Search Documents

By D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study adsorption of sulfide collectors such as modified thionocarbamates and thioureas, xanthate, dithiophosphate, and dithiophosphinate, on galena, chalcocite, chalcopyrite, and quartz under flotation related conditions. In the case of the adsorption of modified thiourea on chalcopyrite, chalcocite and Cu-activated quartz, and of dithiophosphinate on galena, SIMS measurements have provided direct evidence for the presence of metal-collector (1:1) complexes on surfaces. In the other systems, only the collector molecular ion and its fragments were detected. The distribution of adsorbed species on the surfaces was obtained by using SIMS in the imaging mode. On chalcopyrite, only the copper-collector complex was found; there was no evidence for iron-collector complex. In the case of quartz, adsorption of selective collectors was observed only after activation by copper ions.

Jan 1, 1996

By Collon C. Kennedy, Frances C. Hartogh, C. Joel Casburn

INTRODUCTION During the nineteenth century, the federal mining law was enacted with the objective of promoting the development of the western United States by providing unrestricted access to vast areas of federal land for mineral exploration. Prior to the advent of comprehensive federal, state and local land use plans, there was little, if any, regulation or restriction of mineral exploration activities. Today, the laissez-faire policies of the past that encouraged mineral exploration have gradually given way to the public's legitimate concerns regarding environmental protection, multiple use and planned land development. As a result, the contemporary prospector confronts a maze of statutes, ordinances and regulations with which he must comply to obtain the requisite approvals and permits before commencing mineral exploration on federal, state or private lands. This presentation will provide a broad overview of the exploration permitting process. The first section of this paper recommends certain general management practices to follow when attempting to obtain exploration permits. The second section presents two hypothetical cases, one involving a drilling program on private property in California and the other involving a drilling program and the removal of a bulk sample for metallurgical tests from federal land in Nevada. The cases are used to discuss jurisdictional issues and application of certain federal, state and county laws and regulations that pertain to mineral exploration. The final section contains a brief analysis of three important recent United States Supreme Court decisions. These decisions address the scope of the federal pre-emption doctrine as it applies to activities conducted on unpatented mining claims and the constitutional limits of permissible state and local land use and zoning regulations. PERMITTING PRACTICES The environmental impacts associated with mineral exploration generally result from the construction of drill sites, roads or trenches. Consequently, after the regulatory authority has considered the issues of permissible land use, the primary emphasis of the permitting process is to address problems related to pre-construction site identification and clearance, and post-construction site reclamation. The approaches taken to address these and other related issues vary with the scope of proposed work, the site, the appli-

Jan 1, 1987

By Peter Zhang, Daniel Su, Berk Tulu, Bo Hyun Kim, Zoheir Khademian

Over 2,000 shale gas wells have been drilled in the Pittsburgh Seam longwall reserves. As longwall panels are laid out, some of these shale gas wells must be located in longwall chain pillars. With longwall mining on both sides and the constraint of chain pillar size, gas well in chain pillars are subjected to longwall-induced ground movements and stresses, which could induce deformations in gas well casings Casing deformations are associated with several factors such as overburden geology, surface topography, setback distance, and casing construction. Overburden geology is one important factor that largely determines the locations and levels of deformations in gas well casings Previous NIOSH gas well research has found that casing deformations above the coal seam horizon are smaller under deep cover than unde shallow cover and that casing deformations could occur at the coal seam horizon under deep cover. Recent mine-by cases have provided more insights into the locations and amount of longwall-induced casing deformations as well as the potential occurrence of a large casing deformation at the coal seam horizon. This paper presents three recent mine-by cases with shale gas wells in the chain pillars between two adjacent longwall panels under different overburden depths. Casing deformations were measured by multi-finger caliper surveys and predicted with numerical modeling. With the established numerical model, the effect of overburden depth was further analyzed to investigate the potential occurrence of a large casing deformation at the coal seam horizon under deep cover. These mine-by cases not only provide a general demonstration of how overburden depths can affect longwall-induced stresses and deformations but also give a good indication about the level of casing deformations that could occur under different overburden depths. The study concludes that (1) casing deformations reduce with increase of overburden depths at the gas well; (2) a cementing alternative with production casing uncemented is an effective means to eliminate production casing deformations; and (3) large plastic casing deformation could occur in the production casing at the coat seam horizon under deep cover. The experience and knowledge gained from these mine-by cases would help longwall operators and gaza companies to take appropriate measures to minimize the influence of longwall mining in shale gas wells in chain pillars.

