Search Documents

By L. P. Johnson

Longwall mining has gained acceptance as a safe method of maintaining coal production where conventional systems were unsuccessful or uneconomic due to bad roof conditions (Kuti8). One of the major problems confronting American operators involves the correct choice of equipment which should be selected to suit the local mining and geologic conditions for optimum productivity. To achieve this, factors such as rock strengths, local geology, panel geometry, and panel orientation must be examined to optimize production and minimize down time due to ground control problems. Little quantitative information is available in the literature regarding the effects of geologic conditions on American longwall operations, and past implementations of longwall systems appear to have been based largely on experience. When mining engineers are able to assess the geologic conditions both quantitatively and qualitatively, they can more fully optimize equipment selection and panel design.

Jan 1, 1977

By Gary E. Slagel

The federal Office of Surface Mining (OSW) has undertaken an effort to revise many of their permanent program regulations. Numerous procedures for compliance are being rewritten to allow for greater flexibility while meeting the requirements of the Surface Mining Control and Reclamation Act. This study investigates, for certain select provisions, the cost differential between complying with the original OSM standards and the more flexible, state-specific standards being allowed in many of the revised regulations. Estimated cost savings that could be realized under a few of the revised regulations are substantial and should provide a basis for seeking revisions to the state regulatory programs.

Jan 1, 1982

By Scott O’Brien, Richard Williams, Camilo I. Mejias, Elias Godoy, Javier Sierra

High-rate thickeners play a critical role in tailings management by enhancing water recovery and increasing solids concentration. However, these units face operational instability due to fluctuations in feed solids, flow rate, and flocculant response typically managed in manual mode with delayed corrective actions. This work presents an adaptive automatic control algorithm designed for dynamic thickening environments. The algorithm integrates real-time measurements of feed density, rake torque, bed level, and turbidity (overflow), optimizing the underflow slurry density while minimizing suspended solids in the overflow. The proposed control strategy is modular, simple, scalable, and applicable to both existing and new thickening systems, offering a robust alternative to manual operation in increasingly demanding metallurgical environments.

Feb 22, 2026

By D. Castillo

The effectiveness of a flotation column is due principally to the addition of wash water to the froth phase. The wash water flow rate can be significant, especially so for systems yielding a high weight recovery of fine solids, e.g. zinc sulfide flotation. Therefore, it is critical to recognize and assess the impact of the water addition upon upstream separation stages. This paper examines column flotation circuit configurations using data from a portable 2 t/day pilot plant. The objective is to provide an improved basis for column design, either as a retrofit or as part of a new circuit.

Jan 1, 1990

By E. E. Maurer

Kerr-McGee has operated the Ambrosia Lake uranium mill since startup in 1958. Tonnage milled per day has varied from 3500-7000 tons. The mill capacity is currently rated at 7000 tons per day. The process consists of two parallel circuits following crushing and sampling, \\lhich include open circuit rod mill grinding, sulfuric acid leach, cyclone classification, and counter-current washing circuits of sand classifiers and slime thickeners. Pregnant solution is clarified and polished by precoat pressure leaf filters prior to amine solvent extraction. Yellowcake is precipitated from the pregnant strip solution with ammonia, filtered and dried.

Jan 1, 1972

By R. L. Grayson, F. Giana, R. Aspinwall

Small-mine and contractor Fatal Incidence Rates have been a problem for over 20 years in the coal industry, and the rates persist as unacceptably high. This paper briefly retraces historical information and data on the continuing problem and recounts the many unsuccessful efforts and initiatives to address the problems effectively. Next the results of a review of international literature on addressing the problems are presented. After focusing on a method to pinpoint the trouble spots more specifically through a nested data analysis, suggestions are provided on how the problem may potentially be addressed more systematically and effectively in the U.S.

Jan 1, 2006

By Carl G. Hogberg

To the casual observer there is probably no simpler appearing operation in the mineral industry than a limestone quarry. It might seem that the entire operation - from the drilling, blasting, and loading of the stone, its transport to a mill for crushing, washing and sizing, to loading into boats, railroad cars, or trucks for delivery to customers - can be comprehended at a glance. But no first impression could be more misleading. It is one of the purposes of this presentation to sketch the broad outlines of the extensive limestone industry in the United States which, measured in terms of volume of production since the end of World War II, has grown almost 300 per cent to a national level in 1957 of 384 million net tons.1 Another objective will be to discuss in more detail this industry in the State of Michigan. For this latter purpose, the Michigan Limestone Division plants at Calcite and at Cedarville will be used as examples. These descriptions will, we believe, show that the limestone business has complexities to match its size.

