Search Documents

By Eugene W. Price

One of the most important fundamental characteristics of iron ore pellets is their porosity. This importance arises from the fact that the pores are the busy avenues whereby many changes are brought about in the life and form of the pellet from the time it is made until the iron it contains emerges as a molten stream from the blast furnace. As a green iron ore pellet is first heated in the drying cycle of a typical heat-hardening process, the pores act as conduits to allow the escape of steam from the water or vapor from the oil which served as binders to hold the green pellet together. After the release of the steam (or oil vapor) the pores then act as conduits whereby oxygen can enter the pellets to 1) convert magnetite (Fe304) to hematite (Fe203), if appropriate, and 2) promote solid state grain growth between adjacent particles of iron ore. The rate of oxidation and the rate of grain growth are directly related to pore size' and pore size distribution. Rate of oxidation is also directly influenced by length of pore and length of pore is obviously related to pellet diameter. It is well to keep in mind that the heat-hardening process does not harden the mineral grains themselves. What it does is weld them together to change the green pellet from a doughy mass, composed of thousands of tiny individual particles, into a strong, intergrown monolithic structure. In the blast furnace the pores again act as conduits for gases, but in this case they trans¬port reductants such as hydrogen (H2) and carbon monoxide (C0) which remove most of the oxygen from the ore. Rate of reduction is also directly related to pore size and pore size distribution.

Jan 1, 1967

By H. W. Hintze

Coal handling facilities, such as utility plants, coal terminals, ports, manufacturing, processing, etc. Protect themselves against interruptions in coal receipts by maintaining a 60 to 90 day supply in storage. Not too long ago, these storage piles were referred in terms of hundreds or thousands of tons. Today, it is not unusual to have hundreds of thousands or millions of tons in storage. Burn, or shipping and receiving, rates have increased dramatically and storage piles have grown in horizontal as well as vertical dimensions. Fixed systems for delivering and retrieving coal from storage have increased in length and operating capacity and have become highly sophisticated in their operation. With few exceptions, mobile material handling equipment is used to handle all coal beyond the reach of these systems. These machines take excess loose coal from the fixed system to the storage area, place it on the storage pile, compact it, maintain the pile, protect against spontaneous combustion, the spread of fires if they occur, and return the coal to the reclaim system as required, plus many of the small chores around the facility.

Jan 1, 1981

By T. Brozell

"Communities near sand mines and processing facilities in Wisconsin have raised concerns regarding possible exposure to ambient respirable (PM4) crystalline silica. Fenceline PM4 (particulate matter captured with a 50 percent cut size of 4 micrometers aerodynamic diameter) crystalline silica concentration data were compiled at Fairmount Santrol Inc., Mathy Construction Inc. and U.S. Silica facilities. The long-term average PM4 crystalline silica concentrations ranged from 0.05 to 0.45 micrograms/m3 when sample values below the limit of quantification were treated as zeros. All of the long-term average concentrations were less than 20 percent of the Minnesota Department of Health’s and California Office of Environmental Health Hazard Assessment’s PM4 crystalline silica chronic reference exposure level of 3.0 micrograms/m3. The measured concentrations were consistently within the local background concentration range.Air Control Techniques P.C. compiled the sampling data using Thermo Fisher Scientific Inc. Partisol 2000i PM2.5 samplers meeting the requirements of 40 CFR Part 50, Appendix L. These samplers were adapted to capture particulate matter with a 50 percent cut size of 4 micrometers. The use of polyvinyl chloride filters allowed for crystalline silica X-ray diffraction analysis by NIOSH Method 7500. The combined use of adjusted PM2.5 filter-based samplers with Method 7500 crystalline silica analyses provided for a highly sensitive limit of quantification of 0.31 micrograms/m3 of PM4 crystalline silica.BackgroundIn 2005, the California Office of Environmental Health Hazard Assessment (OEHHA, 2005) adopted a 70-year chronic reference exposure level (REL) for PM4 (particulate matter having aerodynamic diameter of 4 micrometers or less) crystalline silica. The REL was extrapolated from occupational hygiene epidemiological studies, essentially all of which were based on in-plant PM4 crystalline silica measurements. No well-established ambient sampling technique for PM4 crystalline silica was available at the time that OEHHA adopted its REL. The personal samplers used for the National Institute for Occupational Safety and Health (NIOSH) Method 0600 in-plant sampling of employee exposure were designed for concentrations higher than ambient levels. The limit of quantification (LOQ) of PM4 crystalline silica on NIOSH 0600 filters was too high for the effective sampling of ambient air."