Jun 25, 2024

By Enrique Levy

Central America is graduating this year into large scale mining with the start up of Inco's multi-million dollar nickel laterite processing plant in Guatemala. In the other extreme of the Isthmus in Panama Texas Gulf Sulphur is doing check diamond drilling and foundation test drilling at the Cerro Colorado copper porphyry. The higher price of gold and silver has spurred development and exploration of several small precious metal mines. The purpose of this presentation is to make a brief resumé of the most important mines operating in the area and a list of significant exploration projects. Also, tables will be shown to compare mining codes and taxes. Unfortunately these tables lack information on Panama. Before starting I like to express my appreciation to Kennecott Copper who permitted the use of some of the data compiled by the author on their behalf during the year 1975. Other persons which did not want to be named also have my gratitude.

Jan 1, 1977

By H. Kinilakodi

In 2008, the authors developed a methodology for assessing underground coal mines for high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later using a sample of 103 mines with 2008 and 2009 data, injury measures and MSHA citation data were combined into a Safe Performance Index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performances as compared to large and medium-sized mines.

Jan 1, 2011

By Carl Erickson

The term shortwall mining is somewhat of a mis¬nomer. It may infer a longwall mining system, but of much shorter face length. Actually, continuous pillar mining is a more descriptive term. Coal is mined using a continuous miner as would be done in pillar extrac¬tion, but with the addition of roof supports to control the caving. Face length on such a system typically is 46 to 61 m (150 to 200 ft). The coal is cut in front of the roof supports in the same direction as with a long¬wall shearing machine or plow, but it is mined with a continuous miner and shuttle cars of the same type as used in continuous mining. ROOF SUPPORTS Roof supports for shortwall mining must be con¬siderably larger than those used for longwall mining because of the additional roof to be supported by the wider 2.6- to 3.4-m (81/2- to 11-ft) cut of the continuous miner. Capacities of shortwall chocks in current use vary from about 454 to 726 t (500 to 800 st). The higher capacity as compared to longwall roof supports is needed primarily because of (1) the greater support length, hence more roof weight, and (2) the presence of draw slate in the eastern coal seams, where shortwall is being used. The most popular shortwall support currently used is the four-leg 590 t (650 st) model. This support is shown in Fig. 1. The price of this support is approxi¬mately $25,000 each. As shown in Fig. 1, the shortwall chock incorporates an unusually long forward bar that has an additional hydraulically operated extension bar to provide face support for the wide miner cut. METHOD OF OPERATION Mining Sequence In shortwall mining, two or three (depending upon the chock design) move up cycles of the chock are needed because of the miner cut width. Fig. 2 depicts the five steps required to complete the move of chock and spill plate using a miner that takes a 3.3-m (10-ft,

Jan 1, 1982

By D. Boreck

The Bureau of Mines is conducting research on the feasibility of incorporating in situ stope leaching into active underground metal mines. Stope leaching, a modified in situ leaching technique, proposes to recover metals by leaching fragmented ore in existing underground openings and collecting and processing the metal-bearing solution to recover the valuable metals. If leaching solutions escape from the stope, either through geologic discontinuities or highly permeable zones in the rock, valuable metals dissolved in the solution may be lost. Escaping solutions may also contaminate ground waters. Consequently, in fractured rock, the characteristics of the fractures in the vicinity of the leaching stope must be understood before introducing actual leach solutions into the stope. Effectively characterizing a rock mass requires the integration of several disciplines including structural geology, borehole geophysics, hydrology, geochemistry, and mining engineering. This paper will focus on the general geologic and geophysical techniques that can be used to characterize the rock mass at an underground simulated stope leaching site. The results of several geophysical logging methods, tested at the site, are compared to the geologic core descriptions. Then, the? effectiveness of the different geophysical techniques in delineating fracture zones will be assessed. Knowledge gained through the geologic and geophysical analyses can be used to supplement results from hydrologic testing. This information can also be utilized in designing blast patterns and developing strategies for controlling or blocking movement of escaping leach solutions.

