Search Documents

By Gary E. Slagel

The federal Office of Surface Mining (OSW) has undertaken an effort to revise many of their permanent program regulations. Numerous procedures for compliance are being rewritten to allow for greater flexibility while meeting the requirements of the Surface Mining Control and Reclamation Act. This study investigates, for certain select provisions, the cost differential between complying with the original OSM standards and the more flexible, state-specific standards being allowed in many of the revised regulations. Estimated cost savings that could be realized under a few of the revised regulations are substantial and should provide a basis for seeking revisions to the state regulatory programs.

Jan 1, 1982

By W. L. Freyberger

In many papers concerned with fundamentals of the froth flotation process, authors have considered the contents of a flotation cell to be comprised of two immiscible phases, the froth and the pulp. I (Of course, each of these phases is in turn made up of several solid phases plus air and water.) This generalized concept of the flotation system can be extended by considering the cell contents to include two phases: an extracting phase, the air bubbles plus the collector, which removes a selected mineral component from the second phase, the ore pulp. Thus, there is an analogy between a flotation system on the one hand, and chemical extracting systems, such a solvent extraction system or a leaching system, on the other hand. Such extracting systems may be operated in cocurrent or countercurrent fashion. This paper includes first a brief discussion on the general nature of cocurrent and countercurrent operation as applied to froth flotation, and then presents the experimental results of flotation of a specular hematite ore by each method, using a tall oil fatty acid as collector. Cocurrent Flotation A conventional flotation circuit involving roughing, scavenging, and cleaning flotation is illustrated schematically in Figure 1. In such a circuit the col¬lector, or extractant, and new feed ore enter together at the head of the rougher circuit, and flow cocurrently to the scavenger circuit where more collector is added. According to this practice, sufficient collector is added to the head of the rougher (and scavenger) so that the final tailings are of low enough grade to be discarded. Since the flow of collector and ore is cocurrent, the process consists of single stage contact between the extracting phase and the ore pulp. If the scavenger concentrate is recycled to the head of rougher, the overall circuit has some of the characteristics of countercurrent flow. In such a case part of the extractant (collector) is added at the discharge end of the circuit, and may

Jan 1, 1971

By W. W. Simpson, S. A. N. Sheya

A procedure was developed by the U.S. Bureau of Mines for recovering gold, silver, cobalt, copper, and zinc from a massive sulfide ore by a hydro-metallurgical process. The procedure consists of (1) oxygen pressure leaching; (2) iron, arsenic, and copper removal from the leach solution by precipitation; (3) selective extraction of cobalt and zinc from solution; (4) electrodeposition of the cobalt and zinc from the strip liquor; and (5) cyanidation of the pressure leach residue to recover gold and silver. The results are discussed in terms of efficiency of metal recovery and conclusions drawn as to possible benefits and broad applications of the process.

Jan 1, 1990

By Tim O’Neil

The US Bureau of Mines and the Santa Cruz Joint Venture (SCJV) are working on a production-scale, in situ copper recovery project in Arizona. The research is being conducted at the Santa Cruz site, located 11.2 km (7 miles) west of Casa Grande, AZ (Fig. 1). Santa Cruz is a 1.36-Gt (1.5 billion st) porphyry deposit averaging 0.6% Cu, of which 65% is oxidized, concealed beneath post-mineral alluvium at depths of 365-914 m (1500-3000 ft). The Bureau and the SCJV will evaluate in situ mining as a method for extracting copper from this previously unmined deposit. Research objectives of the Santa Cruz project are: - to demonstrate that an in situ research test can be operated in an environmentally acceptable manner ; and * to operate an in situ well pattern long enough to develop information on copper recovery and economic feasibility data. In situ mining of copper from undisturbed deposits has not been attempted commercially. There are several potential advantages with in situ mining: less exposure of miners to hazards, lower pital costs for the mine and plant and lower operating costs. In addition, there are no pits, dumps or tailings, which means less environmental impact.

