kilgore

Kaolin is a hydrated aluminum silicate mined primarily in middle Georgia along the "fall line", the location of the coast line in prehistoric times. It is used extensively as a filler for paper, insecticides, tires, plastics, a pigment for paints, as a coating for fine gloss paper, and for high grade ceramic products, such as catalytic converters. During its journey from the open pit mine to its final use, kaolin takes many forms, and must be handled in many different ways. The purpose of this presentation is to follow kaolin through its process and briefly describe some of the methods Georgia Kaolin Company, one of the world's largest kaolin producers, uses to handle and convey its product and some of the peculiarities involved.

Jan 1, 1983

By Alan J. Michaels

The paper addresses the problem of the high costs of accidents ad how AMAX Inc. - a diversified natural resources company - has managed to control its losses through a tri-thrusted approach of: (1) management commitment, (2) methods of implementation that are tailored to each division or local unit, and (3) a reward system for outstanding performance. Specific attention is focused on the Corporate Loss Prevention Department's "10 Point Program for Loss Prevention Management".

Jan 1, 1981

By Kent D. Gastreich

As the number of prime surface coal mining sites diminishes with time and with the potential for increased coal demand, areas that were previously not mined because of their difficult mining conditions, marginal economics, and controversial environmental nature, will have to be considered if surface coal mining is to continue in the future. Such sites include areas near major rivers, streams, and lakes. The name most commonly given to these areas by regulatory agencies is "wetlands". The exact definition(s) to the term "wetland" will be discussed later in this paper. Most coal operators are now more than familiar with permitting requirements under the Surface Mining Control and Reclamation Act of 1977 (SMCRA). The SMCRA permanent regulatory program recognizes the fact that coal mining operations will periodically encounter streams, wetlands, etc. Although discussed in various sections of the permanent program regulations, the relationship of coal mining operations to wetlands is particularly evident in the performance standards regarding hydrologic balance and protection of fish, wildlife and related environmental values.

Jan 1, 1980

By Earl A. Berry

Someone once said, "The safest mine is one in which no one goes into." We all recognize this as being perhaps wishful thinking. We also recognize in it a certain amount of truth and an ultimate goal if we are optimistic. All of us are aware of the many things that have been done, are being done and will be done to reduce manpower in mining. For those of us; who are optimistic about this ultimate goal it would appear from the records-we are more than well on our way to the so called safest mine. Let us see what has been done in the past 20 years. T e period from 1935 to 1956. For example in the coal mining industry: In 1935 there were employed 462,903 men who produced an average of 805 tons per man per year or 4.50 tons per man per day. In 1955 there were employed 225,093 men who produced an average of 2,064 tons per man per year or 9.84 tons per man per day. There are no comparable figures compiled for the metal mining industry as a whole that can be broken down in this manner. However, from examination of figures available for different groups in metal mining there is a trend similar to that in coal mining. No-dbout the above figures reflect the intense development and perfection of machines and mining systems to tear out, transport and process our mineral wealth. The figures also show the mining industry has been able to double its production and at the same time reduce its manpower by half. When you compare the number of men employed today with the number which would have been employed 20 years ago to gain todays production at that time it become apparent that greater safety has been accomplished. For example the years 1935 to 1956 for all mining show. In 1935 there were approximately 649,226 men employed in mining and reports show 1,399 fatalities and 74,913 non-fatal injuries. In 1955 when there were 313,883 men employed in mining 496 fatalities and 25,365 non-fatal injuries were reported. To have produced the same tonnage of material in 1935 that was produced in 1955 it would have required the employment of approximately 1,298,452 men. 2,798 could have been fatalities and 149,826 could have had non-fatal injuries. You can now measure the full impact of what has been accomplished in the past 2o years by the aggressiveness of mine management, the wizardry of our engineering personnel and the thoughtfulness and devotion of our safety people and their programs. Therefore, there is a trend towards the goal of our opening statement. We whoare toptimistic believe this trend will accelerate at a-faster pace. Why? Because anyone engaged in the mining industry today can well afford to invest a minimum of $30,000.00 in capital equipment todisplace the labor of one man. This fact alone is a terrific incentive for mine management to apply and manufacturers to develop equipment of a type to get the men out of the mine. Now you can determine this problem not only becomes one of safety but also one of economics, When productivity is stepped up and manpower reduced management is learning the hard way what it means to them; in the profit and los s column when a few minutes of delay or downtime of costly machines and processes occur. They have learned that fast and efficient communication systems are the best means of combating breakdown, delays, bottlenecks, supply problems, the saving of lives and property and increasing production. One large western metal mine was able to increase Its tonnage by 4000 tons a day by using modernup to date electronic type communication system. The National Coal Board of Great Britain recently allocated 45,000,000.00 to study and develop faster and more efficient communications when a survey indicated what a serious bottleneck poor communication in their present systems of mining turned' out Lobe.

Jan 1, 1958

By M. S. Davis

The Tek Process can produce masonry products such as bricks, roof or wall tiles, and block from virtually any inorganic waste. In the process the aggregate raw materials, portland cement, water and common chemicals are first mixed together; then mechanically subjected to several thousand pound pressure per square inch. This causes a novel chemical reaction between the cement, chemicals and water; producing the "patented" Tek adhesive binder which holds the aggregate together in a stone-like mix. Simultaneously, the desired product shape is formed. The building modules can have strengths of 8000 p.s.i. (pounds per square inch) with completely sound aggregates utilizing air curing for a period of 28 days. With most aggregates, 3000 p.s.i. is achieved within 24 hours. Eventual strengths usually exceed 5000 p.s.i. with almost any raw material. Water absorption ranges from 5-7.5 percent. Both absorption and strength figures are superior to the most rigid of any and all A.S.T.M. specifications for the highest quality bricks. In most locations, the product (when brick shaped is called Tekbrik) can be produced significantly more economically than can comparable grades of clay or other bricks, be- cause almost any inorganic waste materials or pollutant can be used as a raw material. The process results in a lower manufacturing cost as compared to clay bricks; fuel cost to operate a clay kiln represents a substantial portion of the total cost. Capital expenditure for a Tek plant also is lower due to the large investment in clay kilns. Transportation savings also are important, clay brick factories must be very large because the kilns are uneconomical unless they are large. Most bricks are manufactured at the sites of clay deposits in relatively uninhabited areas. The cost of transportation to the job site represents a considerable percentage of the selling price.

Jan 1, 1974

By K. Whiting

In October 1993, the first two of a series of full scale passive biological treatment cells were constructed to treat mine drainage from the Burleigh Mine (located approximately 48 km west of Denver, Colorado in the Clear Creek/Central City Superfund Site). The two cells are each 19-21 m long, 10.7 m wide and 1.2 m deep. Each cell contains approximately 216 cubic meters of substrate (composted manure) and is designed to treat 60 L/min of mine flow. One cell is designed as an upflow reactor and the other cell is designed as a downflow reactor. The differences in flow hydraulics and treatment efficiencies will be tested in these two cell for approximately nine months before the remaining cells are built to treat all the discharge. The substrate material was selected based on a series of bench scale tests. During the tests, the amount of metals removed was determined. The design flow rate was based on a sulfide generation rate of 400 nanomoles of sulfide generated per cubic centimeter of substrate per day. Metal removal results for the first three months of operation of the two cells will be presented and compared to results of bench and pilot studies at other sites.

Jan 1, 1994