Search Documents

By J. Piper

Markets and Production Beryllium (Be), an extremely light metal, is used in many specialty applications. It the lightest element in Group 2A of the periodic table, with a specific gravity of 1.85 gm/cc, and a high melting point of 12850C (Calvert, 2004). The functional properties of beryllium are stiffness, strength, dimensional stability, resistance to corrosion from acids, and electrical and thermal conductivity. The ability to reflect neutrons and transmit x-rays, makes beryllium irreplaceable in uses such as precision optical components, inertial guidance systems, and in nuclear reactors (Anon, 1993). Beryllium is used in Cu alloys to strengthen and reduce corrosion in copper wire, and in lightweight oxide ceramics that are used as heat sinks, and as electrical insulators. The market revenue of beryllium can be broken down into the seven major groups below, and are plotted on the pie chart in Figure 1 (Anon, 2005). 1.) Telecommunications & Computer 2.) Magnetic & Optical Data Storage 3.) Aerospace and Defense 4.) Automotive Electronics 5.) Industrial Components 6.) Appliance, and 7.) Other.

Jan 1, 2007

By J. MacFadyen

The U.S. cement industry experienced its best year ever during 2004 in terms of production and shipments of cement. Clinker, portland and masonry cements production and shipments were up considerably. Clinker production as reported to the U.S. Geological Survey (USGS) was 87.75 Mt (96.73 million st), an increase of 5.4 percent. Gray and white portland cement production from domestic and imported clinker was estimated to be 91.6 Mt (101 million st), up 5 Mt (5.5 million st) from 2003.

Jan 1, 2005

By B. K. Blashich

In responding to mine fires and explosions, accurate and timely analysis of the mine atmosphere is critical in making decisions regarding firefighting, mine rescue and mine recovery operations. For many years instantaneous analyses were available to rescue workers using handheld or portable gas detection equipment, including infrared, electrochemical, or catalytic measuring devices for a limited number of specific gases such as oxygen, methane, carbon monoxide and carbon dioxide. Instantaneous sensing technology is not available for all gases, such as nitrogen and hydrocarbons, found in a mine fire atmosphere and cross-sensitivity can be a problem with this technology. For these reasons, air samples are collected for injection into a gas chromatograph for a complete and accurate analysis for all gases including oxygen, nitrogen, methane, carbon monoxide and carbon dioxide, as well as ?fire gases? such as hydrogen, ethylene, ethane, and acetylene. This method requires additional time for transporting the samples to the laboratory near the mine, as well as an instrument operator to inject the samples for analysis. The use of a portable micro gas chromatograph with a continuous and automatic injection system has been implemented by the Mine Safety and Health Administration (MSHA) during mine recovery operations. The device directly samples the mine atmosphere from an underground location every twelve minutes and automatically analyzes the samples for all of the mine fire gases. The portable unit utilizes micro technology and the operating software has been modified to perform the calculation of sample results in and Excel® spreadsheet without user interaction. This paper describes the micro gas chromatograph system and its use at a recent mine recovery operation. The automated remote operation of the micro gas chromatograph has been shown to be a good alternative to infrared and electrochemical sensors used for mine atmosphere analysis.

Jan 1, 2009

By Edmond J. O’Donovan

South Bulga is a new longwall operation located in the Hunter Valley coal-mining region in Southeastern Australia. The mine’s objective is to achieve productivity levels significantly higher than the current industry average. From the day longwall production began, South Bulga’s output was below both budget and industry expectations, primarily because of the poor performance of the conveyor system. In the past, conveyor systems have been seen as an adjunct to the mine plan, not as an integral part. At past production levels, this approach may have been acceptable. In today’s mining operations, the conveyor system must be treated as integral and vital to the mining operation. The conveyor system is analogous to the vascular or circulatory system of the human body. Of itself, the system does not do anything, but if it is not functioning satisfactorily, the mine cannot operate.

Jan 1, 1996

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.

By Gary B. Glass

In 1997, 92.3% or 235.7 Mt (259.8 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River coalfield. The mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft). The thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash and 19.98 MJ/kg (8,590 Btu/lb.). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coalbeds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 289 Mm3/a (10.2 billion cu ft/year). This production is occurring west and downdip from the coal mines and is increasing each year.

Jan 1, 1998

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By D. Brandt

The Dos Pobres Mine is a copper oxide heap-leach operation located near Safford, AZ. Mine production is 163 kt/d (180,000 stpd) with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority. The engineering department began a project to improve fragmentation through blasting and thus increase throughput in the crushing system. It soon became clear that input from other departments was going to be required to make this a safe and economical project. Therefore, the crush and convey and ore control departments worked together to evaluate all available data on blast patterns and explosive loads and tracked performance and results. Using image analysis, drill energy index and databases, improved fragmentation size has been achieved and results have been verified while controlling costs.