Jan 1, 1991

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90-wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct resulting in attempts for magnetic separation. These separations are desirable in the notion that there is no waste product generated from this type of processing and consequently an opportunity for complete utilization of the waste material. Conversely, the pre-separated material could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Critical assessment of the recovery sequence chosen for the products has been described based on economics.

Jan 1, 2001

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

The level of automation employed in flotation production is relatively low. In an actual concentrator, operators use their judgment to adjust the production state based on the visual characteristics of the flotation froth surface. There are shortcomings, such as strong subjectivity and lagging process operation, that easily cause the waste of manpower and material resources. Machine vision technology is introduced to replace human visualization, achieving a quantitative description of the visual characteristics of the froth surface. The state variable parameters are provided for the identification of the flotation conditions.

By Kenneth J. Edmiston

The objectives of this paper are: to review the current status of chloride leach processes for sulfide concentrates, to make an evaluation as to the applicability of chloride leaching for replacing pyrometallurgical processes and to comment on recent advances in construction materials. The paper does not delve in detail on process chemistry. Sufficient references are presented on each process to allow the interested researcher to obtain process chemistry details. GENERAL The fact that chloride oxidates can solubilize base metals from sulfide concentrates has been known since the 1880's. The work of Hoepfner in 1902 was particularly accurate for its time with regard to the chemistry of chloride solutions. Recent work has dealt with the understanding of chloride extraction thermodynamics by modelling the behavior of metal chloride complexes. In the last several years several excellent review articles and symposiums have been issued covering chloride chemistry (1 thru 6).

Jan 1, 1984

By DEVY DYSON, Brian Hart, JOHN LANGHANS, Stamen Dimov, STEVE YOPPS

A recent Nevada Gold Mines research program focused on the pressure oxidation (POx) pretreatment of a Carlin-type double refractory ore from the Turquoise Ridge Mine. The research team found that both arsenian pyrite and carbonaceous matter were highly oxidized within an hour at 300 °C using a bench-top autoclave reactor and that the gold recovery from the residues after cyanide/carbon-in-leach (CIL) approached the technical limit set by the amount of gold encapsulated by silicate minerals. Although the 60-min pretreatment at 300 °C yields robust performance when treating a whole ore, copper additives can catalyze the oxidation rate of carbonaceous matter and reduce the residence time needed at elevated temperatures. Certain gangue minerals are susceptible to dissolution in acidic solutions at 300 °C, and this may cause poor gold recovery. This recovery challenge is mitigated by keeping free acid in the discharge solution below a key threshold.

Nov 1, 2022

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24v0 of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50v0 of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include: • extraction of thick seam in ascending order with stowing; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. • Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof; four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 1, 1988

By M. J. Shulman

The exploration geologist is frequently confronted with the problem of allocating his resources, i.e., exploration effort, among various areas. Although geologic, financial and logistic considerations influence the allocations, no objective criterion is usually given which determines the optimal allocation. Maximizing the gain in information, subject to the constraint of a limited exploration budget, is used as the objective criterion to allocate reconnaissance effort. The information function, I(x), quantifies the expected gain in information, where x is the scale of exploration. To calculate the information function the following data are necessary: 1. The probability that an area contains a target must be estimated. 2. For each scale of exploration, four probabilities must be estimated: the probability that an anomaly is produced by the target; the probability that an anomaly is not produced by the target; the probability that an anomaly is produced by a barren area (false signal); and the probability that an anomaly is not produced by a barren area. Alternatively, the barren area can be replaced by other targets. To illustrate the allocation model, the optimal number of line kilometers/line spacing per area is determined for an aeromagnetic survey for iron in Egypt.

