Search Documents

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching' into a science. Leaching of copper, whether from copper-bearing ore or waste, follows well established chemical reactions. These reactions are commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300, 000 tons of copper are produced annually in this manner where as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced.. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydro-metallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks, or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 1, 1972

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module (Fig. 1). The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information. Key for Fig. 1 A-Helium-3 neutron detector B-Wax moderator for neutrons C-Irradiation chamber D-Funnel for receiving ore E-Gate F-Transducers G-Biological shield for neutron source H-Transfer tube for neutron source I-Neutron source J- Microprocessor K-Accumulator for hydraulics L-Control panel M-Electro-hydraulic servo valve to control movement of the source N-Electro-hydraulic proportional valve to control movement of the gate O-Hydraulic power unit Irradiation and Counting Equipment Irradiation of the ore is achieved using a 1 X 10 7 neutron*s-1 californium-252 neutron source. The source is contained in an iron capsule and pneumatically transferred between the irradiation/counting and storage chambers. The irradiation/counting chamber possesses 12, 600-mm (24-in.) long helium-3 thermal neutron detectors embedded in an annulus of wax (Fig. 1). Two sets of six detectors are each interfaced to a preamplifier, amplifier and single-channel pulseheight analyzer system, and the two systems are connected to a scaler. A special timing unit controls the transfer of the source and the on and off switching of the detector assembly, in sequence with the movement of the source. Results and Discussion In the experimental demonstration, using the 107 neutron.s-1 source, a 10% uranium ore was measured to ± 10% (2o total error) in 10 cycles and ±6% (2o) in 100 cycles. Since a larger source was not available, it can be statistically predicted that a 109 neutron-s-1 source could be used to measure a 0.1% ore to ± 10% (20) in 10 cycles. The uranium can occur as discrete nonhomogeneous particles in the ore, and the error caused by such a distribution of particles is ± 4% (2o), as determined by

Jan 1, 1984

By Ö. Kaya

The removal of gangue minerals from three different graphite ores (Inebolu, Akdag?madeni and Çoraklidere) from Turkey by acid leaching was studied. Acid leaching experiments were applied to the flotation bulk concentrates, which were obtained in determined optimum conditions after preliminary flotation tests. The effects of acid type, acid concentration, leaching temperature and leaching time on the dissolution of gangue minerals were studied. The most suitable leaching conditions were determined to be 20% HCl + 4% HF for acid type and concentration, 85 ºC for leaching temperature and 4 hours for leaching time. After removing the gangue minerals at these optimum conditions, the total carbon contents of the samples from Inebolu, Akdag?madeni and Çoraklidere increased from 23.51% to 40.07%, from 37.93 to 60.47% and from 42.28 to 59.47%, respectively.

Jan 1, 2009

By D. W. Fuerstenau

One of the more energy-efficient methods for size reduction, namely particle-bed comminution under high compressive loads, was employed to grind eight minerals and ores, using up to 250 MPa pressure. A new approach based on the self-preserving character of the ground product size distributions and a linear energy-reduction ratio relationship is proposed for analyzing this mode of size reduction. The grind ability of the material when comminuted in a particle bed is about one-half that of the single-particle crushing mode, which is in agreement with previous estimates of the relative efficiencies of energy utilization based on direct measurements of surface area produced. The loss of efficiency may be attributed to energy dissipation by particle interaction phenomena in compressed beds.

Jan 1, 1993

By T. C. Bibb

Longwalls using shearers in seam heights of less than 1.2 m (48 inches) are relatively rare in the U.S. Westmoreland Coal Company is currently operating a shearer-equipped longwall at a cutting height of 1.17 m (46 inches) in its Bullitt Mine. This face has averaged 2795 metric tons/day of operation since its startup on April 3, 1984. Longwall productivity in thin seams is substantially impacted by equipment reliability and availability of useable working room for travel and access. This paper addresses the design criteria used in selecting this face equipment, with the goal of maximizing these two parameters. Equipment discussed includes shearers. face conveyor, shields, stageloader, and emulsion system.

Jan 1, 1985

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By Roger Escoda Estelrich, Joan Carles Casado Ortega, Mitchell Gerdau, Jose Raul Martinez, Jeb Pittsinger, Frank Perrone

The existing Chesapeake Bay Bridge-Tunnel complex is being expanded to include the Parallel Thimble Shoal Tunnel. This will be a subaqueous bored crossing between two islands constructed for the original 1960s immersed-tube tunnel. Jet grouting was employed by the Chesapeake Tunnel Joint Venture (CTJV) to provide watertight base plugs, launch and retrieval blocks for the tunnel boring machine (TBM), a TBM canopy to limit ground movement, and a retaining wall to enable off-island excavation: all within hydraulically placed sands. This paper will review the design and construction challenges, including soil permeability and recharge, grout communication, installed grout strengths, and remediation requirements.

