Search Documents

By Neil D. Policow

Dewatering of the fine clean coal fraction, - 28 mesh (595 microns) represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the Screen Bowl Centrifuge has offered an economical alternative to filtration/thermal dryer combinations. The performance of Screen Bowl Centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Actual test comparisons with alternative methods show the Screen Bowl Centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1982

By Jackson M. Langton

INTRODUCTION The Morenci-Metcalf district is located on the southern slope of the white Mountains in Greenlee County, Arizona. Both porphyry copper deposits are four to six miles northwest of Clifton, the county seat, and the new Metcalf mine is situated approximately one mile northeast of the Morenci open pit (Figure 1). Chase Creek, a south-flowing tributary of the San Francisco River, dissects the district and separates the two ore bodies. More than 1,200 exploration and development drill holes have been completed in the district and the Morenci-Metcalf ore bodies have been delineated on a 400-foot grid. Recently initiated drilling programs have revealed new data about deeper protore and associated hypogene alteration. This information, correlated with surface mapping and petrographic studies, was utilized to propose a plausible geochronologic sequence for this region. The reasoning behind this study has been helpful in locating new ore beneath leached capping indicative of only protore mineralization. The scope of this paper is to establish a practical solution to a highly theoretical problem of ore genesis and to familiarize the reader with stratigraphic, structural, and mineralogic events responsible for localizing ore in this district. Continued research will possibly alter the proposed time span and relative displacements, but it is doubtful that the order of events will vary significantly. Geochronologic conclusions are therefore presented as general hypotheses and additional geologic mapping,

Jan 1, 1972

By Paul H. Johnson

A field investigation was undertaken to study some of the. chemical and hydrological aspects of leaching an impermeable copper sulfide waste dump. Samples, obtained by means of a Becker pneumatic drill from Kennecott's Chino "J" dump, near Silver City, New Mexico, were analyzed for their moisture and soluble-salt content, Fe +2 , Fe +3, Cu +2 , and H in their interstitial solutions and non-water - soluble Fe, Cu, and S in their rinsed residues. Conclusions were drawn from these data concerning the overall chemistry of impermeable-dump leaching and the hydrological characteristics of the dump.

Jan 1, 1970

By M. A. Girts

Wetlands can be constructed inexpensively on mined lands to treat small flows of acid mine water. Metals are removed from the water by the wetland vegetation and indigenous bacteria. Full-scale field tests initiated at over 20 mine sites during 1984 and 1985 indicate that water quality can be upgraded to meet discharge standards with relatively minor maintenance requirements. Iron concentrations of 25-85 mg/L in the influent water fall to less than 2 mg/L during flow through a small wetland. Manganese can also be removed, though somewhat less efficiently. At the discharge, pH is easily raised to 6 by flow over limestone.

Jan 1, 1986

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country's largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984

By Xin Wang, He Shao, Wenpu Li, Yiyi Zheng, Xi Chen, Yurong Gao

This study utilized experimental and numerical simulation methods to investigate and analyze the atomization characteristics of three internal air–water mixed atomizers under different operating conditions. By comparing the research results, the effective dust control working parameters for the application of the selected atomizer in the engineering field were determined. Firstly, the atomization characteristics of the three atomizers were studied using a customized experimental system. The results indicated that nozzle 2 had a wide atomization range, a small atomization distance, and small droplet size; nozzle 3 had a narrow atomization range, large droplet size, and fast atomization speed; and nozzle 1 not only had a large atomization range but also could produce droplets of dry mist size with fast atomization speed, meeting the dust reduction requirements of the Majiliang Coal Preparation Plant. Secondly, Fluent software was used to simulate the atomization process and particle size distribution of the three internal mixed atomizers, determining the working conditions of the atomizers, the required number of atomizers, and the application angle of the atomizers in the internal mixed dust removal system. Finally, the atomized dust control system was applied on-site, achieving a total dust removal efficiency of 90.72% and a respirable dust removal efficiency of 89.75%.

Mar 9, 2024

By Samuel S. Adams

The Permian Salado Formation of west Texas and southeastern New Mexico is composed of halite and subordinate amounts of anhydrite, clay and potassium and magnesium-bearing evaporite minerals. Aspects of the geochemistry of the Salado Formation have been investigated through studies of the stratigraphy, mineral assemblages, textures and minor element content of the salts. These studies provide information on the origin of the evaporites when combined with data on equilibria in saturated salt solutions. The principal potash ore zone in the district is composed essentially of halite (NaC1) and sylvite (KC1). Data on the color, bromide content, and proportions of halite and sylvite suggest that this simple assemblage is the product of a series of replacements rather than primary precipitation. The bromide content of the salts also indicates that the brine which precipitated the Salado Formation was derived from the dissolution of older evaporites rather than the simple evaporation of sea water.

