Search Documents

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2018

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2017

By James B. Lincoln

The Schaffer linear kimberlite complex and Aultman kimberlite diatremes comprise a major part of the State Line kimberlite district of Colorado and Wyoming, which encompasses approximately 200 sq mi (500 km2). The district is located along the eastern flank of the northern Front Range and is underlain prin- cipally by Precambrian granites (approx. 1.4 b.y.) which have been intruded into an older (approx. 1.75 b.y.) metamorphic complex. The kimberlite occurrences are Devonian in age and are related to older Precambrian linear structures. The Schaffer kimberlite complex is a dike or fissure system with enlargements or blows developed at the intersections of cross faults; the two Aultman occurrences are diatremes. Kimberlite within the Schaffer complex is predominately grey to green phlogopite-calcite kimberlite breccia and tuffisitic breccia. Carbonate is abundant in some phases. Inclusions of host granite are common and locally abundant. Upper mantle peridotite, pyroxenite, and eclogite and lower crustal granulite xenoliths are present at many localities. Four phases of tuffisitic kimberlite breccia occur in the Aultman diatremes. These breccias are characterized by high carbonate and serpentine contents. Xenoliths of upper crustal granite, lower crustal granulite, and upper mantle assemblages are abundant locally. Lower Paleozoic sedimentary rock xenoliths are also abundant in the Aultman diatremes but are absent in kimberlite of the Schaffer complex. From 1979 through September 1982, Cominco American, Inc., conducted geologic mapping, petrographic studies, geophysical surveys, geochemical surveys, and auger drilling in the Schaffer-Aultman project area as part of an extensive evaluation program of kimberlite occurrences. Forty bulk samples (approx. 8,000 metric tons) were excavated from the occurrences and then were processed for diamonds at Cominco American's heavy media separation and diamond recovery test plant at Fort Collins, Colorado. Indicated grades from the Schaffer and Aultman kimberlites range from approximately 0.5-1.0 carat per 100 metric tons and as such, the occurrences do not appear to approach economic viability at this time.

Jan 1, 2013

By Jorge Gutierrez C.

CODELCO-CHILE, the world's largest copper producer, began an integrated study of the informatics situation in the corporation at the end of 1980. As a result, a five years strategic Systems Plan was elaborated and approved by top Corporate management. Main points in this plan were: a systems architecture with information integration to the top level management; a higher degree of information technology in the production areas, an optional systems development resources utilization and a high profitability of the plan itself. During the study phase a series of theoretical definitions were fixed and used as a basis for the plan's design. A "common systems" approach was chosen as the development strategy instead of corporate systems or separate divisional efforts. Top management should be highly involved in the revisions of the plan, as well as qualified users should be chosen as project managers. The systems architecture should grant the information integration to the corporate level, in order to support an integrated planning and administration environment for the corporation. A total of 15 projects were defined, involving 570,000 man-hours and shifting the development efforts towards the production and production services areas. The paper presents a critical evaluation of the whole process, showing its good and bad aspects and a positive global balance. It also points some suggestions and hints to any corporation who wishes to get involved in a similar experience.

Jan 1, 1989

By C. E. Seaman, H. Jiang, S. Klima, T. W. Beck, Y. Zheng

Respirable coal dust has been long recognized as a leading cause of multiple lung diseases. Efforts aimed at reducing dust concentration in underground mines have been made, but increases in coal workers’ pneumoconiosis incidence rates over the last 20 years among U.S. miners are concerning. Dust deposition and water spray suppression are two types of dust removal mechanisms in underground mining activities. In this study, laboratory tests were conducted to investigate the respirable dust decay characteristics during deposition and suppression processes in a confined dust chamber. Dust concentration and size distribution were monitored continuously throughout each 60-minute test. A number-basis particle size distribution was used for analysis to capture the changes of smaller size fractions within the investigated dust sample. This study found that around 62.1% of respirable dust particles were deposited at the end of the deposition test. In addition, the final deposition rate for very fine particles can be less than 20%. The results from the suppression test indicate that larger particles were removed quickly; however, sub-micron particles remain suspended through the 60- minute water spray, and particles under 0.5 µm can be considered irremovable dust under single-spray operation conditions. This study also observed the resuspension of a significant amount of sub-micron particles by the water spray. The results of this study provide basic information for improving dust control strategies and can be utilized to improve the water spray performance for reducing airborne dust levels.