Jun 23, 2024

By Y. Paul Chugh

NIOSH and the Illinois Clean Coal Institute are funding studies on characterization of coal and quartz dust in Interior Basin mines since 2009. Coal dust characteristics vary significantly and, are vital for the development of the engineering controls. This paper presents wettability characteristics of coal dust with respect to its chemical and physical properties, since wettability is considered to be a primary dust control technique. Particle size distribution, inter-particle interactions during wetting and quartz associations with organic and inorganic matter in coal seams is critical for understanding wetting phenomena. Silica content in the un-wetted fractions was found to be very high during wetting tests. Wetting of quartz may be limited by its association to hydrophobic materials as well as buoyancy forces resulting from particle size characteristics and particle-particle interaction in the wetting agent. Temperature of the wetting solution and effective contact time between dust particles and water droplets are found to be two important variables affecting the wettability. The characterization data obtained from this study can be utilized to develop engineering controls.

Jan 1, 2011

By Russell Frith

A review of published literature reveals case histories whereby the entire periphery of a coal pillar has “burst” out as a single event during first workings, the associated energy and material release causing significant damage to adjacent roadways and any equipment/infrastructure located within said roadways. Such events are distinct from coal burst events during first workings such as that at the Austar Mine in 2014, or those linked to overburden bumps related to either horizontal stress-driven slip along major faults and/or thick, massive strata units in the overburden or floor of the coal seam.

By L. G. Tejada, T. Sjursen

In the production of ferronickel at Falconbridge Dominicana's plant in the Dominican Republic the Reduction Plant plays a vital role by partially reducing the nickeliferous oxide ore, and pre- heating the charge to the electric furnaces. Ore is agglomerated in the form of pillow-shaped briquettes which are screened and fed to 12 open-top shaft furnaces. Hot (over 1250°C) reducing gases are partially cooled (less than 1150°C) and introduced through a set of primary tuyeres. The reducing gas rises counter-currently to the flow of solids. A portion of the partially spent reducing gas is withdrawn at the furnace top and recirculated through a set of secondary tuyeres, 1800 nrm above the primary tuyeres. Together with the recycle gas a controlled amount of air is also added to react with the partially spent reducing gas in order to preheat and dry the charge in the upper part of the shaft furnaces. The calcine is discharged through three discharge legs and pusher block assemblies into open-top refractory lined cars. These cars are then hauled to the electric furnace, parked over selected feed ports, and discharged through bottom gates. The furnace exhaust gas is de-dusted in cyclones and then passed through Venturi scrubbers. The slurry is fed to a thickener, filtered, and recycled to the ore receiving hopper in the ore preparation area. Dust generated throughout the plant is collected, wetted to conform with briquette press feed, and recirculated in a controlled manner through the feed system.

Jan 1, 1979

By Paul B. Valenti

The Nevada Moly Operation of Anaconda Minerals Co., (a molybdenum/copper ore body) was initiated in 1978, with a contract to Bechtel Civil and Minerals Inc. for construction of a mining and milling facility near Tonopah, NV. Ground was broken on the concentrator portion of the project in August 1979$ with a multi-phased startup of the mill beginning in June 1981. Processing design tonnage of 20 000 t/d (22,000 STPD) was reached in early 1982. Major pitfalls of rapid design and implementation of engineering, construction, and startup are considered. The operation of the concentrator including SAG milling, ball milling, bulk rougher flotation, copper/moly separation, moly regrinding and cleaning, thickening, and product loadout are discussed.

Jan 1, 1983

By Leandro Augusto Viana Teixeira, Angela Avelar, Ruberlan Gomes Silva, Virginia S. T. Ciminelli, Daniel Majuste

Rare earth elements are essential for modern life products and green technologies. Recent supply constraints have boosted the development of rare earth projects after the price peak of 2011. The feasibility of a project depends on the definition of a processing route, which in turn depends primarily on the rare earth mineral, with monazite and bastnaesite representing the two most relevant minerals. Monazite-type ores usually contain high acid consumption impurities, such as iron, aluminum, calcium, magnesium and phosphates, and may also contain prohibitive levels of radioactive thorium in its composition. Based on thermodynamic analysis, the present work discusses the fundamentals of a selective process route for rare earth extraction from monazite ores with high iron content. This process involves sulfation by means of concentrated sulfuric acid and roasting at a high temperature. The route yields high rare earth extraction with low iron and thorium extraction and low acid consumption. Rare earth extractions as high as 80 percent were achieved, while iron and thorium extractions were lower than 1 percent, and acid consumption was lower than 0.34 kg of sulfuric acid per kg of ore. The operational window was compared to the one predicted by thermodynamic modeling, with 700 °C representing the optimal roasting temperature.

