Search Documents

By Ray Wood, Rene Sterk, Robin Falconer, Sean Aldrich, Simon Nielsen

"The Chatham Rock Phosphorite project is situated 450 km east of New Zealand at approximately 350 to 450 m water depth. The deposit occurs as a thin layer of phosphatebearing glauconitic sand at the surface of the sea floor and has a thicknesses typically ranging from 0 to 1 m. The sand layer consists of mainly silt and sand-sized sediments, with phosphatised chalk nodules up to 15 cm in diameter. Phosphate nodules were first discovered on the Chatham Rise in the 1950s by a New Zealand Government survey. During the 1960s to 1980s several private and government sponsored cruises explored the Chatham Rise and surrounding seafloor area. A total of 1174 samples were collected over a 600 km2 area with the majority of the samples collected using a pneumatic -or large Van Veen-style grab-sampler.Since acquiring the licence in 2010, Chatham Rock Phosphate Limited has conducted six cruises in two programs in the Project area. A total of 261 samples were collected using a Van Veen grab, box core and grab samples.Sample quality and QA/QC measures varied considerably between the cruises and within each cruise. A critical part of the assessment of the data collected in the Project area was to determine what quality thresholds to use to allow or disallow data to enter into the estimation process. As part of the data verification process, the relative and absolute quality of the data was assessed in as much detail as practically possible. The best samples were those that were collected using the pneumatic grab, sampled the full sand horizon, had a small location survey error and had no other apparent data ambiguities. This paper describes the challenges for mineral resource estimation for an unconventional style of mineralisation using unconventional sampling techniques."

Sep 1, 2014

By Robert L. (Original by) Llewellyn

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment.

Jan 1, 1981

By Keith G. Wallace, Oscar Codoceo

This paper describes the ventilation planning that was per- formed at the Barrick Gold Corporation, El lndio Mine. The El lndio Mine is located at an elevation of approximately 4,000 m in the Andes mountains east of the coastal city of La Serena, Chile. The ventilation planning program consisted of a detailed ventilation survey of the mine and the establishment of a correlated com- puter model. A series of network simulations were conducted to determine the optimum position, size, and configuration of new ventilation raises and main fan exhaust system. Modifications to existing mine infrastructure including; driving of drifts, slashing of airways, and positioning of ventilation controls were examined. Detailed costing information was developed to optimize the location of the new main exhaust raises and fan system. The final ventilation system is expected to increase the mine airflow from the existing 157 m=/s to over 315 mls. This increase was necessary to accommodate an expansion in mine production, diesel equipment utilization, and deeper mine development. Furthermore, the increased airflow was required because of the de-rating of diesel equipment and large air volumes necessary to dilute diesel exhaust at high elevation.

Jan 1, 1997

By T. Y. Yan

A method has been developed to remove calcite from the leaching circuit in the uranium in situ leaching system. The process involves injecting the leachate and a pH control agent tangentially into an inverted cone reactor containing calcite seed catalyst. The leachate can be treated at high throughput to obtain clear effluent containing 5 ppm or lower Ca. Both lime and ammonia are effective pH control agents and consumed according to stoichiometry.

Jan 1, 1983

By P. Bissert, M. Klein, L. Yan, D. Yantek

"Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hrs. One of the main concerns with the use of mobile RAs is the heat and humidity buildup inside an RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in a fully occupied RA must not exceed 95°F. To investigate this issue, the National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4°C (17°F) and the relative humidity (RH) approached 94 %RH. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the average air temperature inside the RA at the end of 96 hours to within 0.6°C (1.0°F) of the average measured air temperature. INTRODUCTION If an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke, or even death. In its 2007 report to Congress, the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) recommended that RAs should be designed to ensure that the internal apparent temperature (a temperature-humidity metric) in an occupied RA does not exceed 35°C (95°F). However, a standard method to determine compliance with this metric does not exist. The heat transfer process within and surrounding an RA is very complex, and is not easily defined analytically or experimentally. To investigate the related issues, OMSHR conducted heat and humidity testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. During the testing, numerous parameters were measured: heat input to the chamber, the air temperature and relative humidity inside the RA, the air temperature in the mine, the mine strata temperatures versus depth, and the airflow inside and outside the chamber. The focus of this paper is on the temperature rise within an RA. TAITherm heat transfer analysis software was used to develop a thermal simulation model of the RA as it was tested in the mine, using the test results as the benchmark. Both sensible and latent heat were used in the test and the model."

