Search Documents

By Leslie E. Apodaca

INTRODTUCTION The use of spiral concentrators for processing fine coal particles is an old idea that has recently gained acceptance in the 11.S. coal industry. It was not onti1 the Australian Minerals Industry developed a spiral concentrator specifically for separating coal from ash in the latter 1970's and early 1980's that spiral concentrators were seriously considered as viable equipment for processing fine coal. The Wright Coal Spiral was introduced in 1980, the Mineral Deposits Limited Mark 10 Coal Spiral was introduced in 1982, and the Vickers Wyong Coal Spiral was introduced in the latter part of 1984. Each spiral design was different and utilized constant profile troughs, constant pitch troughs, compound profile troughs, and various splitter arrangements. Mineral Deposits Limited has combined the best features of the compound profile trough and constant pitch trough with critically-placed splitters to develop the MDL LD4 spiral concentrator which is a truly efficient coal washing spiral. This spiral concentrator was introduced into the U.S. Coal Industry in 1987. Recently, Mineral Engineering Technology of the United Kingdom and Multotec of South Africa have introduced their own coal spiral designs. Spiral concentrators were first installed in fine coal processing circuits in the Australian, South African, and Canadian Coal Industries in the early 1980's and in the U.S. Coal Industry in 1985. SPIRAL CONCENTRATOR SEPARATION PROCESS The separation process that occurs within the spiral concentrator trough is very complex, as it is a combination of three gravity separation processes. When the coal slurry first enters the spiral trough, each coal and ash particle and the water is subjected to centrifugal forces. These forces cause the water, light coal particles, fine heavy ash particles, and medium middlings particles to the outer vertical portion of the spiral trough. The coarse ash particles and the coarse middling particles remain on the inside of the spiral trough. The center or transitional area of the trough contains a mixture of middlings particles and near-gravity material that is present in the slurry, as shown in Figure 1. At the same time the coal and ash particles are suhjected to centrifugal forces, the trough design (both profile and pitch) causes the particles to be subjected to flowing film and stratified bed separations. The combination of these three separations, whose efficiency is dictated by the spiral troogh design, will effect the separation of the lighter coal particles from the heavier ash and middlings particles. As the slurry flows down the spiral, the profile and pitch design of the trough will counteract the centrifugal forces on the fine, heavy ash particles and fine middlings particles and cause them to migrate from the vertical portion of the trough to the center or inner portion of the trough. At the same time, any heavy particles trapped in the transitional area of the trough will be forced to migrate to the inner edge of the trough and any coal particles will be forced to migrate to the outer edge of the trough. SPIRAL SPLI'TTEP ARRANGEMENT The critical placement of splitters along the inner edge of the trough for removal of the heavy ash particles as the slurry flows down the trough further enhances the separation of the coal particles. At the bottom of the spiral trough are product splitters arranged to make a final separation of the slurry stream into clean coal, middlings, and refuse products.

Jan 1, 1988

By S. Wegerer, M. Semel

The search for minerals typically starts with a reconnaissance phase. After finding a promising target area, further prospecting work will be conducted. Finally with growing confidence of having encountered an ore deposit with commercially viable concentrations of relevant minerals, an extensive exploration campaign will verify its potential. Best practice and reliable, efficient tools for mineral resource estimation of massive sulfide deposits in the deep sea have to be established yet. Therefore, a new seabed exploration system is in development. Various challenges are caused by the extreme environmental conditions in the deep sea and by the nature of massive sulfide deposits. Information of past and ongoing expeditions were gathered to form the basis of an in-depth requirement analysis. System functions and corresponding process times were derived. The experience from the existing MeBo seabed drill rigs serve as starting point for the concept study and following development. Initial MeBo system was built for maritime research purposes and now has to be converted into a new design, suitable for efficient and economic resource exploration. The new system configuration is modular structured to adapt easily to different application scenarios and challenges. To achieve an extension of the deployment depths, the overall equipment weight has to be limited through light weight construction and material. The drilling module contains a range of geotechnical coring tools to face the varying soil conditions of heterogeneous massive sulfide formations. The major challenge to overcome is the touch down sequence on uneven, 25° inclined, rough terrain in up to 4.000 m water depth. Furthermore, high precision of the final unit positioning is necessary. Landing sub-system proof of concept is validated in laboratory environment with small scale model. A novel seabed exploration system capable to land and operate safely on highly inclined slopes of mineral deposit is described. Obtaining high quality samples by wire-line coring technique is the objective.

