Search Documents

By C. E. Jordan

The U.S. Bureau of Mines investigated flotation hydrodynamics to improve the recovery of coarse phosphate. Fluid velocity profile measurements were used to characterize the hydrodynamics within commercial phosphate flotation cells and laboratory flotation cells. The effects of agitation, aeration, and pH on coarse phosphate recovery were measured in the laboratory flotation cells and correlated with the hydrodynamics measurements. Test results revealed that the agitation energy and aeration level had a significant effect upon flotation response. By optimizing these two parameters, 92 pct of the phosphate was recovered in a rougher flotation concentrate grading 28 pct P2O5?

Jan 1, 1994

By Makoto Terada

The most important consideration in planning the plugging and sealing of a mine for mine water control is to predict the water flow from the mine. For this purpose, a method of numerical analysis on the water behavior in the ground at the concerned mine area was developed and the mine water flows were simulated. A hydrological survey at the surface of the mine determined the recharge rate of ground- water and the apparent permeability of ground.

Jan 1, 1982

By Franz Wilhelmstoetter, Christian Karner

"The Confederation Line is phase one of Ottawa’s light rail transit, which consists of 13 stops and stations. The project’s center piece is a 2.5 kilometer (1.6 miles) long tunnel with three underground stations leading underneath downtown Ottawa and is constructed within feet of adjacent buildings. The downtown stations, Lyon and Parliament, are caverns approximately 16.5 m (54 ft) by 18 m (59 ft) in a horseshoe configuration constructed in rock, while the third station, Rideau, is approximately 22 m (72 ft) by 18 m (59 ft) in an oval configuration and constructed in mixed ground. The paper will discuss design decisions made early on in the project such as excavation method, unique construction sequencing, and equipment selection, and go on to include corresponding progress rates. The paper also documents design and construction challenges of large caverns in very close proximity to existing buildings and varying ground conditions. Finally, an overview of achieved construction milestones and a current construction progress will be presented. Station cavern excavation is expected to be completed in early 2016. INTRODUCTION The number of urban metro construction projects has certainly increased over the last decades. Cities are growing rapidly all over the planet and many are striving to keep up with the increased demand for public transportation. One of the most feasible types of inner-city transportation with the capacity for large quantities of passengers are metro (subway) systems. Still, large construction projects in dense urban areas often affect the city’s residents in mostly negative ways. During construction, residents face the obstacles of road closures, noise, dust, economic loss for businesses, and property value losses are common. In other words, individuals are directly affected by the way new infrastructures are planned, designed, built and operated. The tunneling industry offers unique opportunities of keeping these side effects to a minimum and possibly avoiding them all together. Although challenged by a variety of constraints (some of which will be discussed in this paper), urban tunneling applications offer a chance to keep cities environmentally, economically, socially, and culturally sound during construction."

Jan 1, 2016

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled- waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SB) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 1, 1984

By K. H. McDaniel

An interactive mine ventilation simulation software program (WIPPVENT) was developed at the Waste Isolation Pilot Plant (WIPP). The WIPP is a U.S. Department of Energy (DOE) research and development project located near Carlsbad, New Mexico. The facility is designed to provide a permanent, safe underground disposal of U.S. defense generated transuranic waste in bedded salt. In addition to its regular functions, the underground ventilation system is engineered to prevent the uncontrolled spread of radioactive materials in the unlikely event of a release. To enhance the operability system, Westinghouse Electric Corporation has developed an interactive mine ventilation simulation software program (WIPPVENT). While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC (copyright © 1991 Mine Ventilation Services, Inc.), the user interface has been completely rewritten as a Windows ® application and screen graphics have been added. WIPPVENT is designed to interact with the WIPP ventilation monitoring systems through the site wide Central Monitoring System.

Jan 1, 1996

By F. X. Meagher

Vertical slot raise driving from bottom up has always been a hazardous, inefficient, high cost operation. The introduction of the Simba 5 drill rig has enabled this type of raise to be drilled accurately from the top down and to be blasted in stages from the bottom up. Safety, high efficiency and low cost were the main criteria in opting for this method. Drop raises with the Simba 5 at Geco have been successfully drilled and blasted up to 115 feet, and this is close to the maximum length of raise that can be drilled and blasted efficiently with Simba 5. A look into the future would indicate a rig capable of drilling up to 200 foot raises with the same accuracy of Simba 5 to 115 feet.

Jan 1, 1974

By Charles B. Escapule

The first successful heap leach of silver ores in the State of Arizona has been under continuous operation since early 1976 at the State of Maine Mine, two miles southwest of Tombstone, Arizona. The silver produced from leaching old mine dumps at this property vas the first in the Tombstone mining district to achieve a 999+ purity. While cyanide leaching of silver and gold ores is a time-proven accepted practice, a relatively new method of treatment called "heap" leaching was employed. Heap leaching is a comparatively inexpensive fast way to recover precious metals from low grade material.

