Search Documents

By G. Bylapudi, A. Spearing, J. Weber, K. Mondal

U.S. National Institute for Occupational Safety and Health (NIOSH) reports state that about 100 million rock anchors are installed annually in U.S. coal mines (Tadolini et al., 2006), and rock-related safety remains an issue. The majority of these coal mines have conditions that make corrosion probable in the longer term. Despite this, very little research has been performed to analyze corrosion and its effects on rock anchors in coal mines. To further evaluate the effects of corrosive conditions in coal mines on rock anchors, three different experiments were conducted during an initial Illinois Clean Coal Institute (ICCI)-funded project from 2008-2009. The results of these experiments were further studied, with additional tests, in the extended ICCI-funded project during 2011-2012. The experiments were destructive testing, electrochemical testing (potentiodynamic polarization tests) and open circuit potential (OCP) testing, conducted in order to study corrosion in environments similar to those found in Illinois coal mines with a focus on major rock anchor types typically installed underground. Destructive test results showed highest reduction in peak strength at higher pH and temperature. From the destructive test results, epoxy-coated and galvanized anchors were observed to be better when compared to uncoated. Electrochemical testing was performed to find the corrosion potential and corrosion rates of ASTM A615 steel grades 40, 60 and 75 in four different solutions of varying sulfur content at ambient temperature. The effect of temperature and pH levels on corrosion potential and corrosion rates of steel grades were also evaluated with additional electrochemical testing, where an increase in temperature with all other constant conditions caused a significant increase in the corrosion penetration rate. OCP data indicated higher corrosion potential values (-mV) for rock anchors in wet areas, when compared to those from the dry areas. OCP test results of the rock anchors from the laboratory corrosion chambers were similar to those measured in the sampled coal mines.

Jan 1, 2013

By John Sasadi

Several years ago I wrote a comprehensive paper 'entitled, "Future Trend of Bulk Carriers" dealing with the principle dimensions of vessels and how they can be predicted; then with loading and unloading of large carriers, especially considering various designs of "Self Unloaders". Since writing the paper, many large bulk carriers were basically built along the, predictions made. Maximum size today is in the 150,000 DWT class, with few exceptions, which are combination carriers (ore-oil) or OBO's (oil-bulk-ore) in the 200-250,000 DWT class in the same paper, many references were made cautioning engineers not to design ports which could be "obsolete tomorrow", however, these were not always followed. Nevertheless, during the past few years many modern ports were built signaling the beginning of a new area of "Super Ports". Super Ports can be built for various reasons, most important to provide transfer stations where bulk material is received from large carriers then transferred to smaller vessels or barges for distribution. Obviously, opposite movement of bulk commodities can justify the building of "Super Ports", however, these are not as difficult to build for many reasons. The Material Handling Industry has developed efficient means of unloading smaller vessels or barges with continuous-type unloaders and has mastered the art of storing, reclaiming, and moving large quantities of bulk material to high-capacity shiploaders. Nevertheless, the industry has failed to design and market efficient ship unloaders which in any way could match the presently attainable shiploading rates. For these reasons, it is considerably more difficult to build "Super Ports" for incoming rather than outgoing bulk materials with large bulk carriers. The purpose of this paper is to elaborate on problems affecting high-capacity, continuous ship unloaders, especially involving large bulk carriers. For better understanding, some references will be made to the smaller, continuous barge or ship unloaders, but only as the principles affect the larger units. Additional references will also be made to exploit the present "State-of-Art" of the grab

Jan 1, 1972

By John S. Wakeman

The initial step in the pelletizing of iron ores is the production of green balls. The importance of this step cannot be overemphasized as the physical quality of the green balls has a very significant effect on the subsequent induration process, regardless of the type of the indurating equipment employed. The ability of the green balls to withstand the rigors of handling, distribution, compaction and drying will have an effect on the degree of success of any pelletizing operation. Many factors affect the physical quality of the green balls including the prior processing of the iron ore, the characteristics of the balling feed and the type and quality of the binder used (if any). When working on the development of a new project or studying an existing operation, it is often desirable to determine what effect variations in these factors will have on green ball quality. It is generally impractical to make these determinations on a commercial, or even pilot plant scale, especially when the number of variables to be studied is large. Because of this, many organizations have developed batch techniques for producing green balls to enable them to perform such investigations with a minimum of time and expense. The batch balling method is at best, only an approximation of commercial balling systems. Many practitioners employ the use of pre-formed seed pellets to initiate a batch run. Thus, the growth mechanism encountered in any experiment is essentially snowballing. Unless an instability is introduced into a balling test (such as an excessive initial feed rate or an unusual feed material characteristic) the growth mechanism of coalescence is not present to a significant extent nor is it desirable. In a continuous operation, both mechanisms are present and necessary to sustaining the system. The batch balling technique thus produces pellets in an idealized manner and cannot be used to directly predict commercial green ball qualities. A general relationship does exist however, and the procedure is fairly sensitive to variations in test parameters. Although many refinements to this technique have been introduced over the years, batch balling is still essentially an art and subject to "operator effect". Therefore, to assure consistant and reliable results, skilled technicians who carefully adhere to established practice must be utilized.