Mar 2, 2022

By Earl Rau

Introduction Will cogeneration be a major power source in the future? The location of electric power generating plants has changed. In 1900, more than 50% of electricity was generated by industrial plants. Since then, industrial plant generation of electricity greatly decreased to 17% in 1950 and to only 3% in 1980. Changing economics in electric power generating costs, though, may allow cogeneration to reverse this trend. Cogeneration has been defined as the simultaneous production of electric (mechanical) and thermal energy from a single energy source. Some applications are considered to be byproduct generation of electricity from industrial, thermal operations. Cogeneration is not new to the mining and minerals industry. Smelters and steel mills have used waste heat to generate electricity. Public Utilities Regulatory Policies Act of 1978 The potential for increased industrial cogeneration of electricity is related to the March 9, 1978 enactment of the Public Utility Regulatory Policies Act (PURPA). The US Supreme Court ruled that PURPA is constitutional. The court upheld requirements that utilities interconnect to cogenerators. It also ruled that 100% of avoided costs be used as the guideline for electricity sales by a qualifying facility (QF) to a utility. The state of New York established a floor price $0.06/kWh for electricity sales from a QF to a utility. It is obvious, then, that a cogenerator must first establish price and then become a qualifying facility in order to sell electricity to a utility. Proposed cogeneration plants The estimated industrial cogeneration potential for the years 1986 to 2000 is 9500 to 25,000 MW. Industries represented in this cogeneration estimate are pulp and paper, petroleum, chemicals, food, textiles, rubber, plastics, steel, lumber and wood, cement, glass, metal fabrication, and industrial parks. A cogeneration plant has been proposed for the Union Carbide chemical plant in Institute, WV. A steam turbine/generator would be installed to replace the pressure-reducing valve in the 2.7 MPa (400 psig) header. Scott Paper Co., Mobile, AL, proposed a cogeneration plant using a coal- and wood-fired boiler and a turbine/generator to produce process steam and electric power. A cogeneration system has been proposed for a large oil refining plant. A pulverized coal boiler would produce high-pressure steam to operate a turbine, generator. The exhaust steam from the turbine will go to the process and an existing turbine. Kansas City, MO's Armour meat-processing plant has proposed a cogeneration plant. This proposal is to use a natural gas or oil-fired, gas-driven turbine and a generator. The waste heat from the gas turbine would go to a heat recovery boiler for use as process heat. Dade County, FL is implementing a central energy system to supply electricity, air conditioning, and domestic hot water for five buildings in downtown Miami. The cogeneration system is to provide flexibility, to optimize fuel use efficiency while serving the variable thermal demands. Generation of electricity from municipal waste is not considered to be a cogeneration process but is covered by PURPA. Special considerations are provided for waste/electric power generation to encourage the development of these systems. ?

Jan 7, 1987

By G. W. Heunisch

G.A. Carmody and L.B. Anderson We wish to comment on the paper by G.W. Heunisch (MINING ENGINEERING, January 1987), which raised several important points regarding treatment of acidic waste waters. This paper confirms, in part, tests carried out by Allyn Corp. Allyn is the manufacturer of the proprietary product Alka-Ment, one of the materials that Heunisch tested. The first point is the extreme sensitivity of the sedimentation rate on the nature of the treatment material used. This apparently results from differences in nucleation of the metal hydroxides, and is consistently higher for Alka-Ment. This decreased sludge volume is also observed when Alka-Ment is combined with flocculants, such as organic polymers (see Table 1). Our second point is to emphasize that Heunisch's work shows how dependent the sludge volume is on pH. It is common practice to overtreat AMD by raising pH to 9 or 10. This practice, in addition to being wasteful of material, actually decreases the density of the resulting sludge, probably by creating charged particles that do not readily coalesce. When treating with Alka-Ment, we recommend that the treatment be monitored by testing both pH and dissolved iron. For both tests, it is important to allow adequate time to elapse between treatment and measurement, so that dissolution of alkali, aerobic oxidation of iron, and precipitation of the metal hydroxides are nearly complete. Our tests have indicated that from 30 minutes to one hour is commonly required. Only in this way can a minimum pH be attained, with adequate treatment, denser sludge, and lower treatment rates achieved. Thirdly, Heunisch correctly recognizes that ASTM titration of Alka-Ment does not reflect the true treatment value available in a unit of Alka-Ment. Our work at Allyn indicates this is a most important consideration when evaluating various materials for the treatment of acidic waste waters. While we were unaware of Mr. Heunisch's work, we welcome comparisons between Alka-Ment and any competitive products readily available for field use. Allyn has hundreds of hours of laboratory and field data we are ready to share with interested parties treating acidic waste water.