Jan 1, 2016

Although grinding mill liner life has been the subject of extensive studies, evaluation of the effect of liner design on power consumption, a far more significant part of total grinding costs, has been less comprehensive. The factors that effect ball mill energy efficiency are reviewed, and attention is then focused on the mechanisms of grinding. The trajectory of the outer row of balls, with different lifting face angles, is derived, and basic recommendations for mill speed and liner configuration are presented.

Jan 1, 1981

By Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Samuel Nowak, Khaled Mohamed, Morgan Sears

Coal ribs present a major safety hazard in underground mines, and there is currently no unified approach for their design in the United States. To tackle this issue, this study investigated the stability of underground coal pillar ribs under development load. Utilizing over a thousand 3DEC models, a framework for calculating coal pillar rib rating (CPRR) was developed. A detailed step-by-step method was outlined for computing the CPRR based on a 3DEC analysis, which was then validated with various 3DEC models, demonstrating a strong correlation between the two models. The results demonstrated that the rib factor of safety (RibFOS) under development load is directly proportional to CPRR, coal mine roof rating (CMRR), and floor strength, and inversely proportional to the overburden depth and rib height. Moreover, a regression equation was formulated to predict the RibFOS based on the aforementioned parameters. Furthermore, empirical relationships were developed between the RibFOS and the applied primary rib support density (PRSD) in U.S. coal mines. To ease the calculations, a stand-alone application, Design of Rib Support (DORS), was developed. This application can be used to assess rib stability and easily calculate CPRR, RibFOS, and PRSD.

Jul 1, 2023

By Akira Ishikuro, Masamichi Shintaku, Futoshi Kusumoto, Takeshi Kudo

"The Bankei-Kitanosawa tunnel that is located in Sapporo, Hokkaido, Japan includes a 450m long section near the arrival point where mudstone which can liquate out natural hazardous materials such as arsenic and selenium exceeding the tolerance stipulated by country as well as weathered mudstone and unconsolidated sedimentary rocks with small overburden and the competence factor less than 1.0 are present. The mucks containing hazardous materials were disposed into the waterproof branch tunnels created from the inside of the main tunnel. The full face early ring closure method was employed to ensure the stability of the tunnel in the low strength rock masses having no stand-up time. As a result, the waterproof tunnels branching off the main tunnel can manage water tightness so as to ensure safety and relief against environmental risks of the hazardous materials. It is also demonstrated that the full face early ring closure method enable construction of the tunnel with a small overburden in the low strength rock masses. INTRODUCTION The Bankei-Kitanosawa tunnel includes a 450m long section near the arrival point where mudstone which can liquate out natural hazardous materials such as arsenic and selenium exceeding the tolerance stipulated by country as well as weathered mudstone and unconsolidated sedimentary rocks with small overburden and the competence factor less than 1.0 are present. In order to overcome the restrictions, the hazardous materials were designed to be disposed into large cross section waterproof tunnels which were newly designed and constructed in high strength and hazardous material free Andesite. The lining for the tunnels was composed of with shotcrete. In addition, full face early ring closure (Sato et al., 2013) was employed to stabilize the tunnel so as to enable safe tunnel excavation in low strength rock masses where a ground arch is deemed unachievable. This paper presents the safe disposal method of mucks which are likely to liquate out natural hazardous materials as well as the full face early ring closure method and its mechanical characteristics."