Jan 1, 1966

By Yao Yevenyo Ziggah, Victor Amoako Temeng, Solomon Evans Kweku Koomson

Tyre hours/life deficit is a major operational challenge facing the mining industry which adversely affects materials production and costs. An accurate forecast of the tyre life is key in addressing this menace. This study for the first time employed the hybrid intelligent technique by utilising three metaheuristic optimisation algorithms, including particle swarm optimisation (PSO), genetic algorithm (GA), and whale optimisation algorithm (WOA), as trainers for the parametric weights and biases to optimise multilayer perceptron neural network (MLPNN) for enhancing prediction of on-site dump truck tyre life in the mine. Four hybrid models known as PSO-MLPNN, WOA-MLPNN, GA-MLPNN, and BP-MLPNN were developed using a total of 157 tyre dataset records obtained from a surface mine in Ghana. In assessing the prediction performances for the models developed, five statistical performance metrics of variance accounted for (VAF), Nash–Sutcliffe efficiency index (NASH), coefficient of determination (r2), mean absolute percentage error (MAPE), and correlation coefficient (r) were utilised. Moreover, ranking, uncertainty analysis and Bayesian information criterion (BIC) techniques were utilised to establish the most effective hybrid model, whereas sensitivity analysis was conducted on the input parameters. Results achieved showed that PSO-MLPNN was the best for prediction because it had the least MAPE value of 1.196% and relatively high values of VAF (99.642%), NASH (0.996), r2 (0.996), and r (0.998). Besides, PSO-MLPNN had the best selection criteria values of 6, 7.1725, and 444.834 for the ranking, uncertainty analysis and BIC respectively. Hence, PSO-MLPNN is recommended for the prediction of on-site dump truck tyre life for the studied mine.

Mar 11, 2024

By Donna L. Boreck

In an effort to increase recovery in thick and closely spaced coal seams, the Bureau of Hines, U.S. Department of the Interior, is studying the feasibility of introducing three mining methods-high-face longwall, multi-slice longwall, and longwall caving-in western coal operations. Geology plays a significant role in determining the success of such methods. Some of the factors that will affect development are as follows: (1) thickness and three-dimensional configuration of the seam, (2) cleats, joints, and fractures in the coal and roof rock, (3) roof composition and variability, and (4) coal quality and changes in quality within the seam. Through geologic mapping, the presence of many of these factors is predictable prior to development.

Jan 1, 1987

By P. W. Conrad, C. Todd, N. A. Degerstrom, N. West, R. Kramer

"Surface subsidence caused by underground room-and-pillar mining operations and by solution mining operations have been studied separately but never in combination. In 2008, FMC Minerals began using solution mining at its Westvaco Mine as a secondary extraction method in an area that had been previously mined using the room-and-pillar mining method. Mining regulations require that subsidence associated with underground mining activities be monitored and measured annually. Using Salt_Subsid, a subsidence software package from the Solution Mining Research Institute, and ArcGIS, Esri's mapping platform, researchers at Montana Tech were able to develop a relationship between measured surface mine subsidence and solution mining that can be used at the Westvaco Mine to estimate the production of trona from solution mining operations. Project backgroundFMC Minerals has increased the production of trona from its Westvaco Mine near Green River, WY, using solution mining as a secondary extraction method in an area previously mined using the room-and-pillar method. The area of interest was mined until 2001 with the use of a borer miner at a depth of approximately 488 m (1,600 ft). Currently, FMC determines the amount of trona produced using its solution mining operations by measuring the dissolved solids pumped from the mine. This approach, however, does not account for the location from which the trona was removed.The location from which the trona is removed and the size of the cavern created by the solution mining operations are important to FMC’s mine planning. FMC believed that with proper investigation of the subsidence at the Westvaco test site, a correlation might be found between surface subsidence measurements and the amount and location of trona production from the solution mining activities. The primary goal of this project, conducted by Montana Tech, was to find relationships between the measured subsidence and the solution mining activities. The project attempted to develop an equation that could be used to predict solution trona production based on measured subsidence. The project attempted to model the relationship between the measured surface subsidence and solution mining production using Salt_Subsid, an existing subsidence software package from the Solution Mining Research Institute (SMRI, Clarks Summit, PA) to estimate the location, size and shape of the solution mining cavern. This study would determine the program’s usefulness for locating and developing the cavern created by secondary solution mining activities. The subsidence and production data sets used in this study were collected over a seven-year period from 2008 through 2014."