By V. Gall, J. Rudolf

The Virginia Department of Rail and Public Transportation and the Metropolitan Washington Airports Authority are undertaking the extension of Washington Metropolitan Area Transit Authority’s Metrorail service to Washington Dulles International Airport and beyond to Route 772 in Loudoun County, Virginia. The roughly 37 kilometers long, double track alignment involves two 700 meters long single track, soft ground NATM tunnels at Tysons Corner, two 3.3 kilometers long single track rock TBM tunnels at Dulles Airport and one 25-meter deep station at the airport to be constructed by NATM in sedimentary rock. The design-build project is being implemented in a Public-Private-Partnership. A joint venture of Bechtel and Washington Group International has concluded the preliminary engineering and construction is scheduled to start in late 2007.

Jan 1, 2007

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By Antonio Tafra, Rene Dominguez, James Spenceley, Brady Hays

"Extracting one of the world’s most valuable natural resources — copper — hinges on the availability of the world’s most essential resource: fresh water. But try sourcing fresh water in one of the driest places on Earth, Chile’s Atacama Desert.BHP, majority owner of the Escondida copper mine in Chile’s Antofagasta region and Minera Escondida Limitada (MEL), operator of the mine, were looking for sustainable solutions to deliver desalinated water to the mine, while protecting the environment and complying with the local water authorityregulations.The mining giant chose Black & Veatch to solve this challenge.Solving a global miningchallengeMines use large quantities of water for mineral processing and metal recovery. Water supply, and not mineral ore, is often the major constraint to mining production and development of projects, especially in Chile. Mining operations must have a reliable water source that complies with local regulations, without adversely impacting the environment or affecting the water supply of nearby communities.Worldwide, mining companies and their owners, shareholders and regulators are placing new levels of focus on minimizing the impact of mines on the surrounding landscape and communities. Balancing the economic benefits and needs of mining operations with the potential freshwater impacts requires mines to pay serious heed to the environmental and social issues related to water. Today, mining companies are being proactive and are taking action to protect precious freshwater resources while seeking opportunities to reduce and mitigate their water impact.Delivering a desalination solutionBHP and MEL needed an efficient, technologically advanced seawater desalination plant, along with a conveyance system and infrastructure that would carry desalinated water more than 180 km (112 miles) from the ocean to the mine. Four pumping stations convey the water to a reservoir at the mine site, which is 3,200 m (10,500 ft) above sea level."

Jan 6, 2018

By Robert L. Zook

Coal refuse slurry impoundments are dams constructed of coarse coal refuse to impound fine refuse (slurry) and water (25-30% solids). Both products are waste from coal preparation plants. A number of these structures in West Virginia, Pennsylvania and Kentucky were investigated to determine embankment stability. During the investigation a variety of embankment designs were encountered. The investigation determined the soil and geological characteristics of the embankments and the sites. This was accomplished by a test drilling and monitor installation (observation wells and piezometers) program, geologic study, and large scale mapping which allowed sub-surface profiles of the embankments to be constructed. The laboratory testing program concentrated on textural classification of the coal refuse, permeability and determining strength parameters to be utilized in the stability analyses. For the stability analyses, the Modified Fellinius Slip Circle, Simplified Bishop Slip Circle and Analysis for Translational Failure -were utilized. In all stability analyses hydrostatic pressure and earthquake were considered. This investigation indicated that 62% of the embankments analyzed are in a stable condition. The coal seam mined, the type of roof rock, and the gradation of the refuse influence the degree of compaction obtainable and the permeability of refuse. The shear strength of coal refuse appears to be controlled by its composition, moisture content, degree of compaction, amount and grain size of fines present. This investigation demonstrated these em¬bankments should not be treated as pure state-of-the-art dams; consideration must be given to the particular properties of coal refuse and the total refuse disposal system. Refuse dim slurry impoundments generally lack the site se- lection phase that is standard practice with siting most other types of dams.