Jan 1, 2016

By Hakan Uyguçgil, Beril Bayraktar, Adnan Konuk

Mining is one of the industries with the highest risk of occupational accidents in Turkey and globally. The most important feature that distinguishes the mining industry from other sectors is the constantly changing working conditions. The risk of accidents is very high, especially in underground mining, and can happen for several reasons. Therefore, it is essential to carry out all necessary measures in coordination with other disciplines to adapt to changing workplace conditions. The dangers that might occur underground must be determined in advance, controlled at their source, or eliminated since it is critical to take the necessary precautions before the accident. Accident prevention will protect miners’ living conditions by contributing to the country’s economy through reduced labour and production losses. In this research, the data from 13,653 accidents reported in the Karadon Hard Coal Enterprise between 2000 and 2011 were analysed and compared using the Life Table and the Kaplan-Meier methods. Accident records were classified and analysed into four categories: environmentalrelated accidents, equipment-related accidents, person-related accidents, and other accidents. Findings in terms of survival time indicate that environment-related and person-related accidents had the highest risk in Karadon, with equipment-related accidents having the lowest. This study established the reliability of using survival analysis methods to investigate occupational accidents in the mining sector. Given that environment-related and person-related accidents occur in a relatively short period, such as 1 year after starting work, it has been recommended that research be done to improve workplace and occupational safety measures and broaden the training given to miners. Additionally, it has been determined that increasing the use of automation and mechanisation in underground coal mines, combined with developing a thorough equipment safety training programme to raise awareness of the danger, can help prevent person-related occupational accidents caused by the interaction between equipment.

Aug 5, 2023

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

By Jerome F. Sheldon

The earliest recorded history in the use of belt conveyors in the United States is in O. Evans' "Miller's Guide" published in Philadelphia in 1795. Evans defines a conveyor as a "broad endless strap of thin pliant leather or canvas revolving over two pulleys in a case or trough." (Ref. 1) In this definition, pulleys are being used in a bulk material belt conveyor application. Pulleys used in belt drives can trace their origin back to 1200 A.D. In fact, Engineers had considerable experience designing them into drives transmitting greater horsepower than those used in the early belt conveyors. In belt conveyor application, a pulley's purpose is primarily three-fold, 1) support the belt in directional changes, as designed in the conveyor, 2) transmit driving power to the belt, and 3) guide or train the belt. There are various types of pulleys used in belt conveyor systems and these are thoroughly covered in "Belt Conveyors For Bulk Materials" prepared by CEMA, 1966. For our discussion, however, the most common used in belt conveyors are drive pulleys, snub pulleys, head pulleys, tail pulleys, takeup pulleys and bend pulleys. The drive pulley imparts the driving force to the belt and may be located at the head or discharge end of the conveyor, in return strand, or at the tailor loading end of the conveyor. A snub pulley is located near the drive pulley to provide more arc of contact between the belt and pulley for maximum

Jan 1, 1971

By R. Ribeiro

The designers of the new Arafertil concentrator in Brazil provided for complete automatic control of the grinding circuit to meet the operating objective of maximum throughput at a specified grind. Analog control methods were selected because of proven reliability and simple maintenance, and in order to minimize commissioning time and effort. This paper summarizes the step-by-step effort required to progress from local loop control of certain individual parameters to an integrated system capable of achieving the design goal. Emphasis is placed on the practical aspects of commissioning a control system.

Jan 1, 1979

By Robert M. Abrams

The passage of an ore pulp through the froth flotation process results in the production, after dewatering, of a finely divided concentrate. This intermediate product Trust be handled to the subsequent process facilities via belt or other types of conveyors, hoppers, bins, chutes and feeders, and the like, Flotation concentrate has some difficult handling properties such as abrasiveness, sluggishness when moist, or fluidity when dry, These characteristics require the judicious selection or design of handling, equipment and the careful engineering of transfer chutes. It is to the special problems which are encountered in this in-plant handling procedure that this paper is addressed. The methods which will be discussed have beer. developed primarily for the handling of the froth flotation concentrates of copper, leap, and taconite iron ores, but may be generalized, with appropriate modifications, to apply to other similar metallic concentrate&. The controlled feeding of concentrates frog: bins and hoppers is covered alone with some of the techniques used to transfer concentrates from ore belt conveyor to another. Methods are described for unloading belt conveyors into bins or storage tiles, The reclamation from storage piles is also treated.