Jan 1, 1971

By M. K. Mohanty

A modified coal flotation characterization procedure, referred to as the Advanced Flotation Washability (AFW) technique, has been developed which, compared to traditional procedures, provides a more accurate prediction of the optimum separation performance achievable by a froth flotation process. The AFW procedure uses a vertically-baffled flotation column which provides enhanced selectivity among particles of varying degrees of hydrophobicity due to a plug-flow environment and an improved carrying-capacity environment. In fact, the separation performance of the traditional procedures was enhanced by increasing the possibility of operating under improved selectivity conditions. The separation performance provided by the AFW procedure was superior to that obtained from multiple cleaning stages using commercially-available flotation columns under both kinetic and carrying-capacity limiting conditions.

Jan 1, 1997

"Above ground, elevated belt conveyors with span >200m between support points can cross valleys, rivers, forests and buildings with minimal footprint. The Cable Bridge Conveyor is a new type of suspension bridge based belt conveyor system that has long span between support points. It combines typical belt conveyor and the improved simple suspension bridge to form a conveyor bridge. The improved simple suspension bridge places a widened bridge deck directly on suspended cables, without the need for high truss towers. The benefits include reduced cost and increase aerodynamic stability compared to conventional suspension bridges. The Cable Bridge Conveyor’s compatibility with current belt conveyors allows the versatility in application. INTRODUCTION Belt conveyor is a ubiquitous material handling system. Conveyors can be placed directly on ground or elevated above ground by support structures. Considerations of cost, design, environment, civil work, safety and process requirements are all factors in choosing the ground based or elevated conveyors (1). The ground based conveyor has the lowest structural cost, where the conveyor is laying on an existing road. Maintenance access is easy and straight forward. Compared to the ground based conveyor, the elevated conveyor can cross existing buildings and structures, give passage to traffic beneath the conveyor, has smaller footprint, and requires less civil work to pass mountainous areas. The drawback of the elevated conveyor is higher structural cost, which can be compared with savings in civil work and other benefits. Conventional elevated conveyors are supported by rigid truss type structures, with typical span of 15m to 25m between concrete support bents or steel trestles. Triangular truss, using steel pipes instead of hot rolled steel sections, is more efficient. The typical span of triangular truss supported conveyor is around 30m to 40m, while the weight is about 10% less than conventional box truss with shorter span (2). Long span elevated structure based on suspension bridge is another step forward in increasing the distance between support bents, reaching 100m~400m and beyond. The very wide distance between support points of an elevated conveyor offers unique benefits. The conveyor can cross rivers, valleys, highways, forests and other obstacles with minimal footprint and reduced civil work. The versatility from long span conveyors makes bulk material transportation over previously impossible terrains now a feasible option."

Jan 1, 2015

By C. Villa Diniz

It is proposed that battery grade Mn02 can be produced directly from a manganese ore from Azul Mine in Brazil, by leaching with HCI to remove heavy metals selectively. We are working to find a way of selectively separating Cu, Ni, Co, Pb and Fe from the resulting acidic manganese chloride solution, to detoxify it and produce marketable chloride solution. Chelating ion exchange resins are proving more promising for this separation than solvent extraction with commercially available reagents. Results from batch and column ion exchange tests that characterize the behavior of copper, nickel, cobalt, lead and iron are reported.

Jan 1, 1999

The fundamental objective of mine plans are usually to maximize the mine profit by extracting ore at the lowest possible cost over the mine life while some technical constraints are satisfied. Since the costs associated with the operation of trucks and shovels as resources are significant, determining the optimum number and allocation of these resources is an essential issue. This paper presents a Mixed Integer Linear Programming (MILP) model to determine the optimum number of shovels and trucks required to meet the short-term plan?s goals. Also, the model takes into account the allocation of trucks and shovels to mining faces. This model minimizes operational costs, while attempting to meet the production demand and to satisfy technological constraints. This paper also analyzes the operations of trucks and shovels in an open pit mine using ARENA simulation software.