Jan 1, 1962

By M. K. Rizkalla

This paper discusses the time-dependent behaviour of rock when it involves the presence of several layers of rock strata in the vicinity of mine openings, mining in sequences and the placement of backfill. The paper describes numerical techniques which proved useful when such situations are encountered in practice. The model is elastoviscoplastic. At given time stations, short term loading or changes can be made to the creep behavior of the rock. The modelling technique is first described and is followed by simulations of stresses and displacements in a potash mine with the primary objective to demonstrate the effect of such aspects as mining and fill sequences in 3-D. This involves cutting finite elements representing the strip of the mining face and simultaneously filling those elements representing the newly placed fill. The stiffness of the fill varies with the degree of compaction at each point. In this way, the effect of the time of fill placement, the gap between the top of the fill and the back as well as the degree of compaction are simulated. The second example is a 2-D problem simulating the long term effect of backfill, as a material compacting with time, on the settlement of the layers above it as well as the closure of the room.

Jan 1, 1996

By Z. Mullard

The introduction of social media platforms has ushered in a new era of interaction and information exchange, which impact business-to-society relationships. Mining companies are closely watching these platforms, as the industry takes a cautious approach to control flows of information. This paper explores the risks, challenges and opportunities of using social media, based on a qualitative mixed methods investigation with stakeholders from the Canadian mining industry. Generational and language barriers, misunderstanding and limited motivation from regulators make implementing social media platforms challenging and risky at an organizational level. The benefits of social media include being able to mobilize communities and share information in real time. Despite the challenges, the study found that 62% of mining stakeholders are incorporating social media tools, mostly in an ad hoc manner. Flexible strategies for transparent communication and public engagement are creating new opportunities for information exchange.

Jan 1, 2011

By R. L. Summers

The tremendous engineering advances occurring during this past century are very evident within the boundaries of the Anthracite Section of AIME. The Steelton plant of Bethlehem Steel Corporation, located along the Susquehanna River just east of the Commonwealth's capital at Harrisburg, for more than 105 years has experienced a most dynamic life which has paralleled America's industrial growth. (Figure 1) In June 1865, just after the Civil War, a group of men met to organize the Pennsylvania Steel Company. The war had brought into sharp focus the vital importance of the railroads to the country's expansion. Until that time wrought iron rails were used, and the replacing of track after only several months wear had become an almost unbearable cost. The spirit of free, competitive enterprise and the prospects of a lucrative market compelled these men to form that first Pennsylvania Steel Company and to develop better rail products. They issued the following statement: "...our desire to free ourselves from dependence upon a foreign market (has) led to the organization of the Pennsylvania Steel Company, and the parties who have connected themselves with it are determined to produce upon American soil all the principal manufactures of steel that are now, at such a serious cost for freight, commission, insurance, exchange, duty, etc., and often, with so much delay and uncertainty, imported from abroad. (We) are preparing to establish near the consumer, works at which articles of accustomed pattern will be promptly produced, and from the

Jan 1, 1971

By W. L. Freyberger

In many papers concerned with fundamentals of the froth flotation process, authors have considered the contents of a flotation cell to be comprised of two immiscible phases, the froth and the pulp. I (Of course, each of these phases is in turn made up of several solid phases plus air and water.) This generalized concept of the flotation system can be extended by considering the cell contents to include two phases: an extracting phase, the air bubbles plus the collector, which removes a selected mineral component from the second phase, the ore pulp. Thus, there is an analogy between a flotation system on the one hand, and chemical extracting systems, such a solvent extraction system or a leaching system, on the other hand. Such extracting systems may be operated in cocurrent or countercurrent fashion. This paper includes first a brief discussion on the general nature of cocurrent and countercurrent operation as applied to froth flotation, and then presents the experimental results of flotation of a specular hematite ore by each method, using a tall oil fatty acid as collector. Cocurrent Flotation A conventional flotation circuit involving roughing, scavenging, and cleaning flotation is illustrated schematically in Figure 1. In such a circuit the col¬lector, or extractant, and new feed ore enter together at the head of the rougher circuit, and flow cocurrently to the scavenger circuit where more collector is added. According to this practice, sufficient collector is added to the head of the rougher (and scavenger) so that the final tailings are of low enough grade to be discarded. Since the flow of collector and ore is cocurrent, the process consists of single stage contact between the extracting phase and the ore pulp. If the scavenger concentrate is recycled to the head of rougher, the overall circuit has some of the characteristics of countercurrent flow. In such a case part of the extractant (collector) is added at the discharge end of the circuit, and may