Feb 22, 2026

By B. T. Field

Pyroprocessing systems range from low temperature dryers to high temperature reactors. The materials and process requirements cover a broad spectrum. It is not the intent of this paper to do a detailed examination of individual processes and equipment, since that can be found in a multitude of other sources; rather it is the intent of this paper to examine the key process variables and offer empirical guidelines to assist in a user?s overall evaluation.

Jan 1, 1998

When overburden depth exceeds economical recovery in openpit coal mines, the use of highwall mining systems has increasingly come into play. However, stability in the highwalls is always a major safety concern during such mining. The U.S. Mine Safety and Health Administration requires that highwall mining operators follow ground control plans that specify the pillar sizes necessary to prevent collapse that would threaten highwall stability.

Jan 1, 2006

By Earl Gardiner, Michael Grenier, Stephen Hardcastle, John Vergunst

A prototype, self-contained mine refuge station air supply sys- tem was tested in an underground metal mine to verify it's ability to keep oxygen and catbon dioxide levels at acceptable concentrations in an emergency situation. In this test, 25 volunteers were assembled and sealed in a functional underground refuge station for a period of 24 hours, without the benefit of the standard com- pressed air supply. The prototype system was designed to: 1) operate on a self-contained power supply for a period of at least 27 hours; 2) supply oxygen at a metered rate; and 3) remove car- bon dioxide by re-circulating refuge station air through soda lime scrubbing beds. During the test period, the catbon dioxide concentration remained at an average of 2500ppm and oxygen concentration stayed between 20.2% and 20.6%. The volunteers found the prototype easy to use and seemed confident in its ability to provide a safe atmosphere. The test showed that this technology could become part of an underground mine's refuge station emergency equipment.

Jan 1, 1997

By Zoltan F. Oszter

Feeding bulk solids from bins or bunkers sometimes poses a problem to the materials handling engineer. The paper describes, by practical examples, how material flow can be improved on existing installations, and how difficult-to-handle materials can be successfully drawn from storage and fed to fully automated process systems. The examples illustrated are based on actual experience with projects designed for the mining and metallurgical industry. Maintenance costs, where available, are also indicated.

Jan 1, 1966

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Gas holdup profiles in the collection zones of a pilot flotation column (0.91 m x 13.5 m) and a laboratory flotation column (0.057 m x 9.5 m) operated with air and water only were determined from pressure measurements. The profiles were determined discretely and continuously. For the pilot column, a minimum distance between pressure measurements was necessary to give reliable results. For the laboratory column, a third-degree polynomial fit to the pressure vs. height data was required. Water manometers proved to be less sensitive to sensor and process noise than pressure transducers. The profiles showed that gas holdup approximately doubled over a height of 8 to 10 m. The profiles were not linear, and the gradient increased towards the top of the column, especially for gas rates greater than 1 cm/s. The profiles cannot be predicted by a simple bubble expansion model. The implications of this new finding of a significant gas holdup increase with height in the collection zone on various aspects of flotation column design and operation are discussed.

Jan 1, 1996

By J. P. Ramsey

This is a description of the efforts of a research project intended to demonstrate methods of alleviating pollution from coal mine refuse piles and slurry lagoons. These are mainly derelict barren sites. Some are burning and some are vulnerable to wind erosion which causes air pollution. Some occupy valuable land near metropolitan areas. They are an integral part of the landscape of the Appalachian and Midwestern Coal Fields. They are important in the light of growing civic awareness of the great general problem of waste disposal and environmental improvement. In the V-shaped valleys of the Pocahontas Region, they continue to be piled higher and higher. In flatter topography, they tend to form broad, flat ridges. Some contain more metal forms than others and some have a minimum of metal, but weather to a fine talc, which chokes streams with a fine particle suspension. Most are burning or have burned, but burning or weathering, most all are sources of pollution to the atmosphere and to adjacent waterways. This demonstration project is being carried out at an abandoned mine near the town of Du Quoin in southern Illinois. It is jointly sponsored by the Truax-Traer Division of Consolidation Coal Company and by the Federal Water Pollution Control Administration of the Department of the Interior. The site area is a refuse pile and slurry lagoon, each of fifty acres. It is hoped that basic data from this study will be generally applicable to other sites and will provide a basis for rational and efficient engineering design of future reclamation projects. Most refuse piles have extremely long term capabilities to produce highly potent acidogenic oxidation products typifying the more serious aspects of acid mine drainage contamination. Numerous sites remain where the abandoned mine no longer discharges acid waters, but its associated refuse pile continues to generate significant quantities of acid and other oxidation products even after many years.