Jan 9, 1987

By J. Cole

The Morenci concentrate leach plant construction was completed and successfully commissioned in October 2007. The plant was designed to operate at medium temperature, 160ºC and pressure, 2,100 kPa. The concentrate leach plant utilized many innovative design features. This paper examines the first year?s operation, the challenges, the successes and the lessons learned. The future plans for Morenci concentrate leaching will also be presented.

Jan 1, 2009

By O. B. Bucklen

The Coal Research Bureau of the School of Mines at West Virginia University, using a modified design of a Russian flotation device, was able to obtain a clean coal product containing 7.64 percent ash with 94 percent yield and 97 percent coal recovery. This favorable performance was obtained with the semi-pilot scale flotation cell operating as a simulated three stage unit on slurry taken from the fine coal circuit of a coal preparation plant. This experimental device, consisting of a sheet metal cyclone-like unit mounted on a U-shaped uplift pipe, uses a combined flotation and cyclone action to beneficiate the minus 14 mesh partially cleaned feed product. In addition to providing comparable analytical results, the airlift-cyclone possesses other attractive features among them being a low capital expenditure, utilization of moderate plant floor space, efficient "operation on high density feed slurry, and absence of moving parts.

Jan 1, 1964

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By K. J. Ma, L. Ma, J. Stankus

The paper’s intent is to evaluate pumpable foamed cementitious mine seal material by determining the shear strength of a generic foamed cement in the laboratory. The tests were conducted on three scales: small-size specimens, consisting of cylinders 4 in. in diameter or 3-in. prisms; double shear medium- size specimens, measuring 13 in. by 10 in.; and large-size specimens, measuring 6 ft by 4 ft by 4 ft. The small-specimen shear tests resulted in average peak and residual shear strengths of 128 psi and 56 psi, respectively. These values are fairly consistent with published shear strengths of foamed cementitious material. However, the other two types of shear tests did not achieve the shear strength of a typical pumpable foamed cementitous mine seal material. Based on the test results, the paper concluded that the structural analysis of cement foam seals should be based on their residual shear strengths, approximately 20 psi, determined from small laboratory-scale tests of the cement foam/concrete or rock interface, and not be based on their peak strengths.

Jan 1, 2015

By Ben E. Adams

The Duval Corporation Sierrita copper and molybdenum mining complex is located approximately twenty-three miles south of Tucson, Arizona. The original open pit mine, Esperanza, was put into operation in 1958 and utilized one tailings dam until the Sierrita operation began in 1970, and a second pond was started. Both tailings operations continued to be operated separate and independently of each other until 1977, when the Esperanza Mill was temporarily shut down, and the Esperanza Tailings Dam was retired from service. Except for short periods of use, no new tailings were put on the surface. With the reactivation of the Esperanza Mill in 1979, the Esperanza tailings were combined with the Sierrita Mill tailings and put on the Sierrita Dam, leaving the Esperanza Dam in a retired state.