Jan 1, 1981

By B. A. Kennedy

The instrumentation, monitoring, and prediction of a major slope failure at the Chuquicamata mine are described. In December 1967, pre-existing tension cracks on the south end of the east wall of the Chquicamata mine began to open. Various forms of instrumentation were installed for continuous monitoring. These systems included tension crack stakes, crack extensometers, linear extensometers, tape and transit lines, sliding wire contacts, and a seismograph. From the information obtained, the failure date was accurately predicted some five weeks before failure, enabling the mine to reroute truck and rail access; hence, causing a minimal mine shutdown of two and one-half days and preventing any injuries to persons or damage to equipment. The shape and form of the sliding mass are analyzed, as are the possible modes of failure.

Jan 1, 1970

By Nick A. Hasenack

A full survey of the laboratory and blast-furnace tests on 2 types of acid pellets is given. From the laboratory tests, carried out in an atmosphere containing hydrogen, it appears that type B, produced out of 100% magnetitic ores, has a far better low temperature disintegration index and a lower reducibility index than type A, produced from a hematite/magnetite mixture. The swelling index, chemical composition and mechanical properties of both types of pellets do not differ significantly. From the blast-furnace test, carried out with a burden consisting of 45% of pellets and 45% of sinter with basicsty ratio about 2.2, and at constant driving rate, it follows that there is no significant relationship between the disintegration value of the pellets and the blast-furnace permeability. If also is concluded that the lower reducibility of the type B pellets leads to a significantly higher coke consumption.

Jan 1, 1975

By William Kohan

The industrial grinding process has undergone changes to better address the market and economic needs. Fine grinding of dry materials has developed to the point where classifying linings and fine ball charges improve mill efficiencies. Roller mills as well have wide acceptance due to their power efficiencies. The mill, by its nature, cannot provide the specific particle size or range of sizes which are required for further processing or final use. Therefore, various separators are operated in conjunction with the mill to control particle size. The sizing device helps minimize over grinding and control top size. Rising energy costs combined with increasingly tighter quality specifications have led to increasing study of the grinding and separation process.

Jan 1, 1985

By David F. Becker

Two-dimensional, finite-difference elastic modeling aids in planning an optimum seismic-acquisition scheme to define the extent of subsurface cavities resulting from in situ gasification. To understand the seismic effects of a cavity, two models are compared and contrasted. Model A consists of a low-velocity layer (LVL) in a half space; Model B contains a rectangular water-filled cavity in the LVL. Amplitude differences are the dominant effect on the surface records for each model. Cavity resonance and diffraction effects are more definitive in vertical seismic profiles (VSP's) and in a "snapshot" of the wave field. Interpretation and subtraction of corresponding records for both models shows the need for pre- and post-gasification seismic recording. Also VSP data are more informative than surface records.

Jan 1, 1983

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) multiple seam interaction between web and barrier pillars in superjacent mines, ii) subsidence and caving propagating to overlying seams and mines, iii) pooled water and the potential for inundation resulting from a breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, iv) the presence of overlying or underlying mine workings where pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist.

Jan 1, 2009

By R. Berton, M. Walden, S. Melberg, N. Rocco

Recent tailings dam failures around the globe have influenced many mining industry regulators to reassess their requirements for the numerical modelling of tailings dam failures. This type or forward modelling is associated with overarching uncertainties as the model cannot be calibrated against a physical result. Dam breach analyses that meet the requirements of current industry standards and guidance typically begin with identification of credible failure modes and selection of appropriate topographic data set to represent the study area. The breach parameters and the volume of tailings released are then determined using available methodologies and empirical relationships. Subsequently, when the breach hydrograph is developed and the hydrology of stream networks are complete, the runout simulation is implemented. Due to the uncertainty involved in the process, sensitivity analyses are recommended to quantify variations in model inputs on the inundation extent and the flow characteristics. This paper outlines some common methodologies utilized for development of dam breach models, summarizes associated uncertainties with these methodologies and inputs, and provides guidance on how sensitivity analyses can address a wide array of uncertainties inherent in tailings breach analyses. This paper provides an understanding of how selecting appropriate breach parameters can result in reasonably conservative inundation extents consistent with the identified credible failure modes.

Mar 2, 2022

By Rodrigo Peroni, Vitor Campos

Carajás is one of the largest open pit mines in the world. The mine is comprised by a haul road network more than 100 km long, where the need for good roads is paramount and determining of the truck performances. This work integrates, regarding the ultimate pit design, an approach to consider an economic value to an originally unfit material, assuming it has the appropriate characteristics for haul road construction, which sometimes lies over economic iron ore. This measure demonstrated an improvement in the utilization of resources and guarantee the necessary material to the haul road design and Mining Pads maintenance.