Jan 1, 1991

By W. Miola

The MSHA prescribed method for the determination of quartz in airborne respirable dust samples from underground coal mines is the P-7 method, a combination of low temperature radio-frequency ashing (LTA) and infrared analysis (lR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive Infrared (IR), Fourier-transform Infrared (FTIR), and X-Ray Diffraction (XRD) methods are most commonly used for quartz analysis in powders. Several aspects of the experimental procedures such as the analysis sample preparation from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist, and data interpretation affect differently the results from each of the methods. Significant differences in analysis results from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All these studies point to the need for reliable quartz analysis methods. In a recent research, a procedure for preparing bulk coal and host rock samples for quantitative quartz analysis was developed. Further the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle size distribution, matrix, and calibration on analysis results. In this paper, several issues with the measurement of quartz in the samples of coal, host rock, and airborne respirable dust from mines are outlined and quantified.

Jan 1, 1994

By T. J. DeMull

The business of heap leaching requires accurate forecasting of metal production from the heaps. Business forecasts typically follow a format that project periodic (monthly, quarterly, or annual) product shipments based on anticipated operating results, e. g., tons of ore placed, grade of ore, and rate of leach extraction. Since revenue and cash flow are dependent on the metal production stream, forecasts of metal production are very important for project evaluation and business planning purposes. Nevertheless, production forecasts, particularly for new heap leach projects, have been prone to errors. The present paper identifies some of the pitfalls that would be encountered in preparing production forecasts for new heap leach operations and provides a checklist of considerations to assist in preparing a forecast. Also, the paper presents a case study of copper production forecasting used for the Sanchez Project, a heap leach operation located near Safford, Arizona, that is presently under development by AZCO Mining, Inc.

Jan 1, 1995

By Henning E. Soderberg, Robert Brien, O&apos

Coal may be the answer to US energy problems, but it also has its drawbacks. If it is crushed, screened, dumped, or moved, the environmental engineer is faced with a dust problem. To control coal dust, at both minimum initial cost and reasonable operating cost, demands a working knowledge of dust control equipment design, as well as the coal handling operation. Here are some guidelines to reduce air volume requirements and cut overall system costs.

Jan 10, 1981

By Bo-Hyun Kim, Mark K. Larson

"Bumps remain a critical safety concern in underground coal mining, despite significant advancements in engineering controls. These events occur when relatively high stresses in a coal pillar in conjunction with low confinement exceed the pillar’s critical capacity, causing the pillar to rupture without warning. Floor failure often occurs and can be an indicator of bump risk, as it is strongly associated with brittle failure known as spalling under a lower confinement. Significant floor heave at a western U.S. coal mine has been observed where the pillar width in a three-entry gate road system was 53 m, while no significant floor heave was observed where the pillar width in another gate road system was 22 m. This phenomenon was widely reported in the region and at another mine in another western coal field it has been reported that larger pillars are always associated with floor heave. In this study, a spalling model based on the S-Shaped brittle failure criterion and associated with the anisotropic characteristics of the materials was used in FLAC3D. The observed floor heave phenomenon associated with the larger pillars was demonstrated using this modeling approach.INTRODUCTIONFloor failure in a coal mines often inhibits longwall mining operation, as large displacement of floor strata, known as floor heave, interferes with travel, access, ventilation, and equipment operation. Aggson (USBM 1978) investigated floor heave in West Virginia where underclay is relatively strong and high horizontal stress is present. It was reported that the failure mode is mainly by buckling rather than by plastic flow.This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock mass behavior in longwall coal mines in highly stressed, bump-prone ground. More specifically, this study attempts to explain through numerical models small energy releases in the form of floor heave. The authors believe that brittle rock failure is associated with both floor heave and some bump mechanisms, if not directly involved in their cause."