Jan 4, 2018

By Tácio Ferreira, Liz Diaz

Capstone Copper’s Pinto Valley Mine faced challenges in recovering rock and ore on final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall stability. The operation had been using the same drill-and-blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at 345 kt/a (380,000 stpy) generated from an average of 60 final wall blasts performed annually. The engineering team from Capstone and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. This article presents how data were collected and design standards reviewed, and the opportunities that were found to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71 percent on the mine’s highwalls.

Aug 1, 2025

By John J. Dwyer

As one begins to contemplate the organization of a talk with the title "Iron Ore - The Permanent State of Evolution," the main divisions appear to be the past, the present, and the future. But distaste for repetition of the present production achievements, which scarcely need additional description on this occasion, soon leads one to the conclusion that a more appropriate division of the subject is simply the past and the future . . . with emphasis on the future. We are working in the present, but it can only be understood by what has taken place in the years and decades gone by, and/or under what terms we will have to face the future. Evolution is more often thought of as a steady change - but steady change is really the product of revolutions, sometimes making headlines but often unnoticed at the time. With hindsight, we recognize the great importance of the emergence of the Bessemer converter and the open hearth and the vast influence that both have had on steel making and the changing ore demand. In this country we also see schooners opening the era for lake transportation of iron ore from Michigan to Take Erie. Later, steamships haul the ore from the Mesabi Range to the steel centers of the country. In order to take full advantage of the inland seaway, there had to be revolutions in ship design, loading and unloading facilities and channel and lock development. Full scale utilization of the resources of the Mesabi Range, itself, required parallel upheavals such as the development of new production equipment, and substitution of modern forms of energy for horsepower, and, yes, manpower, as well.

Jan 1, 1968

By Alireza Kamrani, Yashar Pourrahimian, Hooman Askari-Nasab

In-pit crushing and conveying (IPCC) is an option to decrease the enormous operating costs that a truck shovel can introduce in an open-pit mine. Finding the best locations for the IPCC over the mine life will impose a new set of requirements for the mine planning. Through a two-step mathematical programming model alongside the road network, this method finds the optimal in-pit crusher locations and relocation times first and then optimizes the long-term mine schedule. The model is verified by a real mine. The results show that the truck travel time could be reduced by 500% and the discounted cash flow increased by 8% with an optimized schedule considering the crusher placement.

Jun 25, 2023

By James C. Barker

Alaska?s known mineral endowment includes some of the largest and highest grade deposits of various metals, including gold, copper and zinc. Recently, Alaska has also been active in the worldwide search for sources of rare earth elements (REE) to replace exports now being limitedby China. Driven by limited supply of the rare earths, combined with their increasing use in new ?green? energy, lighting, transportation, and many other technological applications, the rare earth metals neodymium, europium and, in particular, the heavy rare earth elements terbium, dysprosium and yttrium are forecast to soon be in critical short supply (U.S. Department of Energy, 2010). The REE, accompanied by other high field strength metals (such as Nb, Zr, Ti, Th, W), are associated with alkaline complexes of the Hogatza Belt in northwest Alaska; peraluminous tin-granites of the Ruby batholith in central Alaska and the Porcupine plateau in the northeast; and peralkaline intrusive complexes in the southwest Alaska Range west of Anchorage, and on Prince of Wales Island in southeastern Alaska. Limited evidence suggests that the heavy REE are associated with deposits that became more highly evolved by late hydrothermal processes.

Jan 1, 2012

By J. Sanko

When faced with the task of designing a process control system the control engineer must consider the following: 1. The type of process to be controlled and the manner in which the process must be controlled (the algorithm). 2. The type of equipment to be used to implement the control system. 3. A means of describing the control system for use in the following areas: a. Project engineering. b. Procurement of the control system equipment. c. Plant startup. d. Operator training and reference.