Jan 1, 1969

By F. L. Jackson

When using perlite as an insulation, it is important to determine the requirements for different applications as this influences the processing of the perlite. In cryogenic applications, perlite properties of low density and fine particle size are desirable, while Loose fill insulation applications require similar properties and water repellency. However, in perlite insulating concrete applications, a coarser particle, of higher density, is required to provide improved compression strength. The essential properties of perlite including, particle size, density and surface treatment are discussed in relation to the various insulation applications. Also typical mineral processing and manufacturing techniques are reviewed

Jan 1, 1983

By Allan M. Johnson

The Sherwood Mine is being monitored to determine the nature and extent of changes in the mine and its environs which result from the closing and the cessation of pumping. Of particular interest was the possibility of piping-induced subsidence occurring as the mine flooded. Previous experience in the district indicated that this possibility was very real. A monitoring system, including acoustic sensors, extensometers, surface subsidence monuments, and ground water observation wells was installed in July 1978, just prior to the mine closing. Late in 1979, three piping-induced subsidence events occurred. The monitored data, and related laboratory studies are being applied to a quantitative description of piping-induced subsidence.

Jan 1, 1980

By A J. Jonaitis

The DENVER Tube Press is a simple, high pressure (1500 PSI (100 bar» filtration unit, developed for processing difficult-to-dewater materials and to produce a handleable filter cake and clear filtrate product. Lab and pilot testwork conducted in Australia on coal fines (55-70\ -35 micron (400 mesh)) have shown that total moisture contents of less than 20\ are consistently achieved in the final cake products from the Tube Press. Currently, these coal super fines are sent to waste due to uneconomical mechanical dewatering methods, which were only able to reduce total moisture levels in excess of 30%. Calculated, throughput rates for the 500 Series Tube Press exceeded 1700 kg/hr (3750 lbs/hr). Feed solids concentration requirements are between 45 and 50\ to achieve these results.

Jan 1, 1993

By A. Noble

"Linear circuit analysis (LCA) is a fundamental tool that may be used to evaluate, design and improve the performance of mineral separation. The traditional LCA methodology provides a comparative evaluation of circuit designs purely from the unit interconnections. The quantitative approach uses the analytical circuit solution to evaluate the slope of the circuit’s partition curve at the midpoint. Since the partition slope is often associated with a separation’s general selectivity, this numeric value is used to compare and rank alternative configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. By itself, this value does not account for the relatively high unit dollar value of pure material or the gains and losses in mass yield associated with alternative circuit configurations. Realizing the value in the LCA methodology, but respecting the limitations of the partition slope valuation, the authors have derived two new performance indicators that quantitatively address pure particle misplacement (the Partition Moment of Inertia) and circuit mass yield (the Yield Score). Together, these parameters provide a better indication of separation economics in typical mineral and coal separation systems. Since the two parameters provide independent information on circuit selectivity and circuit yield, a Pareto efficiency, multi-objective function selection approach is proposed for preliminary circuit selection.IntroductionOver the past 30 years, numerous scientific and industrial studies have proposed various mineral processing circuit design methodologies that attempt to optimize the allocation of separation resources within the processing plant. Over this period, the methodologies have undergone various transitions, including the increased inclusion of process models and computationally intensive algorithms, as well as a general shift from a purely technical solution (Lauder and McKee, 1986) to partially economic solutions (Abu-Ali and Sabour, 2003; Cisternas et al., 2014). Today, circuit design is largely driven by flowsheet simulation; however, no consistent design methodology is used across the industry.One intriguing approach for circuit evaluation is linear circuit analysis (Meloy, 1983a). This method evaluates the separation potential of the circuit solely considering the unit configuration and stream interconnections. No preliminary data other than the basic circuit configuration is required to use the approach."