Jan 1, 2012

By G. Bonifazi

Certain deposits of incoherent materials which are near the surface and exploitable by open-pit mining may be characterized in real time before they are mined through an analysis of ground-surface imagery. If the slice to be stripped is not overly thick, in fact, surface texture and color properties may be extrapolated to its entire thickness. Image analysis techniques to process ground surface images acquired in situ (or in the laboratory shortly after their acquisition) which yield pattern vectors representative of RGB color component distributions and HSB texture parameters have been developed. The techniques were applied to a mineral sandy ore deposit containing three different lithotypes. Geostatistical analyses showed that the data used to characterize the lithotypes were reliable. The correct recognition of the lithotypes was carried out using a multi-barycenter classification algorithm. Such in situ image-analysis procedures open the way to the proper selection of the ore to be mined, or the proper way for run of mine (r.o.m). processing, or the appropriate blend to be processed before or at the same time as the mining process itself is enacted.

Jan 1, 1999

By A. H. Leuschner, P. J. Kruger, J. Kruger

INTRODUCTION This paper deals with some practical aspects of the use and interpretation of dosimetric methods for assessing the exposure of workers to natural uranium. Consideration must be given not only to the scientific value of the method of dosimetry, but also to the practicality of the method in the particular working environment. It is generally accepted (IAEA, 1976) that uranium does not present a hazard during the mining and extraction processes up to the final concentration stage, that is precipitation as ADU or calcining to the oxide. Further processing (e.g. conversion to oxides, fluorides, etc.) is generally associated with the nuclear industry. It is customary for uranium processing facilities to be managed according to industrial norms rather than according to those applied for the purpose of radiation protection. This is mainly because of the large quantity of material to be processed and the fact that uranium is considered to be of a low radiotoxicity. Although ventilation is used to some extent, provision is not made for the same level of protection as would be required in a radiochemical facility. It is typical in such a plant to find that the process itself may be enclosed and ventilated, but the ventilation is inadequate to cope with an accidental release of material. The working environment is poorly ventilated, sometimes only by natural ventilation, and one frequently finds areas with high airborne dust levels, designated as mandatory respirator areas. Protection of personnel is dependent on personal protective equipment. Radiation protection is not of prime concern and personnel are not specifically trained in this subject. It is in this type of environment that acceptable monitoring procedures and personnel dosimetry must be established. The effectiveness and practical application of the dosimetry must also be judged against this working environment. DOSIMETRIC TECHNIQUES The methods available for assessing personnel exposure, whether it be in terms of chemical or radiological hazard, include urinalysis, faecal analysis and [in vivo] monitoring. Faecal analysis does not present itself easily as a method for routine use. Techniques for [in vivo] monitoring have been developed recently and as expensive instrumentation is required, it is not generally available. That leaves urinalysis as a dosimetric technique for routine use, and it is probably for this reason that urinalysis is still widely used. Guidelines for the interpretation of urinalysis results, as originally provided by Neuman (Neuman, 1950), are still used in practice, even though it has become clear that this method has severe limitations as regards the assessment of the dose as a result of the intake of class W or class Y compounds (Alexander, 1974). Typically a level of 300 µg [U/C] urine can serve as an indicator of an acute exposure (above which chemical damage to the kidneys may occur) and a level of 100 µg [U/C ] urine can serve as an indicator for an investigation. Such levels are determined and are used in conjunction with several factors, such as mode of intake (ingestion or inhalation), solubility of compound (D, W or Y), means of intake (acute or chronic), environmental monitoring results and frequency of urine sampling. Since the ICRP concept for internal radiation limitation changed from that of the critical organ, i.e. the single organ of greatest significance under the circumstances, to that of effective dose equivalent, i.e. account being taken of the total risk due to the exposure of all tissue, the maximum permissible organ burden (MPOB) was replaced as secondary dose limit by the annual limit on intake (ALI) (ICRP, 1977). The ALI values are calculated from the committed dose equivalents of the various organs, and are used to determine organ burdens, which are then used to interpret the dosimetric results. Using the ICRP model (ICRP, 1979), a comprehensive calculation was made by Johnson (Johnson, 1980), giving organ burdens and excretion data in terms of intake for acute and chronic exposures for different categories of uranium compounds. The question arises as to what extent the direct measurement of intake can be utilised as a method of dosimetry. This will require a method of personal intake measurement for each individual worker, with both ingestion and inhalation being taken into account. A measurement of

Jan 1, 1981

By L. I. Gyrskia, Y. V. Andreev, T. N. Greiver, G. V. Petrov

Traditionally, chromite ores are regarded exclusively as a monomineral raw material for extraction of chromium. The results of the investigations indicate a wide range of PGM in the Ray-Iz chromites, amounting to 1-3 ppm PGM. The study of products of primary gravity concentration from heavily and lightly disseminated ores (Tsentralnoe deposit, Ray-Iz block), showed that the platinum-group minerals are concentrated in the tails and slimes of the processed products, containing 10-30 ppm total PGM. Preliminary data make it possible to conclude that an in-depth study of the platinum mineralogy of the Ray-Iz block chromite ores is necessary to develop a process that will produce both chromium and the PGM.