Jan 1, 2015

By J. Chai, H. H. Sedarat, Gary J. E. Kramer, A. Kozak

Precast concrete segmental lining systems have been gaining widespread use in seismically active areas and a single-pass version of such a system has been developed for use on the Silicon Valley Rapid Transit (SVRT) Project in San Jose, California. The response of tunnel linings to seismic shaking is often predicted using engineering judgment, elastic closed-form solutions and numerical modeling. Such analyses generally assume a continuous structural system and hence do not explicitly model the behavior of the jointed segmental lining. A number of analyses were performed to predict radial and circumferential joint behavior during seismic ovaling and wave propagation. These analyses included a complex, three-dimensional finite element based ground-structure interaction model that incorporates inelastic constitutive soil behavior, cracked concrete properties and no-tension, frictional segment joint surfaces. The paper discusses the results of the analyses and provides guidelines for the design of precast systems in zones of high seismicity.

Jan 1, 2007

By F. S. Knoll

The high tension process which separates materials based on relative differences in surface conductivity has been very successful in recovering non-ferrous metals from municipal waste. Aluminum is by far the largest constitutent of the total non-ferrous metal fraction; accounting for >95% in most localities. Wire and insulation mixtures from industrial wastes have been treated commercially for several years by a high tension process initially developed for use in the iron ore industry. The wire and insulation application was a forerunner of municipal waste dry treatment technology. In the past eighteen months the rotating-drum-type electrostatic separator has undergone extensive testing and development in order that the process might be efficiently adapted to the recovery of aluminum from municipal waste.

Jan 1, 1974

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By F. C. Appleyard

As one of the more important Industrials Minerals, gypsum occupies a significant place in the economy of the United States, particularly in that segment which can be loosely called the Construction Industry. For many years, products made from gypsum have been a major building material, and the usefulness and versatility of these products is such that their widespread use is expected to continue. In 1968, according to U.S. Bureau of Mines statistics, the value of all gypsum products sold in the United States was 405,000,000 - and although this value has dipped from the 1964 high of $ 432,000,000, it is expected to trend upward in the next few years to equal and surpass this figure as the construction industry recovers from its current squeeze of "tight money" and high interest rates. There are many factors to be measured in determining the potential value of any mineral deposit, and how it might fit within its particular industry. What, then, are the qualities which a gypsum deposit must have in order to profitably participate in the four hundred million dollar plus business which is the gypsum industry? First let's consider the geology of gypsum, the geographic distribution of deposits, and the more important factors such as size, grade, capital requirements, and operating cost. Then, an understanding of the uses of gypsum, various types of products, and location of markets would be helpful, along with such other factors as the structure of the industry, price trends, etc.

Jan 1, 1970

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991

By Anibal Gajardo

Because of the Chilean Ministry of Mining's interest in the development of industrial minerals, the Chilean Geological and Mining Service (Servicio Nacional de Geología y Minería, SERNAGEOMIN) has carried out a research program during the last two years to identify projects that represent interesting investment opportunities for small- to medium-scale operations in Chile. Most important of these projects are: (1) Quebrada Lluta aluminum sulphate, for drinking- and industrial-water treatment, with a potential domestic and foreign mar- ket of almost 43,000 tonnes per year and investments of about US$1.8 million; (2) Quebrada Lluta-Quebrada Cardones pumice, for abrasives, filters, fillers, and light- weight aggregates, with a potential market of about 30,000 tonnes per year, and in- vestments of US$2.0 million; (3) El Maule dolomite, for soil conditioner and iron smelting, with a total potential domestic market of some 60,000 tonnes per year, and estimated investments of US$2.0 million; (4) Las Escaleras bentonite, for animal feed, pelletising, and oil absorbents, with a potential market of almost 6,000 tonnes per year, and investments of about US$2.4 million; (5) Laraquete-Carampangue andalucite, for alumina refractories, with a future total domestic and foreign demand of about 15,000 tonnes per year, and estimated investments of US$2-2.5 million; (6) Rio Lía garnet, for fillers and sand-blasting abrasives, whose domestic market represents 10,000 tonnes per year, with investments of US$2.3 million; and (7) Munilque pumice, for building bricks and panels, with a potential domestic market of 250,000 tonnes per year, and investments of US$1.4 million. The development of these projects will represent an important increase and a significant diversification in Chilean industrial-minerals production.