Jan 1, 1984

By James L. McGregor

St. Joseph Lead Company has been paying incentive bonuses for well over 40 years. In 1958 almost half of St. Joe's 1,860 employees in Southeast Missouri received some form of incentive bonus in addition to their guaranteed wages. There are very few payroll jobs in St. Joe s Southeast Missouri organization that lend themselves to a reasonably good measurement of production or quality, or both, where an incentive bonus is not paid. The term "Incentive Bonus" is used to differentiate betwen bonuses that are based on quantity or quality of work, and those that are merely additional pay of a standard amount per hour or day because of an employee being temporarily assigned to some unusual task, An employee temporarily assigned to a job where the working conditions make the job performance unusually difficult or where a special skill is used is often given a bonus of some standard amount per hour or shift in addition to his usual rate. This is merely a convenient way of paying something extra without disturbing the normal rate structure. Actually, it is differential pay similar to that almost universally paid for evening and night shift work. Bonuses of that type are not being considered in this paper. The basic reason or theory for paying incentive bonuses 9s to get improved production at lower cost, Unfortunately, it is often difficult, if not impossible, to find a yardstick by which it can be definitely proved that a particular bonus plan is accomplishing its purpose, It becomes, then, a matter of judgment on the part of management personnel as to the value of the bonus plan. The fact that St. Joe Lead Company has continued to pay bonuses for over 40 yews and has increased the number of bonus schedules used attests to a definite belief that they are beneficial to the company's successful operations.

Jan 1, 1960

By J. E. Sepulveda

Tar sand deposits in the. Stare of Utah contain more than 25 billion barrels of in-place bitumen, Although thirty times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion barrels), The term "tar sand" refers to a consolidated mixture of bitumen and sand, Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water extraction process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique., Experimental results indicated that, for a given tar sand sample, percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage, These variables were identified by means of an experimental, factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence gathered in this investigation seems to indicate that a hot-water extraction process for Utah tar sands would allow for the efficient utilization of this important energy resource.

Jan 1, 1978

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The conventional rare earth element (REE) industry has historically sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive REE concentrations. These deposits are extremely uncommon, particularly in the USA. Given the criticality of these materials and the need for sustainable domestic supply, the current research seeks to leverage other autogenous processes that lead to concentrated REE resources. One such process is the generation of acid mine drainage (AMD). AMD is very common in many coal mining districts and results from the exposure and oxidation of pyrite during mining. During the generation and migration of AMD, liberated sulfuric acid mobilizes several metal ions including REEs. Treatment of AMD is required under U.S.C §1251, the Clean Water Act, and often consists of neutralization, oxidation, and metal hydroxide precipitation. To investigate the deportment of REEs during this process, a field sampling campaign was undertaken, whereby the concentration of REEs in AMD and AMD precipitates was measured directly. In the nine sites evaluated in this study, the REE concentrations of the precipitates varied from 29 to 1286 ppm with an average of 517 ppm among the sampled sites. The individual elements were enriched compared with the associated bulk Northern Appalachian (NAPP) coal material by factors ranging from 3 to 15. Furthermore, the distribution of REEs in all precipitate samples favored the heavy REEs (HREEs) when compared with traditional REE ores. This research represents the first part of multi-part research endeavor to characterize, classify, and determine the practicality of refining REEs from AMD and its by-products.

By Orlando Oliveros

The Los Bronces Mine and Concentrator, one of the three operating units of Compania Minera Disputada de Las Condes S.A. (an Exxon Minerals Co. affiliate), is located in the high Andes of East-Central Chile approximately 70 kilometers northeast of Santiago at an elevation of 3,650 meters above sea level. (Figure 1). Santiago, the capital city of Chile, is located at an elevation of about 500 meters above sea level and enjoys a very mild climate, similar to some areas of California. At the mine site, however, extremely heavy winter conditions prevail occasionally, with very heavy snow and the resulting snow avalanches endangering installations and people. At the same time, ideal skiing conditions are found at the nearby ski resort of Portillo and Farellones. Mount Aconcagua, the highest mountain in the western hemisphere is only about 55 kilometers further to the northeast of the Los Bronces mine.