Jan 1, 1971

Due to the ongoing restructuring of the mining industry in central Europe with a continuous decline of the number of large underground mines and collieries, and a simultaneous decline of staff numbers in the remaining mines, the established mine rescue schemes are endangered to collapse. With the end of the mine rehabilitation at Wismut Uranium in 2014, the last remaining major mine rescue teams in Saxony, providing basic mine rescue services for all other mines in the region, will disappear. This will leave a large number of small mines and other underground operations without capable mine rescue support. Since none of these companies is able to set up a complete mines rescue unit on its own, new ways have to be found. Among others, a central mine rescue team for central Germany as well as the assistance by special trained professional fire fighters or mine rescue teams from abroad are discussed. Problems like location of the central rescue team, financing, communication and transport have to be solved. This paper provides an overview over the complexity of the problem as an example for other mining regions worldwide and will discuss national and cross-national strategies.

Feb 23, 2014

By T. J. DeMull

The business of heap leaching requires accurate forecasting of metal production from the heaps. Business forecasts typically follow a format that project periodic (monthly, quarterly, or annual) product shipments based on anticipated operating results, e. g., tons of ore placed, grade of ore, and rate of leach extraction. Since revenue and cash flow are dependent on the metal production stream, forecasts of metal production are very important for project evaluation and business planning purposes. Nevertheless, production forecasts, particularly for new heap leach projects, have been prone to errors. The present paper identifies some of the pitfalls that would be encountered in preparing production forecasts for new heap leach operations and provides a checklist of considerations to assist in preparing a forecast. Also, the paper presents a case study of copper production forecasting used for the Sanchez Project, a heap leach operation located near Safford, Arizona, that is presently under development by AZCO Mining, Inc.

Jan 1, 1995

By Cary Hirner, Sarah Lothman, Chris Mueller, Savita Schlesinger, Mike Hanna, Ian Fitz-James

Loudoun Water is currently implementing a quarry to reservoir conversion that will improve water supply reliability in periods of drought and flexibility in water supply operations when turbidity in its Potomac River supplies are high. The Milestone Reservoir Project consists of an inter-tie to the existing Potomac River Pipeline; new pipeline and tunnel; and a pumped intake and outlet works. Planned construction involves significant risks due to underground conditions which includes hard, igneous rock and high groundwater at the creek crossing. In addition, the site is constrained by Goose Creek, an adjacent residence, active mining in a quarry next to the new reservoir, public use of adjacent park space, and the Washington and Old Dominion Trail. Working with these constraints will require close coordination with active mining operations and public and private property owners. Safety of personnel involved with construction also represents a concern with quarry high walls over 30 meters in height near the planned construction. In consideration of key projects risks, Loudoun Water determined that an innovative CMAR delivery approach provided the best opportunity to achieve its goals in quality, innovation, front-end cost and schedule certainty, and operational flexibility and reliability. What matters most to Loudoun Water is the value in having a builder participate in the design process where key decisions can be made based on consideration of risks, cost, schedule, quality, and operability and maintainability of the system. While a progressive design-build delivery model may have produced similar outcomes, Loudoun Water had already invested in substantial development of the design for the work, and ultimately, CMAR provided Loudoun Water the opportunity to retain the partnership with the design team while gaining valuable input from a contractor. Among the challenges with CMAR in the Commonwealth of Virginia is a substantial limitation on self-performance corresponding to 10 percent of the construction value of the work. A significant industry outreach program was initiated by Loudoun Water to encourage participation with incentives in contract terms that allowed for the CMAR Contractor to make a reasonable profit. This paper reviews the CMAR procurement process and discusses contract incentives that were adopted to promote the work within the constraints of contract law in Virginia.