Jan 1, 2019

By J. C. Agarwal

A significant portion of the, coal mined by U. S. Steel is beneficiated to upgrade the quality of the resultant coke to meet blast-furnace requirements. Primarily because of degradation from modern mechanized mining methods, a considerable quantity of the coal to be beneficiated is in the 1/4-inch by 100-mesh size range. In the cleaning plants, this coal is usually cleaned on concentrating tables and then mechanically dewatered in solid-bowl centrifuges to 9 to 14 percent water. At some plants, to further decrease the amount of water shipped with coal, and to improve the coking characteristics of the coal at its destination, mechanical dewatering is followed by thermal drying. At U. S. Steel's-Alpheus preparation plant at Gary, West Virginia, approximately 50 percent of the total coal produced is in this fine size range, and two fluidized-bed dryers are used for the thermal drying step. The two fluidized-bed dryers are 14 feet in diameter and were designed by the Dorr-Oliver Company. Although the original design called for a rate of drying equivalent to 37 tons, of moisture per hour, presently they are removing twice that amount. This paper describes, the major problems encountered' in operating these dryers at the present, high capacities and how they were overcome.

Jan 1, 1963

By C. W. Baxter

Eveleth taconite company was formed in 1963 to mine and beneficiate taconite on the Mesabi range of Minnesota. Its thunderbird mine is located midway between the cities of Eveleth and Virginia, Minnesota, and the crude ore is transported by rail to its Fairlane plant approximately ten miles to the south of the mine, "figure 1". As is implied by the names of the mine and plant, the ford motor company is the principal owner of Eveleth taconite company, with an 85% interest, Oglebay Norton company holds the remaining 15% interest and also is the managing agent.

Jan 1, 1972

By G. Soni

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model has been validated in a series of laboratory batch flotation experiments, in which mono-sized glass beads are used as feeds. The experimental results are in good agreement with model predictions both in terms of grade and recovery.

Feb 23, 2014

By M. K. Buder

Over the years, electric utilities have been faced with declining steam-coal quality, rising coal prices, and increasingly rigid and costly environmental standards. As a result, many utilities are beginning to show an interest in coal cleaning to upgrade coal by improving its heating value and reducing its sulfur content. Among the primary questions that must be answered for these electric utilities is whether the cost of coal cleaning can be offset by the potential cost savings in coal transportation and utilization in power generation. In search of at least a preliminary answer to this question, the Electric Power Research Institute (EPRI) engaged Bechtel to perform a case-by-case economic study to examine the cost effects of using cleaned versus raw coal to fuel new electric power plants. The results of two of the seven cases studied which involved western coals - one from Montana and another from Utah - are reported in this paper. Coal cleaning appeared to be a cost effective option for the Utah coal, but only marginally economical for the Montana coal. These cost results are expected to change to favor coal cleaning to a greater extent with the application of the final revised New Source Performance Standards regulating SO2 emissions just issued by the EPA. The study was based on the regulation originally proposed by the EPA under the 1977 Clean Air Act Amendments.

Jan 1, 1979

By V. J. Hucka

A 0.5 m (20 in) diameter high pressure natural gas pipeline crosses over a coal mine located in Central Utah. Ground movement induced by the mining operation could possibly place excessive strain on the pipeline causing it to rupture. The mining operation extracts coal from two seams using the room and pillar method. The seams are situated one on top of the other and both lie directly under the pipeline. At present, only the upper seam is being mined beneath the pipeline. However, in the future, the mining operation of the lower seam will also affect the pipeline. As would be expected, mining of both coal seams causes surface subsidence. This is especially true when the pillars are extracted during retreat.

Jan 1, 1983

By R. L. Grayson, F. Giana, R. Aspinwall

Small-mine and contractor Fatal Incidence Rates have been a problem for over 20 years in the coal industry, and the rates persist as unacceptably high. This paper briefly retraces historical information and data on the continuing problem and recounts the many unsuccessful efforts and initiatives to address the problems effectively. Next the results of a review of international literature on addressing the problems are presented. After focusing on a method to pinpoint the trouble spots more specifically through a nested data analysis, suggestions are provided on how the problem may potentially be addressed more systematically and effectively in the U.S.