Jan 1, 2015

By Steve Kral

In recent years, junior mining companies, mostly listed in Canada, have taken a beating in the finance markets. Simply put, potential investors have been leery of sinking millions into exploration and mining projects due to volatile commodities prices and an uncertain regulatory climate in developed and developing countries. The 2014 edition of the Prospectors and Developers Association of Canada (PDAC), however, seemed to be a bit different for some juniors. Equity valuations have improved and metals prices appear to be stabilizing. So, for some of the stronger junior companies, there is some hope. Merger and acquisition (M&A) activity is picking up and, believe it or not, companies are raising some capital. Billed as the largest annual mining meeting in North America, the PDAC conference attracted more than 25,000 mining and exploration professionals from around the world. Organizers were anticipating attendance to break the 30,000 mark. But, given the state of the exploration end of the mining business, 25,000 is still a respectable number. Junior companies that are in the project feasibility stage, or have made promising discoveries that stand a good chance of proceeding to production, are being looked at by potential investors. Those are the survivors of the last three years of dismal M&A activity. On the other side are the juniors that are still around ? and there are plenty of juniors that were at the PDAC last year but have since disappeared ? but have little or no working capital. One analyst calculated that there are about 850 companies with less than $200,000 in working capital and about 600 with negative working capital. This will likely result in fewer junior mining and exploration companies as the year progresses but the ones that remain should be stronger.

By J. Herman

The Mid-Continent Geophysical Anomaly (M.G.A.) which extends from Michigan into Wisconsin, Minnesota, Iowa, Nebraska, and Kansas, has recently been the object of intense preliminary oil and gas exploration activity involving widespread land leasing, seismic data collection, permitting of deep exploratory holes and other activities (Paul et al., 1985). This report describes the remote-sensing techniques and results of the application of these techniques to study the geology of the M.G.A. and the surroundings in Iowa. In early 1981, Coal Valley Natural Resources contracted Geospectra Corporation to find a large, (100,000 acres or larger) lease block for wildcat oil and gas exploration. The southwest Iowa area was chosen for several reasons. First, southwest Iowa contains the northeast portion of the Forest City basin (Figure 1) which has produced oil and gas from numerous fields in Kansas, Missouri, and Nebraska (Landes, 1970; Petzet, 1982).

Jan 1, 1986

By Joseph B. Alberts, David D. DiPonio, Francis B. Manning

From 1996 to 2001, Wayne County and 13 suburban Detroit communities constructed the Downriver Regional Storage and Transport System (DRSTS) to improve area water quality, protect public health and alleviate basement flooding. The project consisted of a 10-mile long storage and transport tunnel, a pump station at the existing wastewater treatment plant, 9 miles of relief sewers (6 in tunnel and 3 in open cut). The work was separated into 10 contracts. Due to hydraulic design requirements and other constraints, the tunnel profile was located generally 65 feet below ground surface within a soft to medium clay strata which skimmed along the top of a very dense glacial till “hardpan” overlaying bedrock. Boulders within the tunnel bore were recognized as a significant, but indeterminate risk. This paper presents a case history of the owner’s contracting strategy for risk assumption and management of the boulder impacts on the project. Actual conditions encountered during construction and contractual adjustments made to address problems are reviewed, and recommendations for future contracts are included.