Jan 1, 2011

By Michelle Mangione, John Kuyt, Zili Li, Michael Mooney

"Twin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world.A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a better understanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This article discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link project overview. The Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with more than 7 km (4 miles) of twin-bore road tunnels, two lanes each, with several caverns, interchanges and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a public-private partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5-m (41-ft) double-shield Herrenknecht tunnel boring machines (TBM) (Harding & Francis, 2013). The TBMs were used in earth pressure balance- (EPB) type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1-m (39.8-ft) diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in nine segments + one key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis (Harding & Francis, 2013). Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Mar 1, 2017

By Z. Jin, D. DePaoli, P. Zhang

"Phosphogypsum is a byproduct created during the production of industrial wet-process phosphoric acid. This study focused on recovering rare earth elements (REEs) from a Florida phosphogypsum sample and investigated the effects of removing detrimental impurities such as phosphorus pentoxide (P2O5 ), uranium (U) and fluorine (F) during the leaching process. Experimental results indicated that REE leaching efficiency increased rapidly, reached a maximum and then began to decrease with sulfuric acid concentrations ranging from 0 to 10 percent and temperatures ranging from 20 to 70 °C. At a sulfuric acid concentration of 5 percent and leaching temperature of 50 °C, REE leaching efficiency obtained a maximum value of approximately 43 percent. Increasing the leaching time or liquid/solid ratio increased the leaching efficiency. The leaching efficiencies of P2O5, U and F consistently increased with sulfuric acid concentration, temperature, leaching time and liquid/solid ratio within the testing ranges. A fine-grain gypsum concentrate, sized smaller than 40 µm, was separated from leached phosphogypsum through elutriation, in which the P2O5, U and F content levels were reduced by 99, 70 and 83 percent, respectively, from their content levels in fresh phosphogypsum. IntroductionPhosphogypsum is a byproduct generated during the industrial wet process of phosphoric acid production, in which sulfuric acid is used to digest phosphate rock. Gypsum (CaSO4·2H2O), the main component of phosphogypsum, usually accounts for 65 to 95 percent of phosphogypsum by weight.There are small quantities of impurities in phosphogypsum, such as phosphates (H3PO4, Ca(H2PO4)2·H2O, CaHPO4·2H2O and Ca3(PO4)2), fluorides (NaF, Na2SiF6, Na3AlF6, Na3FeF6 and CaF), sulfates, trace metals and radioactive elements (Rutherford, Dudas and Arocena, 1996). Global phosphogypsum generation is estimated at 200 Mt/a (Parreira, Kobayashi and Silvestre, 2003; Yang et al., 2009), but only about 15 percent is recycled as building materials, agricultural fertilizers or soil stabilization amendments (Tayibi Choura and Lopez, 2009)."

Jan 1, 2017

By Yanli Huang, Qiang Sun, Jixiong Zhang, Yuzhuo Jiang, Dan Ma

Mining accidents due to inrushing water are caused by sudden changes in seepage owing to structural damage to key strata of the aquiclude. The backfill mining method can be used to control the movement of the strata, weaken the evolution of fractures owing to damage by key aquiclude strata (KAS), and control the channel for inrushing water. This study develops a mechanical model of a composite beam on a non-uniform elastic foundation of the KAS by analyzing the coupling relationship between the filling body and the key water-resisting layer of the aquiclude. Equations of the deflection-induced deformation, bending moment, and maximum tensile stress of the KAS are analyzed, formulae to calculate the allowable tensile stress and backfill materials’ compaction ratio (BMCR) to ensure structural stability are derived, and are used to provide the critical BMCR for their structural instability. The results of field measurements show that the subsidence of the roof was 600–700 mm with an average BMCR of 80.63%. Damage to the overlying strata was controlled to ensure safe mining and the disposal of solid waste from the aquifer. The research here is useful for ensuring safety during mining while protecting water resources.

Jul 12, 2022

By J. H. Hammarstrom, S. M. Fortier, W. C. Day, S. J. Ryker, R. R. Seal

"The United States’ supply of critical minerals has been a concern and a source of potential strategic vulnerabilities for U.S. economic and national security interests for decades (for example, see Strategic and Critical Minerals Stockpiling Act, 1939). More recently, with the rapid increase in the types of materials being used in advanced technologies (Fortier et al. 2018a), and geopolitical events surrounding the supply of rare earth elements (Ting and Seaman, 2013), among other developments, the critical minerals issue has again achieved a high level of visibility within the U.S. government (Executive Order 13817 (2017)).In this paper, the U.S. Geological Survey (USGS) provides an overview of its ongoing focus on critical minerals through the agency’s core competencies in mineral information, mineral resource assessments, geologic and topographic mapping, geophysical surveys and mineral resource research. Aspects of the multifaceted critical minerals issue addressed here include:• Identifying minerals that meet the definition of “critical” provided in Executive Order 13817.• U.S. net import reliance for critical mineral raw materials.• Current status of domestic critical mineral resource assessments.• Current status of topographic and geologic mapping, and geophysical survey coverage of the United States.• The Earth Mapping Resources Initiative (Earth MRI) to support future critical mineral exploration.• Critical mineral potential of waste streams from extractive industries.Identifying minerals as criticalU.S. government agencies and other organizations use a number of existing definitions and criteria to identify a mineral or mineral material as critical, strategic or otherwise important. The executive order defined a “critical mineral” to be “(i) a nonfuel mineral or mineral material essential to the economic and national security of the United States, (ii) the supply chain of which is vulnerable to disruption, and (iii) that serves an essential function in the manufacturing of a product, the absence of which would have significant consequences for our economy and national security.” This definition is broadly consistent with that defined by the National Research Council (NRC, 2008) and may be summarized as “essential in use” and “subject to disruption of supply.” Virtually all of the dozens of critical minerals studies conducted since the 2008 NRC report have used some variation of this same definition (Hayes and McCullough, 2018)."