Jan 1, 1976

By Shakuntala Tudu, Indrajit Paul, Surajit Sinha, Pulibandla Basaveswara Rao, Shaik Mahaboob Basha, Srinivas Dwarapudi

The iron and steel manufacturing sector directly accounts for 7–9% of global CO2 emissions. Raw material preparation, such as iron ore sintering, pelletizing, and cock making, is the major CO2 emitter. As climate change becomes a bigger concern, steel manufacturers need to lower CO2 emissions without hindering efficiency or increasing costs. In recent years, the percentage of iron ore pellets in blast furnaces has increased due to its uniform size, good reducibility, and high tumbler index. Pelletizing is energy-intensive and emits considerable CO2. Around 20% of CO2 emissions during pellet making come from fluxes. In the present work, the authors established a novel CO2- free flux called wollastonite (CaO.SiO2) for sustainable palletization. Pellets with varying percentages of wollastonite (0–6%) are prepared and tested for chemical, physical, and metallurgical properties. Image analysis through an optical microscope is carried out to quantify the phases of fired pellets. SEM–EDS is performed to evaluate the chemical composition of the melt and slag phases. The results showed that the reducibility index (RI) and swelling index (SI) of pellets decreased with an increase in wollastonite dosage. Pellet strength increases with an increase in wollastonite addition up to 1.2% CaO (2.27% wollastonite), and a decrease in strength is observed thereafter. The increase in strength is attributed to the increase in slag bonds. The decrease in strength beyond 1.2% CaO is mainly because of an increase in low melting eutectics and more magnetite content. Pellets with 2.27% wollastonite to get 1.2% CaO showed good physical and metallurgical properties.

Mar 4, 2024

By I. S. Parrish

As noted by McKinstry (1948), "How to deal with erratic high samples is one of the knottiest problems in ore estimation." He described a variety of approaches and methods to alleviate the problem through the averaging and weighing of assay data and by "cutting" or "clipping" of the erratic assays. Bird (1991) elaborated on ways of dealing with the nugget effect (erratics). He listed several procedures for cutting. Bird's list has been reproduced and/or added to by several authors including Vallee (1992) and Stone and Dunn (1993). Missing from each of these otherwise excellent reviews is a definition, description or guideline to recognition of an "erratic," or just where or when cutting is warranted or justified.

Jan 1, 1997

By J. W. Breen

ASARCO Incorporated has upgraded or is in the process of upgrading the Galena mine electrical, pumping, refrigeration, compressed air, ventilation, hoisting and rockburst monitoring systems to allow continued mining and development work on the 1 589-m (5,200-ft.) level and to provide services for projected deeper mining and development. Additionally, a separate lead-silver milling circuit has been added to the silver-copper mill to process lead-silver ore reserves. This paper describes completed and planned improvements made to date on these systems.

Jan 1, 1991

By J. A. Organiscak

This paper describes the research con-ducted on bit wear and respirable dust generation conducted by the US Bureau of Mines (USBM) and West Virginia University (WVU), a member of the Generic Technology Center on Respirable Dust. The USBM investigated wear, energy and dust characteristics of various conical bit designs when cutting rock. WVU studied the functional relationships between wear, cutting force, energy, and dust of one conical bit type when cutting coal. The objective of the USBM study was to identify qualitative bit selection guidelines for cut-ting rock; WVU's research objective was to determine optimum bit replacement guidelines. These research studies both found that bit geometry (a function of bit design and wear) influences energy consumption and dust generation. Bit selection and replacement recommendations are given.

Jan 1, 1995

By Ahmed M. Yousif, Walid M. Abdellah, Galal M. Abdel Wahab, Amal E. Mubark

The present work is concerned with selective dissolution of niobium from Gabal El Faliq concentrate sample by using fluoridefree process. The chemical analysis of concentrate sample revealed the presence of high amount of ZrO2, Nb2O5, Re2O3, and HfO2 assaying 33.6, 1.99, 4.8, and 1.2%w/w respectively. Several economic minerals including zircon, samarskite, fergusonite, and xenotimewere recorded in the studied sample. About 98%of Nb content was selectively dissolved at the optimumconditions of 1:2 concentrate sample: KOH weight ratio, 2.5 h fusion time, and fusion temperature of 550 °C. Organic solvent extraction process using Aliquat 336S in xylene was effectively used for preparing pure Nb2O5 (98.95%).