Jan 1, 1999

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

Disruption in critical minerals supply chains has resulted in the evaluation of various types of mineral deposits for critical minerals potential. Much of the study on critical minerals focuses on occurrence and characterization, but little research has addressed what concentrations of critical minerals in a mineral deposit are required to make an exploration target into an operating mine. Understanding the cut-off grades of ore deposits being actively mined is one criterion to determine if concentrations in an exploration target are high enough. Cut-off grade is defined as the minimum amount of mineral contained in a ton of ore that is sent to the processing plant. Among many factors, cut-off grade depends upon the size and type of the deposit and mining operation, the processing technique, and market prices. This research does not aim to define cut-offs for determining if a mineral deposit is economic. Rather, it defines estimates of concentrations of critical minerals that could be considered good enough for further exploration. For example, ~2% total rare earth oxide (TREO) is the cut-off grade for Mt. Pass carbonatite, but 500 ppm TREO could be an exploration target for coals.

Feb 1, 2025

By Dianne C. Marozas

The U.S. Bureau of Mines is conducting research to evaluate the potential for developing an in situ leach mining process that will selectively extract manganese from oxide ores, leaving gangue relatively undisturbed. To accomplish this, a geochemical approach, based on deposit-specific information such as mineralogy and geology, is used to constrain the operating parameters of the system. Among the studies being conducted are (1) leaching experiments to define reaction mechanisms and kinetics, (2) detailed petrologic characterization at the microscopic scale to assess Mn distribution and leaching efficiencies, (3) deposit characterization and evaluation, and (4) development of potential Mn recovery schemes. Data from these studies are being used to develop engineering design information for an in situ mining process. Specific details of the Bureau's research project are discussed, including results obtained to date.

Jan 1, 1991

By R. D. Williams

Several hydrometallurgical leach processes have been recently proposed for the recovery of copper from copper concentrates. These include the Cymet Process of Cypress Metallurgical Processes Corporation, the Arbiter Process of the Anaconda Company, and the Treadwell Process of Treadwell Engineering company(1). These processes and similar processes for recovery of other minerals, have several phenomenological similarities which make their quantitative description difficult at best. These include (a) the presence of more than one phase, (b) non-uniform mineralization of the feed concentrate, (c) surface and diffusional effects, and (d) a particle size distribution which varies with time. Semi-theoretical, rather than purely empirical, treatment of such processes in their developmental stages will result in a better understanding of the physico-chemical mechanisms in effect. This, in turn, will allow reliable process designs to be made on reasonable time scales for reasonable development costs. Once a production unit is built, such an approach will provide straightforward methods for process control and optimization. A research and development effort to determine criteria and procedures for semi- theoretically characterizing such mineral leach recovery processes has been initiated in a joint venture by the Arizona Bureau of Mines and the College of Mines at the University of Arizona. This group has as its task the mathematical characterization of hydrometallurgical leach recovery processes using semi- theoretical mechanisms for the underlying phenomena. The resulting models are experimentally verified and parameterized on the laboratory scale in such a way that they can be utilized with similarity criteria to provide reliable scaleup to production designs. This discussion will be centered around the elements of such an approach and how they fit together.

Jan 1, 1975

By George A. Savanick

The objective of this paper is to review advances in the art of borehole (slurry) mining made by the Bureau of Mines. The introduction gives historical and general background information on borehole mining. The borehole mining concept is defined and justified in terms of economics, health and safety, the environment, and resource conservation. This is followed by a description of the design of a prototype borehole mining tool (BMT) developed by the Bureau of Mines. Included are design drawings and performance specifications. The next section describes the application of the BMT in the extraction of metallurgical coal from steeply pitching seams near Wilkeson, Wash., during 1975-76. The field test showed that the BMT produced coal at the rate of 8 tons per hour (tph) (7,272 kg/hr) from a depth of 88 feet (26.8 m) and was effective in producing coal as far as 15 feet (4.6 m) from the center of the borehole. The data are used as a basis for an economic analysis of borehole coal mining and for the suggestions for the design of a second-generation borehole coal mining tool. The following section describes Bureau efforts in applying borehole mining to the extraction of uraniferous sandstone at Rocky Mountain Energy Corp.'s Nine-Mile Lake site, Natrona County, Wyo. BMT design changes appropriate to uranium mining are described along with production, reliability, and reclamation data taken during 1977-73. The field test revealed that the BMT produced 900 tons (81.8x105 g) of uraniferous sand at an average race of 8 tph (7,272 kg/hr) from a depth of 75 (22.8 m) to 90 (27.4 m) feet and created a cavity 25 feet (7.6 m) in radius. These data are used as the basis for an economic analysis of borehole mining of shallow uraniferous sandstones. Reclamation data included will be the results of backfilling experiments conducted at Nine-Mile Lake during 1978. The most significant of these data were that backfill was emplaced at the rate of 16 tph (14.5x103 kg/hr) and that 90 percent of the material extracted from a cavity can be backfilled.