Jan 1, 1985

By T. P. Lim, A. J. Vivyurka, N. K. Davé

Chemical and radioisotope stratification studies were carried out in an abandoned uranium tailings pile at Elliot Lake, Ontario, Canada. The tailings, with an average thickness of 7 m over an area of 16 hectares, were deposited approximately 20 years ago on a layer of black peaty material which overlays deposits of permeable glaciofluvial sands. Geohydro-chemical investigations of this tailings area have been ongoing since 1978. The radioisotope profile study was conducted on three adjacent sites. Solid core samples, collected with a split spoon sampler at various depths, were analyzed for various chemical and radioisotope constituents. The results indicated by 2 distinct zones of stratification; an upper zone, where the constituents were uniformly distributed, and a lower zone, near the peat-tailing interface, which showed increasing concentration with depth. Within the peat layer, the concentration decreased rapidly with no significant levels of contaminant penetration below the peat layers observed, though the samples were limited. The pH profile showed that the top 5 m of the tailings have been oxidized, the average soil pH in this zone was 3.4 compared to 5 .8 underneath it. The groundwater hydrology of the system was observed to be complex showing downward and lateral flow in the dry season and lateral and upward flow during the spring and periods of heavy rainfall. The results are discussed in terms of a model based on the combined segregation and settling process of the tailings fine fraction, and the geohydro-chemical interaction of the solid and liquid phases.

Jan 1, 1981

By Dan Nilsson

The Luossavaara "Research Mine" is the First large, offensive effort in mining research conducted by the Swedish state. Over a 5-year period, 1981-1985, the Swedish Mining Research Foundation works in the "Research Mine" on the development of mining systems and equipment. The purpose is to bolster the competitive strength of the Swedish mining and mining equipment industry. The previosly abandoned Luossavaara mine in Kiruna, in northern Sweden, has been reopened especially For the project. Ore is mined and sold during the course of the research project. The income from the sales covers a large portion of the costs for teh research.

Jan 1, 1985

By R. P. Stahura

Conveyors are the lifeline of mining and processing operations. They continuously supply materials to and carry finished products and waste away from operations. When conveyors are running at less than maximum efficiency, the operation's productivity is in trouble. Inefficient conveyors suffer carryback, leading to the buildup of materials on idlers and other expensive components. They spill and leak material at loading zones and conveyor transfer points. This causes accumulations that can damage the belt, wear moving components and increase both clean-up labor and maintenance expenses. They wander or mistrack, spilling material and endangering personnel and conveyor components. And through these inefficiencies, they multiply the operation's hidden costs. These added expenses occur in lost production, increased downtime for service and maintenance and replacement costs for prematurely worn equip¬ment. In addition, the attitude that inefficiency is "good enough" is recognized elsewhere in the organization. As a result, other departments relax or operate at less than peak performance. Quality goes down along with employee morale. Costs of inefficient conveyors A key to efficiency is handling a product as few times as is necessary. That means conveyors should be loaded, track true to the unloading point and then be unloaded, all without material escape or waste motion. An inefficient conveyor is often signaled by accumulations of DURT - material that has escaped from the system and is now at large in the plant. This DURT adds costs to an operation that are uncounted and, perhaps, uncountable.

Jan 1, 1992

By B. N. Thompson

The main industrial minerals produced are non-metallic - clay, dolomite, limestone, pumice, salt, serpentine, and silica sand. The other minerals, some with minor production, include diatomite, feldspar, magnesite, sulphur, asbestos, and perlite. Energy and metallic minerals and aggregate are excluded from this account. These industrial minerals occur in a wide range of rock types and geological ages. For example clays are known from the weathering products of Cretaceous rhyolite and leaching of Eocene coal measures; from Quaternary weathering of contemporary loess and shallow marine sediments, and of greywacke of Triassic-Jurassic age; and from the hydrothermal alteration of Late Cenozoic acidic volcanic rocks.