Jan 1, 1981

By Arthur R. MacPherson

Este capítulo revisa las etapas que deben seguirse desde el momento de considerar la molienda autógena en el desarrollo de un nuevo depósito de mineral o en la expansión de una planta existente, hasta la compra de un molino autógeno. En este caso el término autógeno incluye: semi-autógeno, molinos de pebbles secundarios y molino de bolos (trozos), así como los sistemas de molienda autógena total. También se han incluido las alternativas por vía húmeda y seca. Antes de programar el ensayo debe decidirse cuantas muestras brutas son requeridas para calcular propiamente las posibilidades de molienda autógena del depósito. También ha de tomarse la decisión, de como y donde deben tomarse las muestras, por ejemplo: planta piloto situada en el sitio de localización de la planta o en otro lugar establecido; molienda en húmedo y/o en seco....etc. En el mismo programa del ensayo se obtendrán ciertos datos fundamentales. Los ensayos deberán incluir un trabajo suficiente. para determinar cuál de las moliendas, totalmente autógena o semi-autógena, debe utilizarse; y qué tipo produce la máxima eficacia en la potencia consumida. También, los otros datos pertinentes deben ser recolectados, como por ejemplo: potencias, tonelajes, alimentación, carga, tamaño del producto, carga circulante, etc. Si es necesaria una molienda secundaria para obtener el tamano final, la decisión de qué molienda debe emplearse (molino de pebbles o molino de bolas) puede requerirse un ensayo de trabajo adicional. Finalmente, la concentración del mineral puede jugar un papel importante en la selección del circuito y debería ser una parte del ensayo final una vez que se ha establecido la molienda. Para determinar qué tipo de molinos pueden satisfacer los requerimientos establecidos por la planta piloto, debe tomarse una escala para ciertos datos como: potencia del molino, consumo de acero, simple o doble etapa de molienda, tipo de molino secundario. Para asegurar un posterior entendimiento del depósito de mineral y sus características de molienda, deberán efectuarse algunos trabajos adicionales a pequena escala utilizando pequeñas muestras y molinos para producir unos datos comparables de molienda. También, algunos ensayos tales como medio de molienda óptimo, e índice de trabajo, deberán ser completados.

Jan 1, 1982

By F. Calizaya

This study summarizes the results of various numerical and laboratory experiments per-formed to study the effect of airflow recirculation on gas concentration. The numerical exercises were carried out on a simulated mine ventilation net-work. The laboratory experiments were conducted at the Mackay School of Mines' airflow monitoring system in Reno, Nevada. In both cases, the airflow was recirculated through the system by means of a main fan and a set of booster fans. The booster fans were positioned to produce two types of recirculation: In line and Cross-cut. For each type, various recirculation conditions were generated by changing the booster fan pressure. During each test, the gas emission rate at the simulated working face was kept constant. The study illustrates the conditions under which controlled airflow recirculation may be used to solve a district ventilation problem.

Jan 1, 1991

By William H. Pomroy

This report describes research leading to the design, prototype fabrication, and successful in-mine proof-of-concept testing of two improved stench fire warning systems for underground noncoal mines. The stench system, widely used in underground noncoal mines to warn of fire or other emergency suffers several serious shortcomings, including the toxicity of the odorant leading to debility in miners; reactivity of the odorant with iron oxide, resulting in unreliable warning because the odor may fade when transported long distances in steel pipe; lack of control over the rate at which agent is released into the air-stream, resulting in some work areas receiving unbearably high stench concentrations and other areas being missed altogether; lack of visual indication of system status, valve positions, or proper system operation; and excessively long stench transit times. In 1979, the Bureau of Mines, U.S. Department of the Interior, began research to upgrade the stench warning system. Two systems were subsequently developed which offer significant advantages over current systems.

Jan 1, 1984

By John Rudolf

Metropolitan Washington Airport Authority is currently undertaking the first Phase of Metro?s Extension to Northern Virginia. A wide range of tunnel options was considered for the Tysons Corner segment that involves about 20,000 feet of track and four stations. After consideration of many options that involved EPBM single track tunnels, NATM tunnels and large bore tunnel concepts for the entire Tysons alignment, the design now being progressed into construction involves two 520 meter (1,700 feet) long soft ground NATM tunnels with several hundred feet of cut-and-cover construction. The paper discusses the process that led to selection of the short NATM tunnels as the most feasible of the options considered for Tysons.

Jan 1, 2008

By A. L. Mula

Pasaremos revista brevemente a 10s fundamentos de 10s ciclones, considerando un ciclón típico. Los datos gráficos disponibles en la literatura han sido convertidos en ecuaciones matemáticas por conveniencia. Se suministran los procedirnientos preliminares para seleccionar y diseñar tanto los ciclones como las bombas, y se facilita con algún detalle un ejernplo de cálculo para un hipotético circuito de molienda. En general, debe consultarse a 1os proveedores de ciclones y bombas para determinar un disefio definitivo. Algunos suministradores de ciclones emplean normalmente computadores digitales para el diseño definitivo con objeto de asegurar una gran precision.

Jan 1, 1982