Jun 13, 2021

By Tim O’Neil

The US Bureau of Mines and the Santa Cruz Joint Venture (SCJV) are working on a production-scale, in situ copper recovery project in Arizona. The research is being conducted at the Santa Cruz site, located 11.2 km (7 miles) west of Casa Grande, AZ (Fig. 1). Santa Cruz is a 1.36-Gt (1.5 billion st) porphyry deposit averaging 0.6% Cu, of which 65% is oxidized, concealed beneath post-mineral alluvium at depths of 365-914 m (1500-3000 ft). The Bureau and the SCJV will evaluate in situ mining as a method for extracting copper from this previously unmined deposit. Research objectives of the Santa Cruz project are: - to demonstrate that an in situ research test can be operated in an environmentally acceptable manner ; and * to operate an in situ well pattern long enough to develop information on copper recovery and economic feasibility data. In situ mining of copper from undisturbed deposits has not been attempted commercially. There are several potential advantages with in situ mining: less exposure of miners to hazards, lower pital costs for the mine and plant and lower operating costs. In addition, there are no pits, dumps or tailings, which means less environmental impact.

Jan 1, 1991

By M. K. Buder

Over the years, electric utilities have been faced with declining steam-coal quality, rising coal prices, and increasingly rigid and costly environmental standards. As a result, many utilities are beginning to show an interest in coal cleaning to upgrade coal by improving its heating value and reducing its sulfur content. Among the primary questions that must be answered for these electric utilities is whether the cost of coal cleaning can be offset by the potential cost savings in coal transportation and utilization in power generation. In search of at least a preliminary answer to this question, the Electric Power Research Institute (EPRI) engaged Bechtel to perform a case-by-case economic study to examine the cost effects of using cleaned versus raw coal to fuel new electric power plants. The results of two of the seven cases studied which involved western coals - one from Montana and another from Utah - are reported in this paper. Coal cleaning appeared to be a cost effective option for the Utah coal, but only marginally economical for the Montana coal. These cost results are expected to change to favor coal cleaning to a greater extent with the application of the final revised New Source Performance Standards regulating SO2 emissions just issued by the EPA. The study was based on the regulation originally proposed by the EPA under the 1977 Clean Air Act Amendments.

Jan 1, 1979

By W. Miola

The MSHA prescribed method for the determination of quartz in airborne respirable dust samples from underground coal mines is the P-7 method, a combination of low temperature radio-frequency ashing (LTA) and infrared analysis (lR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive Infrared (IR), Fourier-transform Infrared (FTIR), and X-Ray Diffraction (XRD) methods are most commonly used for quartz analysis in powders. Several aspects of the experimental procedures such as the analysis sample preparation from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist, and data interpretation affect differently the results from each of the methods. Significant differences in analysis results from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All these studies point to the need for reliable quartz analysis methods. In a recent research, a procedure for preparing bulk coal and host rock samples for quantitative quartz analysis was developed. Further the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle size distribution, matrix, and calibration on analysis results. In this paper, several issues with the measurement of quartz in the samples of coal, host rock, and airborne respirable dust from mines are outlined and quantified.

Jan 1, 1994

By Steven Hoerger

Mixed integer linear programming (MILP) production scheduling models can be used to evaluate if tonnage improvement projects will deliver value over all time periods and whether new bottlenecks will be created. These MILP models can evaluate the interconnected effects of mine and process capacities, mining locations, cutoff grades, stockpiles, and orebody grade/tonnage distributions. A case study compares potential value creation from a mine capacity increase, a mill capacity increase, or a simultaneous increase in all capacities. For perspective, project valuations for capacity increases are compared against valuations for cost reduction projects, mine planning improvements such as phase design, dynamic cutoff grades and stockpiling, and the impact of geostatistics improvements in the areas of block model accuracy and ore control selectivity.

Feb 1, 2024

By Todd A. Duex

The Richmond Hill Mine has recently completed a reclamation plan to mitigate Acid Rock Drainage (ARD) which was identified at the toe of the former waste rock pile in 1992. Reclamation activities began in 1994 with the removal of ARD material from the waste rock pile and placement of this material in the former pit. This material was then isolated from the near surface environment by a low permeability capping system designed to minimize water and oxygen flow into the material. The capping system consists of, from bottom to top, six inches of limestone, 18 inches of low permeability clay liner, 4 and one-half feet of thermal barrier/drain layer, and six inches of topsoil. This capping system was completed in 1995. An extensive program is in place to monitor the effectiveness of the reclamation plan, and includes measurements on moisture content movement, temperature, oxygen content, and groundwater impacts. Monitoring has been ongoing since the completion of reclamation. This monitoring plan is demonstrating the success in isolating the material from the near surface environment and minimizing the impacts to the surrounding environment.