Jun 25, 2023

By Nord L. Gale

Lead, zinc, copper, silver, cadmium and many other heavy metals which are potentially hazardous if released into the environment in wastewater discharges have been of considerable concern to governmental agencies, industry and the general public. In response to this concern, an interdisciplinary research team at the University of Missouri has been funded by the National Science Foundation-RANN program to study trace contaminants associated with the production of lead for the past eight years. Seven modern mines in close proximity to two lead smelters in the forested Ozarks of Southeast Missouri are the largest source of lead in the world and in 1976 alone produced 504,095 short tons of lead, 82% of the United States total production. This new and rapid industrial development in a sparsely populated. rural forest region has offered a unique opportunity for studying the impact of trace metals and for developing improved techniques to control detrimental effects. Research on the wastewater discharges and two methods of biological and recycle control are discussed in this paper. Although the two mine-mill complexes investigated in this study have many similarities, the differences between the two are substantive and warrant separate examination.

Jan 1, 1977

By Don Runge, John T. Zeni

Cuprex Limited is currently developing a small gold mining operation in Central Australia in the Tennant Creek field. In February 1984, the company undertook a feasibility study on the project and operations commenced in August 1984. Ore reserves are located between 230 and 280 metres (755 ft and 919 ft) below surface and ore extraction required the establishment of a shaft network for access, ore hoisting and ventilation. Zeni Drilling Company from West Virginia, U.S.A. was contracted to blind drill two shafts for the project. Blind drilling was selected for various reasons, including timing which related to cost efficiency. The blind drill shaft technique has proved successful in this application and with enthusiastic and innovative support from the mining industry, will prove an efficient and cost effective means of accessing and operating underground mining projects of all sizes in the future.

Jan 1, 1987

By E. Maré

Some of the members will probably ask themselves what close relationship exists between hydro-metallurgy and a wet scrubber, but we are sure that as soon as deeper thought is given to the matter it will be realised how vital scrubbing, operations are in metallurgical plants. In ordinary metallurgical installations or pyro-metallurgical processes ore concentrates are first of all shifted from place to place and dust is created. In other cases the ores or concentrates are crushed or dried or roasted, and in each one of these operations dust and fumes, are created. All suspended particles and fumes originating from the abovementioned conditions not only, in many instances, provide health hazards which disrupt production and endanger the personnel in the plant, but also are the source of economic losses through extra maintenance and wear to moving machinery due to abrasion and corrosion. Further losses are incurred by the waste of fine, very often valuable, components. The Party who once said that in several metallurgical plants the bulk of the profits was discharged into the atmosphere by the stack wasn't stretching the truth. There is a place in Africa where a gold producing concern used to lose over 5 oz. of fine gold per day out of a total production of 3000 oz. per month. In another instance, copper concentrate going as high as 80% Cu was discharged into the atmosphere at the rate of 4 tons per day. Realising the value of removing and collecting solids and fumes created in metallurgical plants, a thorough study was made of the available plant and equipment offered on the market. Some units were found very efficient, but very expensive; some others also very efficient but with temperature and maintenance limitations. Some others were also efficient but prohibitive from the point of running costs.

Jan 1, 1963

By Richard C. Neavel

Among the many compositional parameters used to judge the quality of a steam coal is the fouling factor of Attig and Duzy1 [% base in ash % acid in ash X % Na20] in ash. The higher the fouling factor, the more likely the heat transfer surfaces of the boiler will acquire a deleterious deposit of sintered ash. While examining the elemental composition of ash from various size and gravity fractions of coals from Illinois, we noticed that variations in the fouling factor were attributable mostly to variations in the sodium content. Further, sodium content was essentially the same in all sink-float fractions from a given coal. In other words, sodium was related neither to the ash nor to the organic material. We therefore concluded that the sodium was most likely in the pore water, which was approximately a constant proportion of all fractions. This led to the supposition that the sodium might be removable through water extraction. This supposition tended to confirm the observations of Daybell,2 Daybell and Gillham,3 and Gluskoter and Ruch4 that much of the sodium in coals existed as water soluble sodium ions. In passing, it should be noted that most sodium in Western U.S. coals (i.e., Wyoming, North Dakota, Montana) is not water soluble, but rather is fairly strongly held in association with the organic material (ion-exchanged).5 Because data reported in the literature were not very conclusive about the typical proportions of sodium that might be removed by water extraction, and because there were few data indicating extraction rates, and finally, because our calculations showed a favorable economic incentive to lower sodium contents, we initiated an experimental program to investigate water extraction of sodium from Illinois coals.

Jan 1, 1976

By M. Ahmadiantehrani

The concept of hypochlorite treatment prior to cyanidation in the heap leaching of low grade carbonaceous gold ores is discussed. Laboratory column leach tests using a low grade carbonaceous ore were performed to investigate the effects of pH, concentration, hypochlorite consumption, and bed height on the total gold extraction. At high pH, the hypochlorite stability increases and thus, hypochlorite consumption is decreased. At room temperature, the total gold extraction is proportional to the hypochlorite consumption. However, at some point additional hypochlorite consumption does not increase gold extraction. Gold recoveries of 10 and 80 percent are obtained for 12 and 167 lbs/ton hypochlorite consumption, respectively. Increasing hypochlorite concentration increases the rate of extraction. For a given hypochlorite consumption gold extraction was increased by shortening the ore column height. Finally, calcium hypochlorite is more effective than sodium hypochlorite.

Jan 1, 1990

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981