Jan 1, 2006

By Ernest E. Thurlow

"Western Coal" in this paper is limited to those deposits of subbituminous coal and lignite in the States of Montana, Wyoming, and North Dakota. The characteristics of the coal are discussed as well as the history of mining and current mining operations for steam coal. The future of the region is tied closely to the ultimate conversion of coal to oil and gas products. Problems of industrial water supply and environmental considerations are covered together with a brief review of current legislation's actions affecting strip mining.

Jan 1, 1973

By Clinton A. Hollingsworth

The Flotaire Flotation Cell is a simple, efficient hydraulic/pneumatic Flotation Cell that has no moving parts. It is normally used in conjunction with a surfactant (frother) in which case the combination is known as "The Flotaire System". On many ores, metallurgical efficiencies are substantially increased and operating costs reduce. For example, in floating phosphate rock, it is not unusual for BPL recovery to be increased more than 10%, the major increase being due to floating coarse phosphate, up to 14 mesh, and the difficult to float phosphate. Substantial improvements have also been made on coal, mica, vermiculite, kaolin, barite, copper, etc.

Jan 1, 1981

Scattered north and south along a 161-km (100-mile) stretch of Interstate 80, Newmont Min¬ing Corp. owns four active mining properties in Nevada?s northern high desert ? Carlin Trend Operations, Midas, Twin Creeks and Phoenix. Among the four, there are nine openpits, five underground mines and 14 processing facilities. While gold is the predominant ore, silver and copper are also produced. And in a move to hold down energy costs, Newmont built and owns the 200-MW (net), coal-fired TS power plant. This plant provides about 65 percent of the power used for Newmont?s own operations, while the rest is sold to NV Energy, which services Nevada and northeastern California. Bringing the Phoenix Mine ? Newmont?s newest in Nevada ? on-line presented many developmental and operational challenges. Located about 19 km (12 miles) southwest of the town of Battle Mountain, the general area had been home to prospectors and other mining companies since the 1860s. But any profitability in developing the lower grade gold, copper and silver deposit at Phoenix proved elusive, with Battle Mountain Gold being the last company to make an attempt. When Newmont acquired Battle Mountain Gold and its Phoenix reserves in 2001, the lower grade of ore was not a deterrent. Newmont found Nevada-wide cost savings synergies for maximizing profit during the depressed gold market of the late 1990s. The new property was aptly renamed the Phoenix Mine, a nod to its rising from the ashes of the dreams and efforts of previous mine owners.

Jan 2, 2010

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By James W. Marold

Tunnel and shaft plugs have been designed to assist in construction of new and rehabilitation of existing tunnels and shafts. Tunnel plugs have been used to provide construction access for side by side tunnels, separation of raw and treated water, and to allow operation of one tunnel during construction of a nearby tunnel. Shaft plugs have been used to seal up surface openings to tunnels and to prevent seepage of water to the surface through adjacent tunnels or shafts. The design construction details of tunnel and shaft plugs are provided. Typical examples of tunnel and shaft plugs are provided.

Jan 1, 2008

By Z. Mullard

The introduction of social media platforms has ushered in a new era of interaction and information exchange, which impact business-to-society relationships. Mining companies are closely watching these platforms, as the industry takes a cautious approach to control flows of information. This paper explores the risks, challenges and opportunities of using social media, based on a qualitative mixed methods investigation with stakeholders from the Canadian mining industry. Generational and language barriers, misunderstanding and limited motivation from regulators make implementing social media platforms challenging and risky at an organizational level. The benefits of social media include being able to mobilize communities and share information in real time. Despite the challenges, the study found that 62% of mining stakeholders are incorporating social media tools, mostly in an ad hoc manner. Flexible strategies for transparent communication and public engagement are creating new opportunities for information exchange.

Jan 1, 2011