Jan 1, 2000

By William D. Cassity, Batric Pesic

Introduction Gold mining on an industrial scale is becoming increasingly dependent on low-grade refractory sulfide ores that contain large amounts of pyrite (FeS2) and arsenopyrite (FeAsS). Gold is usually present as sub-microscopic particles dispersed evenly throughout the sulfide matrix. Without some form of preoxidation, efficient recovery of this finely disseminated gold through cyanide leaching is hampered because the surface of the sulfide particle becomes passivated and impervious to penetration of the cyanide. Traditional methods for recovery of refractory gold from arsenopyrite ores include roasting and autoclave leaching. A modem alternative method is to preoxidize the mineral using the bacterium Thiobacillus ferrooxidans prior to attempting to re- cover the gold through cyanidation. The bioleaching of arsenopyrite ores presents a problem in the mobilization of large quantities of arsenic, present both in the +5 and +3 ionic states. Dissolved arsenic species pose a dual problem: they are -1 to the bioleaching process itself through inhibition of bacterial activity, and they also pose an environmental threat. The arsenate anion (AsO2) has been shown to be more toxic to living organisms, including Thiobacillus ferrooxidans, than the arsenate anion (AsO43) (Collinet and Morin, 1989). There is some disagreement as to the fate of arsenite in bioleaching solution. Mandl, Matulova, and Docekalova (1992) reported that dissolved arsenite concentration was constant during a long-term bioleaching study of chalcopyrite using Thiobacillus ferrooxidans. Torma and Oolman (1992) report that Thiobacillus ferrooxidans has been found capable of oxidizing As3+ to As5+. The solid products of arsenopyrite/pyrite bioleaching include jarosite (MFe3(SO4)2(OH)6 where M can be K+, Na+, NH4+ or H3O+), scorodite (FeAsO4.2H2O), ferric hydroxides, and ferric hydroxysufites (Carlson et. al., 1992; Van Breemen, 1982; Lazaroff et. al., 1982). The particular species formed is a function mainly of pH. Little study has been performed on the effect of solid products on bioleaching. Pesic and Kim (1993) showed that Thiobacillus ferrooridans cells served as a nucleation sites for jarosite particles, which grew rapidly and eventually killed the cell. Most bioleaching studies are performed at low pH&apos;s (<2.0) under uncontrolled conditions. By studying bioleaching of arsenopyrite under controlled pH conditions and at higher pH&apos;s (2.0 to 3.0), the distribution of iron and arsenic between the solid and liquid phases can be controlled, and their effects studied. The objective is to develop a bioleaching process that operates at high efficiency while keeping amounts of dissolved heavy metals low. Pesic, Stohok, and Torma (1993) demonstrated the usefulness of this approach in the leaching of cobaltite (CoAsS) concentrates. Materials and Methods The focus of this study was the bioleaching of arsenopyrite ore by Thiobacillus ferrooxidans. The parameters studied included the effects of pH, and the effects of arsenate (AsO43 and arsenite (AsO2). pH studies included pH set initially but not controlled, and pH controlled continuously with NaOH or LiOH. Bioleaching results from two strains of Thiobacillus ferrooxidans with different adaptation histories were compared. Bioleaching experiments were conducted in 150 ml stirred glass reactors using a strain of Thiobacillus ferrooxidans adapted to arsenopyrite ore, supplied by the U.S. Bureau of Mines. These bioreactors were innoculated with stock cells grown on arsenopyrite ore for 14-16 days. Typical elemental breakdown for this ore was: As, 9.90%; Fe, 18.60%, Stot, 9.26%; Suifide, 7.50%; SiO2, 25.90%. Mineralogically, the ore contained both arsenopyrite and pyrite. Bioleaching efficiency was measured by withdrawing bioleach solution samples at selected intervals, filtering, and measuring the amount of dissolved cobalt, iron, and arsenic by atomic absorption spectroscopy. Because the precipitation of iron and arsenic at higher pH&apos;s would lead to unreliable results, a 100 mg tracer of cobaltite concentrate from the Blackbird mine in southern Idaho was added to solution. Dissolution of the cobaltite tracer was used to indicate bioleaching of the bulk arsenopyrite ore. Cobalt has been shown to be stable in solution even when iron and arsenic were precipitated (Pesic, Storhok, and Tonna, 1993). The pa-

Jan 1, 1995