Jan 1, 2003

By J. R. Kadambi, C. Shingote, J. Furlan, R. Ke

"Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multi-phase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations, based in some part on the respective current-available theoretical models, and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone was explored with the aid of both computational and experimental techniques (Particle Image Velocimetry). In this study, the flow field with an air core has been investigated; in essence, the research was a two-phase problem, which caused some challenges on both the computational and experimental sides. Two turbulence models were used in the numerical calculations: the Reynolds Stress Model and Large Eddy Simulation. The computational studies are mainly focused on the prediction of the dimensions and shape of the air core. Different section planes of the hydrocyclone were selected as planes of interest and then were divided into several fields of view (FOV) for PIV measurements. Two dimensional experimental velocity vector maps were obtained in each of the fields of view. The computational results were validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles. Keywords: Computational fluid dynamics (CFD); Hydrocyclone; Particle image velocimetry (PIV); Reynolds Stress Model (RSM); Large Eddy Simulation (LES). INTRODUCTION A hydrocyclone is a device used to separate a solid-liquid, liquid-liquid, solid-gas, or liquid-gas suspensions into at least two separate density or particle size components. Hence, the flow field of the hydrocyclone is generally considered a multi-phases flow system. Application of hydrocyclones have been used in numerous industries including oil, drilling, metal working, and mineral processing since 1891, when E. Bretney obtained the first patent for the predecessor design of all contemporary hydrocyclones. A modern hydrocyclone typically consists a cylindrical section at the top where the liquid is being fed tangentially, and a conical chamber attached to the bottom of the cylindrical section, as shown in Figure 1. The characteristics of the feed stream that is injected into the cylindrical chamber play a significant role in hydrocyclone operation. The inlet is tangential relative to the cylindrical chamber and hence causes a centripetal force in the flow field which is considered as the primary separation mechanism."

Jan 1, 2017

By William Gleason

Despite a global slowdown in most mining sectors, Caterpillar, the world?s largest mining equipment maker continues to forge ahead with new, and improved offerings to the global mining industry. On Nov. 10, as part of its Loading and Hauling Mining Focus Session at its Tinaja Hills proving grounds south of Tucson, AZ, Caterpillar unveiled to customers and media its two latest mining products, the 994K wheel loader and 6020B hydraulic shovel. The Caterpillar 994K wheel loader builds on a nearly 25-year history of the 994 model but with one noticeable difference ? the 994K is bigger ? much bigger. Weighing in at 239,142 kg (527,218 lb) the 994 K is up to 20 percent larger and comes with up to 30 percent increase in payload capacity. This behemoth of a machine is currently being tested at Caterpillar?s Tucson Proving Grounds, Anglo Gold Ashanti?s Cripple Creek and Victor gold mine in Colorado and Taseko?s Gibraltor copper and molybdenum mine in British Columbia, Canada.

By Francis X. McCullough

After OSHA published a Notice of Proposed Rulemaking on August 5, 1983, to revise its standards for Underground Construction, many contractors and their representative associations became concerned by the sweeping changes in the proposed rule. After reviewing all of the evidence and testimony on file with OSHA, the contractors presented extensive written and oral testimony to the Department of Labor in Washington, D. C. to help insure that the final published rule would be effective without jeopardizing the economic viability of the industry. The results of those efforts, the entire OSHA rulemaking process, and the opportunity for the construction industry to participate in that process will be discussed.

Jan 1, 1985

By Malte J. M Gurgel

Subsurface spatial planning is becoming increasingly important in view of competing underground applications. This development is influenced by global agreements to reduce greenhouse gas emissions. Therefore, precise knowledge of the underground space is a basic prerequisite for future applications. The three-dimensional registration and reliable georeferencing of underground infrastructures can establish a holistic geodata basis for such tasks. Those tasks are discussed both for the development of energy projects such as deep geothermal energy as well as for storage applications. Research on geothermal energy has been carried out at RWTH Aachen University as part of the SuperC project in a license field in the Aachen area since 2001. Recently, this research has been extended to include monitoring aspects in the overlapping GEObservatorium Aachen field. The documentation and visualization of underground activities using photogrammetric methods like Structure from Motion is discussed based on recent research in sites for the final disposal of radioactive waste. Finally, both applications provide an outlook on supporting underground projects by using high-resolution geodata.

Feb 1, 2025

By Dermot M. Ross-Brown

The more important factors controlling the design of pit slopes are related to the local geology over which the designer has little or no control. Nevertheless, there are some factors over which the designer does exert some control and these concern the say in which the rock is excavated and supported. They include blasting, face cleaning, water control, and the use of rock improvement techniques. The paper discusses these factors and relates the extra costs incurred to the steeper slope angles that can usually be obtained. It is demonstrated that even a modest increase in bench angle of 5° through improved excavation techniques can pay off in a single push-back.

Jan 1, 1975