Jan 1, 1979

By Arash Habibi, Anna Cable, David Loring, Aleksandar D. Bugarski, Logan Ingalls, Calvin Rutter

The results of diesel particulate matter (DPM) monitoring were used by the underground mining industry to mitigate adverse effects of exposure to DPM. NIOSH Method 5040, currently used for ambient and personal exposure monitoring, does not provide needed real-time information. The objective of this study is to develop a methodology for continuous monitoring of DPM concentrations in an underground environment, founded on the application of the Dekati electrical particle sensor (DePS). The DePS, which measures concentrations of submicron aerosol in real time using a diffusion-charging sensor, was evaluated by comparing the results of the concurrent measurements with reference methods at several locations downstream of the diesel-powered equipment. The DePS results were found to correlate well to those obtained by reference methods. However, it was found that dependence of the response on the physical and chemical properties of aerosols necessitates sitespecific correlation factors for the targeted matrices. The site-specific factors for number and mass of diesel aerosols were derived using the results of concurrent measurements with TSI NanoScan, FLIR Airtec, and carbon analyses performed on the concurrently collected filter samples. The results showed that methodology based on compensated DePS measurements would be suitable for continuous monitoring of DPM in underground mining operations.

Dec 1, 2022

By R. Adsero

"In view of the decade long decline in worldwide mine equipment productivity and with heavy economic pressures and survival at risk, improvements for those remaining in the game are essential. The latest Multifactor Productivity data for the US mining industry indicates a continuing descent with Australia on a similar course. The world’s mining industry has a fleet of over 400 large draglines moving billions of tons of material annually. The most efficient use of this equipment resource will provide a competitive advantage to those companies who are committed to improving performance. A dragline monitoring system is a requirement for optimum operations. The monitor reports the facts. Focused actions can change the facts and create improved performance. Analyzing monitor data to build knowledge and create understanding is a beginning. Understanding the key productivity indicators for dragline operations and an effective benchmarking process are the basis for improvement. There is overwhelming evidence that adopting new technologies and concepts including AC drive technology can and will bring about a step change in dragline operating cost with improved production performance.STATE OF THE MINING INDUSTRY A high altitude review of the state of the mining industry provided by a study of multifactor productivity shows a continuation of lower and lower output year on year for the capital and labor inputs applied. The story is sadly similar for both U.S. mining and the Australian mining sector. In fact, according to PwC analysts the worlds mining equipment productivity has declined 20% over the past seven years. (Lumley, 2014) Although the reasons for the continuing decline in mining productivity are varied, the need for improvement is clear. The world’s mining industry fleet of well over 400 large draglines moves billions of tons of overburden and ore (phosphate, limestone, etc.) annually.This discussion will review a few of the tools available for improved productivity in dragline operations."

Jan 1, 2016

By Isa Nozari, Asghar Azizi

The extraction of copper from sulfate leaching liquor was investigated using Acorga M5640 commercial extractant in kerosene diluent. The effects of important factors such as the extractant concentration, contact time, liquor pH, and temperature were examined on the separation factor Cu/Fe and the extraction efficiency of copper. The results indicated that nearly 92.32% copper was extracted from the leach liquor at 10% (v/v) Acorga M5640 concentration, 1:1 aqueous/organic phase ratio, 20 min contact time, pH 2.5, and 25 °C temperature. Also, the further increase in the values determined had no positive impact on the extraction of copper. Under these conditions, the separation factor Cu/Fe was obtained about 29.64. The extraction mechanism was studied applying the plot of log(D) – 2 pH against log [extractant] and it proved the association of two moles of Acorga M5640 for the extraction of one mole of copper. McCabe–Thiele diagram was constructed and a single-step extraction process was found to obtain themaximumextraction. Additionally, thermodynamic datawere investigated and the extraction process was endothermic and non-spontaneous at 298 K (ΔH = 27.05 and ΔG = 15.52 kJ mol−1). Moreover, the loaded organic phase was stripped and 80.94% copper was recovered after 20 min using 10% sulfuric acid concentration.