Jan 1, 2000

By A. L. de Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS). Biologically produced hydrogen sulfide has economically very interesting application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By Jon J. Indall

I. INTRODUCTION The challenge of moving the use of nuclear energy from military to civilian use was first issued by President Dwight Eisenhower in his December 8, 1953 “Atoms for Peace” speech delivered at the United Nations. Eisenhower stated: “The United States knows that if the fearful trend of atomic military build up can be reversed, this greatest of destructive forces can be developed into a great boon, for the benefit of all mankind. * * * * The more important responsibility of this Atomic Energy Agency would be to devise methods whereby this fissionable material would be allocated to serve the peaceful pursuits of mankind. Experts would be mobilized to apply atomic energy to the needs of agriculture, medicine, and other peaceful activities. A special purpose would be to provide abundant electrical energy in the power-starved areas of the world. In the 1950’s and 1960’s, the Atomic Energy Commission promoted the use of nuclear power as the answer to our nation’s energy problems. Nuclear power would provide energy too cheap to meter. The utility industry responded and numerous plants were planned with over one hundred constructed from the 1970’s to the 1990’s. Capital costs for nuclear power plants escalated due to permitting changes and public opposition, and the Three Mile Island incident caused new nuclear plant construction to cease. Today, we once again are experiencing a nuclear renaissance. Concerns over global warming and rapid projected increases in the demand for electricity have caused many nations to begin construction of new nuclear fleets. The price of uranium to fuel these reactors, which had dropped to an historical low of $7.10 in 2001, has surged to $56.00 as of October 2006. This paper will review some of the social, environmental, and government issues that are all playing a role in the resurgence of the nuclear fuel industry.

Jan 1, 2007

By Kyle A. Perry, Ethan A. Steward

The mining of underground coal presents several hazards for miners, including the risk of an explosion fueled by methane gas and coal dust. Methane gas, produced during coal formation, can continuously leak into old workings and build up through its lower explosive limit. Underground coal mines are required to maintain safe conditions, either by ventilating old workings or sealing them off using approved methods. Seals must be designed to withstand instantaneous pressures for a minimum of four seconds. A design strength of at least 50 pounds per square inch (psi) is required for atmospheres monitored and maintained inert, 120 psi for non-inert or not monitored, and greater than 120 psi for special cases. Due to the high cost and testing environment availability, most mine seals are designed through calculations and computer modeling and not subjected to full-scale testing in a representative environment. High pressure is not the only threat that mine seals may be exposed to. During an underground explosion, pressure waves and gas expansion may propel common mine items and objects to a high velocity, generating enough energy to damage mine seals and reduce their strength. Damaged mine seals may fail to contain their rated pressure, allow high pressure gas and fumes to vent through the seal during an explosion, or allow gasses to leak through the seal later after an explosion has occurred. This paper examines the effects of high velocity impacts of common mine materials and items on a reinforced mine seal rated to 120 psi.

Jun 2, 2023

By C. D. Iles

The philosophy used in designing and writing Duval's Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). FED is a method by which predesigned pushbacks are sequenced into an optimized period-by-period design that can be directly utilized in daily operations as well as intermediate and long range planning. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system; it is in operational use.

Jan 1, 1981

By Meisam Ghiasi, Mohammadreza Khalesi, Mahmoud Abdollahy

In the current research, isothermal experiments of kinetic analysis were performed at different temperatures (800–1050 °C) and particle sizes (885 to 10,763 μm) to investigate the calcination kinetics of high-purity limestone. Thermal analyses were carried out in a zirconia crucible, 1 cm in height, for different temperatures and particle sizes. The reaction rate coefficients were varied in the 2.2 × 10−5-1.62 × 10−3-m0.6.s−1 range. Moreover, various isothermal kinetic analysis methods were applied to assess the decomposition mechanism and the calcination function governing the process. The modified shrinking core model was found as the best representation of the high-purity limestone kinetic data. The activation energy was evaluated using the Arrhenius curve, and an average value of 86 kJ.mol−1 was obtained.