May 1, 2019

"A fire design innovation of the concrete lining of the Ohio River Bridges East End Crossing Tunnel has been developed. As a result from a fire suppression and tunnel ventilation system, the project design Heat Release Rate (HRR) was able to be constrained from 300 MW to about 50 MW. With this reduced HRR, concrete lining without passive fire protection may be acceptable, if the tunnel concrete lining will not result in explosive spalling during the designed fire event. Concrete explosive spalling test was proposed to verify this assumption. Since no standard concrete fire explosive spalling testing procedure exists, a project specific testing procedure was developed and fire tests conducted. From fire test results, it is concluded that the proposed tunnel concrete lining, in conjunction with the proposed fire suppressing and ventilation system, will not experience explosive spalling and does not require a passive fire protection system. INTRODUCTION The Ohio River Bridge East End Crossing Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The Tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining consists of 16 inches cast-in-place concrete lining and 20 inches invert slab, with a waterproofing system around the tunnel perimeter. Two (2) tunnel side drains and one (1) invert drain were provided for each tube. This paper describes the rational in assessing fire design requirements of the tunnel final concrete lining, to answer the question whether a passive fire protection system is needed or not."

Jan 1, 2016

By N. B. Pundari

Proper selection of large walking draglines, based on sound engineering principles and field experience, has not kept pace with the large capital expenditures needed to buy these stripping machines. The use of large walking draglines for stripping overburden in US surface coal mines grows steadily, but equipment selection continues to pose problems. An improper size, model, make, or spoil reach selected for a particular stripping application results in additional, unnecessary coal production costs. Large walking draglines are being used to dig deeper tar sands at the Syncrude operations near Fort McMurray in Northern Alberta, Canada. This application is compared with typical deep digging operations and dragline use prevalent at typical US strip mines.

Jan 4, 1981

By A. A. Bilgin

The prevention of acid mine drainage (AMD) in situ is more attractive than down-gradient treatment alternatives that do not involve source control. AMD source control can be achieved by shifting the microbial activity in the sulfidic rock from pyrite oxidation to anaerobic heterotrophic activity. This is achieved by adding biodegradable organic carbon amendments to the sulfidic rock. This technique was applied to an abandoned coal mine pool in Pennsylvania. The pool had a pH of 3.0 to 3.5. Following treatment, near-neutral pH and decreased effluent heavy metal concentrations were achieved. In situ bioremediation by the enhancement of bacterial iron and sulfate reduction is a promising technology for AMD prevention.

Jan 1, 2007

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By B. Das, D. D. Mishra, M. I. Ansari

Experiments conducted with a 75-mm-diem hydroryclone have shown it is possible to obtain an iron ore concentrate containing 60% Fe. 2.65% SiO2, and 4.0% Al2O3 from Barsua iron-ore washing-plant slimes. About 60% of the iron values are recovered from slimes containing approximately 49% Fe, 8.9% A1203 and 11% SiO2. The obtained products can be used in the sinter feed for iron and steel making. The key to achieving process success lies in establishing the correct cut point (d50) of the hydrocyclone through the manipulation of operating and design variables, such as spigot and vortex finder diameter, solids concentration and operating pressure. The cyclone efficiency is represented by the partition curve. The cyclone performance, evaluated mathematically from the reduced efficiency curve, is represented by the equation Y = 100[1 -exp(-axb)], where: •X = did 50, •Y = corrected of efficiency (%) and •a and b are constants.

Jan 1, 1994

By A. M. Tonnos

Underground mining has yet to see an industry wide solution for control of their ventilation systems due to the complexity and sensitivity of the underground environment. Complexity arises from multi-level, multi-zone operations and sensitivity is associated with the impact that changes in equipment status and output have on air flows and quality throughout the mine. Our approach to solving this challenge incorporates system modeling and industrial control systems in a unified architecture. Although this approach can be applied to other processes and industries, this paper will cover the theoretical and practical aspects of an integrated model-control system (MCS) as it applies to underground mining ventilation.

Jan 1, 2009

By S. K. Singh

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

Floor heave events in underground mining often happen suddenly and cause risk to workers and equipment. Reducing the risk of floor heave must be addressed in mining layout design. To improve that design one must understand the significant parameters that are correlated to the occurrence of floor heave. To accomplish that goal, researchers from the National Institute for Occupational Safety and Health (NIOSH) completed a numerical study using FLAC3D, taking advantage of its strain softening and ubiquitous joint capabilities to better simulate the floor heave and caving mechanisms involved at an actual mine site.

Jan 7, 2020