Jan 1, 1983

Traditional loading systems have relied for many years on wheel and track loaders, power shovels, conveyor belts, and more recently, hydraulic front shovels. Each has certain advantages and disadvantages, depending largely on job conditions. Hydraulic backhoes were introduced several years ago as still another truck loading option. At first, buckets were small and backhoe use was limited to small earthmoving projects. Now, as backhoes are equipped with shorter sticks and bigger buckets to move larger quantities of earth. The "mass excavation" concept offers an excellent truck loading option in many situations. System Development and Advantages Mass excavation was first used successfully by contractors in site development and highway construction, loading both on-highway and off-highway trucks. Operators were able to take advantage of the excavator's ability to work in poor underfoot conditions and dig in tough materials. The technique was first applied to mining in the kaolin mines of central Georgia. Kaolin, one of the world's most abundant minerals, is used to make paper, paint, ceramics, rubber, plastics, and many other products. Since kaolin clay is slippery when wet, load-out with wheel loaders is very inefficient. Also, kaolin is found in very spotty deposits due to the weathering process involved in its formation. Consequently, draglines are also impractical for kaolin mining since they don't have the mobility to move between clay deposits. In response to these mining conditions and kaolin characteristics, mines began using excavators in mass excavation as early as 1976. They have developed a system that takes advantage of the excavator's •high penetration and breakout force in tight materials; •fast-cycling hydraulics; •ability to work in poor underfoot conditions; and •mobility in comparison to draglines. This loading method has been successful in Georgia's kaolin mines and now can be applied to other mining operations as well. The excavator's ability to carefully dig spotty ore deposits is an asset at uranium mining operations. Any mine can take ad-

Jan 3, 1982

By John W. Reddy

The C&NW Ore Dock at Escanaba, Michigan, is a major terminal on Lake Michigan for iron ore pellets arriving from the Marquette Iron Range located 112 km (70 miles) to the north. In an average year, the terminal handles in excess of 8 000 000 Mg (LT) of iron ore pellets consigned to a number of major steel companies. It is important to the steel companies for both cost control and operating efficiency that each cargo be sampled as accurately as possible in order to determine the physical and chemical properties of the pellets. This paper describes the equipment and operating procedures of the sampling facility and Presents some sampling data.

Jan 1, 1985

By Norman M. Junk

Following the wide-spread acceptance of ANFO as a useful, low cost blasting agent, studies have been made to adequately describe the physical and explosive properties of this material (1). As the quality of the AN blasting prill improved, reliability and sensitivity to initiation were greatly increased and many methods of priming were chosen from the standpoint of economics with little appreciation for the need to initiate so as to obtain the most efficient detonation. Under certain conditions, ANFO could be initiated with primers no more powerful than a No. 8 blasting cap (2). Research on primers for ANFO followed and it was demonstrated that this blasting agent was subject to extreme transient velocities upon initiation with wide variations in energy output depending upon the nature of the primer. For these reasons it was shown that powerful priming was economically justified (3). These studies helped to define the properties of an effective primer and the guides for its efficient use. In the vast surface coal mining industry, technological advances in earth moving equipment were paralleled by the development of larger and larger borehole drills (4). Even though ANM) was the major blasting agent used in this industry, investigations of priming techniques in these larger boreholes was almost non-existant. In 1962, Mr. Cleon Woolsey of Enos Coal Company disclosed to the industry that dramatic improvements in blasting production could be achieved with new priming and boostering methods (5). The research program at the Atlas laboratories was designed to explain these results and extend the study of initiation of ANFO with both high explosives and slurry explosives and to define the principles involved.

Jan 1, 1968

By Hongling Wang, DI WU, Shuai Li, Hui Shu

Isothermal reduction experiments on carbon-bearing pellets of copper slag were investigated by the thermogravimetric method with biomass carbon as a reducing agent. The results indicated that the reduction process of copper slag‑biomass composite pellets was dominated by gas phase diffusion, and the apparent activation energy was 88.44 kJ/mol. In the temperature range from 1000 to 1200 °C, the metallization rate of pellets increased with increasing temperature, and the maximum metallization rate was 78.4%. The optimal reduction temperature of CSBCP (copper slag-biomass composite pellets) was 1200 °C.

Nov 23, 2022