Oct 22, 2019

By Mike O'Drisooll

There is no doubt, if any existed, that the commercial minerals world has now moved into a new era of unprecedented challenges in the sourcing, mining, processing, trade and use of industrial minerals. Industrial (nonmetallic) minerals remain the often unsung workhorse of mineral commodities and specialist raw materials that frankly keep the world’s manufacturing industries ticking over, and everyday products we use in sound availability. They are also very much present among the so-called “critical minerals” necessary to advance cutting-edge developments in growing high-tech markets such as in energy transition: for example, lithium, rare earths, graphite and fluorspar. Indeed, in the United States during 2024, industrial minerals again accounted for the majority share of total sourcing, and, yes, geopolitics. The last few years have witnessed a series of geopolitical issues that have impacted and continue to impact international trade in industrial minerals. Above all, it has been the threat and implementation of recent trade tariffs between countries that have been most damaging in creating a potential trade war. mine production by value at $72.1 billion, or 54 percent, followed by metals, 25 percent, and coal, 21 percent, according to the latest data from the U.S. Geological Survey (USGS). But right now, “industry resilience” seems to be the rallying call, with industrial mineral producers and traders facing straitened times from market slowdowns; environmental regulations; decarbonization and other sustainability issues; pressure to diversify; and near-shore mineral sourcing, and, yes, geopolitics. The last few years have witnessed a series of geopolitical issues that have impacted and continue to impact international trade in industrial minerals. Above all, it has been the threat and implementation of recent trade tariffs between countries that have been most damaging in creating a potential trade war.

Jul 1, 2025

By V. T. McLemore

"Production of industrial minerals remains important to the rural economy of New Mexico. In 2014, 226 active mines and mills were registered in New Mexico and included four coal, eight potash, 11 metal, 33 industrial mineral and 170 aggregate and stone operations. New Mexico leads U.S. domestic production of potash, perlite, zeolite and travertine. Other production includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica and decorative stone. New Mexico also has the potential for additional production of industrial minerals. One company is exploring for garnet. Cretaceous black sandstones in the San Juan Basin have drawn interest for titanium, rare earth elements (REEs), niobium and zircon, and other REE deposits are being explored. REE-thoriumuranium veins have been found in the Gallinas, Capitan and Cornudas Mountains and Laughlin Peak-Chico Hills. Exploration for beryllium has occurred in the Ojo Caliente No. 2, Cuchillo Negro and Victorio mining districts. Companies also are examining high-calcium limestone and high-magnesium dolomite for potential development, while aggregate continues to be important in urban areas and along highways. IntroductionIndustrial minerals and rocks are literally the building blocks of our way of life. They are an exceptionally diverse and vital group of raw materials that underpin almost all aspects of human activity, infrastructure and standard of living. Industrial minerals and rocks are used in the manufacture of many products, from ceramics to plastics to refractories to paper. Although industrial minerals permeate nearly every aspect of daily life, their presence and their roles are typically invisible. A widely used definition of industrial minerals and rocks is “any rock, mineral, or other naturally occurring substance of economic value, exclusive of metal ores, mineral fuels, and gemstones: one of the nonmetallics” (Bates, 1975). This definition includes the important construction materials sector as well as specialized industrial minerals, but complex interactions between consumer industries produce a number of apparent anomalies to this definition. Some metals are included as industrial minerals because their use is industrial rather than as a metal. Sulfur is now predominantly extracted as a byproduct of cleaning natural gas, one of the world’s major energy fuels.Production of industrial minerals has been and remains important to the rural economy of New Mexico. Industrial minerals constitute nearly 41 percent of the more than $3.1 billion generated by mineral production in New Mexico in 2014 (Table 1). In 2014, 226 active mines and mills were registered in New Mexico and included four coal, eight potash, 11 metal, 33 industrial mineral and 170 aggregate and stone operations (New Mexico Mining and Minerals Division, 2015a). New Mexico leads U.S. domestic production in potash, perlite, zeolite and travertine. Other industrial minerals production from New Mexico includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica and decorative stone. Additional production statistics can be found in Harben et al. (2008). Major industrial mineral districts are shown in Fig. 1."

Jan 6, 2017