Sep 15, 2020

By John A. Meech

In many multiple-sulphide ore flotation processes, it is desirable to concentrate each of the various valuable minerals into separate products. Although there are a variety of techniques and chemicals which can be employed to produce efficient separation, two basic types of flotation circuits are used: The Differential Flotation Circuit and the Bulk/Selective Flotation Circuit. Figure I depicts these two circuits in their most simplified form for the production of two concentrates and one tailing product. If three or more valuable minerals are present in an ore, a variety of combinations or extensions of these two basic flowsheets may be used. There are many examples of the successful application of both circuit types with ores containing similar minerals. Each ore must be tested individually to decide on which circuit is best. However, the following general statements can be made: 1) The differential circuit will have higher capital and operating costs than will the bulk/selective circuit due to higher rougher capacity requirement. 2) The differential circuit will achieve better separation than will the bulk/selective circuit since it is usually easier to reactivate a depressed mineral than it is to depress an already active mineral. If the deactivation problem with the bulk/selective circuit . . in can be overcome, there is a clear economic argument for its use

Jan 1, 1977

By S. A. Suhler

The detection of hazardous geological anomalies through remote sensing techniques is the subject of current research efforts sponsored by the U.S. Bureau of Mines. In this review, hazardous geological anomalies are discussed with respect to the "view" presented along with potential operational concepts for each technique. The design and development of a borehole radar is described with emphasis on the potential range and resolution capability of the system under realistic underground conditions. Results of field tests at two coal mines and at a hard rock future subway location are presented.

Jan 1, 1978

By R. A. Ynchausti

In January 1993, Pyramid Resources began implementation of a supervisory expert control system at a U.S Cu concentrator. The objective of this control system was to improve plant profitability through unit operation optimization and integration. This paper documents the key aspects of the project, including: economic and associated benefits, system architecture, concepts of implementation, process control strategies, practical aspects of implementation and conclusions. The implementation of expert control at this concentrator has resulted in an estimated benefit of $50,500 per day. This is a net result of improved tonnage, reduced reagent consumption, improved concentrate grade and reduced energy per ton produced.

Jan 1, 1995

By Ian Hooper, Alan Winter, Stefan Sadokierski, Craig Covil

The existing Tappan Zee Bridge was built in the late 1950s and has been working over its design traffic load for some time now. A new project, which is being jointly sponsored by the New York State Thruway Authority and Metro-North Rail Road, is looking at new alternatives to provide new road and rail crossings of the Hudson River. These include 2 to 5 mile and potentially longer tunnel crossing options that include hardrock TBM and EPBM opportunities. The paper describes the project needs and tunnel concept design work done on some of the alternatives. It also relates to the current EIS process for the project and talks about a possible double-stacked tunnel option. It also talks about the geology and environmental constraints relating to tunneling and provides and introduction to the tunnel ventilation work necessary for tunnel crossing of this magnitude. It does not report on the bridge engineering options being evaluated.

Jan 1, 2005

By Pelin Altinkaya, Maria Leikola, Jussi Liipo, Mika Haapalainen, Mari Lundström, Eero Kolehmainen

With decreasing ore grades, the tailings of mining operations are becoming of increasing interest as metal-containing secondary raw materials. The objective of the current work was to investigate chloride leaching of gold, copper, cobalt, nickel, and zinc present in the flotation tailings. In the current study, the effect of cupric ion as an oxidant (0–50 g/L) and NaCl (150–250 g/L) on metals extraction was investigated. The other parameters, such as pH (1.8), temperature (95 °C), solid/liquid ratio (25%), oxygen feed rate (1200 mL/min), leaching time (24 h), and stirring rate (950 rpm), were kept constant. Gold dissolution rate was shown to increase with increase in cupric ion concentrations up to 50 g/L. Also, increase in NaCl concentration up to 250 g/L increased gold extraction. Majority of the copper present in the flotation tailings could be dissolved with all the all solutions investigated. The other base metals, cobalt, nickel, and zinc extractions were also shown to increase with increase in the cupric ion and sodium chloride concentration. However, even in the absence of cupric ion addition (t = 72 h, 250 g/L NaCl), the final extraction of Cu, Ni, Zn, Co, and Fe increased up to 98, 93, 83, 76, and 80%, respectively. This shows the power of inherently originating oxidants present in the tailings. Furthermore, the solid analysis of the leach residue indicated that leaching the flotation tailings in pure NaCl may result in partial gold dissolution. The results demonstrate that significant amount of metals present in the tailings could be extracted even with only NaCl as added chemical in the presence of oxygen feed, oxidizing agents originating directly from the raw material. This can provide an advantageous cyanide-free method for extraction of metals from very low-grade tailings with low chemical consumption.