Jan 1, 1974

By C. H. Bucknam

Principles of Green Chemistry provide useful guidance for sustainable mineral process development. Laboratory bench scale testing was carried out using pregnant cyanide leach solutions, and a number of commercially available mercury precipitation reagents were compared using jar testing to determine the most efficient and selective reagents for mercury precipitation. The most efficient reagent identified was sodium polymeric thiocarbonate (NaPTC).Coagulation experiments with fine diatomaceous earth resulted in a stable precipitate, with good settling properties. On line monitoring of the mercury in solution is recommended for process implementation to conserve reagent removing approximately 90-95% of the mercury with minimal silver and negligible gold losses.

Jan 1, 2004

By Dávila-Pulido. G., L. Magallanes-Hernández, F. López-Saucedo, J. Batista Rodríguez, A. Uribe-Salas

"This paper presents the results of tests performed to study the effect of slurry solids concentration on the behavior of gas dispersion in industrial-scale mechanical flotation cells. The experiments were conducted at five concentrator facilities run by a Mexican mining company, specifically in the rougher bank of the lead/zinc flotation circuits. Those mechanical cells having significant contribution to the performance of the circuit, that is, the cells that enable high recovery, were characterized. The measurement protocol enables measurement of the superficial gas velocity, gas holdup and bubble size, and sampling of the mineral slurry. The measured data indicate that bubble size and gas holdup decreases as the concentration of solids increases. IntroductionThe process of mineral concentration by flotation is based on contact between particles and air bubbles, the selective adhesion of hydrophobic particles onto the bubbles, and the rising of the bubble-particle aggregates to the surface of the flotation cell to overflow over the lip to form the concentrate. It is now accepted that the physical and chemical process variables that control the flotation of hydrophobic particles are closely related to gas dispersion (Schwarz and Alexander, 2005). Gas dispersion is defined by the superficial gas velocity, Jg (Torrealba-Vargas, Gomez and Finch, 2006), the gas holdup, eg (Tavera, Gomez and Finch, 1997), the bubble size, d32 (Dobby and Finch, 1986; Gorain et al., 1995; Hernandez-Aguilar et al., 2004) , and the bubble surface area flux, Sb (Manqiu and Finch, 1989; Manqiu, Finch and Uribe-Salas, 1991). In recent years, the advances that have been made in sensor technology have enabled the characterization of gas dispersion in industrial flotation cells with excellent results (Gomez and Finch, 2007). This technology advancement has allowed the gaining of a deeper understanding of such complex mechanisms as carrying capacity (Yianatos and Contreras, 2010), collection efficiency (Gorain, Franzidis and Manlapig, 1997; Massinaei et al., 2009) and bubble coalescence (Finch, Nesset and Acuña, 2008; Zangooi, Gomez and Finch, 2010)."

Jan 1, 2017

By R. Mensah-Biney

The adsorption of gold-thiourea complex onto a cation exchange resin, Amberlite 252, has been evaluated in a batch stirred reactor. The observed non equilibrium saturation capacity was 3.20 meg Au/g dry resin (620 kg/t) whereas the equilibrium ion exchange capacity was only 0.53 meq/g (103 kg/t). The enthalpy of adsorption was 4 -25 kJ/mole under equilibrium conditions and increased to 20-200 kJ/mole under non equilibrium conditions. Under non equilibrium conditions, the adsorption capacity of the resin decreased with increasing temperature and increasing thiourea concentration and increased with increasing gold concentration. This dependence of adsorption capacity on thiourea concentration and temperature may be a useful tool for elution of gold from the loaded resin. Scanning electron microscopy revealed evidence of deposition of elemental gold on the loaded resin under non equilibrium conditions. The proposed mechanism for "adsorption" of gold-thiourea complex onto this cation exchange resin consists of an ion exchange reaction followed by a reduction of the exchanged gold complex to elemental gold on the surface of the resin.

Jan 1, 1997

By David C. Girard, Larry Williamson, Leonard R. Benson, Ronald E. Bizzarri

On the east side of Washington DC, the DC Water & Sewer Authority is developing a Facility Plan for the Anacostia River CSO Control Projects, including 8 to 12 miles of CSO storage/conveyance and flood relief tunnels and associated facilities. The project includes major technical and non-technical challenges, including: completion under a Federal Consent Decree schedule; large diameter (estimated 25 to 35 ft) soft ground tunnels and shafts up to 200 ft depth; operations without use of active flow control systems; and close coordination with several major public and private construction and development projects that are being advanced in the project area.

Jan 1, 2007