Jan 1, 1982

By Andrea B. Baldwin

In recent years, federal and state regulatory agencies have tightened air emission standards. Two of the acid gases, hydrochloric acid (HCI) and sulfur dioxide (SO2), are under heavy scrutiny for reduction. . Most traditional scrubbing systems, i.e. wet scrubbers and spray dryers, meet the standards but they typically are high in capital cost, have significant space requirements for equipment, and are difficult to maintain. Dry sodium injection (DSI) is a alternative technology that has been shown to be effective in HCl and SO2 removal while being the inverse to the problems listed with traditional systems. This paper covers the mechanics of dry injection scrubbing using the most effective sorbents, sodium bicarbonate and mechanically-refined trona (natural sodium sesquicarbonate). It presents DSI performance data for Chambers Medical located in Hampton, SC. This facility incinerates local medical and municipal solid waste. Chambers Medical has used mechanically-fined trona for HCl and SO2 removal since late 1991.

Jan 1, 1995

By G. S. Dobby

High-intensity wet magnetic separators have been successfully introduced into the mineral processing field over the past ten to fifteen years, due largely to rapid advancements in magnet design. Wet magnetic separation, until recent years, was applied solely to the concentration of minerals of high magnetic susceptibility, such as magnetite, at relatively coarse sizes. Now, however, high-intensity separators are capable of treating weakly paramagnetic minerals and have extended the range of treatable particle size down to about one micrometre(1,2). . One of the more recent-high-intensity separators developed is the Kolm¬Marston Marston type high-gradient magnetic separator (HGMS) (3,4) It consists basically of an iron-clad solenoid surrounding a matrix material - a fine, ferromagnetic steel wool or expanded metal lath. A schematic diagram of the device is shown in Figure 1. Large, highly localized, pertebations of the magnetic field are created by the ferromagnetic matrix. It is these field gradients that are instrumental in developing large magnetic forces which act on the mineral particles. Operation of the separator is simple. Slurried sample is fed through the matrix and, depending upon the mineral parameters of particle size and magnetic susceptibility and. the operating parameters of flow rate, field strength and feed weight, some particles will be attracted to and adhere to the magnetized matrix, while the others will flow through the matrix. The separation is completed by later removing the background magnetic field and flushing the captured mineral particles into a separate container. The process can also be applied on a continuous basis (S).

Jan 1, 1977

By Glenn E. Craig

The practical and effective pulp distributor here presented is believed to be of a completely new and innovative design. It was developed at the San Nicolas Plant of the Marcona Mining Company in Peru, where it has been thoroughly plant tested using iron ore slurries of a particularly abrasive nature. It has proven to be superior to the apparatus originally installed, or to any observed in operation elsewhere. In plant practice the capacity and efficiency of many process units such as screens, magnetic separators, and jigs are strongly affected by the loading pattern, and for better results the flow of pulp must be proportioned across the receiving lip in equal quantities per unit width. The distributors originally installed on the drum magnetic separators in San Nicolas proved to be unsatisfactory, and several trial modifications failed to show any improvement. As is usually the case, feed rates were being steadily increased, and appreciable losses to tailings resulted. A check of the distributors on the market discloses no reasonable substitute, so efforts were directed toward devising an entirely new type. Required was a positive type of action which would guarantee that the pulp flow be spread equally along the length of the drum. Discussion As indicated, the motivation for development was simple necessity. The plant in San Nicolas crushes, grinds, and concentrates magnetic iron ores of a particularly abrasive nature, and depends largely on magnetic separation to obtain a marketable product. Feed to the numerous drum magnetic cobbers and finishers varies from rod mill discharge at a nominal minus ten mesh to a ball mill fine grind of seventy percent minus three hundred and twenty-five mesh. Operational factors affecting the magnetic separators were well controlled,

Jan 1, 1971