Jul 31, 2020

By E. A. Wieselmann

In 1970 Texasgulf (Australia) introduced natural gamma radiation logging of drill holes for exploration in the Hamersley Iron Province of Western Australia. Drill hole logs have allowed positive stratigraphic and structural correlations within complexly folded secondary hematite ore deposits and between individual iron ore deposits separated by distances in excess of seventy-five miles. A Neltronics model KPD logging system and gamma-ray sonde are being used to measure the natural gamma radiation of the enriched Brockman and Marra Mamba banded iron formations. The parent banded iron formations are composed of thick, chemically precipitated iron oxide, chert, iron silicate, and carbonate with thin intro-formational clastic horizons. These clastic horizons give a greater natural gamma radiation than the banded iron horizon, and each clastic horizon has a characteristic radiation profile related to its composition and thickness. Because the natural gamma-radiation profile is unchanged during secondary enrichment of the iron formation, the present stratigraphic position of each drill hole can be established and complex folding can be accurately traced in the sub-surface. Gamma ray logging of percussion drill holes has made feasible a significant reduction in diamond core drilling without loss of accuracy. At the same time, it has provided a means of rapid evaluation of complexly folded iron ore deposits.

Jan 1, 1975

By John Hillman

The reconstruction of the British mining industry which began shortly after nationalisation in 1947 continued until well into the 1950s with the support of the Government. This support diminished as plentiful supplies of cheap oil from the middle East made many coalmines un¬economic. The planned rundown which followed was foreshadowed in the 1965 White Paper which outlined the financial measures to speed the closure of uneconomic collieries. The decline appeared likely to continue into the 21st century as the role of coal in UK energy requirements became less and less significant. This policy was well on course in 1973 when the oil crisis led to a complete reappraisal of the position. A Government examination in 1974 of the coal industry then supported the National Coal Board's general strategy of major capital investment as set out in its 'Plan for Coal' (1). Plan for Coal aimed at halting the intended decline in the industry's capacity and restoring it to 120 million tons of deep mined output in 1985. The Plan proposed action along the following lines (a) increase output by major Investment in construction at existing collieries with sufficient reserves to give 13 million tons per annum extra output (b) invest in extending the life of existing collieries by gaining access to additional reserves, to give 12 million tons per annum extra output © by sinking new mines, produce an extra 20 million tons per annum. Figure 1 shows the contribution (2) expected from each of the three sources up to 1990/1. The measures taken were expected to offset the inevitable exhaustion of existing pits and provide the additional 40-42 million tons capacity needed to restore annual output in 1985 to 120 million tons. Parallel to this programme for expansion of deep mined output, opencast mining was to produce 10-15 million tons per annum. A recent review however, indicates that new mines are likely to yield only 10 million tons per annum by 1985, mainly owing to the need for public inquiries into proposals for new mining and the resultant fact that planning approval takes 'much longer than originally expected. Nevertheless the objective of 120 million tons deep mined output by 1985 is still considered achievable of means of a greater contribution from existing mines. This programme was originally estimated to cost 2,-56 million dollars at March 1974 prices, out revised estimates of the cost of Plan for Coal indicate that it may now exceed 6,960 million dollars at mid-1977 prices. Plan for Coal includes a substantial investment in new and reconstructed coal preparation plaints. At mid-1977 prices more than 322 million dollars Ls so be invested in coal preparation projects in the UK, at the rate of, about 70 million dollars a year. This rate 3f capital expenditure has been maintained over the past three years and covers investment in a wide range of coal preparation coals for the power station, coking and domestic markets.

Jan 1, 1978

By M. L. Young

Hindered settling columns are used throughout the minerals industry for both size and density separations. In this study, the performance of a continuous, laboratory-scale hindered-settling column was evaluated for various particle systems. The test variables included solids composition, water rate, and column height column performance was evaluated using partition curves and corresponding performance parameters.

Jan 1, 1999

By Juan L. Yarmuch, Gonzalo Sepulveda

This article presents a novel approach to address the mining width-constrained open pit mine production scheduling problem in the context of medium-term planning. A mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the NPV of the schedule while ensuring enough room for the operation of mining equipment. To tackle the computational challenges posed by large-scale instances of the problem, we propose a method based on variable fixing and horizontal precedence generation. In this study, we apply the developed model to real-world scenarios from Radomiro Tomic short-term mine planning problems such as optimizing the timing of major truck maintenance and the impact of external factors, like the delay in the production of the Chuquicamata underground project. Remarkable improvements are observed with the mining width-constrained model. Specifically, the mining width satisfiability is enhanced from 2 to 60% compared to the traditional open pit mine production scheduling model, underscoring the significance of incorporating these constraints. The proposed method showed good results reaching optimality gaps within 5%.

Mar 28, 2024